IDTECK LX006 Fingerprint Recognition Proximity Reader User Manual
ID-Teck Co Ltd Fingerprint Recognition Proximity Reader Users Manual
IDTECK >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2988548 |
| Application ID | 6z22OJofL/BhQbmfvyGCXQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 114.83kB (1435313 bits) |
| Date Submitted | 2016-05-12 00:00:00 |
| Date Available | 2016-05-12 00:00:00 |
| Creation Date | 2016-05-02 18:32:46 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2016-05-03 11:36:37 |
| Document Title | Users Manual |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | (주)ì•„ì´ë””-í…Œí¬ ì—°êµ¬ì†Œ 연구소장 ìœ ëª…í˜¸ |
User’s Manual LX006 Fingerprint Identification Proximity Reader TABLE OF CONTENTS 1. IMPORTANT SAFETY INSTRUCTIONS .......................................................................................................................... 4 2. FEATURES ....................................................................................................................................................................... 5 3. SPECIFICATION .............................................................................................................................................................. 7 4. IDENTIFYNG SUPPLIED PARTS .................................................................................................................................... 9 5. PRODUCT EXPLANATION ............................................................................................................................................ 10 5.1 PANEL LAYOUT .................................................................................................................................................. 10 5.2 CONNECTION LAYOUT...................................................................................................................................... 10 5.3 COLOR CODED & WIRING TABLE .................................................................................................................... 11 6. INSTALLATION TIPS & CHECK POINTS ...................................................................................................................... 12 6.1 CHECK POINTS BEFORE INSTALLATION ........................................................................................................ 12 6.1.1 CABLE SELECTION ................................................................................................................................ 12 6.1.2 RECOMMENDED CABLE TYPE AND PERMISSIBLE LENGTH OF CABLE ......................................... 12 6.1.3 READER CONNECTION ......................................................................................................................... 12 6.2 CHECK POINTS DURING INSTALLATION ......................................................................................................... 13 6.2.1 TERMINATION RESISTOR ..................................................................................................................... 13 6.2.2 HOW TO CONNECT TERMINATION RESISTORS................................................................................. 14 6.2.3 GROUNDING SYSTEM FOR COMMUNICATION CABLE ...................................................................... 14 7. INSTALLATION OF THE PRODUCT .............................................................................................................................. 15 7.1 WALL MOUNT DRAWING ................................................................................................................................... 15 7.2 INSTALLATION OF WALL MOUNT ..................................................................................................................... 15 7.3 SYSTEM INITIALIZATION ................................................................................................................................... 16 7.4 COMMUNICATION ID SETTING ......................................................................................................................... 17 7.5 WIRING ............................................................................................................................................................... 18 7.5.1 WIRING LAYOUT ..................................................................................................................................... 18 7.5.2 POWER WIRING ..................................................................................................................................... 18 7.5.3 INPUT WIRING ...................................................................................................................................... 19 7.5.4 OUTPUT CONNECTION ......................................................................................................................... 20 7.5.5 EXTERNAL READER CONNECTION ..................................................................................................... 21 8. COMMUNICATION ......................................................................................................................................................... 22 ............................. 22 8.1 RS232 COMMUNICATION PORT CONNECTION ................................................................................... 8.2. RS485 COMMUNICATION PORT CONNECTION ............................................................................................. 22 8.2.1 RS485 COMMUNICATION PORT CONNECTION (SINGLE CONNECTION) ........................................ 22 8.2.2 RS485 COMMUNICATION PORT CONNECTION (MULTIPLE CONNECTION) .................................... 23 8.3 TCP/IP COMMUNICATION PORT CONNECTION ............................................................................................. 24 9. BASIC SETTING ............................................................................................................................................................ 25 9.1 INITIALIZATION OF LX006 ................................................................................................................................. 