IDP SMART-30S Card Printer User Manual

IDP Corp., Ltd. Card Printer

User Manual

YCopyright NoticeUsers must respect the copyright laws applicable in their country. This manual must not bephotocopied, translated, reproduced or transmitted in whole or in part for any reason and bythe means that might be, albeit electronic or mechanical, without the express, writtenauthorization of the company IDP card printer.All information contained herein may be subject to modification without prior notice.IDP card printer accepts no liability for any possible errors herein, nor for any accidentaldamage or damage caused through the dissemination or the use of this manual.TrademarksSMART-50 is a trademark and IDP is a registered trademark of IDP card printer. Windows isregistered trademarks of Microsoft Corp. All other trademarks or registered trademarks aremarks of their respective holders. SMART-50 Design is a trademark of IDP.Return Materials AuthorizationIn order to make a warranty claim you must contact an IDP Reseller. You will be responsiblefor packaging the printer for shipment and the costs of shipping and insurance of the printerfrom the point of use of the printer to the IDP Reseller. The IDP Reseller will bear the costs ofshipping and insuring the printer from the repair location to the address from which the printerwas shipped.Before returning any equipment for in-warranty or out-of warranty repair, contact an IDPReseller or an IDP Service Center for a Return Materials Authorization (RMA) number.Repack the equipment in the original packing material and mark the RMA number clearly onthe outside of the box. For more information about RMA or IDP warranty statements, refer tothe Warranty booklet on the quick install guide.

$ZTable of Contents1. IntroductionUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^1.1 Printer outside features UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^1.1.1 SMART-30 outside feature. UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^1.1.2 SMART-50 outside feature. UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _1.2 Printer inside featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XW1.2.1 SMART-30 inside feature.UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XW1.2.2 SMART-50 inside feature.UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XX1.3 Ribbon cartridge featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XY1.4 LCD panel display & button operationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XZ2. Printer installationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X^2.1. Fitting the ribbonUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X^2.2. Loading the cardsUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YW2.3. The withdrawal of printed cards. UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YY2.4. Driver installation (Windows XP, 2000, 2003)UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YZ2.5. Driver installation (Windows Vista, 7, 8)UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZW2.5. Network configurationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z]3. Driver configuration UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [\3.1. Checking printer propertiesUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [\3.2. Changing printer properties UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [\3.3. Other settingsUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \W4. Utilities UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \Z4.1. Card Printer SetupUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \Z4.2. Card Printer Test UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]Z4.3. Firmware upgrade UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]`5. Optional device driver installationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^Y5.1. Contact smartcard readerUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^Y6. TroubleshootingUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^^6.1. Cleaning the printerUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^^6.2 TPH (Thermal Print Head) replacement UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _X6.3. Card movement UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _Y6.4. Printing quality UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _Z6.5. Magnetic stripe encoding UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _[6.6. General operationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _[7. Printer specificationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _]$

$[Table of PicturesPic.1 SMART-30 front featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^Pic.2 SMART-30backfeaturesUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^Pic.3 SMART-50 front featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _Pic.4 SMART-50 rear featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _Pic.5 SMART-50SUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU `Pic.6 SMART-50DUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU `Pic.7 SMART-50LUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU `Pic.8 SMART-30 Inside featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XWPic.9 SMART-50 Inside featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XXPic.10 Ribbon cartridge featuresUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU XYPic.11 Top Cover openUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X^Pic.12 Take out the ribbon cartridgeUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X^Pic.13 Loading the ribbon 1UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X_Pic.14 Loading the ribbon 2UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X_Pic.15 Installing the cleaning roller UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X_Pic.16 Peeling the protective wrapperUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X_Pic.17 Installing the ribbon cartridgeUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X`Pic.18 Close Top Cover UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU X`Pic.19 Adjusting the card thickness lever UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YWPic.20 Preparing the card 1 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YWPic.21 Preparing the card 2 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YWPic.22 Loading the cards 1 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YXPic.23 Loading the cards 2 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YXPic.24 Loading the cards 3 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YXPic.25 Loading the cards 4 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YXPic.25 SMART-30 Stacker UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YYPic.25 SMART-50 Stacker UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YYPic.26 Install XP printer driver 1 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YZPic.27 Install XP printer driver 2 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YZPic.28 Install XP printer driver 3 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YZPic.29 Install XP print driver 4 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU YZPic.30 Install XP print driver 5 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y[Pic.31 Install XP print driver 6 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y[Pic.32 Install XP printer driver 7 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y[Pic.33 Install XP printer driver 8 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y[Pic.34 Install XP printer driver 9 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y\Pic.35 Install XP printer driver 10 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y\Pic.36 Install XP printer driver 11 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y\Pic.37 Install XP printer driver 12 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y]Pic.38 Install XP printer driver 13 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y]Pic.39 Install XP printer driver 14 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y]Pic.40 Install XP printer driver 15 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y]Pic.41 Install XP printer driver 16 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y^Pic.42 Install XP printer driver 17 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y^Pic.43 Install XP printer driver 18 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y^Pic.44 Install XP printer driver 19 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y_Pic.45 Install XP printer driver 20 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y_Pic.46 Install XP printer driver 21 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y_Pic.47 Install XP printer driver 22 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y_Pic.48 Install XP printer driver 23 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y`$

$\Pic.49 Install XP printer driver 24 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y`Pic.50 Install XP printer driver 25 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Y`Pic.51 Install Win7 driver 1 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZWPic.52 Install Win7 driver 2 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZWPic.53 Install Win7 driver 3 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZWPic.54 Install Win7 driver 4 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZWPic.55 Install Win7 driver 5 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZXPic.56 Install Win7 driver 6 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZXPic.57 Install Win7 driver 7 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZXPic.58 Install Win7 driver 8 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZXPic.59 Install Win7 driver 9 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZYPic.60 Install Win7 driver 10 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZYPic.61 Install Win7 driver 11 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZYPic.62 Install Win7 driver 12 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZYPic.63 Install Win7 driver 13 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZZPic.64 Install Win7 driver 14 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZZPic.65 Install Win7 driver 15 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ZZPic.66 Install Win7 driver 16 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z[Pic.67 Install Win7 driver 17 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z[Pic.68 Install Win7 driver 18 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z[Pic.69 Install Win7 driver 19 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z[Pic.70 Install Win7 driver 20 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z\Pic.71 Install Win7 driver 21 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z\Pic.72 Install Win7 driver 22 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z\Pic.73 Install Win7 driver 23 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z\Pic.74 Rear view of SMART-50 printer 1 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z]Pic.75 Rear view of SMART-50 printer 2 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z]Pic.76 Running the NetAdmin UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z^Pic.77 Network printer is not foundUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z^Pic.78 Connecting to USB portUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z_Pic.79 NetAdmin Log-inUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z_Pic.80 Dynamic IP configuration UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z`Pic.81 Static IP configuration UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU Z`Pic.82 Network service configurationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [WPic.83 OCP configuration UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [WPic.84 Network user configuration UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [XPic.85 USB port state UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [XPic.86 Rebooting the network moduleUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [YPic.87 Reset to defaultUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [YPic.88 Upgrading the firmware 1 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [ZPic.89 Upgrading the firmware 2 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [ZPic.90 Upgrading the firmware 3 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [[Pic.91 Printer properties 1UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [\Pic.92 Printer properties 2UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [\Pic.93 LayoutUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU []Pic.94 Advanced Setup UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [^Pic.95 Paper / Ribbon / PrintingUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [_Pic.96 Side / Media UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [`Pic.97 Laminator UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU [`Pic.98 Printer sharingUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \WPic.99 Ports UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \WPic.100 AdvancedUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \XPic.101 Color ManagementUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \XPic.102 ServiceUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \XPic.103 LaminatorUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \Y$

$]Pic.104 CardPrinterSetup Log-inUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \ZPic.105 CardPrinterSetup startUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \ZPic.106 CardPrinterSetup – Card Printer Basic Setup UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \[Pic.107 SMART-30 R density UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \\Pic.108 Color density UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \]Pic.109 Resin Black density UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \]Pic.110 Overlay density UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \]Pic.111 CardPrinterSetup – Card Printer Advanced SetupUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU \_Pic.112 CardPrinterSetup – Laminator Basic Setup UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]WPic.113 CardPrinterSetup – Laminator Advanced SetupUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]XPic.114 CardPrinterTestUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]ZPic.115 Magnetic stripe encodingUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]\Pic.116 Contact smartcard encodingUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]]Pic.117 Contactless smartcard encoding UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]^Pic.118 Upgrading printer firmwareUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ]`Pic.119 Ready for firm-ware upgradeUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^WPic.120 Firm-ware manual upgrade UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^WPic.121 Ready for laminator firm-ware upgrade UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^XPic.122 Firm-ware manual upgrade UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^XPic.123 Contact smartcard reader driver installation UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^YPic.124 License agreementUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^ZPic.125 Installing the contact smartcard reader driver UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^ZPic.126 Completing the smartcard reader driver installationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^[Pic.127 Found New Hardware WizardUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^\Pic.128 Installation method selectionUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^\Pic.129 Driver location UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^]Pic.130 Completing the driver installationUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^]Pic.131 Exclusive cleaning card for SMART-50 printerUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^^Pic.132 Printer cleaning start UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^^Pic.133 Printer cleaning Step 1UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^_Pic.134 Printer cleaning Step 2UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^_Pic.135 Printer cleaning Step 3UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^`Pic.136 Printer cleaning Step 4UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU ^`Pic.137 Printer cleaning Step 5UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _WPic.138 Printer cleaning Step 6UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _WPic.139 Thermal Print Head UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _XPic.140 Print head setupUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _XPic.141 Print head replacementUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _YPic.142 Print head angleUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _YPic.142 Printing quality trouble 1 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _ZPic.143 Printing quality trouble 2 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _ZPic.144 Printing quality trouble 3 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _ZPic.145 Printing quality trouble 4 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _[Pic.146 Printing quality trouble 5 UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _[Pic.148 Printer Specification 1UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _]Pic.149 Printer Specification 2UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU _^Pic.150 Printer Specification 3UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU __$

