INID NGRPAOLF RFID Reader User Manual mdoc091201

INID BV RFID Reader mdoc091201

Contents

system manual

INID MultiSmart readersSpecificationsTypical read rangeTechnology distanceMifare ISO card1) 60 mm 2.4 inchLF Proximity ISO card2) 30 – 60 mm 1.2 – 2.4 inch1) Depends on transponder antenna geometry.1) Depends on LF technology and card antenna geometry.Power Supply7 - 24 Volt DC (12 VDC recommended)Power consumptionmodel average peakINID MultiSmart 1300 mW 1750 mWINID MultiSmart PIN 1300 mW 2050 mWCurrent consumption @12 VDC3)model average peakINID MultiSmart 110 mA 146 mAINID MultiSmart PIN 110 mA 171 mA3) Use Ohm's law to calculate current at different voltages.InterfaceInputs type and protection specificsOutputs type and protection specificsDimensions143 x 50 x 25 mm / 5.63 x 2 x 1 inchMaterialUL94-V0 rated LEXAN® 925UOperating temperature-25° to 65° C / -15° to 150° FProtection classIP54 Complete protection against contact, protection against dust deposit. Protection from splashed water.Cable specifications (non-shielded)interfacemaximum cable lengthmin.conductor size with 12 V supply2)meters feet mm2AWGWiegand61 200 0.25 2491 300152 500 0.34 22Clock/Data 25 800.25 24TTL serial 1.5 5RS232 2.4 8RS485/RS422 (cable power)61 200152 500 0.34 22RS485/RS422 (local power) 1220 4000 0.25 24CAN bus system / speed dependent2) With a 24V supply, minimum conductor size is AWG 24 for all interfaces and lengths.FeaturesINID readers have a slim mullion mountable design and are designed for both in- and outdoor use. The INID reader can be mounted on any surface without significant performance degradation. For mounting to a metal surface however, a non-metallic spacer is advised.The switch mode power supply of the reader accepts a wide range input from 7 - 24 VDC. Higher input voltages result in lower current consumption and allow for cost effective wiring with a smaller conductor diameter.Reader output formats are determined by the personalization of the card and/or configuration of the reader.Separate models are available for card-only and card+PIN.Electrical interface options for WG/C&D/TTL serial, RS485/RS422, RS232 and CAN bus are available with separate models.PIN codeINID PIN readers provide extensive options for PIN data formats and output protocols. The card and PIN code data is sent separately and independently allowing host system determined operation for card-only, PIN-only and card and PIN usage.IndicationsUser feedback is provided by a single LED bar and a multi-tone sounder. User feedback is controllable by the host system. PIN models are equipped with back lighting of the PIN code digits for usage in dark environments.OperationWhen a proximity card is read successfully the card associated code is send to the Host system, the LED bar lights briefly and the sounder sounds a short tone.When a PIN is entered the data is transmitted; at each key press a click sound is produced and the LED bar lights briefly. The back light of the PIN code lights up after a successful card read or at the first key press.The LED bar or individual LED bar segments and the buzzer are also controllable by the Host system. INID MultiSmart readers - installation and operation manual version 1.02; March 16, 2012
Connector AssignmentsWiegand / Clock and Data / TTL serial500-5005 INID MultiSmart reader WG/C&D/TTL500-5045 INID MultiSmart PIN reader WG/C&D/TTL1 LED 1 - Green 5 BUZZER RXD2 LED 2 - Amber 6 TAMPER3 D1 DATA TXD 7 GND4 D0 CLOCK TXE 8 POWERRS485 / RS422500-5015 INID MultiSmart reader RS485/RS422500-5055 INID MultiSmart PIN reader RS485/RS4221 LED 1 - Green 5 RS485 n.c. RS422 RX-2 LED 2 - Amber 6 RS485 n.c. RS422 RX+3 RS485 TRX+ RS422 TX+ 7 GND4 RS485 TRX- RS422 TX- 8 POWERCaution: floating communication lines may cause spurious emissions. Ensure all communication lines are properly biased and terminated.RS232 500-5025 INID MultiSmart reader RS232500-5065 INID MultiSmart PIN reader RS2321 LED 1 - Green 5 RTS2 LED 2 - Amber 6 RXD3 CTS 7 GND4 TXD 8 POWERCAN bus500-5035 INID MultiSmart reader CAN bus500-5075 INID MultiSmart PIN reader CAN bus1 LED 1 - Green 5 n.c.2 LED 2 - Amber 6 n.c.3 CANL 7 GND4 CANH 8 POWERParts list1 Reader front qty: 12 Terminal connector qty: 13 Mounting backplate qty: 14 Enclosure screw qty: 15 Installation sheet qty: 1Installation instructions1 Determine an appropriate position for the reader and drill two holes for mounting the backplate and one hole for the cable, see diagram for measurements. Do not mount readers less than 20 cm (8 inches) apart.2 Pull the cable trough the hole in the backplate and mount the backplate. Protect the cable against sharp edges and any damage from chafing.3 Remove the terminal connector from the front of the reader. Prepare the end of the cable and wires, eliminate any loose or frayed strands. Keep the wire ends as short as practical.4 Connect the wires to the connector according to the reader type. Wire ends, termination resistor leads and optional permanent links shall be kept as short as possible.5 Place the connector on the reader pins.6 Place the reader front over the hinge of the backplate and close the reader (see diagram), keeping the wiring in the lower part of the reader housing. DO NOT use excessive force, retract the cable if necessary.7 Test the reader: apply power and present a valid card. The LED bar should flash and the sounder should produce a short tone indicating a successful read. If the Host system is connected to LED bar and sounder inputs these should follow the functionality of the Host system.8 The reader front should now be secured to the backplate using the supplied enclosure screw.This device contains 2 transmittersCertifications CE, FCCFCC ID: YAB-ISOACRDR (model 50XX) 13.56 MHzYAB-NGRPAOLF (model 40XX) 115 – 148 kHzCompliance statementThis device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:1) this device may not cause harmful interference, and2) this device must accept any interference received, including interference that may cause undesired operation.Warning (part 15.21)Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This in particular is applicable for the antenna which has been delivered with the reader.Consult your National Authority if any authorization is needed for this product.INID MultiSmart readers - installation and operation manual version 1.02; March 16, 2012INID BVMariëttahof 272033 WS HaarlemThe NetherlandsPhone: +31 (0)23 5335 420Web: www.inid-readers.comFor mounting, use only flat head screws with a maximum shank size of 4 mm (5/32”, #7)

Navigation menu