25 9.2 COMMUNICATION ID SETTING ......................................................................................................................... 25 10. OPERATION MODE ..................................................................................................................................................... 26 10.1 MASTER CARD REGISTRATION MODE ......................................................................................................... 26 10.1.1 MASTER CARD REGISTRATION ......................................................................................................... 26 10.1.2 MASTER CARD CHANGE..................................................................................................................... 26 10.1.3 MASTER CARD FUNCTION. ................................................................................................................ 26 10.2 REGISTRATION / DELETION MODE ............................................................................................................... 26 10.2.1 REGISTRATION MODE FUNCTION ..................................................................................................... 26 10.2.2 USER CARD REGISTRATION .............................................................................................................. 26 10.2.3 USER CARD DELETION ....................................................................................................................... 28 10.3 READER MODE ................................................................................................................................................ 28 10.3.1 READER MODE FUNCTION. ................................................................................................................ 28 10.3.2 AUTHORIZATION .................................................................................................................................. 28 10.4 READER INDICATOR ....................................................................................................................................... 29 10.5 DEFAULT SETTINGS ........................................................................................................................................ 30 11. OUTPUT FORMAT ....................................................................................................................................................... 31 11.1 WIEGAND OUTPUT (DEFAULT) ....................................................................................................................... 31 11.2 ABA TRACK Ⅱ (SELECTABLE USING THE SOFTWARE) .............................................................................. 31 11.3 OUTPUT MODE................................................................................................................................................. 32 11.3.1 NORMAL OUTPUT MODE..................................................................................................................... 32 11.3.2 EXTENSION OUTPUT MODE (SET BY APPLICATION SOFTWARE) ................................................. 33 12. APPENDIX .................................................................................................................................................................... 33 13. FCC REGISTRATION INFORMATION ......................................................................................................................... 37 14. WARRANTY POLICY AND LIMITATION OF LIABILITY ............................................................................................... 38 15. HOW TO MAKE RMA REQUEST (AFTER SALES SERVICE) .................................................................................... 39 1. IMPORTANT SAFETY INSTRUCTIONS The description below is to keep user’s safety and prevent any product damage. Please fully read these instruction and use the product properly. Danger: This symbol indicates that incorrect handling of the product may result in serious injury or death. Warning: This symbol indicates that incorrect handling of the product may result in injury or property damage. Cautions about power - Only use the standard voltage (DC +12V/ 350mA). (When supplying DC power to the device, we recommend that you use the adapter or SMPS that come standard with the device.) - If the product emits smoke or smells, stop using the product. Unplug the product from DC power source and contact nearest service center. Cautions about installation - Do not install the product in humid, dust (metallic dust) and sooty place. - Do not install the product in a place subject to high/ low temperature or high humidity - Do not install the product with tools such as driver in hand when power has been supplied. Cautions about usage - Do not drop liquid like water and give a shock severely. - Do not place magnetic objects near the product. - Do not replace the wiring cables installed by experts. - Do not use the product near direct sunlight and heating apparatus. - If you want to relocate the installed product, turn power off and then move and reinstall it. - Do not use the product near flammable spray or objects. - Do not disassemble, repair or modify the product by yourself. If the product needs service or repair, contact nearest service center. - If liquid has been spilled on the product, unplug it and contact nearest service center. Cautions about cleaning - Do not clean the product with water. Clean gently with dry cloth or towel. - Do not use chemicals such as benzene, thinner or acetone for cleaning. 2. FEATURES Fingerprint Recognition Proximity Reader The LX006 is a Fingerprint and Proximity Reader compatible with existing proximity readers. The LX006 has a built-in proximity reader and fingerprint module so that the access is only allowed when the personal ID and fingerprint are authorized and this integrated system gives you high and reliable security. The LX006 can register up to 200,000 User IDs and 1,000(default)/ 2,000(optional) / 4,000(optional) fingerprint users. Easy Installation LX006 can be easily installed on flat wall or the door frame. 