IKEA of Sweden ICTD-KL-1 Remote controller User Manual ICTD KL 1

Download:
Mirror Download [FCC.gov]
Document ID	2803215
Application ID	UktcyGV9q0RBcrzQ0iS1nQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	4.1kB (51209 bits)
Date Submitted	2015-11-05 00:00:00
Date Available	2015-11-05 00:00:00
Creation Date	2015-10-14 13:50:04
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2015-10-14 13:50:04
Document Title	Microsoft Word - ICTD-KL-1 User manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	jixia.gao

User manual of Remote Control
1、 Model No.: ICTD-KL-1
2、Technical Parameter
a) WORKING VOLTAGE: 1.8~3.6 V(Normal：2X1.5VDC);
b) Transmit speed: 250KHz;
c) Frequency band: 2436.20 +/- 0.03 MHz
3、Application
This Remote Control can match with 10W, 20W and 30W dimmable LED drivers. The match method is following:
a) Punched the code button on Receiver, the indicator lighted, you can undertake to code.
b) In the case of the receiver indicator light, extended press the button on remote control until the indicator second lighted.
Complete send code command.
c) Once receiver received the code command, the indicator flash three times showing the code is successful, after lights
out.
There are three kinds of remote control dimmer.
Press the remote control button, dimming state change by the cycle: OFF->35%->100%->35%->OFF.
4、Remote Control Block Diagram:
5、Driver Block Diagram:
Caution:
This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type
and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the equivalent
isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de
brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2015:10:14 13:50:04+08:00
Create Date                     : 2015:10:14 13:50:04+08:00
Format                          : application/pdf
Title                           : Microsoft Word - ICTD-KL-1 User manual.doc
Creator                         : jixia.gao
Document ID                     : uuid:23be8196-b865-4f57-8bb4-cb880a55d8d8
Instance ID                     : uuid:b29fdc2d-cd6b-43c5-b4e2-14f2ab4ce4d5
Page Count                      : 2
Author                          : jixia.gao

EXIF Metadata provided by EXIF.tools