^1. Introduction1.1 Printer outside features1.1.1 SMART-30 outside feature.For the user’s convenience, SMART-30 status can be seen through LED and the printer can becontrolled by a button. It takes a power via the 24V adaptor provided with the printer. Using USBand Network port, it is communicated with the user’s PCThe following shows the outside functional features found on the printer.¢£¤¥¦ྙTop cover open buttonྚExternal contactlessSmartcard encodingpositionྛInput hopperྜLED buttonsྜྷDividing StackerPic.1 SMART-30 front features§¨©ªྙBackside card outletྚPower switchྛ24V power connectorྜNetwork portIn case there is nonetwork option, it isclosed.ྜྷUSB port«Pic.2 SMART-30 back features

_1.1.2 SMART-50 outside feature.For the user’s convenience, SMART-50 status can be seen through LCD with LED and the printercan be controlled by two LED buttons. It takes a power via the 24V adaptor provided with theprinter. Using USB and Network port, it is communicated with the user’s PCThe following shows the outside functional features found on the printer.Pic.3 SMART-50 front featuresPic.4 SMART-50 rear features¢£¤¥¦§¨ྙTop cover open buttonྚExternal contactlessSmartcard encodingpositionྛFanྜInput hopperྜྷLED buttonsྞLCD show the processstatusྟInternal SIM reader©ª«¬ྞBackside card outletྟPower switchྠ24V power connectorྡNetwork portIn case there is nonetwork option, it isclosed.ྡྷUSB port

`There are five models in SMART-50 card printer series such as SMART-50S, SMART-50D, SMART-50L.SMART-50S (Pic.5) is the standard card printer. It can be printed in single side with the encoding. Thismanual is prepared based on SMART-50S.SMART-50D (Pic.6) have a flipper which can enable to print in both side. SMART-50D can print the bothside of the card with the encoding.SMART-50L (Pic.7) produces long-life cards for ID and access control with customizable security featuresand ability to print smart cards. To cater to expanding requirement in card security, SMART-50L’sDLW(Direct to Laminating in a Wink) technology provides the most stable & fast laminating solutions.Pic.5 SMART-50S Pic.6 SMART-50DPic.7 SMART-50L

XW1.2 Printer inside features1.2.1 SMART-30 inside feature.In SMART-30 printer, the ribbon is installed by a ribbon cartridge which can be usedsemipermanently. The following shows the inside functional features found on your SMART-30printer.Pic.8 SMART-30 Inside featuresྙOutput hopper(Stacker)Collect the printed card and/or encoded cards.ྚInput hopperLoad the cards for printing.ྛCard thickness control leverAdjust the cards thickness.ྜRibbon cartridgeInstall the ribbon and the disposable cleaning roller.ྜྷThermal Print HeadThis enables the cards to be printed.(Caution!: This is very hot after printing. Do not contact the surface of the Thermal Print Headwith fingers or a sharp metal object to avoid degrading print quality or damaging printer headpermanently.)¢£¤¥¦

XX1.2.2 SMART-50 inside feature.In SMART-50 printer, the ribbon is installed by a ribbon cartridge which can be usedsemipermanently. The following shows the inside functional features found on your SMART-50printer.Pic.9 SMART-50 Inside featuresྚOutput hopper(Stacker)Collect the printed card and/or encoded cards.ྚInput hopperLoad the cards for printing.ྛCard thickness control leverAdjust the cards thickness.ྜRibbon cartridgeInstall the ribbon and the disposable cleaning roller.ྜྷThermal Print HeadThis enables the cards to be printed.(Caution!: This is very hot after printing. Do not contact the surface of the Thermal Print Headwith fingers or a sharp metal object to avoid degrading print quality or damaging printer headpermanently.)ྞExternal contactless encoderContactless smartcard encoder.¢£¤¥¦§ྙOutput hopperྚInput hopperྛCard thicknesscontrol leverྜRibbon cartridgeྜྷThermal Print HeadྞExternal contactlessencoder

XY1.3 Ribbon cartridge featuresPic.10 Ribbon cartridge featuresྙRibbon cartridge-. Install a ribbon and a disposable cleaning roller provided with the ribbon.-. In the case of SMART-30 R model, a ribbon is not used, and a disposable cleaningroller is only installed and used.-. This semi-permanent ribbon cartridge is a component of the printer. Printer does not operateif it is broken or damaged. In this case, please contact printer reseller.ྚ ྛ Take up & Supply parts-. Ribbon is wrapped to the supply parts as the Pic. 10. It should be installed as the Pic.10.ྜDisposable cleaning roller-. It removes dust on the surface of card to improve print quality before the card is printed.It should be changed together with the ribbon.-. After installing the disposable cleaning roller to the ribbon cartridge, peel off the protectivefilm.-. It is provided with the ribbon.-. In the case of SMART-30 R model, you have to purchase the disposable cleaning rollerfrom the reseller.¢£¤¥ྙRibbon cartridgeྚTake up partsྛSupply partsྜDisposable cleaningroller

XZ1.4 LCD panel display & button operationSMART-50 printer can show the real-time process status to user. SMART-30’s status is displayed in windows tray.No LCD Display LED Button State DescriptionLeft Right Left Right1Ver X.XX…Initialize… On On Initializing Initializing with the indication of SMART-50 firmware version2INIT Error xx<Replay Replay> Blinking Blinking Repeat Repeat Error during initializing Showing error no. in case of failure of normal initializing whileSMART-50 is initialized. (Refer to page13). Press any keys for re-initializing process.3SmartAuto Ribbon Set On On Automatic ribbon setting It optimizes the ribbon position setting automatically in case of thereplacement of color ribbon(YMCKO or YMCKOK).4Auto Ribbon SetFail!!!! Blinking Blinking Fail to optimize theribbon setting Display these messages when the auto ribbon setting is failed andit shows the ribbon detecting level.5Auto Ribbon SetColor=xxx(xxx) Blinking BlinkingFail to optimize theribbon setting anddisplay the ribbon’s colorvalue6SMARTSystem Ready On On InstalledribboninformationSoft powerON/OFF StandbyPrinter is ready for printing and you can check the installed ribboninformation by pressing the left button. Printer turns off by pressingthe right button. Printer turns on by pressing the right button when itturns off.7Wait.. 1”CTemperature=xxx Blinking BlinkingPrinter’s operatingtemperature is under1୅Shown it when printer’s operating temperature falls down under1୅. Normal operating temperature is 15୅~35୅.8SmartUnlock Please.. On On Printer is locked Physical key option is active using the CardPrinterSetup utility andit shows the locked state. Unable to print.9SmartVerify your PC On On PC is not authenticated Authentication option is active using the CardPrinterSetup utility.When use the printer with an unauthenticated PC, it is shown.Printer is not working.10 Ribbon BalanceType / Remains On On Card out Display the ribbon typeand remains Display the installed ribbon’s type and the remains. It can be shownby pressing the left LED button on the system ready mode.11 SMARTPrinting! On On Printing Under printing.

X[No LCD Display LED Button State DescriptionLeft Right Left Right12 SMARTMag R/W On On Reading or writing theMagnetic stripe Magnetic encoder is reading or writing the magnetic stripeinformation.13 Spool Error!<-Any Key Push-> Blinking Blinking Cancel &Initialize Cancel &Initialize Printingdataisnottransmitted properly Shown it when error occurs in a printing data transmission. Pressany keys to delete the spooled data and to return the ready state.14 Print Error xx<Replay Cancel> Blinking Blinking Repeat Cancel &Initialize Error in printing ormoving a card Error in the printing or the transmission. Retry by pressing the leftbutton or cancel the command by pressing the right button.15 Top Cover Open<-Card Moving -> Blinking Blinking Move acard to theback sideMoveacardto the frontside Top cover openTop cover is open. The card in the printer can be moved bypressing the left or right LED button. If press both buttons at thesame time, the print head will be up and down. (Flipper will be flipover if it is installed)16 Check Please..Ribbon Not Found Blinking Blinking Ribbonredetecting Ribbonredetecting There is no ribbon in theprinter or fail to detectFail to detect the ribbon. Check the ribbon installed state. If thereis no ribbon, install the ribbon. If there is a ribbon, pull out it andinstall again. Press the left or right button to redetect the ribbon.17 Check Please..Ribbon Zero Blinking Blinking Ribbonredetecting Ribbonredetecting The installed ribbon hasrun outIt is displayed when the installed ribbon is all used up. Replacewith new ribbon. Press the left or right button to redetect theribbon.18 Check Please..TPH Not Found Blinking Blinking Thermal Print head is notinstalledThermal Print Head is not installed or there is a misconnection ofthe cable. Open the top cover to check the print head installedstate or turn off the printer and check the cable connecting state.19 Print Error xxTop Cover Open Blinking Blinking Fail to move the card out(Check the card in theprinter)The card in the printer will be come out when the initialization ortop cover close. If it is not come out, this message will bedisplayed. Remove the card and close the top cover.20 Card Out Error<Replay Cancel> Blinking Blinking Repeat Cancel &InitializeFail to move the card out(Check the card in theprinter)After an error occurs in printing, the error card is not come outeven though "Replay" or "Cancel" button is pressed.21 SMARTDownload... On On Firmware downloading The printer is downloading the firmware. Do not turn off the poweruntil it is rebooting. It takes about 20 seconds.22 Board Test ModeWait Test mode state Test mode which can test the sensors or motors of the printer.User can set the LED status.Table1 Status display

$X\Description of printer error codeError code Description0Card in error1Card move center error2Card out error3Card move magnetic error4Card move contact encoder error5Card move contactless encoder error6Card move error from the printer to the flipper7Card move error form the flipper to the printer8Print head up error9Print head down error10 IC Contactor up11 IC Contactor down12 Flipper top error13 Flipper bottom error14 Error in printing15 Magnetic stripe read/write error16 Ribbon search error17 Ribbon move error18 No print head installed19 Print head overheating20 No ribbon21 Printing data error22 Card back out error23 Magnetic data erasing error24 Printer password is not correct25 Magnetic stripe track 1 read error26 Magnetic stripe track 2 read error27 Magnetic stripe track 3 read error28 Printer locked state29 Printer spool full state30 No defined31 No defined$

X]Description of laminator error codeError code Description0Laminator head up error2Laminator head down error4Laminator card in error6Laminator card move error8Laminator card front out error9Laminator card rear out error10 Flipper error13 Error while laminating15 Laminator initializing error16 Laminator film zero error17 Laminator film search error31 No laminating film

X^2. Printer installation2.1. Fitting the ribbonBefore printing, prepare the related items such as a card, a ribbon and a cleaning roller. In thissection we invite you to know the proper method of installing the ribbon and the cleaning rollerinto the printer. In the case of SMRT RW model, the ribbon is no needed so skip 2.1.4 and2.1.5 process.2.1.1. Turn off the printerPic.11 Top Cover open2.1.2. Open the printer top cover bypressing the top cover openbutton.Pic.12 Take out the ribbon cartridge2.1.3. Take out the ribbon cartridge.

