User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 285792 |
| Application ID | QzGAWpfdT7Gv/7w6px2puQ== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Microsoft Word - pdf |
| Filesize | 94kB (1175041 bits) |
| Date Submitted | 2002-11-25 00:00:00 |
| Date Available | 2002-11-25 00:00:00 |
| Creation Date | 2002-11-25 21:39:24 |
| Producing Software | Acrobat Distiller 5.0.5 (Windows) |
| Document Lastmod | 2002-11-25 21:39:24 |
| Document Title | Microsoft Word - 285792.DOC |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | fcc |
STAR RF30+ PROXIMITY READER USER’S MANUAL Proximity Reader ID TECK Co. Ltd. RF30-20011104 STAR RF30+ PROXIMITY READER CONTENTS RF30-20011104 1. Introduction page 3 2. Identifying supplied parts page 3 3. Specification page 3 4. Installation page 4 5. Wire Color Table of the Reader page 5 6. Wire Connection to Controller page 5 7. Operation page 6 8. FCC Registration Information page 7 9. Warranty and Service page 8 STAR RF30+ PROXIMITY READER 1. Introduction The STAR RF30+ is an elegant looking and attractive 12" read range proximity reader which can be mounted on any flat wall surface. The RF30+ uses the electronics module in epoxy potting that ensures successful operations even in harsh environments. The two-color LED of green and red and the inside Piezo buzzer sound will guarantee you accurate and reliable system operations. 2. Identifying supplied parts Please unpack and check the contents of the box. Reader Module RF30+ Bezel Instruction 3. Specification Read Range Input Voltage/Current Output Format External Beeper control Input External LED control Input LED/Beeper Color Operating Environment Overall Size(WxHxD) Weight RF30-20011104 Up to 12"(30cm) DC 7V ~ 17V / Max. 170mA 26 bit Wiegand, Magstripe ABA Track II Low Active, DC 0 ~ 12V, Max. 50 mA Low Active, DC 0 ~ 12V, Max. 50 mA 2-Color LED(Red and Green) / Piezo Buzzer Dark Gray -31 ~ 149 (-35 ~ +65 ), 0~90% Humidity 5.2"x 6.2"x0.8"(130x154x20.5mm) 0.93 lbs (420g) STAR RF30+ PROXIMITY READER 4. Installation 4-1. Wall Mount Drill two 6-32 or M3 holes 3.3"(8.38cm) apart in vertical and drill one 1/2" hole for the reader cable 1.7"(4.31cm) apart from the top hole. (If you have installed an electric gang box then skip this step and go to step 4.2.) 4-2. Put reader cable into the center hole and install the reader module by using two 6-32 or M3 screws (Not included). 4-3. Put bezel on to the reader module then push bezel until you hear the locking sound. RF30-20011104 STAR RF30+ PROXIMITY READER 5. Wire Color Table of the Reader POWER Power(DC +7V~+17V) DC(+) Power(DC Ground) DC(-) (GND) INPUT Beeper control input BEEP LED control input LED OUTPUT(Wiegand Format) Wiegand Data-0 Data-0 Wiegand Data-1 Data-1 OUTPUT(RS232 Format) RS232(TX) TX OUTPUT(ABA Track II Format) ABA(Card Present) CP ABA(Clock) CLK ABA(Data) Data Note: All ABA Track II outputs are open collector output. 6. Wire Connection to Controller RF30-20011104 Red wire Black wire Blue wire Yellow wire Green wire White wire White wire Orange wire White wire Green wire STAR RF30+ PROXIMITY READER 7. Operation 7-1. Once power is applied, you should hear three beeping sounds and LED changes color to red-green-red indicating that the reader is in standby mode after a successful initialization and diagnostics. 7-2. Present proximity card to the reader until you hear the beeping sound and see the LED changes color to Green. The reader will send the RF card data to the controller then the LED will change color to Red again for the next reading. 7-3. LED Control: To change the LED colors, you may connect the LED Control Input (Yellow wire) to ground and the Green LED will turn on indicating that the reader is in standby mode. Present proximity card and the LED will change color to Red then Green again for the next reading. 7-4. Beeper Control: In normal operation, the reader generates one beep when it reads a proximity card, however additional beeps can be generated to improve indication for access status (granted or denied) by forcing the beeper control input (Blue wire) to system ground level. The beeper will remain on as long as the Blue wire is connected to system ground. RF30-20011104 STAR RF30+ PROXIMITY READER 8. FCC REGISTRATION INFORMATION FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the radio or television off and on, the user is encouraged to try to correct interference by one or more of the following measures. 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on another circuit. 4. Consult the dealer or an experienced radio/TV technician for help. RF30-20011104 STAR RF30+ PROXIMITY READER 9. Warranty and Service The following warranty and service information applies only to the United States of America and Republic of Korea. For the information in other countries, please contact your local distributor. To obtain in or out of warranty service, please prepay shipment and return the unit to the appropriate facility listed below. IN THE UNITED STATES RF LOGICS Inc. Service Center 3026 Scott Blvd., SANTA CLARA, CA95054 Tel.: (408) 980-0001 Fax.: (408) 980-8060 E-mail: rflogics@rflogics.com Web-site: www.rflogics.com OUTSIDE OF THE UNITED STATES ID TECK CO., LTD. Service Center 5F Ace Techno Tower Bldg., 684-1 Deungchon-dong, Gangseo-gu, SEOUL 157-030, KOREA Tel.: +82 (2) 659-0055 Fax.: +82 (2) 659-0086 E-mail: webmaster@idteck.com Web-site: www.idteck.com Please use the original container, or pack the unit(s) in a sturdy carton with sufficient packing to prevent damage, include the following information: 1. A proof-of-purchase indicating model number and date of purchase. 2. Bill-to address 3. Ship-to address 4. Number and description of units shipped. 5. Name and telephone number of person to contact. 6. Reason for return and description of the problem. NOTE: Damage occurring during shipment is deemed the responsibility of the carrier, and claims should be made directly to the carrier. RF30-20011104
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Create Date : 2002:11:25 21:39:24-08:00 Modify Date : 2002:11:25 21:39:24-08:00 Page Count : 8 Creation Date : 2002:11:26 05:39:24Z Mod Date : 2002:11:26 05:39:24Z Producer : Acrobat Distiller 5.0.5 (Windows) Author : fcc Metadata Date : 2002:11:26 05:39:24Z Creator : fcc Title : Microsoft Word - 285792.DOCEXIF Metadata provided by EXIF.tools