ID Teck Co STARSR10 Proximity Reader User Manual

ID-Teck Co Ltd Proximity Reader Users Manual

Users Manual

PROXIMITY READER USER’s MANUAL Philips Mifare™ Compatible Proximity Reader
PROXIMITY READER IDTECK -2- 20031125 CONTENTS 1. Important Safety Instructions page 3 2. Product Introduction page 3 3. Features page 4 4. Identifying supplied parts page 4 5. Specification page 4 6. Installation page 5 7. Wire Color Table of the Reader page 5 8. Output Format page 6 9. Wire Connection to Controller page 7 10. Operation page 7 11. FCC Registration Information page 8 12. Warranty and Service page 9 13. RMA Request Form & A/S Request Form page 10
PROXIMITY READER IDTECK -3- 20031125 1. Important Safety Instructions When using STAR SR10/SR20 Philips Mifare™ Compatible Proximity Reader, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons. In addition, the following should also be followed: 1. Read and understand all instructions of the User’s Manual. 2. Follow all warnings and instructions marked on the product. 3. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. If necessary, use mild soap. 4. Do not use this product near water, such as bath-tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or swimming pool. 5. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your installation site, consult your dealer or local power company. 6. Never push objects of any kind into this product or through the cabinet slots as they may touch voltage points or short out parts that could result in fire or electric shock. Never spill liquid of any kind on the product. 7. To reduce the risk of electric shock, do not disassemble this product by yourself, but take it to qualified service whenever service or repair is required. 8. Unplug this product from the Direct Current (DC) power source and refer to qualified service personnel under these conditions: z When the power supply cord or plug is damaged or frayed. z If liquid has been spilled on the product. z If the product does not operate normally after following the operating instructions in this manual. z If the product exhibits a distinct change in performance. 9. Do not use this product under dusty or vibration circumstance. 2. Product Introduction The STAR SR10/ SR20 Philips Mifare™ Compatible Proximity Reader is an elegant looking 4" (10cm) read range proximity reader which can be mounted to any flat wall surface. The SR10/SR20 Philips Mifare™ Compatible Reader reads serial numbers from Philips Mifare™ Compatible cards and transmits the data to control panel in various output formats. The SR10/ SR20 uses the same epoxy-potted electronics module that ensures you successful operation even in harsh environments. The two-color LED of green and red and the piezo buzzer inside the reader will guarantee you accurate and reliable system operations.
PROXIMITY READER IDTECK -4- 20031125 3. Features - Philips Mifare™ Compatible Proximity Reader - Maximum 4" (10cm) reading range - External LED and Buzzer control inputs - 2-Color LED(Red and Green) Indicator and Buzzer sound - Output format selectable between 34-bit/26-bit Wiegand - Optional RS232 communication port - Operating voltage from 7V to 17VDC 4. Identifying Supplied Parts Please unpack and check the contents of the box. Reader Module SR10 Bezel or SR20 Bezel Instruction (1 ea) (1 ea) (1 ea) (1 ea) 5. Specification Read Range : Up to 4" (10cm) Read Format : Philips Mifare™ Compatible Proximity Card Format Operating Frequency : 13.56MHz Compatibility : ISO14443 type A Power : DC 7V ~ 17V, Max. 150mA Output Format : 34-bit or 26-bit Wiegand, Optional RS232 communication port External LED/ Buzzer control Input : Low Active, DC 0 ~ 5V, Max. 50 mA LED/ Buzzer : Two-color LED(red and green)/ Piezo Buzzer Color : Dark Pearl Gray Operating Environment : 5 ~℉ 149 ℉(-15℃ ~ +65℃), 10~90% RH Overall Size (WxHxD) : SR10 1.82"x4.81"x0.87"(46x122x23mm) SR20 3.00"x4.89"x0.87"(76x124x23.5mm) Weight (SR10 / SR20) : 0.33lb(150g) / 0.35(160g)
PROXIMITY READER IDTECK -5- 20031125 6. Installation 6-1. Mullion/Wall Mount Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical and drill one 1/2" hole for the reader cable 1.7"(4.31cm) apart from the top hole. (If you have installed electric gang box then skip this step.) 6-2. Put reader cable into the center hole and install the reader module by using two 6-32 or M3 screws. 6-3. Put bezel into the reader module then push bezel until you hear the locking sound. 7. Wire Color Table of the SR10/20 POWER Power (DC +7V ~ +17V) DC(+) Red wire Power (Ground) GND Black wire INPUT LED Control LED_CON Yellow wire Buzzer Control Buzzer_CON Blue wire Output Format Selection 34 bit / 26 bit select 34/26_SLCT Gray wire OUTPUT (Wiegand Format) Wiegand Data-0 Data-0 Green wire Wiegand Data-1 Data-1 White wire OUTPUT (RS232 Format) RS232C TX Violet wire