X_Pic.13 Loading the ribbon 12.1.4.Install aribbon into the ribboncartridge as left Pic. 13.Pic.14 Loading the ribbon 22.1.5. Insert the supply side of the ribbonto no.1 hole and press the opposite(no.2). Insert the take-up side of theribbon same method to no.3 andno.4. After inserting, tighten theribbon.(Caution! If the ribbon is not tightened, arolling up error might be happened.)Pic.15 Installing the cleaning roller2.1.6. Install the disposable cleaningroller to the ribbon cartridge.Pic.16 Peeling the protective wrapper2.1.7. Peel the protective wrapper fromthe cleaning roller.After removing the protective wrapper, thecleaning roller should be kept clean fromfingerprints, dust and foreign substances toavoid contamination because it is adhesive.(Caution! Do not use without peeling off theprotective wrapper because the cleaningroller cannot perform its function.)ཛཛྷཝཞ

X`Pic.17 Installing the ribbon cartridge2.1.8. Install the ribbon cartridge into theprinter after installing the ribbonwith a cleaning roller to thecartridge.Pic.18 Close Top Cover2.1.9. Close the top cover(If it is not closed properly, check the installationstate of the ribbon cartridge.)

YW2.2. Loading the cardsThis section shows how to load the plastic cards.Pic.19 Adjusting the card thickness lever2.2.1. Open the input hoppercover.2.2.2. Adjust the card thickness with thecard thickness control lever.(Caution! If the adjustment is not correct, it willmake some error. Use the type of cards in thespecification of this manual. Always keep thecard surface clean state.)Pic.20 Preparing the card 1Pic.21 Preparing the card 22.2.4. To separate cards from each other,push a stack of cards back andforth to an angle about 45 degreesvertically.(Static charge makes cards stuck withsignificant adhesive force. These cards must bephysically separated from each other beforeinserted into the feeder. If not separated,feeding or printing problems may occur.)

YXPic.22 Loading the cards 12.2.5. Stand the stack of cards verticallyafter separating.Pic.23 Loading the cards 22.2.6. Load the cards on the input hopperproperly and close the hoppercover.Pic.24 Loading the cards 32.2.7. When insert each one card, insertthe card to the end as the Pic. 24and 25.Pic.25 Loading the cards 4

YY2.3. The withdrawal of printed cards.Printed cards are passed out to the stacker of rear bottom side of SMART printer. SMART-30’s stackercan be divided as following image.Pic.26 SMART-30 StackerSMART-50’s stacker sticks out of the device so you can withdraw the printedcards easily.Pic.27 SMART-50 Stacker

YZ2.4. Driver installation (Windows XP, 2000, 2003)Pic.28 Install XP printer driver 12.4.1. Insert the installation CD providedwith the printer.2.4.2. Choose the language and click“Driver Install”.Pic.29 Install XP printer driver 2Pic.30 Install XP printer driver 32.4.3.STEP 1:If the printer is connected to the PCand turned on, turn off the power ofthe printer.Click “Next”. The existing installedprinter driver will be removed.If the printer driver is already installed, it willbe removed automatically but it may taketimes.Choose the language as shown on the Pic.29and 27.Pic.31 Install XP print driver 4

Y[Pic.32 Install XP print driver 52.4.4.STEP 2:Click “Next” to ready theinstallation of the printer driver.Pic.33 Install XP print driver 62.4.5. If there is a pop-up window for thesoftware installation, click“Continue Anyway”.Pic.34 Install XP printer driver 72.4.6. STEP 3:Click “Next” to use USB port.Click “TCP/IP Network port” to usethe printer as network printer andchoose the printer as shown on thePic.34.(If there is no information on the window forthe network printer list, it means that theprinter is not connected to the network. Check“2.5 Network Printer” section.)Pic.35 Install XP printer driver 8

$Y\Pic.36 Install XP printer driver 92.4.7. Please connect a power supplytothe printer.(For the network printer, refer to “2.5 NetworkPrinter” section.)Pic.37 Install XP printer driver 102.4.8.Please connect USB cable providedwith the printer to PC and theprinter.(For the network printer, refer to “2.5 NetworkPrinter” section.)Pic.38 Install XP printer driver 112.4.9. Turn on the printer to boot up it.$

Y]Pic.39 Install XP printer driver 122.4.10.Select“Install the softwareautomatically (Recommended)”andclick “Next”.Pic.40 Install XP printer driver 132.4.11. Click “Continue Anyway” inSoftware Installation window.Pic.41 Install XP printer driver 142.4.12. Click “Finish” in Completing theFound New Hardware Wizardwindow.Pic.42 Install XP printer driver 152.4.13.When the printer driver installationis completed. Click “Close”.

Y^Pic.43 Install XP printer driver 162.4.14.Check “IDP SMART-50 CardPrinter” is generated in Printersand Faxes window.Pic.44 Install XP printer driver 172.4.15. After selecting the icon of “IDPSMART-50 Card Printer”, click theright mouse button and select the“Properties”.Pic.45 Install XP printer driver 182.4.16.Select “General” tap and click“Print Test Page” button on the IDPSMART-50 Card Printer Propertieswindow.

Y_Pic.46 Install XP printer driver 192.4.17. Printer will start the printing andthere will be the window which asksthe printing success. If the printingis normal, click the “OK”(If the printing is abnormal or the printer erroris occurred, remove the problem refer to“Trouble Shooting” section and execute testprinting again.)Pic.47 Install XP printer driver 202.4.18. Please install “Smart Application”program after installing the printerdriver.Pic.48 Install XP printer driver 212.4.19. Click “Next” on the “SmartApplications -InstallShield Wizard”window.Pic.49 Install XP printer driver 222.4.20. Select “I accept the terms of thelicense agreement” and click“Next”.

Y`Pic.50 Install XP printer driver 232.4.21. Choose the destination locationand click “Next”.Pic.51 Install XP printer driver 242.4.22. Click “Install” to begin theinstallation.Pic.52 Install XP printer driver 252.4.23. Smart Design/DB program isinstalled successfully.

ZW2.5. Driver installation (Windows Vista, 7, 8)Pic.53 Install Win7 driver 12.5.1. Please insert the installation CD.2.5.2. Please choose language and click“Driver Install”.Pic.54 Install Win7 driver 22.5.3.When “User Account Control”window is opened, click “Yes”Pic.55 Install Win7 driver 3Pic.56 Install Win7 driver 42.5.4.STEP 1:Please turn off printer if it isconnected to PC. Please click“Next”.When you click “Next”, older driverwill be removed automatically.This process will take several minutes toremove older driver.You can select the languages by selecting thecombo box as shown on the Pic.55.

ZXPic.57 Install Win7 driver 5Pic.58 Install Win7 driver 62.5.5.STEP 2:When you click “Next”, the driverinstallation will be ready.Pic.59 Install Win7 driver 72.5.6. Please click “Install this driversoftware anyway” in case“Windows Security” window comesout.Pic.60 Install Win7 driver 82.5.7.STEP 3:Please click “Next” if printer isconnected to USB only.If you want to install the driver for aprinter connected to network,please select the “TCP/IP Networkport” and select the proper printeras shown on the Pic.60.(If no printer comes out on the window, pleasecheck the connection. Please refer “2.5Network Printer Setup”.)

ZYPic.61 Install Win7 driver 9Pic.62 Install Win7 driver 102.5.8. Please connect a power supply tothe printer.(If your printer is for network, please refer “2.5Network Configuration”.)Pic.63 Install Win7 driver 112.5.9. Please connect USB cable to theprinter.(If your printer is for network, please refer “2.5Network Configuration”.)Pic.64 Install Win7 driver 122.5.10. Please turn on the printer.

ZZPic.65 Install Win7 driver 132.5.11. When driver installation iscompleted, please click “Close”.Pic.66 Install Win7 driver 142.5.12. Please open “Devices andPrinters” from “Hardware andSound”. Please check if “IDPSMART-50 Card Printer” is created.Pic.67 Install Win7 driver 152.5.13. Please click the right mouse buttonafter cursor is placed on “IDPSMART-50 Card Printer” icon. Click“Printer properties”.

Z[Pic.68 Install Win7 driver 162.5.14. Please select“general” tab andclick “Printer test page” in “IDPSMART-50 Card Printer Properties”window.Pic.69 Install Win7 driver 172.5.15. Please check test card if it isprinted properly and click “Close” ifa card is printed properly.(If card is not printed or error comes out,please refer “Trouble Shooting”.)Pic.70 Install Win7 driver 182.5.16. Please install “Smart Design/DB”by clicking “Smart Design/DBInstallation”.Pic.71 Install Win7 driver 192.5.17. Please click “Next” when “SmartApplication Install Shield Wizard”comes out.

