ICP DAS ZBUPS0001 ZigBee Module User Manual ZB UPS01 ok

Download:
Mirror Download [FCC.gov]
Document ID	1282168
Application ID	new6DQ1jBTF4baOcyuximA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	48.24kB (602976 bits)
Date Submitted	2010-05-17 00:00:00
Date Available	2010-05-17 00:00:00
Creation Date	2010-05-13 09:39:52
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2010-05-13 10:08:34
Document Title	Microsoft Word - ZB-UPS01 User Manual -ok.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	kellyweng

Product #:ZB-UPS01
ZB-UPS01
ZigBee Transceiver Module
User Manual
Version 0.9
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 1/14
Product #:ZB-UPS01
TABLE OF CONTENTS
GENERAL INFORMATION ………………….……………..…….…3
POWER SAVING MODES …………………….……….…………….4
CONNECTORS PIN CONFIGURATION … …….….….….……….5
ELECTRICAL SPECIFICATIONS ……………..…………………...6
DESIGN GUIDE TO AVOID RF INTERFERENCE …………….....7
RF PERFORMANCE TEST DATA …………………….….…….…..10
REFERENCE REFLOW TEMPETURE CURVE…………………..11
REFERENCE DOCUMENTS………..…………………..…………...11
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 2/14
Product #:ZB-UPS01
Revised Date: Apr.14, 2010
1. GENERAL INFORMATION
The ZB-UPS01 is a miniature 2.4 GHz Direct Sequence Spread Spectrum 802.15.4 transceiver. It
includes all RF hardware and a micro-controller to manage the communications link. The
micro-controller manages all communications task including configuration, data packaging, and
clear channel selection. The result is a complete wireless data communications solution.
The ZB-UPS01 package is unique because of its small form factor (32 x 23 mm ), It has an
on-board chip antenna and the availability of external dipole antenna I-PEX connector. No
competitive products can offer a solution as flexible, convenient, and easy to integrate.
Models
• ZB-UPS01: Includes PA/LNA, on-board chip antenna, MCU SiliconLabs C8051F340
Features
• 32 x 23 mm PCBA package with 2 connectors
• Utilizes globally available 2.4 GHz ISM band
• Programmable Transmit Power Output, max. 9dBm.
• Complete IEEE 802.15.4 Spec. compliant.
• Typical Receiver Sensitivity –101dBm.
• Typical Data Rate 250Kbps.
• Multiple Low Power Operating modes
• Meet RoHS Requirement
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 3/14
Product #:ZB-UPS01
2. POWER SAVING MODES
The ZB-UPS01 includes several low power operating modes to permit the most efficient use of the
available power. Below are descriptions of the available selections.
ACTIVE: In Active Mode, all ZB-UPS01 circuits are powered and available for immediate action.
This includes the RF receiver which actively monitors the air for an incoming communications
request. Two sub-modes are classified as TX-ACTIVE and RX-ACTIVE. The current
consumption of TX-ACTIVE is 44 mA while RX-ACTIVE is 38 mA.
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 4/14
Product #:ZB-UPS01
3. CONNECTORS PIN CONFIGURATION
ZB-UPS01/ZB-UPH01 uses Silicon-Lab C8051F340 as MCU. It is an 8051 base MCU and
reserves 10 GPIO pins for external controlling by application. Each pin can be a general I/O pin
and programmed it by user directly. Furthermore, most of these pins can be used as special purpose
function. Thereof TX, RX pins can be programmed as UART for data communication. For
example, user is easy to connect these pins with RS485 transceivers such as 75176, MAX485.
J1 Pin Configuration
Signal
Pin
Description
C2CK
Clock signal for the C2 Debug Interface.
C2D
Bi-directional data signal for the C2 Debug Interface.
VCC
3.3 Volt power for the ZB-UPS01
TX
GPIO, also used as UART TX.
GND
Ground
RX
GPIO, also used as UART RX.
GPIO1
Bidirectional input/output Pin. It also can be programmed as analog to
digital converter (ADC1)
GPIO2
Bidirectional input/output Pin. It also can be programmed as analog to
digital converter (ADC2)
J2 Pin Configuration
Signal
Pin
Description
GPIO3
Bidirectional input/output Pin. It also can be programmed as analog to
digital converter (ADC3)
GPIO4
Bidirectional input/output Pin. It also can be programmed as analog to
digital converter (ADC4)
GPIO5
Bidirectional input/output Pin.
GPIO6
Bidirectional input/output Pin. It also can be programmed as analog to
digital converter (ADC5)
GPIO7
Bidirectional input/output Pin. It also can be programmed as analog to
digital converter (ADC6)
GPIO8
Bidirectional input/output Pin.
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 5/14
Product #:ZB-UPS01
4. ELECTRICAL SPECIFICATIONS
Absolute Maximum Rating
VCC
3.6V
Storage temperature
-40°C to +120°C
Operating temperature Range
-30°C to +80°C
WARNING: Exceeding any of these ratings will void the warranty and may damage the device