PROXIMITY READER IDTECK -6- 20031125 8. Output Format 8-1. Wiegand Output Format Data format (34-bit /26-bit) Bit 1 / Bit 1 : Even parity from Bit 2 to Bit 17/ Bit 2 to Bit 13 Bit 2 to Bit33 / Bit 2 to Bit25 : 4-byte ID number / 3-byte ID number Bit 34 / Bit 26 : Odd parity from Bit 18 to Bit 33/ Bit 14 to Bit 25 Timing diagram 8.2 RS-232C(Optional) Data format START(0x02H) DATA(10 or 8 char’s) END(0x03H) LRC Baud rate : 9600 DATA : 10 characters for 4-byte output, 8 characters for 3-byte. LRC : The value made from XORing every byte from ‘START’ through ‘END’
PROXIMITY READER IDTECK -7- 20031125 9. Wire Connection to Controller The brown and the orange wire MUST be left unconnected. The violet wire is reserved for RS-232C output. Please be careful connecting the wires not to make a misconnection. 10. Operation 10-1. Apply power and you can see the red LED is on indicating the reader is on standby. 10-2. Present a proximity card to the reader until you hear a beep sound and the LED changes the color to Green simultaneously and the reader sends the RF card data to the controller then the LED changes the color to Red again for next reading. 10-3. LED Control; To change the LED colors, you may connect the LED Control Input(Yellow wire) to the power ground then the Green LED is on. Present a proximity card then the LED changes the color to Red simultaneously then Green again for next reading. 10-4. Buzzer Control; When the reader reads proximity card, only one beep sound generates in normal operating mode but you can generate more beep sounds to distinguish whether the access is granted or denied. To generate more beeps, you may control the Buzzer Control Input(Blue wire) to the power ground then you can turn the beeper on while you hold Buzzer Control Input to the power ground. 10-5. 4-byte(34bit) / 3-byte(26bit) selection: The reader outputs the serial number of a card which is a 4-byte number. It is, however, possible to make the reader send only 3 bytes of it with the most significant byte trimmed off. It is useful when there are controllers which deal with 3-byte data only as most of existing controllers are. For 3-byte outputs, connect the 34-bit / 26-bit selection input(Gray wire) to Ground. Caution : It is unavoidable that some card numbers are duplicated in 3-byte output.
PROXIMITY READER IDTECK -8- 20031125 11. FCC REGISTRATION INFORMATION FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the manufacturer for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interface, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the radio or television off and on, the user is encouraged to try to correct interference by one or more of the following measures. 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on another circuit. 4. Consult the dealer or an experienced radio/TV technician for help.
PROXIMITY READER IDTECK -9- 20031125 12. Warranty and Service STAR SR10/SR20 Philips Mifare™ Compatible Proximity Reader warranty is valid for 2 years from the shipping date. The following warranty and service information applies only to the United States of America and Republic of Korea. For the information in other countries, please contact your local distributor or suppliers. To obtain in or out of warranty service, please prepay shipment and return the unit to the facility listed below. IN THE UNITED STATES RF LOGICS Inc. Service Center 3026 Scott Blvd., SANTA CLARA, CA95054 Tel. : (408) 980-0001 Fax. : (408) 980-8060 E-mail: rflogics@rflogics.com Web-site: www.rflogics.com OUTSIDE OF THE UNITED STATES ID TECK CO., LTD. Service Center 5F Ace Techno Tower Bldg., 684-1 Deungchon-dong, Gangseo-gu, SEOUL 157-030, KOREA Tel. : +82 2 2659-0055 Fax. : +82 2 2659-0086 E-mail: webmaster@idteck.com Web-site: www.idteck.com Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to prevent damage, include the following information: 1. A proof-of-purchase indicating model number and date of purchase. 2. Bill-to address 3. Ship-to address 4. Number and description of units shipped. 5. Name and telephone number of person to contact. 6. Reason for return and description of the problem. NOTE: Damage occurring during shipment is deemed the responsibility of the carrier, and claims should be made directly to the carrier.