$Z\Pic.72 Install Win7 driver 202.5.18. Please agree “Iaccept the terms ofthe license agreement” and click“Next”.Pic.73 Install Win7 driver 212.5.19. Please select directory forprogram installation and click“Next”.Pic.74 Install Win7 driver 222.5.20. Please click “Installation”.Pic.75 Install Win7 driver 232.5.21. Please click “Finish”.$

Z]2.5. Network configuration2.5.1 Connecting network portPic.76 Rear view of SMART-50 printer 1The printer which installed withnetwork option has a port for networkconnection as shown in the Pic.76 - ྛ.ྙPower SwitchྚPower Supply ConnectorྛNetwork PortྜUSB PortPic.77 Rear view of SMART-50 printer 2Please connect networkcable (RJ45)to a printer.(Network cable is not supplied. Please asknetwork administrator for more questions.)¢£¤¥

Z^2.5.2 Network configurationDHCP (Dynamic Host Configuration Protocol) which automatically assigns IP address to the SMART-50network printer on the same network is default for IP configuration. If you don’t have DHCP server, youneed to set static IP.Please run NetAdmin.exe in the SMART-50 installation CD to set or change network configuration.Pic.78 Running the NetAdminNetAdmin is run as the Pic74 afterturning on SMART-50 network printer.ྙPrinter Connection StatusSearches local network, finds and showsavailable network printer.ྚNetwork Module ManagementSearches connected encoder on networkmodule. Reboots, Resets network module.Firmware upgrade availableྛPrinter ConfigurationSets detailed system configuration.ྜNetwork InformationShows firmware version of network modulePic.79 Network printer is not foundWhen no printer is connected tonetwork, there is no printer shown onthe box.Please click “Refresh”. If no printer shown, pleasecheck as below,1. Please check the printer is turned on.2. Please check network cable is connected tonetwork hub and works properly (LED lampblinking).3. Please check if there is DHCP server in thelocal network. When DHCP server is not inyour local network, you need to set Static IP.4. If Static IP is used, please check the IPconfiguration. If another device uses same IPaddress, it doesn't work.¤¥£¢

Z_Pic.80 Connecting to USB portIf you are unable to find printer in localnetwork, please connect printer byUSB. You can setup network by USB.When you click Refresh, you can find a printerconnected by USB as shown in the Pic.80.zYou don’t need to install device driver fornetwork configuration by USB. Please ignoremessages related to device installation.zYou can change values of “SystemManagement” only when you connect a printerby USB. Please connect a printer by network touse all of the functions of Netadmin.exe.Pic.81 NetAdmin Log-inPlease select a proper printer and click“connect”. Please enter password andclick “OK”.Default password is “admin”.

Z`Pic.82 Dynamic IP configurationIf you setup network automatically,please choose DHCP.zPlease select DHCP and click “SetConfiguration”.z“DHCP”isdefaultforSMART-50printer.zDHCP server should be in local network to useDHCP function.zStatic IP is recommended. DHCP serverassigns IP address automatically but this IPaddress is temporary, so the IP address may bechanged. In this case, the network error mayoccur in connecting to SMART-50 networkprinter.Pic.83 Static IP configurationPlease select “Static” for Static IPconfiguration.zPlease enter values for “IP”, “Network Mask”,and “Gateway”. Click “Set Configuration”.zPlease check IP address properly which doesnot conflict with other devices.zIfyouarenotawareofstaticIP,pleaseasknetwork administrator for Static IP.zWe recommend using Static IP because it ismore stable for using SMART-50 networkprinter.

[WPic.84 Network service configurationYou can change Service Configuration.zSMART-50 network printer provides 3 kinds ofservice (change “USB Spool”, “Network Spool”and “Network SDK”). You can select andchange the service according to the need.zIn “Network SDK”, you can control the printerand print a card well, and the printer supportsSSL (Secure Sockets Layer) and UserAuthentication for security.zPlease use default and ask technician fordetails.Pic.85 OCP configuration   v j w Uz{            vzzj   ˈ| vjwˉzˈ | { l ˉ         U m S  zzs  | hUzw       UU

[XPic.86 Network user configurationYou can add, change, delete User andchange its password.z“admin” is administrator and you can’t deletethis account. Please don’t forget password for“admin”z“Get User”: shows available usersz“Add User”: makes new userz“Del User”: deletes selected userz“Change Password”: changes password2.5.3 Network module managementPic.87 USB port state“USB port state” shows USB devicestatus connected on network module.zNetwork module has 4 USB ports.zNetwork module supports PC/SC. When youinstall the encoders that support PC/SC onnetwork module, you can recognize the statusof encoders.

[YPic.88 Rebooting the network module“Rebootmodule” reboots networkmodule.zPlease click “Yes” when pop-up window comesout for reboot.zIt takes 1 minute to reboot.zPlease click “Refresh” after reboot. Whenproper printer shown, please connect printer byclicking “Connect”.Pic.89 Reset to default“Reset to default” resets to default andreboot network module.zPlease click “Yes” when pop-up window comesout for reset.zIt takes 1 minute to reboot.zPlease click “Refresh” after reboot. Whenproper printer shown, please connect printer byclicking “Connect”.

[ZPic.90 Upgrading the firmware 1“Upgrade firmware” enables toupgrade firmware of network module.zYoucanchooseafirmwarefile.Pic.91 Upgrading the firmware 2zWarning box will be shown during firmwareupgrade for network module.zIt is recommended not to do other work duringfirmware upgrade for system reliability.zPlease do not turn off a printer until theupgrade is completed.

[[Pic.92 Upgrading the firmware 3zWhen firmware upgrade is completed, pop-upcomes out for reboot. Please click “Yes”.zIt takes 1 minute to reboot.zPlease click “Refresh” after reboot. Whenproper printer shown, please connect printer byclicking “Connect”.

$[\3. Driver configuration3.1. Checking printer propertiesTo check printer properties, you need to open printer driver. Please open “Driversand Printers” and right-click “IDP SMART-50 Card Printer”. Click “Properties”. ForWindows 7 or 8, please click “Printer Properties”.Pic.93 Printer properties 1When you click “Printer Properties” as likePic.88, a device driver of “IDP SMART-50Card Printer” is shown.3.2. Changing printer propertiesIn the general tab shown as Pic.94, you can check the printer model andspecifications.Pic.94 Printer properties 23.2.1. Printing PreferencesPlease click “Printing Preferences” shown on thebottom of Pic.95.There are 3 tabs of “Layout”, “Paper/Ribbon /Quality”and “Side/Media”.(You can set the options for printing shown onPic.95.)$

[]Pic.95 Layout3.2.1.1. Layout- You can select either horizontal or vertical printingdirection. To apply your selection, click “OK”.

[^Pic.96 Advanced Setup3.2.1.2. Advanced setupReset Default Values: Reset to default.Color Correction: You can correct gamma forcolors. You need to use CardPrinterSetup to adjustcolor densities.Resin Black (K) Processing: Set criteria for resinblack processing.Text: to set density criteria for extracting blackobjectsDot: to set density criteria for extracting black dotsThreshold: to set density criteria on ditheringDithering Degree: to set sharpness on ditheringExtra Controls :Edge Size: to set not printed area in case of notusing Edge-To-EdgeEject Card: tosetifejectacardafterprintingErase Density : to set erase density forSMART-30 R EraseSharpening: to calibrate image sharpenedFlip Front: to set printed direction of image onfront side.Flip Back: to set printed direction of image onback side.Magnetic Strip Encoding Method: to set magneticstripe encoding method for each trackNormal: to encode on LoCo Card forwardsReverse: to encode on LoCo Card backwardsBit: to encode on LoCo Card in BitHiCo Normal: to encode on HiCo Card forwardsHiCo Reverse: to encode on HiCo CardbackwardsHiCo Bit: to encode on HiCo Card in BitMagnetic Card Flip R/W: to set back side imageprinting when magnetic encodingManual Magnetic Stripe encoding: to put in data onmagnetic stripe manuallyNot Use: not to use magnetic stripe encodingEncoding and Printing: to print after magneticstripe encodingEncoding or Laminating only: encodingmagnetic or laminating. without printing

[_Pic.97 Paper / Ribbon / Printing3.2.1.3. Paper / Ribbon / PrintingzSupply TraySupplyPlease select “CR-80” because SMART-50 has 1 input hopper.TrayPlease select “Auto” because SMART-50 supports CR80 cards only.zRibbonRibbonIt shows the type of installed ribbon. You don’t need to select this option as SMART-50recognizes ribbon automatically with RF Tag.ResinYou can set the method to extract resin black when you use design programs. (If you useSmart Design, you don’t need to select this option.) It will be set automatically.Black Objects: to extract resin black automatically for text, line, box, circle, binary images,etc.Black Texts: to extract resin black for text onlyBlack Dots: to extract resin black for all of blackNot Use: not to extract resin blackSplitYou can set the both sides (Front:YMCO, Back:K) to save color ribbon(YMCKO, HYMCKO,BYMCKO). It is only activated while printing both sides option is set.zPrintingModeSet printing modeStandard: Default print mode. Prints all area of prinitingPartial: Partial print mode. It is printed partially for the print area only. Printing speed canbe faster than standard mode.SpeedSet printing speed and quality.Standard: Default print mode and best quality setting option of printingHigh: Fast print mode. This option can be used with only K and KO ribbo. Printing qualitymight be lower than Standard.ColorYou can select color or black&white print. (“Color” option is available only with color ribbon.)DitherThere are 3 possible selections, Threshold, Random, and Diffusion Dither. It is performedwith K and KO ribbon only. (Please select “Diffusion Dither” for high quality.)

[`Pic.98 Side / Media3.2.1.4. Side/MediaTo set printing side and printing mask.- Print SideYou can select one side printing or both sides printing(It is possible only when you have a flipper.)- Front / BackYou can use a predefined mask or user defined mask(white card, smartcard, Magnetic stripe card, etc.) onfront or back side.You can define a mask. User defined mask usesBITMAP file (1012 X 636 pixels).Blue (RGB(0,0,255)): Print and OverlayPink (RGB(255,0,255)): Print onlyBlack (RGB(0,0,0)): Print, Overlay and FlorescentPic.99 Laminator3.2.1.5. LaminatorThis tap will be created only when SMART-50L printeris connected to PC. In the case of normal SMART-50Printer, this tap will be not displayed.To set Laminator printing options.-Laminator SideYou can select not use, top side, bottom side andboth sides printing-OverlayYou can select whether overlay prints or not.Default setting is no overlay when laminating and werecommend to use the default value.-PositionYou can set Laminating start position of width and thevalues can be set from -50 to 50. The number is1/300 inch.-TemperatureYou can set Laminating temperature and the valuescanbesetfrom100୅to 180୅.-Laminating OnlyYou can skip printing and do laminating only bysetting a value inPrinter setup - Print preferences - Advanced Setup -Encoding and Laminating - Set the value as“Encoding and Laminating Only”

$\W3.3. Other settingsPic.100 Printer sharing3.3.1. SharingYou can share a printer with Sharing tab via Network.Default is “Not sharing”Pic.101 Ports3.3.2. PortsPort tab shows which port is connected with SMART-50. SMART-50 has connection with USB Virtualprinter port as Pic.101 because SMART-50 uses USBconnected to PC.(Caution! This port is selected automatically. It isrecommended to maintain default.)$

