IDT Technology SMS002 Remote control User Manual

IDT Technology Limited Remote control

user manual

Download: IDT Technology SMS002 Remote control User Manual
Mirror Download [FCC.gov]IDT Technology SMS002 Remote control User Manual
Document ID3694265
Application IDOMR0gwTcIaOeiaKX6f+cTg==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize71.73kB (896654 bits)
Date Submitted2017-12-27 00:00:00
Date Available2017-12-28 00:00:00
Creation Date2017-04-10 11:34:54
Producing SoftwareAdobe PDF Library 9.9
Document Lastmod2017-04-10 11:34:57
Document Titleuser manual
Document CreatorAdobe InDesign CS5.5 (7.5.2)

INTRODUCTION
Thank you for purchasing the Huger board Neu. Please read this user manual before
using your new product.
This product is the most state of art skateboard design on the market and Li-Po battery
powered for high performance. It is controlled with the wireless controller and our
dedicated App, max speed up to 25 KM/H with 10 KM travel distance per one charger
that make you enjoy the most fun of skating.
Note: Please keep this manual handy as you use your new product. It contains practical
step-by-step instructions, as well as technical specifications and warnings you should
know about.
• Please use the skateboard in a suitable outdoor environment, and press the remote
control after standing steadily on the skateboard. Do not arbitrarily accelerate
skateboard in other environment.
• The product is only suitable for the user over the age of 14. Children under 14 years
of age must be accompanied by parents to play.
• Please wear protective equipments, such as: helmet, elbow and knee pads. Please wear
the right clothes to play. Do not barefoot or play on the beach. Fasten the shoelaces,
do not let the shoelaces contact the wheels and drive system, causing danger.
• Beginners/novices are recommended to use/practice at low speed and on a dry, flat
surface.
Huger board
Neu
SMS203
User Manual
GETTING STARTED
DOWNLOAD APP
Power indicators
Deck
• Only play on a flat, open road. Do not play on potholes, gravels, gravel, muddy, rugged,
ramps. Do not play on a smooth or wet ground, such as snow, ice, slippery ground,
to prevent slipping.
Horn On/Off
Scan the following QR coder or Search Oregon Scientific XXX to find the App to
download on your smart device. The App is available on both Apple App Store and
Google Play store.
Go/Stop switch
• Do not use the product on the carpet or places that not suitable for playing.
• Do not use the skateboard in rain and snow.
• Do not use your phone or headphones while playing.
• Do not hook the skateboard on other vehicles or drag other objects.
Taillights
Charging port
Turning lights
Power button
• Do not immerse the product in water, and the electronic drive parts will be damaged.
• For accessories replacement, only use the accessories with the same type and
specifications.
PACKAGING CONTENTS
• Adjust the front and rear wheels to ensure they run freely before playing.
• 1x Remote control
• Adjust the flexibility of the damping shim by the locknut.
• 1x Charger
• Do not touch the motor and the brakes during running or just after use to avoid hot.
• 1x USB charging cable
• This product is designed for people with safe driving ability. Please place the skateboard
in a place where children under 8 years of age are not touched.
• 2x Name card
• Please comply with local laws and regulations and use it in places where electric
skateboards are allowed.
• 1x User manual
headlights
CHARGE
Truck
Fully charge your skateboard and remote control before first use. Normal charging takes
about 1.5 hours for the main unit and 1 hours for the remote.
Front wheels
Rear wheels
• If you have any problem during using, operating, repairing, please contact customer
service.
• Check the surroundings before playing. For the user who is unfamiliar with the
operations must be far away from crowds. Improper operation may cause serious
body injury and property damage.
• Please be careful to drive. Accidentally encountered obstacles in the process will cause
the skateboard out of control. Please be careful to avoid pedestrians and other means
of transport (such as: balance cars, skateboards, bicycles, etc.).
MAIN UNIT
MAIN UNIT
• Do not try the action of the skateboard on the electric skateboard, such as bounce,
jerk and other actions.
