IDT Technology SMS003 Single motor four wheel E-skateboard User Manual
IDT Technology Limited Single motor four wheel E-skateboard
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3689742 |
| Application ID | Mf34HgC64LCIyhX5iJ4xIw== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | Yes |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 71.73kB (896654 bits) |
| Date Submitted | 2017-12-22 00:00:00 |
| Date Available | 2017-12-22 00:00:00 |
| Creation Date | 2017-04-10 11:34:54 |
| Producing Software | Adobe PDF Library 9.9 |
| Document Lastmod | 2017-04-10 11:34:57 |
| Document Title | user manual |
| Document Creator | Adobe InDesign CS5.5 (7.5.2) |
INTRODUCTION Thank you for purchasing the Huger board Neu. Please read this user manual before using your new product. This product is the most state of art skateboard design on the market and Li-Po battery powered for high performance. It is controlled with the wireless controller and our dedicated App, max speed up to 25 KM/H with 10 KM travel distance per one charger that make you enjoy the most fun of skating. Note: Please keep this manual handy as you use your new product. It contains practical step-by-step instructions, as well as technical specifications and warnings you should know about. • Please use the skateboard in a suitable outdoor environment, and press the remote control after standing steadily on the skateboard. Do not arbitrarily accelerate skateboard in other environment. • The product is only suitable for the user over the age of 14. Children under 14 years of age must be accompanied by parents to play. • Please wear protective equipments, such as: helmet, elbow and knee pads. Please wear the right clothes to play. Do not barefoot or play on the beach. Fasten the shoelaces, do not let the shoelaces contact the wheels and drive system, causing danger. • Beginners/novices are recommended to use/practice at low speed and on a dry, flat surface. Huger board Neu SMS203 User Manual GETTING STARTED DOWNLOAD APP Power indicators Deck • Only play on a flat, open road. Do not play on potholes, gravels, gravel, muddy, rugged, ramps. Do not play on a smooth or wet ground, such as snow, ice, slippery ground, to prevent slipping. Horn On/Off Scan the following QR coder or Search Oregon Scientific XXX to find the App to download on your smart device. The App is available on both Apple App Store and Google Play store. Go/Stop switch • Do not use the product on the carpet or places that not suitable for playing. • Do not use the skateboard in rain and snow. • Do not use your phone or headphones while playing. • Do not hook the skateboard on other vehicles or drag other objects. Taillights Charging port Turning lights Power button • Do not immerse the product in water, and the electronic drive parts will be damaged. • For accessories replacement, only use the accessories with the same type and specifications. PACKAGING CONTENTS • Adjust the front and rear wheels to ensure they run freely before playing. • 1x Remote control • Adjust the flexibility of the damping shim by the locknut. • 1x Charger • Do not touch the motor and the brakes during running or just after use to avoid hot. • 1x USB charging cable • This product is designed for people with safe driving ability. Please place the skateboard in a place where children under 8 years of age are not touched. • 2x Name card • Please comply with local laws and regulations and use it in places where electric skateboards are allowed. • 1x User manual headlights CHARGE Truck Fully charge your skateboard and remote control before first use. Normal charging takes about 1.5 hours for the main unit and 1 hours for the remote. Front wheels Rear wheels • If you have any problem during using, operating, repairing, please contact customer service. • Check the surroundings before playing. For the user who is unfamiliar with the operations must be far away from crowds. Improper operation may cause serious body injury and property damage. • Please be careful to drive. Accidentally encountered obstacles in the process will cause the skateboard out of control. Please be careful to avoid pedestrians and other means of transport (such as: balance cars, skateboards, bicycles, etc.). MAIN UNIT MAIN UNIT • Do not try the action of the skateboard on the electric skateboard, such as bounce, jerk and other actions. • Do not use skateboards at night or in poor vision. IMPORTANT SAFETY PRECAUTIONS! OVERALL Forward/Reverse High/Low speed mode switch 2. Connect the supplied USB charging cable to the charging port of the remote, and then plug into a computer or an adapter. The power indicator for the remote lights red during charging and turns green when fully charged. 3. Check the App or power indicators on the battery compartment to find the power capacity of the skateboard. • 1x Skateboard • 1x T tool 1. Connect the supplied charger to the charging port of the skateboard, and then plug into a standard household outlet. The power indicator on the charger lights red during charging, and turns green when fully charged. 