$\XPic.102 Advanced3.3.3.AdvancedIt is available for Working Time setting, Priority order,Spool print etc. in “Advanced” tab. “Advanced” settingfollows MS Windows standard. If you want to changethe setting, please refer to the Window manual.(It is recommended to maintain default.)Pic.103 Color Management3.3.4. Color ManagementIn “Color management” tab, you can select colormanagement profile fit to the printer.SMART-50 uses color profile to express optimal color.The driver selects color profile automatically to fiteach ribbon.(It is recommended to maintain default.)Pic.104 Service3.3.5. ServiceYou can recognize printer serial, printer ID, driverversion, firmware version, type of ribbon & balanceand printer’s status.You can print the “technical support sheet” on a cardto check printer’s setup value.To clean printer, please insert a cleaning card in ahopper and click “Clean Printer”. For further details,please refer “6.1. Cleaning Printer”.Please refer “4.2.6 Printer Status” for numbers of“Printer Status” and “Printer error”$

$\YPic.105 Laminator3.3.6. LaminatorThis tap will be shown only when SMART-50L printeris connected to PC. You can recognize laminatorfilm’s type, balance, laminator’s version, serialnumber status.$

$\Z4. Utilities4.1. Card Printer SetupSMART-50 is produced with optimized setting. You need to adjust setting value if required or spare partsare replaced using CardPrinterSetup in our Installation CD. You can adjust following settings withCardPrinterSetup.4.1.1. Run CardPrinterSetupPic.106 CardPrinterSetup Log-inPasswordinputwindowisdisplayedwhenyourunthis program. If you input the correct password, therecorded setup value will be shown and you canchange values. The password is saved to SMART-50printer. If you use another PC with same printer,previous password is required to run this program.(Default password is none. Please press OK if youhave not set password.)Pic.107 CardPrinterSetup startWhen you are successful to log-in, you can set valuesshown as Pic.107.$

$\[4.1.2. Card Printer4.1.2.1. Basic SetupPic.108 CardPrinterSetup – Card Printer Basic SetupྙTo show connected printersDevice: You can select a printer using pull-down menu. “IDP SMART-50 Card Printer” is aname of printer. “SMART228” is printer ID, “USB001” is connected port.ྚTo set administrator password and user password.Change Root PW: To set administrator (root) password. This password is used to verifyuser authority for CardPrinterSetup and User Authentication. Also it is required for Userpassword management. (Please set password for security use.)Change User PW: To set user password for User Authentication.ྛClick “Card Printer” tap.(If laminator is installed, you can setup laminator setting value by“Laminator” tap.ྜTo show firmware version, serial number of printer and serial number, resistor & type of printhead.ྜྷTo show print area. It shows exaggeratingly for user convenience.ᐭᐮᐯᐰᐱᐲᐳᐴᐵᐶ$

$\\ྞTo set print area. Please set it properly to print on an entire card because SMART-50 is adirect thermal card printer. When you click “ྟPrint”, a card is printed as like “ྜexample”.Please set values properly that all circles of each corner are printed and blank spaces are0.4mm ~ 0.5mm in the top and the bottom of a card. Please set values by following order.XStartPosition:Please set right and left properly by adjusting X position.YStartPosition:Please set the start position of printed example image and blank space inthe top is 0.4mm ~ 0.5mm.YEndPosition:Please set the end position of printed example image and blank space inthe bottom is 0.4mm ~ 0.5mm. It is recommended to set bigger value for “Y scale” thandefault.YScale:Please set to show circles in the bottom.ྟTo set density. SMART-50 enables to set different density for each color, resin black andoverlay. So, please set each density for high quality. Please optimize the quality byadjusting each value. To optimize, you repeatedly adjust the density and print a Calibrationcard and check the print state until you get the optimum.If your printer is SMART-30 R model, please do not install ribbon. You can set densitywith Rewritable cards. Please adjust total density only.Total Density: To set all of the density (Color, Black and Overlay) at one time.If your printer is SMART-30 R model, when the density is too strong, you will havedarker background color. (Background color may vary depending on card type.)When density is proper, texts and images are printed clearly and there is nobackground color. When density is too low, texts and images are printed dull.Pic.109 SMART-30 R densityYMC Density: To set color density. Please maximize YMC density as you can, whichenables to express range of color and vivid images. If it is too strong, green or red marksare appeared. If it is too weak, the print quality will be dull. (Please refer Pic.109.)$

$\]Pic.110 Color densityBlack Density: To set resin black density. In Pic.111, barcode is printed to express density.When density is too strong, barcode is printed too thick. When density is too weak, barcodeis too thin. Please adjust resin black density to express clear barcode. Please referfollowing pictures.Pic.111 Resin Black densityOverlay Density: To set overlay density. Please set it when overlay is printed on surfaceregularly. If it is too strong, it is hazy and marks are appeared. If it is too weak, overlay panelis not printed edge areas. You can check it with printed card under the light.Pic.112 Overlay densityྠTo print calibration card.ྡTo show advanced Setup.(It is recommended not to set advanced setup.)ྡྷTo load or save values.Get Config.: to get values from current printer$

$\^Set Config. : to set values to current printerLoad from File: to load values from fileSave to File : to save values to fileLoad Default : to load default. Please adjust values again after load default.Close : to close CardPrinterSetup$

$\_4.1.2.2. Advanced SetupYou can set more values.Pic.113 CardPrinterSetup – Card Printer Advanced SetupྙYou can set Printer ID, PC serial, Print head and Magnetic encryption key.Change Printer ID: When SMART-50 is used by SDK, you can set unique ID for SMART-50printer regardless of whether it is connected by USB or what IP address is. It is useful toconnect and use several printers. Default is “SMART-50”.Set PC Serial: One of security function. You can use a printer with specific PC.It is activated when you click “Set PC Serial” after “PC Authentication”ofྞis ticked andrebooted. At that time, the specific information of used PC is saved to SMART-50 printer.Change Head: When you replace thermal print head, you must change head information foroptimal quality. Please change head serial number, resistor and type of head in the ChangeHead Dialog window after click “Change Head”.Set Mag. Encrypt Key: One of security function. When you use SDK, you can encryptmagnetic stripe encoding data transmitted by USB. You can define and save the encryption keyto SMART-50 using “Set Mag. Encrypt Key”.ྚTo show how many cards are issued with SMART-50 printer. “Total Issue Count” is the numberof issued cards from factory shipment, “User Issue Count” is the number of issued cards fromreplacing head. When you replace a head, please initialize the number by ticking “Reset UserIssue Count”.ྛTo show color and motor management. SMART-50 recognizes ribbon color automatically andcontrols motor by ribbon remaining. “Yellow Level”, “Magenta Level”, “Cyan Level”, “Black Level”are default value for ribbon and user does not change values. “RMP+”, “RMP-“, “RMM+”, “RMM-“ are necessary variables to control ribbon motor. Please do not change values for them as itaffects card quality.ྜSMART-50D is made by attaching a flipper in SMART-50, so you need to adjust it to be tuned inthe horizontal. “Rotate Top” is a value when the card of top side is in line. “Rotate Bottom” is avaluewhencardofbottomsideisinline.Pleaseclick“AutoRotatorSet”whenerrorisoccurredduring a card moved to or from a flipper.ᐭᐮᐯᐰᐱᐲ$

$\`ྜྷPlease refer as below for other values.Reserved: Not usedWarming Up Display: If you use SMART-30 R, LED buttons are blinked during print head iswarming up. You can adjust the timing of LED blinking by adjusting values of “Warming UpDisplay”. It becomes faster as the value is smaller.Mag. Write Mode: You can order the way how to encode magnetic stripe.“L:A, H:I”: encodes 3 tracks at once for LoCo card and encodes at twice by dividing 1,3 and 2track for HiCo cards.Magnetic Space: The distance of magnetic stripe when you encode.SBS Only: Please enable it when you issue cards with software programed by SDK. This optiondisables printer device driver.Board Type: to choose they type of mainboard. Please do not change it.Security: There are several ways to set a security function for SMART-50.PC Authentication: You can use a printer with specific PC. It is activated when you click “SetPC Serial”.Physical Key: You can set this option when physical key is installed.User/Root Authentication: You can set passwords for User and Administrator.Use USB Serial: When SMART-50 is connected to USB, it transmits the USB serial number toPC. Default is the same number used by all SMART-50. Please set this option when you usemultiple SMART-50 printers connected to 1 PC via USB. It enables unique serial numbers foreach USB.Ribbon Position: To set the ribbon position on card. Please set it default.Warming Up Temp.: To control the temperature of warming up before printing. For SMART-30R,youneedtowarmupprintheadtoprinthighquality.Werecommendwarmingupto50degrees.Card Out Delay: To set timing of hopper motor for ejecting card. Please set it default.Card Out: to set the way to eject cards.Error Card Out: to set the way to eject error cards.DCL Mode: When you use SDK and print cards with DCL mode, you don’t need to install printerdevice driver.Dump Mode: It records log data.$

]W4.1.3. Laminator4.1.3.1. Basic SetupPic.114 CardPrinterSetup – Laminator Basic SetupྙThe combo box shows connected printersྚClick Laminator Tap.ྛIt shows the information of installed laminator such as firm-ware version, serial number.If you click “Change Serial No.” button, you can change serial number.ྜThe fields show laminator film’s type, balance, code and laminator code.Film Type : It shows installed film’s type and vendor code.Film Remain : It shows installed film’s total number and balance.Laminator Code : It shows Laminator’s code, vendor and local code.Film Code : It shows installed film code, vendor and local code.ྜྷYou can change the values according to the installed film type.ᐭᐮᐯᐰᐱᐲᐳ

]XHeater Temperature : It is for laminating temperature.Laminating PPS : Laminating speed.Laminating Move Pulse : The distance of laminating movement.Separation with Card : After laminating and removing film, the value changes thedistance of card movementSeparation with Film : After laminating and removing film, the value changes theDistance of film movement.Lami. Start Card Pos : The value is for laminating start position.Torque Laminating Max : Maximum torque of motor while laminating.Torque Laminating Min : Minimum torque of motor while laminating.Laminating with Pulse : The value is for change laminating width.Film Attribution : It changes film attribution.ྞIt shows “Advanced Setup” window.ྟ“Save” or “Load” the values.Get Config : Read the values from connected printer.Set Config. : Set the values to connected printer.Load from File : Load the values from saved file.Save to File : Save the values into a file.Close : Close the program.4.1.3.2. Advanced SetupPic.115 CardPrinterSetup – Laminator Advanced SetupྙIt shows total laminating count.ᐭᐮᐯ