• Do not use skateboards at night or in poor vision.
IMPORTANT SAFETY PRECAUTIONS!
OVERALL
Forward/Reverse
High/Low speed mode switch
2. Connect the supplied USB charging cable to the charging port of the remote, and
then plug into a computer or an adapter. The power indicator for the remote lights
red during charging and turns green when fully charged.
3. Check the App or power indicators on the battery compartment to find the power
capacity of the skateboard.
• 1x Skateboard
• 1x T tool
1. Connect the supplied charger to the charging port of the skateboard, and then plug
into a standard household outlet. The power indicator on the charger lights red during
charging, and turns green when fully charged.
4. Check the power indicators on the remote to find the power capacity of the remote.
Horn
Battery compartment
Signal indicator
Power button
USB charging port
LEDs
Color
Power
Green
Full
Green
75%
Green
50%
Red
<25%
end of their useful life must be given to waste disposal centers specializing in separate
collection of waste electrical
PLAY YOUR SKATEBOARD
Specifications
• If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention.
• The built-in battery may discharge completely after a long period without use. Recharge
the battery before use.
1. Press the power button to turn on/off the skateboard. The headlights turn on.
Items
Specification
Remark
3. Push the Go/Stop switch forward to go, release to stop.
Drive Unit
10 A, 200 W BLDC single motor
at rear wheels
4. Hold the Go/Stop switch backward to turn on the taillights. Double press the power
button on the remote to turn on/off the headlights.
Speed
Normal Speed mode: ≤18 km/h
At 75 Kg loading
2. Press and hold the power button for 3 seconds to turn on/off the remote.
5. Changing the playing mode by Forward/Reverse and High/Low speed switches.
NOTE
• Taillights beam in normal mode; Flash by automatically detect in stop mode.
• Left and right turning indicators will flash and are controlled by Gyroscope automatically
when turning direction.
High speed mode: ≤25 km/h
Endurance
Mileage
Normal mode: ≤10 km
Remote Control
BLE 4.0 module connected to Mobile
At 75 Kg loading
High speed mode: ≤10 km
Pedal and brake control
Battery
Open the App, it will find the skateboard automatically. With the App, you can
• Use only the supplied charger and cable for charging.
• Charge batteries on a fireproof surface away from flammable items or liquids.
• Do not charge inside an automobile, especially while driving.
• Follow the instructions for charging. Do not charge longer than recommended. Unplug
the USB cable when the battery is charged.
PRECAUTIONS
Forward/Reverse control
APP OPERATIONS
• The skateboard should never be left unattended while charging.
• Do not subject the device to excessive force, shock, dust, temperature or humidity.
LG MG1 Power battery pack
(7x 18650 - 3.6 V) (3200 mAh-1S7P)
• Do not immerse the device in water. If you spill liquid over it, dry it immediately with a
soft, lintfree cloth.
• Check the power, light, speed status
Size
560 mm x 220 mm x 117 mm
• Do not clean the device with abrasive or corrosive materials.
• Set the horn sound and light colour
Recharge Time
1~1.5 hr
• Do not tamper with the device’s internal components. Doing so invalidates the warranty.
• Turn on/off the headlights and taillights
Wheel Base
Diameter: 73 mm
• Images shown in this manual may differ from the actual display.
PAIR SKATEBOARD WITH REMOTE
Weight
About 3.9 kg
• When disposing of this product, ensure it is collected separately for special treatment.
NOTE: The remote and the skateboard are paired in the factory. If a new remote is
needed, pair the new remote with the skateboard before using.
Board Material
Canadian Maple Wood
Max Load
100 kg
• The contents of this manual may not be reproduced without the permission of the
manufacturer.
Operation
Conditions
-10 to 60 C
≤85 % R.H.
Storage Condition
-20 to 80 0C
≤95 % R.H.