4. Check the power indicators on the remote to find the power capacity of the remote. Horn Battery compartment Signal indicator Power button USB charging port LEDs Color Power Green Full Green 75% Green 50% Red <25% end of their useful life must be given to waste disposal centers specializing in separate collection of waste electrical PLAY YOUR SKATEBOARD Specifications • If in the eyes, rinse thoroughly with cool water. Immediately seek medical attention. • The built-in battery may discharge completely after a long period without use. Recharge the battery before use. 1. Press the power button to turn on/off the skateboard. The headlights turn on. Items Specification Remark 3. Push the Go/Stop switch forward to go, release to stop. Drive Unit 10 A, 200 W BLDC single motor at rear wheels 4. Hold the Go/Stop switch backward to turn on the taillights. Double press the power button on the remote to turn on/off the headlights. Speed Normal Speed mode: ≤18 km/h At 75 Kg loading 2. Press and hold the power button for 3 seconds to turn on/off the remote. 5. Changing the playing mode by Forward/Reverse and High/Low speed switches. NOTE • Taillights beam in normal mode; Flash by automatically detect in stop mode. • Left and right turning indicators will flash and are controlled by Gyroscope automatically when turning direction. High speed mode: ≤25 km/h Endurance Mileage Normal mode: ≤10 km Remote Control BLE 4.0 module connected to Mobile At 75 Kg loading High speed mode: ≤10 km Pedal and brake control Battery Open the App, it will find the skateboard automatically. With the App, you can • Use only the supplied charger and cable for charging. • Charge batteries on a fireproof surface away from flammable items or liquids. • Do not charge inside an automobile, especially while driving. • Follow the instructions for charging. Do not charge longer than recommended. Unplug the USB cable when the battery is charged. PRECAUTIONS Forward/Reverse control APP OPERATIONS • The skateboard should never be left unattended while charging. • Do not subject the device to excessive force, shock, dust, temperature or humidity. LG MG1 Power battery pack (7x 18650 - 3.6 V) (3200 mAh-1S7P) • Do not immerse the device in water. If you spill liquid over it, dry it immediately with a soft, lintfree cloth. • Check the power, light, speed status Size 560 mm x 220 mm x 117 mm • Do not clean the device with abrasive or corrosive materials. • Set the horn sound and light colour Recharge Time 1~1.5 hr • Do not tamper with the device’s internal components. Doing so invalidates the warranty. • Turn on/off the headlights and taillights Wheel Base Diameter: 73 mm • Images shown in this manual may differ from the actual display. PAIR SKATEBOARD WITH REMOTE Weight About 3.9 kg • When disposing of this product, ensure it is collected separately for special treatment. NOTE: The remote and the skateboard are paired in the factory. If a new remote is needed, pair the new remote with the skateboard before using. Board Material Canadian Maple Wood Max Load 100 kg • The contents of this manual may not be reproduced without the permission of the manufacturer. Operation Conditions -10 to 60 C ≤85 % R.H. Storage Condition -20 to 80 0C ≤95 % R.H. 1. Turn off the skateboard and the remote. 2. Pull the Go/Stop switch as far backwards as it will allow. 3. Turn on the remote. The Signal indicator of the remote flashes quickly. 4. Turn on the skateboard. LITHIUM BATTERY SAFETY INSTRUCTIONS 5. Release the Go/Stop switch. The Signal indicator of the remote lights steady. The remote and the skateboard are successfully paired. • Do not burn or bury batteries. Do not puncture or crush. Do not disassemble. • Recycle lithium batteries. Do not dispose of in the trash • If the electrolyte in the cells should get on your skin, thoroughly wash with soap and water. NOTE:The technical specifications for this product and the contents of the user manual are subject to change without notice. NOTE: Features and accessories will not be available in all countries. For more information, please contact your local retailer. To download an electronic version of the user manual, please visit http://global.oregonscientific.com/customerSupport.php. ABOUT OREGON SCIENTIFIC Visit our website www.oregonscientific.com to learn more about Oregon Scientific products. For any inquiry, please contact our Customer Service at info@oregonscientific.com. Oregon Scientific Global Distribution Limited reserves the right to interpret and construe any contents, terms and provisions in this user manual and to amend it, at its sole discretion, at any time without prior notice. To the extent that there is any inconsistency between the English version and any other language versions, the English version shall prevail. