IP COM NETWORKS AP345V2 11AC Dual Band Ceiling Access Point User Manual 1

SHENZHEN IP-COM NETWORKS CO.,LTD. 11AC Dual Band Ceiling Access Point 1

15_AP345 UserMan

Know Your AP Install the APSet Up Your WiFi Network3. 2. 2 3Position the bracket onto the celling andmark screw holes on the celling with the marker.Drill holes in the marked positions using hammer drill.Knock the expansion bolts into the holes using the rubber hammer.3Use the screwdriver to drive screws into the expansion bolts so as to fasten the bracket.Port / ButtonDescriptionLANIt is a 10/100 Mbps auto-negotiation port used to transmit data or supply PoE power for the AP using an Ethernet cable. PoE devices compliant with IEEE802.3aforIEEE802.3atstandardcansupplypowertotheAP.PWRIt is a DC power jack used to connect to the included power adapter.RESETIt is used to reset the AP. Method to reset: When the SYS indicator blinks, hold the RESET button down for about 8 seconds. The AP is reset successfully when the SYS indicator gets solid on.Insert the hooks of the AP into the slots of the bracket, and slide the AP to one side to make sure that the AP is fixed well in the bracket. LED indicatorStatus DescriptionSYSSolid on The system is starting. If the indicator is still solid on after the AP finishes startup, it indicates that the system is faulty.Blinking The AP is working properly.OffThe AP is powered off or the LED indicator is disabled.Scenario 1: Set up WiFi network without a management device for IP-COM APScenario 3: Set up WiFi network with an IP-COM router that can manage APsTip:If you have more than one AP, connect one AP to your PoE switch and perform steps ❶ to ❹ for it first. Then connect and configure other APs one by one.1Connect devicesConnect your AP to a PoE port of the PoE switch using an Ethernet cable.Refer to the following figure for detailed connection.After finishing connection, ensure that the AP's LED indicator blinks and the lower-right network icon on your computer is not displayed . Configure the IP address of your computer（Example: Win7)Right-click the network icon on the lower-right corner of your computer. Click Open Network and Sharing Center, Local Area Connection, and then Properties. Double-click Internet Protocol Version 4 (TCP/IPv4), select Use the following IP address, set IP address to 192.168.0.x (x: 2 to 253. The IP address in this example is 192.168.0.10) and Subnet mask to 255.255.255.0, and click OK.Set WiFi name and WiFi password for the APStart a web browser on your computer, enter 192.168.0.254 in the address bar, and press Enter to log in the web UI of your AP. Click Quick Setup on the web UI, configure SSID (WiFi name), Security Mode (WPA2-PSK is recommended), Key for the 2.4 GHz WiFi network, and click Save. Then set Radio Band to 5 GHz, configure SSID, Security Mode and Key for it as well, and click Save.4Change the IP address of the AP Click Network>LAN Setup. Change the IP address of the AP to 192.168.0.x (x: 2 to 253), and ensure that the new IP address has not been used in this network, then click Save. For example, you can set the new IP address of the first AP to 192.168.0.201, and the new IP address of the second AP to 192.168.0.202. Wait a moment for the settings to take effect. Now you can access the internet by connecting your wireless devices to the AP's WiFi network.WiFi name: The SSID you set in step .WiFi password: The key you set in step . Scenario 2: Set up WiFi network with an IP-COM AP Controller1Connect devicesUse Ethernet cables to connect APs to the PoE ports of the switch, and your computer to the IP-COM AP Controller (AC). Refer to the following figure for detailed connection.2ConfigureAPsIn order to configure your APs, start a web browser on your computer and log in to the web UI of the AC. Refer to your AC's user guide for detailed configuration instructions. FAQTip:You may need a rubber hammer, a marker, a hammer drill, a drill bit, a screwdriver, and a ladder for the installation. Please prepare them yourself.Configure APsIn order to configure your APs, start a web browser on your computer and log in to the web UI of your router. Refer to the router's user guide for detailed configuration instructions. Note:PoE supply is used as an example in all the setup instructions below. 332* Tip: If you cannot log in to the web UI of the AP, refer to Q1 in FAQ.Q1: I cannot access the web UI of the AP after entering 192.168.0.254. What should I do?A1: Try the following solutions and log in again: Ensure that all your Ethernet cables are properly connected. If there is no AC or IP-COM router in the network, ensure that the IP address of your computer has been set to 192.168.0.x (x: 2 to 253), and the IP address is not used by any other devices in the same network. Clear the cache of your web browser or replace the web browser. Disable the firewall of your computer or replace your computer. If two or more APs are connected in the network without an AC / IP-COM management router, an IP address conflict may happen. You should leave only one AP in the network first and set a new IP address 192.168.0.x (x: 2 to 253) for the AP. Then repeat this procedure to change the IP addresses of the other APs. Meanwhile, make sure that the IP address of your computer is in the same network segment with your APs' new IP addresses. Then try logging in to the web UI of your APs using their new IP addresses.If the AP has been managed by the AC or IP-COM router in the network, the AP's IP address may be no longer 192.168.0.254. In that case, go to the web UI of the AC / router to view the new IP