ICP DAS ZTM-WP RF Modem User Manual 06 User s Manual V3

Download:
Mirror Download [FCC.gov]
Document ID	2676584
Application ID	3h/duRRLbzo9ekCo9wV9KA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.96kB (87000 bits)
Date Submitted	2015-07-13 00:00:00
Date Available	2016-01-11 00:00:00
Creation Date	2015-07-06 18:55:04
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2015-07-06 18:55:04
Document Title	Microsoft Word - 06_User's Manual_V3.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Tiffany_Kao

ZTM-W / ZTM-P User’s Manual
Warranty
All products manufactured by ICP DAS are under warranty regarding
defective materials for a period of one year, beginning from the date
of delivery to the original purchaser.
Warning
ICP DAS assumes no liability for any damage resulting from the use
of this product. ICP DAS reserves the right to change this manual at
any time without notice. The information furnished by ICP DAS is
believed to be accurate and reliable. However, no responsibility is
assumed by ICP DAS for its use, nor for any infringements of patents
or other rights of third parties resulting from its use.
Copyright
Copyright © 2013 by ICP DAS. All rights are reserved.
Trademarks
Names are used for identification purpose only and may be
registered trademarks of their respective companies.
ZTM-WP User’s Manual, Ver. 1.0
Page 1
1. Introduction
The ZTM-W / ZTM-P is a FCC certified design and a small-sized wireless-UART converter solution
consisting of a micro controller unit with RF transceiver and a RF power amplifier front-end, or often
called the low-noise amplifier (LNA), and it offers excellent the sensitivity. The ZTM-W / ZTM-P is
based on the 2.4 GHz IEEE 802.15.4 standard, and either the function of radio-frequency or ZigBee
firmware is available to be used. It can be controlled through an external host/system microcontroller
or external evaluation software through the UART interface. We use the same hardware but the
different firmware to achieve the RF Modem, ZigBee Coordinator or ZigBee Router.
2. Models
ZTM-W / ZTM-P module is intended for OEM integrator. The module includes PA/LNA and the
either PCB Antenna or Connector of Dipole Antenna. It depends on market positioning to install
firmware.
3. Features















37.07mm x 25mm PCB
Two 1x9 and one 1x6 pin spacing 2.00mm connector
Utilizes globally available 2.4 GHz ISM band
Control and Configuration with specific commands via UART@115.2Kbps
Programmable Transmit Power Output, Max 19 dBm
Typical Receiver Sensitivity -97dBm
Typical Data Rate 250Kbps
Complete IEEE 802.15.4 Spec. compliant
Fully Compliant with ZigBee Pro (ZigBee 2007)
65527 unique node addresses
Typical transmission range 700 meters (Line of Sight)
Required Supply Voltage: 2 to 3.6VDC
Operating Temperature: -30°C to +80°C
Storage temperature: -40 to +80°C
RoHS.
4. Protocol Overview
The bidirectional data exchange between an external host/system microcontroller and the ZTM-WP
module uses the hardware UART and follows the RS232 protocol. This RS232 protocol is summarized
in Table 1.
Table 1. Host RS232 Serial Interface Communication Parameters
PARAMETER PARAMETERS
DESCRIPTION
Baud Rate
115.2Kbps
Start Bits
Data Bits 8
Stop Bits 1
Parity None
None
ZTM-WP User’s Manual, Ver. 1.0
Page 2
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
Responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other
antenna or transmitter.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
ZTM-WP User’s Manual, Ver. 1.0
Page 3
IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC
compliance requirement of the end product, which integrates this module.
20cm minimum distance has to be able to be maintained between the antenna and the users for the
host this module is integrated into. Under such configuration, the FCC radiation exposure limits set
forth for an population/uncontrolled environment can be satisfied.
Any changes or modifications not expressly approved by the manufacturer could void the user's
authority to operate this equipment.
USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm
separation with the antenna while this end product is installed and operated. The end user has to be
informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end user has to also be informed that any changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate this equipment. If the size of
the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be
available in the user manual: This device complies with Part 15 of FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference and (2) this device
must accept any interference received, including interference that may cause undesired operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
Q6M-ZTM-WP". If the size of the end product is larger than 8x10cm, then the following FCC part
15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference and (2) this device must accept any interference received, including interference that may
cause undesired operation.
ZTM-WP User’s Manual, Ver. 1.0
Page 4

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Tiffany_Kao
Create Date                     : 2015:07:06 18:55:04+08:00
Modify Date                     : 2015:07:06 18:55:04+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - 06_User's Manual_V3.doc
Creator                         : Tiffany_Kao
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:448b1c0e-493d-4584-994e-f274dc19c359
Instance ID                     : uuid:b9f26b73-d429-4e67-80ac-c008911d6ee7
Page Count                      : 4

EXIF Metadata provided by EXIF.tools