]YྚThe values are for setting motor torque of film movement.Torque Move Max : Change Maximum motor torqueTorque Move Min : Change Minimum motor torqueྛThe values are for setting motor torque of laminating.You can set the values of each section.ྜYou can set “Head” temperature of laminating.You can set the values of each section.ྜྷRotator position

]Z4.2. Card Printer TestBasically Card Printer use standard printer device so you can be used same as general paper printer.In the case of magnetic stripe, contact, contactless encoder option, you will need to install appropriatedriver and operate individually. Encoding operation will be controlled by “CARD PRINTER SDK”. Youcan test all feature of printer by Card printer Test. Card Printer Test program is developed by using“SMART Printer SDK”4.2.1. CardPrinterTestWhen CardPrinterTest is run, all function can be tested individually.Pic.116 CardPrinterTestྙSelect Printer: select printer to test. In the Pic.116, “IDP SMART-50 Card Printer” is thePrinter name, SMART228 is the Printer ID, and USB001 is the connected port.ྚControl : To execute each step to testྛPrint: Print test with CSD file which is designed by Smart Design program.ྜBatch Start: Repeat selected encoding test by “ྜྷEncoding”ྜྷEncoding: Encode Magnetic Stripe, Contact Card, Contactless CardྞPrinter Status: Check printer status.ྟMessage: Description of status by log.ᐭᐮᐯᐰᐱ ᐲᐳ

][4.2.2 Select printer and controlWhen you execute CardPrinterTest, it will search connected printers by USB and Networkautomatically and SMART-50 printer connected to USB has higher priority. Other printers could beselected by pull-down menu. You can test all function with connected printer.. Control is consisted by SBS(Step by Step), Move, Rotate, Etc. section and you can control printer byeach step.zSBSSBS is to operate SMART-50 printer in SBS(Step-By-Step) mode which you can control theprinter using commands. In SBS mode, after printing data transmission, printing a card will berun only by clicking “DoPrint”. It is the main difference between NORMAL mode and SBS mode.When you click “Start”, SMART-50 is operated in SBS mode, and existing spooled data will beeliminated. To exit SBS mode, click “Stop”.zCardCard is to bring a card into printer and eject a card. “In” is to move a card from input hopper toprinter and “Out” is to move a card from printer to output hopper. In case the flipper is installed,“Back” ejects a card to the back side.zMoveMove is to move a card to specific position in the inside of printer. “Print” is to move a card tothe printing position, and “Mag.” is to the magnetic encoding position, and “IC” is to the contactsmartcard encoding position, and “RF” is to the contactless smartcard encoding position. “ToRotator” is to move a card from printer to flipper and “From Rotator” is to move a card fromflipper to printer. “from In” is to move a card from the card in sensor to where you defineposition, and “from Out” is to move a card from the card out sensor to where you define position.zRotateRotator is to flip over a card in the printer installed flipper. “Auto” is to move a card from printerto flipper and flip over a card and move a card to the printing position automatically. “Batch” isto repeat “Auto” as many times as the number of set. “To Bottom” is to turn to the backside ofcard and “To Top” is to turn to the front side of card.zEtc“Cleaning Roller” is to clean the roller by cleaning card automatically. “Use Log” is to display login message space.4.2.3 PrintPrint can be done through the CSD file which is designed by Smart Design program. Following thesteps in this section.1. Click “…” button and select the CSD file.2. Click “Open” button to prepare CSD file to print.3. Click “Print” Button to move print data to spool. In the NORMAL mode, Click “Print” button toprint a card, but in the SBS mode, “Print” button to transmit a printing data from PC to printerand wait for printing. Therefore, you must click “DoPrint” to print in SBS mode. This function isfor detail control of printer.4. Click “Close” button to close CSD file.4.2.4. BatchBatch is to repeat encoding/decoding test continuously. In the Repeat, you input the number of repeatand click “Batch Start”, then the test is run as many times as the number of set. When you check“Include Card In/Out”, each time the printer bring a card from input hopper and perform an encoding

$]\test and eject the card. But if not, encoding test will be done only by one card. At that time, if there is nocard in the printer, the printer bring a card into the printer from input hopper and repeat the encoding teston the card, and if there is a card in the printer, the encoding test is performed on the card repeatedly.“Card Holding” is activated when “Include Card In/Out” is ticked. When “Card Holding” is ticked and therepeat number is set, the printer repeats the encoding test as many times as the number of set in the“Card Holding” without ejection. When it is completed, the printer ejects the card and brings a new cardinto the printer and starts testing.In the Setting, “Retry” is to retry the encoding test when the error occurred. “Prompt on Error”istodisplay Pop up Message when the error occurred. If not, Error number will be counted without message.The number of error is displayed at Error section.4.2.5. EncodingMagnetic: Magnet Stripe Encoding“Read” is to read and display the data from magnetic stripe card. It is composed of “Do Read”and “Read All Buffer” and runs “Do Read” and “Read All Buffer” sequentially.“Do Read” is to read the data from magnetic stripe card and store the data in the buffer.“Read All Buffer” is to transmit the date stored in the buffer to PC. If the track number is ticked,the data of the ticked track is only transmitted to PC.“Write” is to write the data to the magnetic stripe. It is composed of “Write All Buffer” and “DoWrite” and runs “Write All Buffer” and “Do Write” sequentially.“Write All Buffer” is to transmit the data to the buffer.“Do Write” is to write the data stored in the buffer to the magnetic stripe of card. You canchoose the magnetic foil type (LoCo or HiCo) and the track of magnetic stripe. “Random Fill” isto create a random magnetic encoding data for testing.Batch process repeats the following steps sequentially, Card “IN” ÆMove “Mag” ÆMagnetic“Random Fill” ÆMagnetic “Write” ÆMagnetic “Read” ÆCard “OUT”.Pic.117 Magnetic stripe encodingIC(PC/SC) : Contact Smartcard EncodingIn SMART-30 printer, a contact smartcard encoder can be installed and SMART-50 printersupports the contact smartcard encoder in the printer inside and the SIM encoder on the right offront side. “IC(PC/SC)” is to test a contact smartcard and SIM encoding.“Batch” is applied only to the contact smartcard encoding because SIM encoder is installedoutside and can’t move a card automatically.“ICH Contact” is to bring the encoder head into contact with the IC chip of smartcard physically.$

]]“ICH Discontact” is to separate the encoder head from the IC chip of smartcard physically.“Init” is to recognize and display the installed contact smartcard reader.The recognizedencoder will be displayed at the pull down control.“Contact” is to contact with the smartcard electrically and initialize.“Reset” is to finish the function electrically. After “Contact”, you can run “Get ATR”, “Read”,“Write” and “Clear”.“Get ATR” is to read the ATR data.“Read” and “Write” are to read and write the defined data (Name, Address and Phone). Thesecould not be applied to all cards.“Clear” is to clear the displayed data (ATR, Name, Address and Phone).In case the data is read and written using APDU, Read/Write can be done by APDU commands.“Load APDU” is to read the stored APDU commands.“Save APDU” is to save the displayed APDU commands.“Clear APDU” is to clear the APDU section.“Send APDU” is to run the APDU commands.Batch process repeats the following steps sequentially, Card “IN” ÆMove “IC” ÆIC “ICHContact” ÆIC “Init” ÆIC “Contact” ÆIC “Reset” ÆIC “ICH Dis-contact” ÆCard “OUT”.Pic.118 Contact smartcard encodingRF(PC/SC) : Contactless Smartcard EncodingIn SMART-30 printer, a contactless smartcard encoder can be installed and SMART-50 printerhas the internal and external contactless smartcard encoder. RF(PC/SC) is to read and write thecontactless smartcard. Using internal encoder, the printer brings a card into the printer from inputhopper and encodes a smartcard. Using external encoder, after putting a card on the top cover,you can encode because the antenna installed under the top cover is used. Therefore, “Batch” isapplied only to the internal contactless smartcard encoding.“Contact” is to contact with the contactless smartcard electrically and initialize.“Reset” is to finish the function electrically. After “Contact”, you can run “Read”, “Write” and“Clear”.“Get UID” is for getting Chip Serial Number(CSN)“Read” and “Write” are to read and write the defined data (Name, Address and Phone). Thesecould not be applied to all cards.

]^“Clear” is to clear the displayed data (ATR, Name, Address and Phone).In case the data is read and written using APDU, Read/Write can be done by APDU commands.“Load APDU” is to read the stored APDU commands.“Save APDU” is to save the displayed APDU commands.“Clear APDU” is to clear the APDU section.“Send APDU” is to run the APDU commands.Batch process repeats the following steps sequentially, Card “IN” ÆMove “RF” ÆRF“Connect” ÆGet UIDÆRF “Discontact” ÆCard “OUT”Pic.119 Contactless smartcard encoding4.2.6. Printer status“Get Temperature” is to get and display the temperature of Thermal Print Head. When the “RealtimeCheck” is ticked, it displays the current temperature of Thermal Print Head in real time.“Get Status” is to get and display the printer status.Status Code#define SMSC_M_CARDIN 0x0000000000000001 // Card In#define SMSC_M_CARDOUT 0x0000000000000002 // Card Out#define SMSC_M_MOVE_PRINT 0x0000000000000004 // Move to print#define SMSC_M_MOVE_PRN2ROT 0x0000000000000008 // Move from printer to flipper#define SMSC_M_MOVE_ROT2PRN 0x0000000000000010 // Move from flipper to printer#define SMSC_M_MOVE_IC 0x0000000000000020 // Move to contact encode#define SMSC_M_MOVE_RF 0x0000000000000040 // Move to contactless encode#define SMSC_M_MOVE_MAG 0x0000000000000080 // Move to Magnetic encode#define SMSC_M_THUP 0x0000000000000100 // Thermal head up#define SMSC_M_THDOWN 0x0000000000000200 // Thermal head down#define SMSC_M_ICHUP 0x0000000000000400 // Contact head up#define SMSC_M_ICHDOWN 0x0000000000000800 // Contact head down#define SMSC_M_PRINT 0x0000000000001000 // Printing#define SMSC_M_MAGRW 0x0000000000002000 // Read/Write Magnetic data#define SMSC_M_SEEKRIBBON 0x0000000000004000 // Ribbon search#define SMSC_M_MOVERIBBON 0x0000000000008000 // Ribbon Move#define SMSC_M_ROTATORTOP 0x0000000000010000 // Rotate Card up