1. Turn off the skateboard and the remote.
2. Pull the Go/Stop switch as far backwards as it will allow.
3. Turn on the remote. The Signal indicator of the remote flashes quickly.
4. Turn on the skateboard.
LITHIUM BATTERY SAFETY INSTRUCTIONS
5. Release the Go/Stop switch. The Signal indicator of the remote lights steady. The
remote and the skateboard are successfully paired.
• Do not burn or bury batteries. Do not puncture or crush. Do not disassemble.
• Recycle lithium batteries. Do not dispose of in the trash
• If the electrolyte in the cells should get on your skin, thoroughly wash with soap and
water.
NOTE:The technical specifications for this product and the contents of the user manual
are subject to change without notice.
NOTE: Features and accessories will not be available in all countries. For more
information, please contact your local retailer. To download an electronic version of the user
manual, please visit http://global.oregonscientific.com/customerSupport.php.
ABOUT OREGON SCIENTIFIC
Visit our website www.oregonscientific.com to learn more about Oregon Scientific
products.
For any inquiry, please contact our Customer Service at info@oregonscientific.com.
Oregon Scientific Global Distribution Limited reserves the right to interpret and construe
any contents, terms and provisions in this user manual and to amend it, at its sole
discretion, at any time without prior notice. To the extent that there is any inconsistency
between the English version and any other language versions, the English version
shall prevail.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may cause undesired
operation.
WARNING Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.
This Class B digital apparatus complies with Canadian ICES-3(B)/NMB-3(B)
DECLARATION OF CONFORMITY
The following information is not to be used as contact for support or sales. Please call
our customer service number (listed on our website at www.oregonscientific.com), or
on the warranty card for this product for all inquiries instead.
We
Name:
Oregon Scientific, Inc.
Address:
Centerpointe Center 5 Centerpointe Drive, Suite 400
Office no. 11 & 19 Lake Oswego, Oregon 97035
Telephone No.:
971-204-0378
declare that the product
Product No.:
SMS203
Product Name:
Huger board Neu
Manufacturer:
IDT Technology Limited
Address:
Block C, 9/F, Kaiser Estate, Phase 1, 41 Man Yue St.,
Hung Hom, Kowloon, Hong Kong
EU – DECLARATION OF CONFORMITY
Hereby the manufacturer, IDT Technology Limited, declares that the radio equipment
type [Huger board Neu (SMS203).] is in compliance with 2014/53/EU Directive. The full
text of the EU Declaration of Conformity is available at the following internet address :
www.oregonscientific.com
COUNTRIES RED APPROVED COMPLIED
All EU countries, Switzerland and Norway
DISPOSAL INFORMATION FOR USERS
Pursuant to and in accordance with Article 14 of the Directive 2012/19/EU of
the European Parliament on waste electrical and electronic equipment
(WEEE), and pursuant to and in accordance with Article 20 of the Directive
2013/56/EU of the European Parliament on batteries and accumulators and
waste batteries.
The barred symbol of the rubbish bin shown on the equipment indicates that, at the end
of its useful life, the product must be collected separately from other waste.
Please note that the batteries/rechargeable batteries must be removed from the
equipment before it is given as waste. To remove the batteries/accumulators refer to
the specifications in the user manual. Therefore, any products that have reached the
and electronic equipment, or given back to the dealer when purchasing a new WEEE,
pursuant to and in accordance with Article 14 as implemented in the country.
The adequate separate collection for the subsequent start-up of the equipment sent to
be recycled, treated and disposal of in an environmentally compatible way contributes
to preventing possible negative effects on the environment and health and optimizes
the recycling and reuse of components making up the apparatus.
Abusive disposal of the product by the user involves application of the administrative
sanctions according to the laws in force.