1:1 Verification and 1:N Identification User can select operation mode between 1:1 Verification and 1:N Identification for his convenience. RF Only Mode and RF + FINGER Mode The LX006 has two operation modes when it is operated as a reader. - RF Only Mode In the RF Only Mode, only card authorization is needed to grant access. If a card is authorized, the corresponding card ID will be transmitted to the controller. - RF + FINGER Mode In the RF + Finger Mode, both card and fingerprint authorization is needed to grant access. If a fingerprint is authorized, the corresponding card ID will be transmitted to the controller. If user’s fingerprint is not registered, the mode is automatically working as ‘RF Only’ Network Communication The LX006 can establish network communication via RS232 / RS485 and built in TCP/IP internal module. Card Number Output Format When a fingerprint is authorized, the corresponding card number is transmitted to the controller via 26/34Bit (SR) Wiegand or ABA Track II according to the output type setting. It is set by application software. Card Number Input Format The LX006 receives the card number from the external reader while the LX006 contains a built-in proximity reader inside. The LX006 receives the card number in 8bit Burst or 26bit Wiegand or ABA Track II format. It is set by application software. User Registration and Deletion Using Master Card User can register and delete IDs using Master Card without application software. Also the master card is used to toggle the LX006 between the reader mode and the registration/deletion mode. Firmware Upgrade Use can upgrade firmware using application software Voice Message Generation and Tamper switch Voice Message notices users whether the LX006 is normally operating or not. When someone has broken the installed LX006 by force, Temper Switch transmits corresponding data to the Host PC to prevent theft. Plenty of Application Software There are plenty of application software for LX006, STARWATCH STANDARD, STARWATCH ENTERPRISE, STARWATCH DUAL PRO I, II, STARWATCH iTDC PRO I, II, STARWATCH LX ACCESS PRO II, STARWATCH ENROLLMENT PRO. If you use LX006 which has linked with the third party access controller, visit IDTECK’s homepage (www.IDTECK.com) and download STARWATCH FINGERPRINT ENROLLMENT PRO via download center. 3. SPECIFICATION Model LX006 CPU 32bit ARM9 and Dual 8bit Microprocessor 2MByte Flash Memory for 1000 Fingerprints 6MByte for 2000/4000 Fingerprints 8MByte SDRAM 128KByte Flash Memory 256KByte Flash Memory 32KByte SRAM 10,000 User IDs 1,000 / 2,000 / 4,000 Fingerprint Users 26Bit Wiegand, ABA Track II Fingerprint Program Memory Module Data Memory Memory Program Memory Controller Data Memory User ID Fingerprint User Reader Data Output Format Reading Time (Card) 30ms Verification / Identification Time Power / Current Less than 1sec. / Less than 2sec. DC +12V / Max.290mA 1 port (26bit Wiegand, 4/8bit Burst for PIN, ABA Track II) RS232 / RS485 (Max.32ch) TCP/IP 57,600bps (Recommended)/9,600bps/ 19,200bps/38,400bps (Selectable) 3ports(LED, Buzzer, Application Mode Control ) 3ports(Error-Output, OK-Output, Tamper-Output) (Open Collector Output Format) 3 Array LED Indicators (Red, Green and Yellow) Piezo Buzzer -15 to +60C (+5 to +140F) -35 to + 65C (-31 to +149F) 10% to 90% Relative Humidity Non-condensing Black, Red, Gray, Silver, Dark Gray, Gold and Gold with Black / Polycarbonate 230g(0.51lbs)/ 69mm x 127mm x 43mm FCC, CE, KC, ROHS English(Default), (Other Language Support Available) External Reader Port Communication Baud Rate Input Port Output Port LED Indicator Beeper Operating Temperature Operating Humidity Fingerprint Module RF Reader Color / Material Weight / Dimension (W x H x T) Certification Language Read Range Model Read Range IDC80 IDC170 Maximum of 4 inches LX006 (10cm) Fingerprint Module Specification Resolution 500dpi Capture Image Size 356 X 292 pixels Extraction Image Size 248 X 292 pixels Sensing Area 12.7 X 14.9mm Scanner High Quality Optical Sensor FAR(False Acceptance Ratio) 0.001% FRR(False Reject Ratio) 0.1% ESD(Electro Static Discharge) ±8KV Verification Time Less than 1sec. Identification Time Less than 2sec. 4. IDENTIFYNG SUPPLIED PARTS Please unpack and check the contents of the box. If any of flowing items is missing, please contact nearby contributor. (Optional accessories, if purchased, may be included in the package.) LX006 (1 ea) User’s Manual (1 Copy) Wall Mount (1 ea) Screw 3 X 30 mm – 2 ea 3 X 6 mm – 1 ea 3.5 X 12 mm – 2 ea Plastic Anchor 6 x 30 mm – 2 ea 12v dc adapter (option) (DVE DSA-60W-12 1) Cable 300mm 2P – 1 ea 300mm 6P – 1 ea 300mm 8P – 1 ea 150mm 8P – 1 ea Master Card (1 ea) 5. PRODUCT EXPLANATION 5.1 PANEL LAYOUT Status LED Fingerprint Scanner Proximity Reader Speaker (Figure: Panel Codes) 5.2 CONNECTION LAYOUT Tamper SW CON-4 CON-3 CON-2 DIP SW CON-1 (Figure: Connecter Arrangement) 10 5.3 COLOR CODED & WIRING TABLE I/O PORT NAME SIGNAL NAME WIRE COLOR CON-1: Power (2PIN Connector) Power (+12V) DC +12V Red Ground GND (-) Black CON-2: In/Output (6PIN Connector) EX Input Wiegand DATA0 EX-DATA0 ABA Track II Data In Pink EX Input Wiegand DATA1 EX-DATA1 ABA Track II Clock In Cyan NC Brown NC Blue RS4 85 RS485-A(+) RS485-A(+) Yellow RS485-B(-) RS485-B(-) Gray CON-3: In/Output (8PIN Connector) Wiegand DATA 0 DATA-0 ABA Track II Data Out Green Wiegand DATA 1 DATA-1 ABA Track II Clock Out White ERROR SIGNAL OUT ERROR SIGNAL OUT ABA Track II CLS Out Orange OK SIGNAL OUT OK SIGNAL OUT Orange with Black stripe TAMPER OUT TAMPER OUT Purple EX_LED_CONTROL EX_LED_CONTROL Blue with White stripe EX_BUZZER_CONTROL EX_BUZZER_CONTROL White with Red stripe EX_SYS_CHANGE_IN EX_SYS_CHANGE_IN Gray with Red stripe CON-4: TCP/IP (8PIN Connector) RJ45 Cable Connection 11 6. INSTALLATION TIPS & CHECK POINTS Please refer to information below to stably operate the LX006. 