ICON DIGITAL 2502007001 GUITAR WIRELESS SYSTEM-RECEIVER User Manual Beetles
ICON INTERNATIONAL DIGITAL LIMITED GUITAR WIRELESS SYSTEM-RECEIVER Beetles
Contents
- 1. USERS MANUAL 1
- 2. USERS MANUAL2
USERS MANUAL2
Quick Setting up and Using Your Beetles System Setting up your Beetles Wireless system is easy and it won't take you more than few minutes to finish. Follow the below steps:1. Unpack your Beetles Wireless System. You may save all the packing materials for packing purpose in the future. 2. Check if your Beetles Receiver are having the same RF Channels (U1-U10, please see P.9 for ICON Frequency Chart) labels as your Beetles Transmitter. They needed to be same for your Beetles wireless system working. 3. Insert a standard 9V alkaline battery into the Receiver's Battery Compartment or plug in the provided power adapter into the DC 9V jack. 4. Place the Receiver on the floor and lift up its dual antennas to the vertical position. 5. Make sure the powers are off for your Beetles Receiver and Transmitter. 6. Plug the cable jack to the output connector of your Receiver and connect it to your Amplifier or Mixer (make sure the power is off for your Amplifier or Mixer). 7. Turn the Receiver's Volume Control knob to the most anti-clockwise position (i.e. Min. Level) and push the Power knob to turn it on. The "ON" LED should light red. 8. Insert a standard 1.5V battery into your Beetles Transmitter Battery compartment. Then, turn the power on. The "ON" LED should light once. 9. Check the "RF" LED on your Receiver, it lights (green) indicating the Receiver receives good therefore signal from your Transmitter. User's Manual Quick Setting up and Using Your Beetles System Notice Please follow the below procedure to change the angle of the jack of your transmitter. Press the knob down by your finger as shown on Diagram 1 Then rotate the jack, while you pressing the knob down, to your desire angle. You should feel the "Click" Position when the jack turned to 90o or 120o. User's Manual Quick Setting up and Using Your Beetles System 10. Now, it's time to set your audio levels. Turn on your amplifier or mixer and keep its level to minimum. 11. Turn the output level of your electric/acoustic guitar or bass to the maximum and start playing at a normal performance level and keep observing the Beetles Receiver "RF" and "PEAK" LED. If PEAK LED stay on even Receiver's volume control is set to its minimum, switch on your Beetles Transmitter's "15dB Pad " switch. Otherwise, turn the volume control anti-clockwise until "PEAK" LED occasionally blinks red during the very loudest passages, then back it off just slightly; this will ensure maximum signal to noise ratio. 12. Finally, raise the level of your amp or mixer until the desired volume is reached. 13. If you hear distortion or Beetles Receiver "PEAK " LED lights red even with the "15dB Pad" engaged and receiver level control is set to minimum, please reduce the output level of your instrument until the "PEAK" LED no longer stay on all the time. Conversely, if you hear weak and noise signal at the desired volume level, make sure your instrument is set to maximum output level; the " 15dB Pad " is not engaged and the Receiver volume control is turned up. User's Manual 902.125MHz 903.500MHz 905.375MHz 907.875MHz 908.500MHz 910.375MHz 912.750MHz 915.500MHz 916.250MHz 918.375MHz 920.125MHz 921.500MHz 922.375MHz 923.500MHz 925.800MHz 926.500MHz U1 U2 U3 U4 U5 U6 U7 U8 U9 U10 U11 U12 U13 U14 U15 U16 Services If your Beetles Wireless System needs the servicing, follow these instructions. 1. Ensure the problem is not related to operation error or external system devices. 2. Keep this owner's manual. Don't send the owner's manual to the service centre. 3. Pack the unit in its original packaging including end card and box. This is very important. If you have lost the packaging, please make sure you have packed the unit properly. ICON is not responsible for any damage that occurs due to nonfactory packing. 4. Ship to the ICON technical support centre or the local return authorization. U.S. OFFICE: ICON Digital Corp. 2222 Pleasant View Road Suite #1 Middleton, WI 53562 USA infous@icon-global.com ASIA OFFICE: ICON (Asia) Suite Nos. 807-810, 8/F., Sunley Centre, No. 9 Wing Yin Street, Kwai Chung, NT., Hong Kong. Infoasia@icon-global.com For additional update information please visit our website at: www.icon-global.com User's Manual 11 www.icon-global.com info@icon-global.com FCC NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USERâS AUTHORITY TO OPERATE THE EQUIPMENT. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 9 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:ac26e6c9-80dd-4fba-83d5-274b62124aa6 Producer : pdfFactory Pro 2.10 (Windows XP Chinese) Create Date : 2007:08:27 16:01:55Z Creator Tool : pdfFactory Pro www.fineprint.com.cn Modify Date : 2008:01:25 17:49:08+08:00 Metadata Date : 2008:01:25 17:49:08+08:00 Document ID : uuid:c54a13a7-4da8-4843-896b-9f394a4e1c51 Instance ID : uuid:f5171b1b-cb56-40fa-8039-2170b6f75022 Format : application/pdf Creator : yan Title : Beetles.cdr Author : yanEXIF Metadata provided by EXIF.tools