PROXIMITY READER IDTECK -10- 20031125 13. RMA Request Form & A/S Request Form • RMA REQUEST FORM : ORIGINAL 5F, Ace Techno Tower B/D, 684-1, Deungchon Dong, Gangsuh Gu, Seoul, 157-030, Korea TEL : +82-2-2659-0055, FAX ; +82-2-2659-0086, www.idteck.com RMA REQUEST FORM RMA No. & Date : Original Invoice No. & Date : Send To RMA Control Center 5F, Ace Techno Tower B/D 684-1, Deungchon-Dong, Gangsuh-Gu Seoul, 157-030, Korea Sales Person In Charge Requested From : Shipping Port : Air / Vessel : Departure Date : NO Model Serial Number Error Check Box by shipper RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 1 Engineer Comment Others □ : RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 2 Engineer Comment Others □ : RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 3 Engineer Comment Others □ : RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 4 Engineer Comment Others □ : RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 5 Engineer Comment Others □ : Manufacture’s Verification Product Defective : User’s Misuse : Communication Error : Installation Error : Connection Error : Others : Packing Details Dimension(L:W:H) : No. of Units Net & Gross Weight : No. of Boxes Requested By Received By Buyer’s Signature IDTECK’s Signature
PROXIMITY READER IDTECK -11- 20031125 • RMA REQUEST FORM : SAMPLE 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangsuh-Gu, Seoul, 157-030, Korea TEL : +82-2-2659-0055, FAX ; +82-2-2659-0086, www.idteck.com RMA REQUEST FORM RMA No. & Date : We send this No. , when you want. Original Invoice No. & Date : 00-00-0-000 / 1990.01.01 Send To RMA Control Center 5F, Ace Techno Tower B/D 684-1, Deungchon-Dong, Gangsuh-Gu Seoul, 157-030, Korea Sales Person In Charge Karina Kwak Requested From : Mr. Luis Castro ABC Company,… address…. Tokyo, Japan Shipping Port : Narita Air / Vessel : Air Departure Date : 2003, 11. 25 NO Model Serial Number Error Check Box by shipper SR 10 XXXXXXXXXXXXX RS 232 Com. □ Input/Output □ Power ▣ Keypad □ Card Reading ▣ RS 422 Com □ 1 Engineer Comment Write problem to be detailed. Others □ : others RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 2 Engineer Comment Others □ : RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 3 Engineer Comment Others □ : RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 4 Engineer Comment Others □ : RS 232 Com. □ Input/Output □ Power □ Keypad □ Card Reading □ RS 422 Com □ 5 Engineer Comment Others □ : Manufacture’s Verification Product Defective : User’s Misuse : Communication Error : Installation Error : Connection Error : Others : Packing Details Dimension(L:W:H) : 30 * 25 * 80 No. of Units 20 Net & Gross Weight : 150g No. of Boxes 2 Requested By Received By Luis Castro Buyer’s Signature IDTECK’s Signature
PROXIMITY READER IDTECK -12- 20031125 • A/S REQUEST FORM : ORIGINAL
PROXIMITY READER IDTECK -13- 20031125 • A/S REQUEST FORM : SAMPLE
PROXIMITY READER IDTECK -14- 20031125 MEMO
PROXIMITY READER IDTECK -15- 20031125 MEMO
PROXIMITY READER The specification contained in this manual are subject to change without notice at any time. 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangsuh-Gu, Seoul, 157-030, Korea Tel : (82) 2 2659-0055 Fax : (82) 2 2659-0086 E-mail : webmaster@idteck.com NOV. 2003 Copyright ©2003 IDTECK Co., Ltd.

Navigation menu