6.1 CHECK POINTS BEFORE INSTALLATION 6.1.1 CABLE SELECTION POWER POWER (Figure: System configuration) 6.1.2 RECOMMENDED CABLE TYPE AND PERMISSIBLE LENGTH OF CABLE No Cable specification Description LX006 Power (DC+12V) DC Power -> LX006 *2 RS232 Cable converter->Host P.C. Belden #9409,18 AWG 2 conductor, unshielded Belden #9829, 24 AWG 2-twisted pair, shielded RS485 Cable Belden #9829, 24 AWG LX006 -> LX006 2-twisted pair, shielded LX006 -> Converter * Thicker wires are required if you connect the reader with high current consumption. Maximum distance 3m 15m 1,200m 6.1.3 READER CONNECTION If you install the reader in a long distance between the ACU and the reader, you should be aware there could be voltage drop between ends of GND wire. For example, if you connect a reader with 100mA current consumption at 100m distance (assume to using DC resistance of cable of 100Ω/100m) and the reader power is supplied from the ACU, the voltage drop of the GND wire will be 1V. In this case, the Wiegand data signal cannot be measured lower than 1V. 12 The most of ACU is capturing the signal by the voltage level of data input. 1V is the critical point whether the ACU read the data logic “1” or logic “0” therefore the reader output cannot be read correctly from the ACU. There will be two methods to reduce the voltage drop and ACU can read data correctly. Reduce the DC resistance of GND wire; Using thick cable or add more wires to GND wire in parallel. If you connect 4 wires in parallel for GND, the DC resistance of GND wire will be reduced to 1/4 of single wire. Use separate power for the reader; Disconnect +12V wire from the ACU and connect external power supply to the reader nearby. There will be no current flow through the GND wire and no voltage drop between ends of GND wire. ACU (Figure: When Sharing a Single Power Supply for Multiple Units) POWER ACU (Figure: When Using a Separate Power Supply for the LX006) 6.2 CHECK POINTS DURING INSTALLATION 6.2.1 TERMINATION RESISTOR Termination resistors are used to match impedance of the network to the impedance of the transmission line being used. When impedance is mismatched, the transmitted signal is not completely absorbed by the receiver and a portion of signal is reflected back into the transmission line. The decision whether or not to use termination resistors should be based on the cable length and data rate used by the communication system. 13 6.2.2 HOW TO CONNECT TERMINATION RESISTORS (Figure: Termination resistors for 2 wire RS485 communication system) 6.2.3 GROUNDING SYSTEM FOR COMMUNICATION CABLE We recommend proper grounding system on the communication cable. The best method for grounding system is to put the shield wire of the communication cable to the 1 st class earth grounding; however it is not so easy to bring the earth ground to the communication cable and also the installation cost is raised. There will be three grounding point where you can find during installation; 1, Earth Ground 2. Chassis Ground 3. Power Ground The most important point for grounding system is not to connect both ends of shield wires to the grounding system; in this case there will be a current flow through the shield wire when the voltage level of both ends of shield wire is not equal and this current flow will create noise and interfere to communications. For the good grounding, we recommend you to connect ONLY one end of shield wire of communication cable to grounding system; If you find earth ground nearby, connect one end of shield wire to earth ground; If you do not have earth ground nearby, find chassis ground and connect one end of shield wire to chassis ground; If you do not find both earth ground and chassis ground, then connect one end of shield wire to power ground. (GND of LX006). Note that if the chassis ground is not properly connected to the earth and floated from the ground level, then grounding to the chassis ground will make the worst communication; in this case we recommend you to use power ground instead of chassis ground. (Figure: Grounding system) 14 7. INSTALLATION OF THE PRODUCT 7.1 WALL MOUNT DRAWING (Unit: mm) (Figure: Wall Mount) 7.2 INSTALLATION OF WALL MOUNT - Place the Wall Mount on the desired position on the wall and mark the locations of the 2 screw holes. - Drill a hole in the center of the Wall Mount for cable. - Take out the cable from the center of hole. - Wire cable to four connecters and then perform initialization and set communication ID. - By using of one screw on the bottom, fix the Wall Mount with LX006. 15 7.3 SYSTEM INITIALIZATION Initialize the system using the DIP switch on the rear of the product. 1. Disconnect the power supply. 2. Position the DIP switch on the rear of the product to ON (upside) and apply power to the product. 3. The product sounds a beep once with a voice message, and proceed with the hardware initialization process. 4. When the initialization is done, the product sounds a beep three times with a completion message output. The product keeps sounding the beep until you change the communication address. 5. Use the DIP switch to specify the BOARD ID. Refer to “7.4 COMMUNICATION ID SETTING”. 6. You must specify the communication address and register the master ID. Cautions • After fixing the LX006 on the wall mount, you can’t initialize the system by this procedure. But you can initialize it through Application Software • If you initialize the system using software, all data except for the IP setting returns to the default. • If you initialize the hardware system, all data settings return to the factory default. (including IDs, fingerprint data, master ID, card number output format, IP) • If the communication address is set to 255, the initialization process gets started immediately 16 7.4 COMMUNICATION ID SETTING LX006 can upload/ download user’s information by application software and adjust setting values. Communication ID is the unique communication address to recognize each LX006 in the software so each communication ID on the same communication loop must not be duplicated. There is 8-bit DIP switch on the back of LX006 for communication ID setting and each channel of DIP switch has assigned address values. The communication ID is