]_#define SMSC_M_ROTATORBOTTOM 0x0000000000020000 // Rotate Card down#define SMSC_S_HOPPERHASCARD 0x0000000000040000 // Card in hopper#define SMSC_S_THUP 0x0000000000080000 // Thermal head up#define SMSC_S_CARDIN 0x0000000000100000 // Detect Card in#define SMSC_S_CARDOUT 0x0000000000200000 // Detect Card out#define SMSC_S_ROTATORTOP 0x0000000000400000 // Card front side up in Flipper#define SMSC_S_EQUIPROTATOR 0x0000000000800000 // Flipper installed#define SMSC_M_RECVPRINTDATA 0x0000000001000000 // Importing print buffer#define SMSC_S_HASPRINTBUFFER 0x0000000002000000 // Reserving print buffer#define SMSC_M_SBSRUNNING 0x0000000004000000 // Executing SBS Commands#define SMSC_S_SBSMODE 0x0000000008000000 // SBS mode#define SMSC_S_CASEOPEN 0x0000000010000000 // Case open#define SMSC_M_INIT 0x0000000020000000 // Initializing#define SMSC_S_TESTMODE 0x0000000080000000 // Test modeFrom card printer firm-ware version 1.00.60 , some values are changed like bellows from black colortexts to red color texts.#define SMSC_S_THUP 0x0000000000080000 // Thermal head up status#define SMSC_S_CLEANWARNING 0x0000000000080000 // Need cleaning of printer#define SMSC_S_ROTATORTOP 0x0000000000400000 // Front card up status in rotator#define SMSC_S_EQUIPLAMINATOR 0x0000000000400000 // Laminator is installedError Code#define SMSC_F_CARDIN 0x0000000100000000 // Error Card in#define SMSC_F_MOVETOPRINT 0x0000000200000000 // Card move Error#define SMSC_F_CARDOUT 0x0000000400000000 // Card out Error#define SMSC_F_MOVETOMAG 0x0000000800000000 // Card move Error (Magnetic)#define SMSC_F_MOVETOIC 0x0000001000000000 // Card move Error (Contact)#define SMSC_F_MOVETORF 0x0000002000000000 // Card move Error (Contactless)#define SMSC_F_MOVETOROTATOR 0x0000004000000000 // Card move Error (Printer to Flipper)#define SMSC_F_MOVEFROMROTATOR 0x0000008000000000 // Card move Error (Flipper to Printer)#define SMSC_F_THUP 0x0000010000000000 // Thermal head up Error#define SMSC_F_THDOWN 0x0000020000000000 // Thermal head down Error#define SMSC_F_ICHUP 0x0000040000000000 // Contact head up Error#define SMSC_F_ICHDOWN 0x0000080000000000 // Contact head down Error#define SMSC_F_ROTATORTOP 0x0000100000000000 // Card rotate up Error#define SMSC_F_ROTATORBOTTOM 0x0000200000000000 // Card rotate down Error#define SMSC_F_PRINT 0x0000400000000000 // Printing Error#define SMSC_F_MAGRW 0x0000800000000000 // Magnetic data Read/Write Error#define SMSC_E_SEEKRIBBON 0x0001000000000000 // Ribbon search Error#define SMSC_E_MOVERIBBON 0x0002000000000000 // Ribbon move Error#define SMSC_E_NOTH 0x0004000000000000 // Uninstalled Thermal head#define SMSC_E_THOVERHEAT 0x0008000000000000 // Overheat Thermal head#define SMSC_E_EMPTYRIBBON 0x0010000000000000 // No Ribbon#define SMSC_F_DATA 0x0020000000000000 // Data Error#define SMSC_F_CARDBACKOUT 0x0040000000000000 // Card out to back Error#define SMSC_F_CARDERASE 0x0080000000000000 // Cannot Remove data#define SMSC_F_INCORRECT_PW 0x0100000000000000 // Incorrect Password#define SMSC_F_MAGREADT1 0x0200000000000000 // Read data Error Mag. Track.1#define SMSC_F_MAGREADT2 0x0400000000000000 // Read data Error Mag. Track.2#define SMSC_F_MAGREADT3 0x0800000000000000 // Read data Error Mag. Track.3#define SMSC_F_LOCKED 0x1000000000000000 // Device Locked#define SMSC_F_SPOOLFULL 0x2000000000000000 // Exceed Printer Spool#define SMSC_F_SET 0x4000000000000000 // Recent motion failLaminator’s Status Code#define LMSC_M_HEATHDRLIFTUP 0x0000000000000001 // Heat-header is being lifted up#define LMSC_M_HEATHDRLIFTDOWN 0x0000000000000004 // Heat-header is being lifted down#define LMSC_M_CARDIN 0x0000000000000010 // Card In#define LMSC_M_MOVE_LAMINATE 0x0000000000000040 // Moving to laminate position#define LMSC_M_FRONTCARDOUT 0x0000000000000100 // Card is being moved out to front.#define LMSC_M_REARCARDOUT 0x0000000000000200 // Card is being moved out to rear.#define LMSC_M_ROTATE 0x0000000000000400 // Rotating#define LMSC_S_WAIT 0x0000000000000800 // Waiting#define LMSC_S_CMDRUN 0x0000000000002000 // Command is being executed.#define LMSC_M_HEATING 0x0000000000004000 // Heating Heat-header#define LMSC_S_CASEOPEN 0x0000000000008000 // Top cover is opened#define LMSC_M_LAMINATING 0x0000000000010000 // Laminating#define LMSC_S_CARDINSENSOR 0x0000000020000000 // Caught by card in sensor

]`#define LMSC_S_CARDOUTSENSOR 0x0000000040000000 // Caught by card out sensor#define LMSC_S_OUTDOORSENSOR 0x0000000080000000 // Caught by stacker open sensorLaminator’s Error Code#define LMSC_E_HEATHDRLIFTUP 0x0000000100000000 // Error while lifting up Heat-header#define LMSC_E_HEATHDRLIFTDOWN 0x0000000400000000 // Error while lifting down Heat-header#define LMSC_E_CARDIN 0x0000001000000000 // Error while moving card in#define LMSC_E_MOVE_LAMINATE 0x0000004000000000 // Error while moving to Laminate position.#define LMSC_E_FRONTCARDOUT 0x0000010000000000 // Error while front card out (printer side)#define LMSC_E_REARCARDOUT 0x0000020000000000 // Error while rear card out (stacker side)#define LMSC_E_ROTATE 0x0000040000000000 // Error while rotating#define LMSC_E_INIT 0x0000800000000000 // Error while initializing laminator#define LMSC_E_EMPTYFILM 0x0001000000000000 // Film remain count is 0.#define LMSC_E_NOFILM 0x8000000000000000 // No film is installed, or cannot4.3. Firmware upgradeWhen you run the CardPrinterFirmware, you can see the pop-up window as the Pic. 120.Device: Select the local printer that you want to upgrade.Card Printer / Laminator: Select the device you want upgrade.Device Version: Displays the current firmware version of selected printer.Binary File: Click “Browse” button and select new firmware file to update.Manual Update: It is used when you want to upgrade manually.Update: Upgrades automatically. In generally, we recommend upgrading automatically.Close: Exit.Message : It displays information of upgrading.Pic.120 Upgrading printer firmware

^W4.3.1. Card Printer Firm-ware Upgrade.If you click “Browse” and select the new firmware, “Manual Update” and ”Update” are activated. At thattime, click “Update” button to upgrade automatically, then the printer is upgraded after rebooting.(Caution: Please do not close upgrade dialog box until it is completed successfully and do not turn offthe printer.)Pic.121 Ready for firm-ware upgradeIn case there are some problems in the automatic upgrade, you click “Manual Update” and can see thepop-up widow as below picture. It shows procedure of manual upgrade. You can upgrade manuallyaccording to this procedure.Pic.122 Firm-ware manual upgrade

^X4.3.2. Laminator Firm-ware Upgrade.This function is only for card printer firm-ware version 1.00.60 and laminator should be installed to theprinter. If you click “Browse” and select the new firmware, “Manual Update” and ”Update” are activated.At that time, click “Update” button to upgrade automatically, then the printer is upgraded after rebooting.(Caution: Please do not close upgrade dialog box until it is completed successfully and do not turn offthe printer.)Pic.123 Ready for laminator firm-ware upgradeIn case there are some problems in the automatic upgrade, you click “Manual Update” and can see thepop-up widow as below picture. It shows procedure of manual upgrade. You can upgrade manuallyaccording to this procedure.Pic.124 Firm-ware manual upgrade

$^Y5. Optional device driver installationIn SMART-50 printer, you can install the optional devices that encode contact smartcard orcontactless smartcard. If your purchased SMART-50 printer has optional devices, you should alsoinstall the smart card reader drivers.5.1. Contact smartcard readerIn SMART-50 printer, you can install the two types of optional devices which are contactsmartcard reader and mobile SIM smartcard reader. If you have one or more smartcard readerdevices on your printer, you should install the smartcard device driver as in the following, andconnect SMART-50 printer to your PC.5.1.1. Run the smartcard driver installerInsert the smartcard installation CD and find “\Options\Gemalto PC Twin” directory on yourCD. Find the right directory which is installed OS version on your PC, and run the installer.You can see the smartcard reader driver installation window as the Pic.125. And click “Next”.Pic.125 Contact smartcard reader driver installation$

^Z5.1.2. License agreementThe license agreement window as the Pic.126 is shown. Check at the agreement and click“Next”.Pic.126 License agreement5.1.3. InstallationThe installation message is shown as the Pic.127. Click “Install” to install driver.Pic.127 Installing the contact smartcard reader driver

^[5.1.4. Complete installationWhen the installation is completed, the window as the Pic.128 is shown. Click the “Finish” tocomplete the installation steps.Pic.128 Completing the smartcard reader driver installation