Warning
changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. changes or modifications not expressly approved
by the party responsible for compliance could void the user's authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: This device and its antenna(s) must not be coÿlocated or operation in
conjunction with any other antenna or transmitter.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.2-c003 61.141987, 2011/02/22-12:03:51
Create Date                     : 2017:04:10 11:34:54+08:00
Metadata Date                   : 2017:04:10 11:34:57+08:00
Modify Date                     : 2017:04:10 11:34:57+08:00
Creator Tool                    : Adobe InDesign CS5.5 (7.5.2)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 3939 bytes, use -b option to extract), (Binary data 4317 bytes, use -b option to extract)
Instance ID                     : uuid:3fc7bfaf-3dde-2744-ab11-35d8ae80485f
Document ID                     : xmp.did:34D2904819206811808391988194D5E3
Original Document ID            : xmp.did:34D2904819206811808391988194D5E3
Rendition Class                 : proof:pdf
History Action                  : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:34D2904819206811808391988194D5E3, xmp.iid:39D2904819206811808391988194D5E3, xmp.iid:3AD2904819206811808391988194D5E3, xmp.iid:6A0F6A0E1B206811808391988194D5E3, xmp.iid:6F0F6A0E1B206811808391988194D5E3, xmp.iid:740F6A0E1B206811808391988194D5E3, xmp.iid:BCC2B5701B206811808391988194D5E3, xmp.iid:FB7F1174072068118A6DA1B89D52A77F, xmp.iid:00801174072068118A6DA1B89D52A77F, xmp.iid:518522090B2068118A6DA1B89D52A77F, xmp.iid:528522090B2068118A6DA1B89D52A77F, xmp.iid:23C58692072068118C14AD017DB90559, xmp.iid:29C58692072068118C14AD017DB90559, xmp.iid:4D55294C082068118C14AD017DB90559, xmp.iid:F2A8BD01112068118C14AD017DB90559, xmp.iid:F8A8BD01112068118C14AD017DB90559, xmp.iid:2988CC30132068118C14AD017DB90559, xmp.iid:7C5CF544132068118C14AD017DB90559, xmp.iid:825CF544132068118C14AD017DB90559, xmp.iid:91901DA7132068118C14AD017DB90559, xmp.iid:97901DA7132068118C14AD017DB90559, xmp.iid:CC05F8DB132068118C14AD017DB90559, xmp.iid:D205F8DB132068118C14AD017DB90559, xmp.iid:5944A20C142068118C14AD017DB90559, xmp.iid:6044A20C142068118C14AD017DB90559, xmp.iid:607D8162152068118C14AD017DB90559, xmp.iid:C0E0EF00192068118C14AD017DB90559, xmp.iid:C7E0EF00192068118C14AD017DB90559
History When                    : 2017:03:30 11:27:30+08:00, 2017:03:30 11:35:54+08:00, 2017:03:30 11:35:54+08:00, 2017:03:30 11:40:12+08:00, 2017:03:30 11:40:41+08:00, 2017:03:30 11:41:17+08:00, 2017:03:30 11:42:57+08:00, 2017:03:31 11:58:33+08:00, 2017:03:31 11:58:53+08:00, 2017:03:31 12:24:12+08:00, 2017:03:31 12:24:39+08:00, 2017:04:10 09:28:02+08:00, 2017:04:10 09:28:13+08:00, 2017:04:10 10:34:58+08:00, 2017:04:10 10:35:34+08:00, 2017:04:10 10:50:44+08:00, 2017:04:10 10:51:12+08:00, 2017:04:10 10:51:46+08:00, 2017:04:10 10:52:59+08:00, 2017:04:10 10:54:31+08:00, 2017:04:10 10:55:25+08:00, 2017:04:10 10:55:59+08:00, 2017:04:10 10:56:40+08:00, 2017:04:10 10:57:21+08:00, 2017:04:10 11:03:20+08:00, 2017:04:10 11:06:54+08:00, 2017:04:10 11:32:49+08:00, 2017:04:10 11:34:06+08:00
History Software Agent          : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata
Doc Change Count                : 237
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CS5.5 (7.5.2)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NMTSMS002

Navigation menu