calculated by the sum value of each bit set to “ON” position. Communication ID can be set from ‘0’ to ‘255’. Refer to examples below to set communication ID. Cautions Each communication ID in the same communication loop must not be duplicated. If the same communication IDs are on the loop, it may cause communication error. Example 1 Example 2 Example 3 1+2 = 3 (Communication ID = 3) 4+32 = 36 (Communication ID = 36) 128= 128 (Communication ID = 128) (Figure: Communication ID Setting Example) 17 7.5 WIRING 7.5.1 WIRING LAYOUT Controller Buzzer Control LED Control System Mode Control Wiegand White with Red stripe Blue with White stripe Gray with Red stripe ABA Track II Orange with Black stripe Authentication input Authentication error input DATA1 DATA0 DC12V GND(-) TAMPER RS485-A(+) RS485-B(-) Orange White Green CLS CLK DATA Red Black Purple Pink Yellow Gray Cyan RJ45 8bit Burst 26bit/34bit(SR) HUB Wiegand DATA1 DATA0 DC +12V GND(-) External reader 7.5.2 Power Wiring 1. Connect +12V (+) wire of Power to Red wire of LX006 2. Connect GND (-) wire of Power to Black wire of LX006 Cautions You can use separate power supplies for the LX006 and the Controller; however, the GND(-) wire must be connected to the Black wire, in any case. 18 7.5.3 INPUT WIRING External LED Control Connection Connect the LED Control Input wire (Blue wire with White stripe) to the NO port of controller relay output, and GND to the COM port. Set I/O of the controller; then you can control tuning on and off the green LED. While the LED control is working, the green LED stays on. The controller can use the I/O setting to set the LED controller so that it displays the additional LED status for authorized/unauthorized access. For more information about the I/O setting of the controller, refer to the controller’s user manual. External Buzzer Control Connection Connect the Buzzer Control Input wire (White wire with Red stripe) to the NO port of controller relay output, and GND to the COM port. Set I/O of the controller; then you can generate beep sound. While the buzzer control is working, the product keeps sounding beep. The controller can use the I/O setting to set the buzzer controller so that it sounds the additional beep for authorized/unauthorized access. For more information about the I/O setting of the controller, refer to the controller’s user manual. External Input Device Connection (System Operating Mode Change through External Input) Connect the System Mode Control wire (Gray wire with Red stripe) to the NO port of controller relay output, and GND to the COM port. Set I/O of the controller; then you can control the system mode. While the system mode is controlled, RF Only mode is operated. With I/O or time schedule setting, the controller can switch system operation mode in a specific time section. For more information about the I/O setting of the controller, refer to the controller’s user manual. Buzzer Control White with Red stripe LED Control Blue with White stripe System Mode Control Gray with Red stripe GND 12V POWER (Figure: Input Connection) 19 7.5.4 OUTPUT CONNECTION Wiegand DATA Output Connection 1. Connect Wiegand Data 0 wire (Green wire) to Wiegand Data 0 terminal of the Controller. (Used for DATA when ABA Track II is output) 2. Connect Wiegand Data 1 wire (White wire) to Wiegand Data 1 terminal of the Controller. (Used for CLOCK when ABA Track II is output) 3. The GND(-) wire must be connected between the LX006 and the Controller. Access Error Signal Connection - Connect the Access Error Signal wire (Orange wire) to the Access Error Input terminal of the Controller. (Used for CLS when ABA Track II is output) Access OK Signal Connection - Connect the Access OK Signal wire (Orange wire with Black stripe) to the Access OK Input terminal of the Controller. (Not used when ABA Track II is output) OK Signal Out (Orange with Black stripe) Error Signal Out(Orange) ACU )DATA1(White) )DATA0(Green) 12V GND POWER (Figure: Wiegand Output Connection) CLS (Orange) CLOCK(White) ACU )DATA(Green) 12V GND(-) POWER (Figure: ABA Track II Output Connection) 20 7.5.5 EXTERNAL READER CONNECTION Proximity Reader Connection 1. Connect the DC+12V wire of Power Supply to (+) wire of reader. 2. Connect the GND(-) of Power Supply to (-) wire of reader 3. Connect the Wiegand Data 0 wire of the External Reader to the Wiegand Input Data 0 wire of LX006 (Pink wire). 4. Connect the Wiegand Data 1 wire of the External Reader to the Wiegand Input Data 1 wire of LX006 (Cyan wire). 5. The GND(-) wire must be connected between the external and the LX006. Compatible Reader: LX006: Standard 26bit Wiegand proximity reader Standard 26bit Wiegand + 4/8bit burst proximity/ keypad reader LX006SR: Standard 34bit Wiegand proximity reader Standard 26bit Wiegand + 4/8bit burst proximity/ keypad reader ACU POWER (Figure: External Reader Connection) 21 8. COMMUNICATION 8.1 RS485 COMMUNICATION PORT CONNECTION 8.1.1 RS485 COMMUNICATION PORT CONNECTION (SINGLE CONNECTION) An RS-485/RS-232 converter is required to connect serial communication RS485 between the LX006 Main Unit and the Host Computer. - Connect RS485 - RTX (+) (Yellow) wire of Main Unit to RS485-A of Converter. - Connect RS485 - RTX (-) (Gray) wire of Main Unit to RS485-B of Converter. - Plug the RS232 9-pin connector of INC300 converter into COM1 or COM2 Port of Computer. - Install and run the application software. Gray Wire Yellow Wire (Figure: RS485 Connection between LX006 and Host PC) * The maximum of cable length can be shortened depending on communication speed, the type of communication cable and cable installing environment. 