$^\5.2. Contactless smartcard readerIn SMART-50 printer, you can install the two types of smartcard reader which are internalcontactless smartcard reader and external contactless smartcard reader. If you have one ormore contactless smartcard reader devices on your printer, you should install the contactlesssmartcard device driver as in the following, and connect SMART-50 printer to your PC.5.2.1. Connect SMART-50 printer to PCWhen you connect the printer to PC and turn on the printer, you can see the “Found NewHardware Wizard” as the Pic.129, then Check “No, not that time” and Click “Next” to continue.Pic.129 Found New Hardware Wizard5.2.2. Choose the installation methodAt the window as the Pic.130, select “Install from a list or specific location” and click “Next”.Pic.130 Installation method selection$

$^]5.2.3. Driver locationInsert the smartcard installation CD and find “\Options\ Omnikey 5121” directory on your CD.Find the right directory which is installed OS version on your PC, and select the directory asthe Pic.131, and click “Next”.Pic.131 Driver location5.2.4. Complete installationWhen the installation is completed, the window as the Pic121 is shown, click “Finish” tocomplete the installation steps.Pic.132 Completing the driver installation$

^^6. Troubleshooting6.1. Cleaning the printerTo maintain the best condition of SMART-50 printer, you must clean the printer periodically. If youuse the exclusive cleaning card as the Pic.133, you can clean the printer easily. For purchase theexclusive cleaning card, ask to SMART-50 printer provider.Pic.133 Exclusive cleaning card for SMART-50 printerIf the exclusive cleaning card is ready, click the “Clean Printer” in the service tab of SMART-50printer driver as the Pic.134. After click, Clean Printer program to clean the printer is run.Pic.134 Printer cleaning startStep 1. Connect the SMART-50 printer to PC and turn it on, and prepare the exclusive cleaningcard.

^_Pic.135 Printer cleaning Step 1Step 2. Open the hopper and top cover and remove the card and ribbon cartridge.Pic.136 Printer cleaning Step 2Step 3. Insert the exclusive cleaning card into the printer through input hopper as the Pic.137. When

^`the exclusive cleaning card is inserted to the cleaning roller, it will be move automatically. Itis normal that the exclusive cleaning card is inserted to the ends and rollers are moving toclean.Pic.137 Printer cleaning Step 3Step 4. Close the top cover to clean the Thermal Print Head and the printing roller. When the topcover is closed, cleaning card will be moving back and forth to clean.Pic.138 Printer cleaning Step 4Step 5. Wait until the cleaning is completed. When the cleaning is completed, the exclusive cleaning

_Wcard will be ejected automatically as the Pic.139.Pic.139 Printer cleaning Step 5Step 6. Remove the exclusive cleaning card and install ribbon cartridge into the printer.Pic.140 Printer cleaning Step 6

_X6.2 TPH (Thermal Print Head) replacement1. Check the serial number and theresistance of new Thermal Print Headas the Pic. 141TPH type: A = KEE, B = KPESerial No.: see the red box.TPH resistance: see the green box.Pic.141 Thermal Print Head2. Set up the new TPH’s configuration using CardPrinterSetup program.Step1: Run ‘Card Printer Setup’ in Utilities of the installation CD and click expansion button.Step2: Click “Change Header” in the extended setup.Step3: Input the TPH’s Serial No., Resistance and Type (choose KEE or KPE) on the TPH’s label,and click “OK”.Step4: Click “Set Config” to set the new TPH’s configuration.Pic.142 Print head setup3. Replacing the new TPHStep1: Remove the old TPH from the top cover.(1) Turn off the printer and open the top cover.(2) Hold the TPH and press the locked hook, then the TPH is disconnected as the Pic. 143.(3) Disconnect the TPH from print head wire carefully.(Caution: TPH is possible to HOT.)Step2: Installing the new TPH(1) Connect new TPH to the print head wire.(2). Put the new TPH on the Shift and pull it up until be locked as the Pic. 143.

_YPic.143 Print head replacement4. Setup the print position and the color density.After installing the new TPH, you must reset the print position and the color density usingCardPrinterSetup utility. Refer to “4.1.2 Default setting”5. Calibration of Print HeadAngleTo get the best print quality, the TPHshould be located vertically with cardsurface.If print quality has the problem, it could becaused by print head angle.Through Adjusting print head angle byscrew (red mark in the Pic.144), you couldmake good quality of print.(Use the appropriate screw driver toadjust, and turn the screw by 90 degreesat a time.) Pic.144 Print head angle6.3. Card movement6.3.1. Cards can’t enter into the printer from input hopper.zNon-standard cards or bad cards.Change the cards. You can use only ISO CR-80 card (54mm x 86mm).zCard thickness control lever is set improperly.Regulate the card thickness control lever to fit the current card thickness.zBadcardarray.Array the cards again and put them on input hopper as section 2.2 in this manual.zCards have static and moisture.Remove the moisture or static.6.3.2. Card Transfer Error occurs when the ribbon is coiled around the transferroller or the printing roller.Open the top cover and remove the card and the coiled ribbon from SMART-50 printer usingfront LED buttons. If this problem occurred frequently, check the below things.zNon-standard cards or bad cards.Change the cards. You can use only ISO CR-80 card (54mm x 86mm).zThe transfer roller or the printing roller is contaminated with the dust and dirtRemove the dust and dirt with the cleaning kit as section 6.1zWrong printing position setting.Please contact the local supplierzWhen operating temperature and humidity is out of the acceptable operating limit of theprinter.Adjust the operating environment of the printer.

_Z6.3.3. An Error occurs while the card is being transferred.First of all, check the Error message at LCD display.Open the top cover and remove the card by LED buttons.If this problem occurs frequently, check the followings.zNon-standard cards or bad cards.Change the cards. You can use only ISO CR-80 card (54mm x 86mm).zPrinter setting is changed or is not proper.Please contact the local supplier.zThe transfer roller or the printing roller is contaminated with the dust and dirt.Remove the dust and dirt with the cleaning kit as section 6.1.zThe card surface is contaminated with the dust and dirt.Check the card surface and remove the dust and dirt and try again. If this problem occursagain, retry with new card.6.4. Printing quality6.4.1. Not printed or wrong colors printed spot.zThe card surface is contaminated with the dustand dirt.After checking the card, change it to another card.zThe cleaning roller is contaminated with thedust and dirt.Check the cleaning roller. If there is much dust,change the cleaning roller to the new one.zMuch dust in the printer.Clean the inside of the printer with the cleaning kit.6.4.2. Not printed horizontal line.zThe ribbon cartridge is installed improperly.Check the ribbon cartridge installation state andwhether the ribbon has wrinkles.zThe printer head is contaminated with the dustand dirt.Clean the printer head with cleaning kit.zThe printer head is damaged.Please contact the local supplier to replace theprinter head.6.4.3. Unclear or not uniform print.zUneven or bad card surface.Change the card.zToo high or low setting of the color density.Please contact the local supplier. The color densitydefault of your printer needs to be changed.zThe printer head is contaminated with the dustand dirt.Clean the printer head with cleaning kit.Pic.145 Printing quality trouble 1Pic.146Printing quality trouble2Pic.147Printing quality trouble 3

_[6.4.4. Not aligned color print.zNon-standard cards or bad cards.Change the cards. You can use only ISO CR-80card (54mm x 86mm).zUneven or bad card surface.Change the card.zThe transfer roller or printing roller iscontaminated with the dust and dirt.Clean the rollers with the cleaning kit as section 6.1.zWorn-out printer.Please contact the local supplier.6.4.5. Unplanned color print.zNon-standard cards or bad cards.Change the cards. You can use only ISO CR-80 card(54mm x 86mm).zUneven or bad card surface.Change the card.zThe transfer roller or printing roller iscontaminated with the dust and dirt.Clean the rollers with the cleaning kit as section 6.1.zWorn-out printer.Please contact the local supplier.6.5. Magnetic stripe encoding6.5.1. Magnetic encoding error.First of all, Please press left LED button to retry.zThe magnetic head is contaminated with the dust and dirt.Clean the magnetic head with the cleaning kit.zThe magnetic encoding data is not transmitted or the wrong data is transmitted.Check the setting of the program and the driver and the magnetic encoding data youtransmitted.zThe card is not magnetic card, or inserting direction is wrong.Change the card or the direction.zBad magnetic stripes on the card.Change the card.6.6. General operation6.6.1. Ribbon snapped during printing.Open the top cover and take out the cartridge. After putting the snapped pieces on together,install the cartridge again. Check the followings if this kind of problem occur frequently.zNon-standard cards or bad cards.Change the cards. You can use only ISO CR-80 card (54mm x 86mm).zToo high or low setting of the color density.Please contact the local supplier. The color density default of your printer needs to bechanged.Pic.148Printing quality trouble 4Pic.149Printing quality trouble 5

$_\6.6.2. LCD display “Ribbon Not Found”Press the left LED button to retry. If it occurs frequently, check the followings.zNot genuine ribbon.Change to the genuine ribbon.zRibbon is consumed.Printing is not possible if ribbon is used up. Change the ribbon.zSnapped ribbon.Open the top cover and take out the cartridge. After putting the snapped pieces on together,install the cartridge again.6.6.3. Printer doesn’t operate even if the printing data has been transmitted.Check the following.zPrinter power off.Check the power. Turn on the printer power.Check the printer adaptor whether it is connected with a socket and the printer.zBad power adaptor.Please contact the local supplier for replacement of the adaptor.zThe printer driver is “Offline”.Change the printer driver to “Online”.zThe printer’s USB cable is disconnected or the connection is bad.Check the cable’s connection between PC and the printer.If not good, make the USB cable connection again.zBad USB cable.Change the USB cable.zThe printing is operated with another printer driver.Select the correct SMART-50 printer driver again.zWrong USB port setting of the printer driver.Check the port setting of the printer driver and change the port setting.zNo ribbon in the printer or error occurred.Install ribbon in the printer or resolve the error.zToo long power or USB cable (more than 1.5M).Usethecableprovidedwiththeprinter.zPC’s USB port is down:Reboot your PC.$

IDP SMART-30S Card Printer User Manual

IDP Corp., Ltd. Card Printer

User Manual

Navigation menu

Namespaces

Views

Navigation