address of the AP, and then log in to the AP's web UI using the new IP address.If the problem still persists, hold the RESET button down for 8 seconds to restore the AP to factory settings, and then try logging in again.Q2: My AP controller (AC) cannot find my AP. What should I do?A2: Check the following items: Ensure that all the devices in the network are connected well and the LED of the AP blinks. If VLANs have been set in your network, ensure that the AP belongs to the same VLAN as that of your AC. Reboot your AP. Ensure that the firmware versions of your AP and AC are the latest firmware versions available on www.ip-com.com.cnReset your AP. Method to reset: When the SYS indicator blinks, hold down the RESET button for about 8 seconds. The AP is reset successfully when the SYS indicator gets solid on.1Connect devicesUse Ethernet cables to connect APs to the PoE ports of the switch, and your computer to the IP-COM router. Refer to the following figure for detailed connection.Connect an Ethernet cable (CAT5 or better) to the LAN port of the AP. If you choose to power on the AP by DC supply, connect the PWR port of the AP using the power adapter included in the package.IP-COM AP Controller PoE switch InternetComputer RouterLaptop Smart phone Tablet PCAP AP APIP-COM Router (Supporting AP management)Laptop Smart phone Tablet PCPoE switch APInternetComputerRouterUplink port LAN port WAN portUplink port LAN port WAN portAP AP APInternetLAN port WAN portUplink portLaptop Smart phone Tablet PCComputerPoE switch LAN port6124RESET5RESETSystem LED indicator1. LANPWRRESETRESET11AC Dual Band Ceiling Access PointQuick Installation GuideIf any item is incorrect, missing, or damaged, please keep the original package and contact the local reseller or distributor immediately.*For more product or function details, please go to www.ip-com.com.cn to download the user guide.Package Contents Access point * 1 Bracket * 1Power adapter * 1Quick installation guide * 1 Mounting accessory (including sleeve anchors and screws) * 1 SlotHookGeneralYou can get IP settings assigned automatically if your network supports this capability. Otherwise,you need to ask your network administrator forthe appropriate IP settings.Obtain an IP address automaticallyUse the following IP address:Obtain DNS server address automaticallyUse the following DNS server addresses:AdvancedOK CancelDefault gateway:Subnet mask:IP address:Preferred DNS server:Alternate DNS server:Validate settings upon exitInternet Protocol Version 4 (TCP/IPv4)Properties255 255 255 0192 010168CE Mark WarningThis is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.Operations in the 5.15-5.25GHz band are restricted to indoor use only.The mains plug is used as disconnect device; the disconnect device shall remain readily operable.This equipment should be installed and operated with minimum distance 20cm between the device and your body.NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.Declaration of ConformityHereby, IP-COM Networks Co., LTD. declares that the radio equipment type AP345 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: http://www.ip-com.com.cn/en/ce.html Operate Frequency: 2.4 GHz: 2.412 GHz – 2.472 GHz 5 GHz: 5.15 GHz – 5.25 GHzEIRP Power (Max.): 2.4 GHz: 19.95 dBm 5 GHz: 22.9 dBmSoftware Version: V1.0.0.4FCC StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:— Reorient or relocate the receiving antenna.— Increase the separation between the equipment and receiver.— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.— Consult the dealer or an experienced radio/TV technician for help.The device is for indoor usage only. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Radiation Exposure StatementThis device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Operating frequency: 2412 – 2462 MHz, 5150 – 5250 MHz, 5725 – 5850 MHzNOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.Operating temperature: (-10 – 40) °COperating humidity: (10 – 90) % RH, (non-condensing)Copyright© 2018 IP-COM Networks Co., Ltd. All rights reserved.This documentation (including pictures, images, and product specifications, etc.) is for reference only. To improve internal design, operational function, and/or reliability, IP-COM reserves the right to make changes to the products described in this document without obligation to notify any person or organization of such revisions or changes.Technical Support MAC AddressC8:3A:35:83:F1:B0IP Address Type  Static IP Address IPAddress Subnet Mask255.255.255.0Gateway192.168.0.1PrimaryDNSServer8.8.8.8SecondaryDNSServer 8.8.4.4 Device Name Access Point Ethernet Mode Auto-negotiation 10 Mbps Half DuplexLANSetupStatusQuick SetupNetwork SettingsLAN SetupDHCP ServerWireless SettingsSNMPDeploymentToolsAdministrator admin：SaveRestoreHelpStatusQuick SetupNetworkWirelessSNMPDeploymentTools Radio Band 2.4 GHzWorking ModeAP Client + AP SSID Security ModeWPA2-PSKEncryption AlgorithmAESTKIPTKIP&AES KeyAdministrator admin：Quick SetupSaveRestoreHelpTelephone: (86 755) 2765 3089 Website: http://www.ip-com.com.cn E-mail: info@ip-com.com.cnAddress Info: Room 101, Unit A, First Floor, Tower E3, No. 1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052 Caution:Adapter Model: BN036-A12012E/BN036-A12012BManufacture: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY Co., LTD.Input: 100-240 V AC, 50/60 Hz, 0.4 AOutput: 12 V 1.0 A : DC Voltage RECYCLINGThis product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment.IP-COM router (Supporting AP management)For EU/EFTA, this product can be used in the following countries:

Navigation menu