ID Teck Co STARRF30 Proximity Reader User Manual 285792

Download:
Mirror Download [FCC.gov]
Document ID	285792
Application ID	QzGAWpfdT7Gv/7w6px2puQ==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	94kB (1175041 bits)
Date Submitted	2002-11-25 00:00:00
Date Available	2002-11-25 00:00:00
Creation Date	2002-11-25 21:39:24
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2002-11-25 21:39:24
Document Title	Microsoft Word - 285792.DOC
Document Creator	PScript5.dll Version 5.2
Document Author:	fcc

STAR RF30+
PROXIMITY READER
USER’S MANUAL
Proximity Reader
ID TECK Co. Ltd.
RF30-20011104
STAR RF30+
PROXIMITY READER
CONTENTS
RF30-20011104
1. Introduction
page 3
2. Identifying supplied parts
page 3
3. Specification
page 3
4. Installation
page 4
5. Wire Color Table of the Reader
page 5
6. Wire Connection to Controller
page 5
7. Operation
page 6
8. FCC Registration Information
page 7
9. Warranty and Service
page 8
STAR RF30+
PROXIMITY READER
1. Introduction
The STAR RF30+ is an elegant looking and attractive 12" read range proximity reader which can be
mounted on any flat wall surface. The RF30+ uses the electronics module in epoxy potting that ensures
successful operations even in harsh environments.
The two-color LED of green and red and the inside Piezo buzzer sound will guarantee you accurate and
reliable system operations.
2. Identifying supplied parts
Please unpack and check the contents of the box.
Reader Module
RF30+ Bezel
Instruction
3. Specification
Read Range
Input Voltage/Current
Output Format
External Beeper control Input
External LED control Input
LED/Beeper
Color
Operating Environment
Overall Size(WxHxD)
Weight
RF30-20011104
Up to 12"(30cm)
DC 7V ~ 17V / Max. 170mA
26 bit Wiegand, Magstripe ABA Track II
Low Active, DC 0 ~ 12V, Max. 50 mA
Low Active, DC 0 ~ 12V, Max. 50 mA
2-Color LED(Red and Green) / Piezo Buzzer
Dark Gray
-31 ~ 149 (-35 ~ +65 ), 0~90% Humidity
5.2"x 6.2"x0.8"(130x154x20.5mm)
0.93 lbs (420g)
STAR RF30+
PROXIMITY READER
4. Installation
4-1. Wall Mount
Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical and drill one 1/2" hole for
the reader cable 1.7"(4.31cm) apart from the top hole.
(If you have installed an electric gang box then skip this step and go to step 4.2.)
4-2. Put reader cable into the center hole and install the reader module by using two
6-32 or M3 screws (Not included).
4-3. Put bezel on to the reader module then push bezel until you hear the locking sound.
RF30-20011104
STAR RF30+
PROXIMITY READER
5. Wire Color Table of the Reader
POWER
Power(DC +7V~+17V)
DC(+)
Power(DC Ground) DC(-)
(GND)
INPUT
Beeper control input
BEEP
LED control input
LED
OUTPUT(Wiegand Format)
Wiegand Data-0
Data-0
Wiegand Data-1
Data-1
OUTPUT(RS232 Format)
RS232(TX)
TX
OUTPUT(ABA Track II Format)
ABA(Card Present)
CP
ABA(Clock)
CLK
ABA(Data)
Data
Note: All ABA Track II outputs are open collector output.
6. Wire Connection to Controller
RF30-20011104
Red wire
Black wire
Blue wire
Yellow wire
Green wire
White wire
White wire
Orange wire
White wire
Green wire
STAR RF30+
PROXIMITY READER
7. Operation
7-1. Once power is applied, you should hear three beeping sounds and LED changes color to
red-green-red indicating that the reader is in standby mode after a successful initialization and
diagnostics.
7-2. Present proximity card to the reader until you hear the beeping sound and see the LED changes
color to Green. The reader will send the RF card data to the controller then the LED will change
color to Red again for the next reading.
7-3. LED Control:
To change the LED colors, you may connect the LED Control Input (Yellow wire) to
ground and the Green LED will turn on indicating that the reader is in standby mode.
Present proximity card and the LED will change color to Red then Green again for the next
reading.
7-4. Beeper Control:
In normal operation, the reader generates one beep when it reads a proximity card, however
additional beeps can be generated to improve indication for access status (granted or denied) by
forcing the beeper control input (Blue wire) to system ground level. The beeper will remain on as
long as the Blue wire is connected to system ground.
RF30-20011104
STAR RF30+
PROXIMITY READER
8. FCC REGISTRATION INFORMATION
FCC REQUIREMENTS PART 15
Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions;
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A Digital Device, pursuant to Part 15 of the
FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the radio or television off and on, the
user is encouraged to try to correct interference by one or more of the following measures.
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on another circuit.
4. Consult the dealer or an experienced radio/TV technician for help.
RF30-20011104
STAR RF30+
PROXIMITY READER
9. Warranty and Service
The following warranty and service information applies only to the United States of America and Republic of Korea. For the
information in other countries, please contact your local distributor.
To obtain in or out of warranty service, please prepay shipment and return the unit to the appropriate facility listed below.
IN THE UNITED STATES
RF LOGICS Inc. Service Center
3026 Scott Blvd.,
SANTA CLARA, CA95054
Tel.:
(408) 980-0001
Fax.:
(408) 980-8060
E-mail: rflogics@rflogics.com
Web-site: www.rflogics.com
OUTSIDE OF THE UNITED STATES
ID TECK CO., LTD. Service Center
5F Ace Techno Tower Bldg.,
684-1 Deungchon-dong, Gangseo-gu,
SEOUL 157-030, KOREA
Tel.:
+82 (2) 659-0055
Fax.:
+82 (2) 659-0086
E-mail: webmaster@idteck.com
Web-site: www.idteck.com
Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to prevent damage, include the
following information:
1. A proof-of-purchase indicating model number and date of purchase.
2. Bill-to address
3. Ship-to address
4. Number and description of units shipped.
5. Name and telephone number of person to contact.
6. Reason for return and description of the problem.
NOTE: Damage occurring during shipment is deemed the responsibility of the carrier, and claims should be made directly to
the carrier.
RF30-20011104

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2002:11:25 21:39:24-08:00
Modify Date                     : 2002:11:25 21:39:24-08:00
Page Count                      : 8
Creation Date                   : 2002:11:26 05:39:24Z
Mod Date                        : 2002:11:26 05:39:24Z
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : fcc
Metadata Date                   : 2002:11:26 05:39:24Z
Creator                         : fcc
Title                           : Microsoft Word - 285792.DOC

EXIF Metadata provided by EXIF.tools