22 8.1.2 RS485 COMMUNICATION PORT CONNECTION (MULTIPLE CONNECTION) RS485/RS232 converter is required to use RS485 communication between multiple LX006s and a host computer. Please follow the following instructions. First, you have to connect all RS485 port of all LX006s in parallel. (Maximum of 255) - Connect RS485-A(+) (Yellow) of one LX006 to RS485–A(+) (Yellow) of another LX006. - Connect RS485-B(-) (Gray) of one LX006 to RS485–B(-) (Gray) of another LX006. - Set different COMM ID for each LX006. Second, you have to connect one of RS485 port of LX006 to RS485/RS232 converter. - Connect RS485-A(+) (Yellow) of one LX006 to RS485-A port of the Converter. - Connect RS485-B(-) (Gray) of one LX006 to RS485-B port of the Converter. - Plug in the RS485/RS232 9-pin connector of the converter to the COM1 or COM2 Port of the PC. - Install and run LX006 Application Software. Gray Wire Yellow Wire (Figure: Multiple Connection of LX006 with RS485) 23 8.2 TCP/IP COMMUNICATION PORT CONNECTION For TCP/IP communication, external cable is required to connect to CON4 (8PIN connecter). Please follow the following instructions. 1. Connect the LAN cable of the network system to the RJ45 jack of the LX006. 2. Install and run the Application Software. HUB RJ45 RJ45 RJ45 RJ45 (Figure: TCP/IP Communication connection of LX006) 24 9. BASIC SETTING 9.1 INITIALIZATION OF LX006 - Initialization should be performed before mounting the LX006 to the Wall Mount. - If you need to initialize LX006 after installing it on the wall, you can use the Application Software to do that. (Refer to the Software Manual for more information.) - For more information about how to initialize the LX006, refer to ‘7.3 SYSTEM INITIALIZATION’. Cautions If the Controller is initialized, all data stored in the Controller will be cleared and the default setting values (factory setting values) will be reloaded. Therefore, the Initialization should be performed by authorized person only. It is strongly recommended to upload all events data before initialization. 9.2 COMMUNICATION ID SETTING - The LX006 can upload or download user’s fingerprint data using the Application Software. You can also customize the settings of LX006 for your needs. - There is one 8 channel DIP switch on the back of FGR006/SR unit for communication ID setting. Each channel of DIP switch has assigned address value. The communication ID is calculated by the sum value of each switch set to “ON” position. Communication ID can be set from ‘000’ to ‘255’. Please refer to the ‘7.4 COMMUNICATION ID SETTING’ for more details. 25 10. OPERATION MODE 10.1 MASTER CARD REGISTRATION MODE While the LX006 is operating in the Master Card Registration Mode, the Red and Green LEDs are lit. 10.1.1 MASTER CARD REGISTRATION The card presented to the LX006 for the first time after initialization becomes the master card. ※ NOTE: Fingerprint verification is not used for the Master Card. After the Master Card is recognized, the Green LED blinks with 3 beeps. 10.1.2 MASTER CARD CHANGE You can change the registered Master Card after system initialization. ※ CAUTION : If you initialize the system, all user data will be deleted. Alternatively, you can change the Master Card using the application software. (Using the application software keeps the user data unchanged.) 10.1.3 MASTER CARD FUNCTION. The Master Card is used to toggle the LX006 between the Reader Mode and the Registration Mode. ※ For example, If you present the master card in the Reader Mode, the LX006 shifts to the Registration Mode. If you present the master card in the Registration Mode, the LX006 shifts to the Reader Mode. 10.2 REGISTRATION / DELETION MODE While the LX006 is operating in the Registration/Deletion Mode, the Yellow and Green LED blink. 10.2.1 REGISTRATION MODE FUNCTION In the Registration Mode, you can register new user cards or delete registered user cards. - If you present a registered user card, it will be removed from the LX006. (4 beeps) - If you present an unregistered user card, it will be newly registered to the LX006. (3 beeps) - If fingerprint registration is failed, only card ID is registered then it works as RF Only mode. 10.2.2 USER CARD REGISTRATION 1. Present the Master Card to the LX006. 26 2. Yellow and Green LED indicators blink. 3. Present the Proximity Card you want to delete to the LX006. 4-1. RF + FINGER MODE: After presenting the user card you want to register, you should enter the desired fingerprint twice. Follow the steps below to register a new user card; - Present the proximity card to the LX006. - Place the fingerprint on the fingerprint scanner while red light is illuminated from it - Lift the fingerprint up when the red light from the scanner turns off. - Place the fingerprint on the fingerprint scanner once again while the red light is illuminated again. - 3 beeps will be generated if the registration is successfully completed. If the fingerprint registration is not successful, only Card ID is registered then beep sound is generated 3 times. - If you want to register more user cards, repeat the steps above. - If you want to finish registration process, present the Master Card to return to the Reader Mode. 4-2. RF Only: If you’d like to register a new user card without use of fingerprint, don’t place the fingerprint on the fingerprint scanner and wait until the red light from the scanner turns off automatically. -Just present the user card you want like to register. -After the registration is successfully completed, you’ll hear 3 beeps. If the registration is not successful, you’ll hear only 2 beeps. -If you’ want to register more user cards, repeat the procedure above. Or, if you’d like to finish registration process, present the Master Card to return to the Reader Mode (Figure: Correct placement of fingerprint) 27 10.2.3 USER CARD DELETION To delete registered user cards, follow steps below; 1. Present the Master Card to the LX006. 2. Yellow and Green LED indicators blink. 3. Present the Proximity Card you want to delete to the LX006. 4. After the deletion is successfully completed, you’ll hear 4 beeps. If the deletion is not successful, you’ll hear 2 beeps. 5. If you want to delete more user cards, repeat the steps above. 6. To finish the user card deletion process, present the Master Card to return to the Reader Mode. 10.3 READER MODE While the LX006 is operating in the Reader Mode, the Red LED is lit. 10.3.1 READER MODE FUNCTION. In the Reader Mode, the LX006 authorizes or denies users who attempt access by presenting their cards. - If a user is authorized, the LX006 transmits the User ID to the controller. - If a user fails to be authorized, the LX006 transmits the error signal to the controller. (The error signal is not generated when using ABA Track II format.) 