Parameters
Supply Voltage for RF, analog and digital circuits
Digital I/O Pin Input High Voltage
Min
Typ
Max
Units
3.3
3.6
2.0
Digital I/O Pin Input Low Voltage
0.8
3.3
Analog Input Pin Input Voltage
I/O Pin Output High Current
mA
I/O Pin Output Low Current
14
mA
I/O Pin Input High Current
10
uA
I/O Pin Input Low Current
10
uA
Current Consumption
ACTIVE TX Mode @ 9 dBm
44
mA
ACTIVE RX Mode
38
mA
dBm
-101
dBm
Output Power
Wireless Receive Sensitivity
Selectable Channels
16
Frequency Band
2.400
Antenna Output Impedance
Confidential
Doc. #: ZB-UPS01 Reference Note 
channel
2.835
50
GHz
Ohms
Page 6/14
Product #:ZB-UPS01
5. DESIGN GUIDE TO AVOID RF INTERFERENCE
When RF module put on an application board(mother board), to minimize the RF signal
interference, the best way is to define an isolation area. This area should have no any trace or
grounding pad. Here are some layout suggestions for mother board.
Suggestion 1: Place RF board aside mother board. (Let antenna part outside mother board is
better) Make sure no trace and grounding pad under the must isolate area. Please see the drawing
as below.
Must Isolate Area
Prefer Isolate Area
Module Board
Via
Mother Board
Antenna
Suggestion 2: Place RF board at the corner of mother board. Make sure no trace and
grounding pad under the must isolate area. Please see the drawing as below.
Must Isolate Area
Prefer Isolate Area
RF Module Board
Via
Customer's Mother Board
Antenna
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 7/14
Product #:ZB-UPS01
Suggestion 3: If you couldn’t put RF board at one side or at the corner of mother board. You
must make sure no circuit trace and grounding pad under the must isolate area, and at least reserve
extra 3 mm space as safety area. Please see the drawing as below.
Must Isolate Area
Prefer Isolate Area
RF Module Board
Via
Customer's Mother Board
Antenna
For all of above suggestions, try to extend isolation area from must area to prefer area. Please
see the drawing as below. The more isolation area, the better RF performance。
Must Isolate Area
Prefer Isolate Area
RF Module Board
Via
Customer's Mother Board
Antenna
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 8/14
Product #:ZB-UPS01
Must Isolate Area
Prefer Isolate Area
RF Module Board
Via
Customer's Mother Board
Antenna
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 9/14
Product #:ZB-UPS01
6. RF PERFORMANCE TEST DATA
Return Loss: -17.5dB
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 10/14
Product #:ZB-UPS01
7. REFERENCE REFLOW TEMPETURE CURVE
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 11/14
Product #:ZB-UPS01
8. Reference Documents
13.1 UBEC UZ2400 datasheet
13.2 UBEC UP2268 datasheet
13.3 ACX AT5020 datasheet
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 12/14
Product #:ZB-UPS01
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
●
Reorient or relocate the receiving antenna.
●
Increase the separation between the equipment and receiver.
●
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
●
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 13/14
Product #:ZB-UPS01
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm
separation with the antenna while this end product is installed and operated. The end user has to be
informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end user has to also be informed that any changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate this equipment. If the size of
the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be
available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and (2) this device must
accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
Q6MZBUPS0001 ". If the size of the end product is larger than 8x10cm, then the following FCC part
15.19 statement has to also be available on the label:
This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Confidential
Doc. #: ZB-UPS01 Reference Note 
Page 14/14

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-702
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2010:05:13 10:08:34+08:00
Create Date                     : 2010:05:13 09:39:52+08:00
Metadata Date                   : 2010:05:13 10:08:34+08:00
Format                          : application/pdf
Title                           : Microsoft Word - ZB-UPS01 User Manual -ok.doc
Creator                         : kellyweng
Document ID                     : uuid:33a74027-4616-4cb6-97d6-5fd16fbb70a5
Instance ID                     : uuid:505b47d4-e564-495f-9882-db15caafdc77
Page Count                      : 14
Author                          : kellyweng

EXIF Metadata provided by EXIF.tools