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio / TV technician for help. This Class B digital apparatus complies with Canadian ICES-3(B)/NMB-3(B) DECLARATION OF CONFORMITY The following information is not to be used as contact for support or sales. Please call our customer service number (listed on our website at www.oregonscientific.com), or on the warranty card for this product for all inquiries instead. We Name: Oregon Scientific, Inc. Address: Centerpointe Center 5 Centerpointe Drive, Suite 400 Office no. 11 & 19 Lake Oswego, Oregon 97035 Telephone No.: 971-204-0378 declare that the product Product No.: SMS203 Product Name: Huger board Neu Manufacturer: IDT Technology Limited Address: Block C, 9/F, Kaiser Estate, Phase 1, 41 Man Yue St., Hung Hom, Kowloon, Hong Kong EU – DECLARATION OF CONFORMITY Hereby the manufacturer, IDT Technology Limited, declares that the radio equipment type [Huger board Neu (SMS203).] is in compliance with 2014/53/EU Directive. The full text of the EU Declaration of Conformity is available at the following internet address : www.oregonscientific.com COUNTRIES RED APPROVED COMPLIED All EU countries, Switzerland and Norway DISPOSAL INFORMATION FOR USERS Pursuant to and in accordance with Article 14 of the Directive 2012/19/EU of the European Parliament on waste electrical and electronic equipment (WEEE), and pursuant to and in accordance with Article 20 of the Directive 2013/56/EU of the European Parliament on batteries and accumulators and waste batteries. The barred symbol of the rubbish bin shown on the equipment indicates that, at the end of its useful life, the product must be collected separately from other waste. Please note that the batteries/rechargeable batteries must be removed from the equipment before it is given as waste. To remove the batteries/accumulators refer to the specifications in the user manual. Therefore, any products that have reached the and electronic equipment, or given back to the dealer when purchasing a new WEEE, pursuant to and in accordance with Article 14 as implemented in the country. The adequate separate collection for the subsequent start-up of the equipment sent to be recycled, treated and disposal of in an environmentally compatible way contributes to preventing possible negative effects on the environment and health and optimizes the recycling and reuse of components making up the apparatus. Abusive disposal of the product by the user involves application of the administrative sanctions according to the laws in force. Warning changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. NOTE: This device and its antenna(s) must not be coÿlocated or operation in conjunction with any other antenna or transmitter.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No XMP Toolkit : Adobe XMP Core 5.2-c003 61.141987, 2011/02/22-12:03:51 Create Date : 2017:04:10 11:34:54+08:00 Metadata Date : 2017:04:10 11:34:57+08:00 Modify Date : 2017:04:10 11:34:57+08:00 Creator Tool : Adobe InDesign CS5.5 (7.5.2) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 3939 bytes, use -b option to extract), (Binary data 4317 bytes, use -b option to extract) Instance ID : uuid:3fc7bfaf-3dde-2744-ab11-35d8ae80485f Document ID : xmp.did:34D2904819206811808391988194D5E3 Original Document ID : xmp.did:34D2904819206811808391988194D5E3 Rendition Class : proof:pdf History Action : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:34D2904819206811808391988194D5E3, xmp.iid:39D2904819206811808391988194D5E3, xmp.iid:3AD2904819206811808391988194D5E3, xmp.iid:6A0F6A0E1B206811808391988194D5E3, xmp.iid:6F0F6A0E1B206811808391988194D5E3, xmp.iid:740F6A0E1B206811808391988194D5E3, xmp.iid:BCC2B5701B206811808391988194D5E3, xmp.iid:FB7F1174072068118A6DA1B89D52A77F, xmp.iid:00801174072068118A6DA1B89D52A77F, xmp.iid:518522090B2068118A6DA1B89D52A77F, xmp.iid:528522090B2068118A6DA1B89D52A77F, xmp.iid:23C58692072068118C14AD017DB90559, xmp.iid:29C58692072068118C14AD017DB90559, xmp.iid:4D55294C082068118C14AD017DB90559, xmp.iid:F2A8BD01112068118C14AD017DB90559, xmp.iid:F8A8BD01112068118C14AD017DB90559, xmp.iid:2988CC30132068118C14AD017DB90559, xmp.iid:7C5CF544132068118C14AD017DB90559, xmp.iid:825CF544132068118C14AD017DB90559, xmp.iid:91901DA7132068118C14AD017DB90559, xmp.iid:97901DA7132068118C14AD017DB90559, xmp.iid:CC05F8DB132068118C14AD017DB90559, xmp.iid:D205F8DB132068118C14AD017DB90559, xmp.iid:5944A20C142068118C14AD017DB90559, xmp.iid:6044A20C142068118C14AD017DB90559, xmp.iid:607D8162152068118C14AD017DB90559, xmp.iid:C0E0EF00192068118C14AD017DB90559, xmp.iid:C7E0EF00192068118C14AD017DB90559 History When : 2017:03:30 11:27:30+08:00, 2017:03:30 11:35:54+08:00, 2017:03:30 11:35:54+08:00, 2017:03:30 11:40:12+08:00, 2017:03:30 11:40:41+08:00, 2017:03:30 11:41:17+08:00, 2017:03:30 11:42:57+08:00, 2017:03:31 11:58:33+08:00, 2017:03:31 11:58:53+08:00, 2017:03:31 12:24:12+08:00, 2017:03:31 12:24:39+08:00, 2017:04:10 09:28:02+08:00, 2017:04:10 09:28:13+08:00, 2017:04:10 10:34:58+08:00, 2017:04:10 10:35:34+08:00, 2017:04:10 10:50:44+08:00, 2017:04:10 10:51:12+08:00, 2017:04:10 10:51:46+08:00, 2017:04:10 10:52:59+08:00, 2017:04:10 10:54:31+08:00, 2017:04:10 10:55:25+08:00, 2017:04:10 10:55:59+08:00, 2017:04:10 10:56:40+08:00, 2017:04:10 10:57:21+08:00, 2017:04:10 11:03:20+08:00, 2017:04:10 11:06:54+08:00, 2017:04:10 11:32:49+08:00, 2017:04:10 11:34:06+08:00 History Software Agent : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata Doc Change Count : 237 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 2 Creator : Adobe InDesign CS5.5 (7.5.2)EXIF Metadata provided by EXIF.tools