10.3.2 AUTHORIZATION If the LX006 is operating in the RF-Only Mode or the User Card is registered as an RF-Only mode card, 1. Present the registered card to the LX006. 2. If the card is authenticated, a long beep will be generated and the Green LED will be lit. If the card fails to be authenticated, the LX006 output the user ID information according to the output format setting. If the LX006 is operating in the RF+FINGER Mode and the User Card is registered as an RF+FINGER mode card, 1. Present the registered card to the LX006. 2. After the card is recognized, the fingerprint scanner emits red light. 3. Place the registered fingerprint on the scanner. 4. If the fingerprint is successfully verified, a long beep will be generated and the Green LED will be lit. The User ID will be transmitted according to the output format setting. 5. If the fingerprint fails to be verified, the buzzer will generate 2 short beeps and the Yellow LED will blink twice. Also, an Access Error Signal output (Low Active) will be generated for 500ms. (The 28 error signal is not generated when using ABA Track II format.) If the card hasn’t yet been registered, 1. The buzzer generates 2 short beeps and the Yellow LED blinks twice to indicate that the presented card is unregistered or deleted. 2. When an unregistered card is presented or a fingerprint is not verified, an Access Error Signal output (Low Active) will be generated for 500ms. (The error signal is not generated when using ABA Track II format.) 10.4 READER INDICATOR LED BEEP VOICE MESSAGE WELCOME TO ACESS CONTROL SYSTEM SYSTEM INITIALIZED STATUS Power is applied and the LX006 is booting up. The initialization has been finished. REGISTRATION MODE MASTER ID REGISTRATION MODE In the status of system initialize. The card recognized in this status, it becomes Master card. REGISTRATION AND DELETION MODE, User card registration/deletion is available PRESENT A CARD BEEPS BEEPS BEEPS BEEPS ID REGISTERED User card registration successfully completed FINGERPRINT REGISTERED FINGERPRINT REGISTRATION FAILED, PLEASE TRY AGAIN User card/Fingerprint registration successfully completed User card/Fingerprint registration is failed User card/Fingerprint deletion successfully ID DELETED completed READER MODE 1 BEEP BEEPS BEEPS The LX006 is in its normal status, waiting for a READER MODE User Card to be presented. ACCESS GRANTED Authentication completed ACCESS DENIED, Authentication failed PLEASE TRY AGAIN ID UNREGISTERED Unregistered person 29 10.5 DEFAULT SETTINGS The initialization before installation restores the default values (factory settings) of the LX006. For desired applications, you may adjust or customize the settings via the Application Software. The default values for the basic settings are as follows; 1. Operating Mode: RF + FINGER 2. Fingerprint Registration: 1 ID 1 Finger Two Template 3. Output Format: 26bit Wiegand/34bit Wiegand(SR) 4. Input Format: 26bit Wiegand/34bit Wiegand(SR) 5. Output Mode: Normal Mode 6. Adaptive Mode: Disabled 7. High Security Mode: Enabled 8. Voice Volume: 3 30 11. OUTPUT FORMAT 11.1 WIEGAND OUTPUT (DEFAULT) Data format (26-bit) Bit 1 / Bit 1: From Bit 2 to Bit 13 / From even parity Bit 2 to Bit 17 Bit 2 to Bit25 / Bit 2 to Bit33: 3-byte ID number / 4-byte ID number Bit 26 / Bit 34: From Bit 14 to Bit 25 / From odd parity Bit18 to Bit 33 Output Timing 11.2 ABA TRACK Ⅱ (SELECTABLE USING THE SOFTWARE) Data format ID number (00000~65535) Facility Code (00000~00255)-LX006 (00000~65535)-LX006SR Low bit first, odd parity last Start Character (11010 Hex ‘B’) Zero bit (10bit) 31 LRC Zero bit Output timing CP CLK Data 1240us 940us (RD1) 6000us 1544us (RD0) 11.3 OUTPUT MODE 11.3.1 NORMAL OUTPUT MODE User ID / Fingerprint authorized User ID unregistered/ Fingerprint error 32 6000us 11.3.2 EXTENSION OUTPUT MODE (SET BY APPLICATION SOFTWARE) User ID / Fingerprint authorized User ID unregistered/ Fingerprint error 12. APPENDIX A. Trouble Shooting ☞ Unable to enter the registration mode with master card Cause Of master card registration error or of setup error 1. Check a master card. Cause Try changing a master card and enter the registration mode with changed card. 2. Initialize the unit referring to user’s manual. (When this problem occurs before mounting the LX006 on the wall) * You can use application software for initialization if the LX006 is already mounted on the wall. 3. If the problem still remains after following the procedure above, contact the designated service center. ☞ Fingerprint isn’t registered or authenticated. Cause 1. Check the fingerprint position on the scanner. 2. Check condition of the fingerprint. 3. Check whether ADAPTIVE MODE is applied or not. If not, Set the mode as ADATIVE MODE 33 1. Check the fingerprint position on the scanner. . 위치가 지문들 Wrong잘못된 position 정상적인 지문 Correct position 2. Check condition of the fingerprint. Cause Normal Dry Wet Low pressure High pressure 3. ADAPTIVE MODE is to compensate too dry and wet fingerprint. When ADAPTIVE MODE is applied, the fingerprint capture time takes longer but the performance of fingerprint recognition will be higher. You can apply ADAPTIVE MODE using application software. ☞ The controller does not communicate with Host PC. Cause Defective cable is used, errors in wiring, an error in setting Communication ID of the controller, or damage on the communication port (either on PC side or on the controller side). 1. Please, check the settings of the application software and the controller. - Check the controller’s Communication ID is linked with application software. Solution - Set the different Communication ID when two or more controllers are installed. In case of using Serial communication. - Check the communication speed (default 57600bps) is the same as the setting on the application software. Please refer to application software manual. - Make sure that the PC’s COM port is set correctly on the application software. - The parameters at the application software should be set as follows. Parity bit : NONE Data bit : 8bit Stop bit : 1bit In case of using TCP/IP Communication - Check IP, Subnet Mask, Gateway and Port setting value. - Check more information about above setting value using the software manual. 