ID Teck Co RF10 Door Access Controller User Manual manual
ID-Teck Co Ltd Door Access Controller manual
manual
MODEL : STAR RF10
PROXIMITY READER
OWNER’S MANUAL
Please read this instruction manual carefully
Contents
1. Important safety instructions ---------------- 3
2. General ---------------- 4
3. Specification ---------------- 4
4. Connection ---------------- 4
5. Operation ---------------- 5
6. Block diagram ---------------- 6
7. FCC Registration information ---------------- 7
8. Warranty and service ---------------- 8
- 2 -
IMPORTANT SAFETY INSTRUCTIONS
When using your door access controller, basing safety precautions should always be followed to
reduce the risk of fire, electrical shock, and injury to persons including following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product
3. Do not use liquid cleaners, or aerosol cleaners. Use a damp cloth for cleaning. if necessary, use a
mild soap.
4. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming pool.
5. This product should be operated only from the type of power source indicated on the marking
label. if you are not sure of the type of power supply to your home, consult your dealer or local
power company.
6. Never push objects of any kind into this product though the cabinet slots as they may touch
voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid
of any kind on the product.
7. To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified
serviceman when some service or repair work is required. Opening or removing covers may expose
you to dangerous voltages or other risks. incorrect reassembly can cause electric shock when the
appliance is subsequently used.
8. Unplug this product from the wall outlet and refer to qualified service personnel under the
following conditions:
a. When the power supply cord or plug is damaged or frayed.
b. If liquid has been spilled into the product
c. If the product has exposed to rain or water.
d. If the product doses not operate normally by following the operating instructions.
Adjust only those controls, that are covered by the operating instructions. Improper
adjustment of other controls in damage and will often require extensive work by a qualified
technician to restore the to normal operation.
e. If the product exhibit a distinct change in performance.
- 3 -
STAR RF10 Proximity Reader
1. General
The STAR RF10 is a new and an attractive 10cm read range Proximity Reader
which can be used in various industrial applications.(Access control, Factory
automation and extra) It supports Wiegand format and RS232C(option).
This proximity reader will ensure you its successful operations even in harsh
environments (vandal proof). The elegant looking reader case is designed to match
any interior decoration of ultramodern buildings.
Two color LEDs of green and red, inside digital buzzer sound will guarantee you an
accurate system operation
2. Specification
.Input Voltage : 12VDC
.Power : 12VDC 60mA(Recommand linear power supply)
.Modulation : PSK modulation
.Cabinet Color : Dark Gray
.Output Formats : 26 bits Wiegand, RS232C(Option)
.Operating Environment : 0°C ~ 60°C , 10% ~ 90% humidity
3. Connection
RED(+12V)
YELLOW(GND)
GREEN(DATA0)
WHITE(DATA1)
STAR RF10 CONTROLLER
- 4 -
WIRE COLOR TABLE
COLOR FUNCTION
RED +12V
GREEN DATA0
WHITE DATA1
YELLOW GND
4. Operation
. Connect DC 12V and Wiegand data lines to STAR RF10 proximity reader.
. Apply power and red LED of RF10 will lit.
. Approach RF card to the reader then reader will beep and green LED will lit
for a second then red LED lit again for next reading sequence.
. Reader will send 26 bits Wiegnad data to access controller.
(RS232C output format OPTION)
- 5 -
- 6 -
FCC REGISTRATION INFORMATION
FCC REQUIREMENTS PART 15
Caution: Any changes or modifications in construction of this device which are not
expressly approved by the responsible for compliance cold void the user's authority to
operate the equipment.
NOTE: This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
- 7 -
WARRANTY AND SERVICE
The following warranty and service information applies only to the U.S. For information in other
countries, please contact your local distributor.
To obtain in or out of warranty service, please prepay shipment and return the unit to the appropriate
facility listed below.
IN THE UNITED STATES
RF LOGICS, INC. Service center
3026 SCOTT BLVD,
SANTA CLARA, CA 95054
Tel. : (408) 980-0001
Fax.: (408) 980-8060
Email: webmaster@rflogics.com
Website : www.rflogics.com
OUTSIDE OF THE UNITED STATES
ID TECK CO., LTD. Service center
4F ACE TECHNOTOWER BLDG.
684-1 DUNGCHON-DONG, GANSUH-KU
SEOUL 157-030, KOREA
Tel. : 82-2-659-0055
Fax.: 82-2-659-0086
Email: webmaster@id-teck.com
Website : www.id-teck.com
Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to
prevent damage. Include the following information:
1. A proof-of-purchase indicating model number and date of purchase.
2. Bill-to address
3. Ship-to address
4. Number and description of units shipped
5. Name and telephone number of person to call, should contact be necessary
6. Reason for return and description of the problem.
Damage occurring during shipment is deemed the responsibility of the carrier, and claims
should be made directly with the carrier.
- 8 -