34 2. Check the line connection for communication. In case of RS485 RS485 (mono) LX006 RS485/232 Converter RS485-A(+) RS485-A(+) RS485-B(-) RS485-B(-) PC RS232 Cable of connecter RS485(Multi Drop) LX006 LX006 RS485/232 Converter RS485-A(+) RS485-A(+) RS485-A(+) RS485-B(-) RS485-B(-) RS485-B(-) PC RS232 Cable of connecter - When a multi-drop communication doesn’t work, test one-by-one Communication from first. In case of TCP/IP Communication - Check the LED is flickering on the back of the product. - If it is flickered, check the cable connection. 3. If the trouble remains after the procedure above, contact a designated service center. 35 B. How to register fingerprint Correct Fingerprint Registration Method Correct Method Scanning Fingerprint Successful Verification / Identification Scanning Fingerprint Fail Verification / Identification Incorrect Method In case of not a fingerprint registration Wet Fingerprint Dry Fingerprint Scarred Fingerprint Injured Fingerprint Dry Wet Scarred Management Method If Fingerprint is excellently recognized... In case of dry fingerprint, please somewhat strongly press your finger (fingerprint) on fingerprint recognition scanner. In case of wet fingerprint, please lightly press your finger (fingerprint) on fingerprint recognition scanner. Please be always clean on the surface of fingerprint recognition scanner. 36 13. FCC REGISTRATION INFORMATION FCC Requirements Part 15 CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interface, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures: -. Reorient or relocate the receiving antenna. -. Increase the separation between the equipment and receiver. -. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -. Consult the dealer or an experienced radio/TV technician for help. WARNING Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. 37 14. WARRANTY POLICY AND LIMITATION OF LIABILITY IDTECK warrants this product against defects in material and workmanship for the period specified below from the date of purchase under normal customer use. This Warranty doesn’t apply: 1) to any product which has been dismantled without authorization of IDTECK or/and has a damaged or detached QC label on its back side; 2) to any losses, defects, or damages caused by improper testing, operation, installation, maintenance, modification, alteration, or adjustment; 3) to any product with a damaged or faded serial number on it; or 4) to any losses, defects, or damages caused by lightning or other electrical discharge, natural disaster, misuse, accident or neglect. This Limited Warranty is in lieu of all other warranties, obligations, or liabilities on the part of IDTECK, and IDTECK DISCLAIMS ANY AND ALL WARRANTY, WHETHER EXPRESS OR IMPLIED, OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.IDTECK does not, and cannot, know who is present, what property is located, where this product will be used; it would be extremely difficult to determine the actual damages that may result from a failure of the product to perform as anticipated; and the low price of this product is based upon the nature of the product provided and the limited liability that IDTECK assumes. IDTECK IS NOT RESPONSIBLE FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR LOSS, DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR OTHER LOSS, AND IDTECK’S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT. To obtain repair or replacement under the terms of this warranty, visit IDTECK’s Website (http://www.idteck.com) and place an online RMA request. After an RMA code is issued, return the product along with the authorization RMA code. >> Warranty Period Product Category RF CARDS (ACTIVE TYPE) FINGERPRINT MODULE / SENSOR RF READERS (WITHOUT EPOXY POTTING) STANDALONE CONTROLLERS CONTROL PANELS FINGERPRINT READERS RF READERS (WITH EPOXY POTTING) RF CARDS (PASSIVE TYPE) 38 Warranty Period 1 year 2 years Lifetime 15. HOW TO MAKE RMA REQUEST (AFTER SALES SERVICE) To make the RMA request, the product must be initially registered on IDTECK webpage. After registering the product, please send it to IDTECK RMA Center. Please follow the instructions below: 1. Please register the RMA request via IDTECK webpage. : www.idteck.com “Support & Download” “Online RMA” “RMA REQUEST” (Please refer to the IDTECK webpage for more details.) 2. RMA Code will be issued after the RMA Center reviews the RMA request form. 3. Enclose the product along with the RMA Code and send it to IDTECK RMA Center. (Product without RMA Code is not accepted.) If you have any questions or problems regarding the RMA services, please contact us using the contact information below. Friendly representatives at IDTECK are always standing by to provide the best after sales services. IDTECK Headquarter 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea Tel: +82 2 2659 0055 Fax: +82 2 2659 0086 E-mail: webmaster@idteck.com Website: www.idteck.com E-Training Center: http://www.idtecktraining.com IDTECK Production Facility and RMA Center 3F, 10/10-1/10-2, Dodang-Dong, Weonmi-Gu, Bucheon-Si, Gyeonggi-Do 420-130, Korea Tel: +82 2 2659 0055 Fax: +82 2 2659 0086 E-mail: webmaster@idteck.com Website: www.idteck.com E-Training Center: http://www.idtecktraining.com 39 The specifications contained in this manual are subject to change without notice. 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea Tel : +82-2-2659-0055 Fax : +82-2-2659-0086 E-mail : webmaster@idteck.com Copyright © IDTECK Co., Ltd.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 40 Language : ko-KR Tagged PDF : Yes Title : 각부의명칭 Author : (주)아이디-테크 연구소 연구소장 유명호 Creator : Microsoft® Office Word 2007 Create Date : 2016:05:02 18:32:46+09:00 Modify Date : 2016:05:03 11:36:37+09:00 Producer : Microsoft® Office Word 2007EXIF Metadata provided by EXIF.tools