Icom Ifr5100 Users Manual IC FR5100/FR6100 Instruction

2015-02-05

: Icom Icom-Ifr5100-Users-Manual-357598 icom-ifr5100-users-manual-357598 icom pdf

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

INSTRUCTION MANUAL

VHF FM REPEATER

iFR5100
UHF FM REPEATER

iFR6100

IMPORTANT
R E A D T H I S I N S T RU C T I O N M A N UA L
CAREFULLY before attempting to operate the repeater.

SAVE THIS INSTRUCTION MANUAL– This
manual contains important safety and operating instructions for the IC-FR5100/IC-FR6100 vhf/uhf fm
repeaters.

EXPLICIT DEFINITIONS
WORD
RWARNING
CAUTION
NOTE

DEFINITION
Personal injury, fire hazard or electric
shock may occur.
Equipment damage may occur.
If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.

PRECAUTIONS
R WARNING HIGH VOLTAGE! NEVER at-

tach an antenna or internal antenna connector during
transmission. This may result in an electrical shock or
burn.

R WARNING HIGH VOLTAGE! NEVER in-

stall the antenna at any place that person touch the
antenna easily during transmission. This may result in
an electrical shock or burn.

R WARNING! NEVER apply AC to the DC

power receptacle on the repeater rear panel. This
could cause a fire or damage the repeater.

R WARNING! NEVER apply more than 16 V DC,

such as a 24 V battery, to the DC power receptacle
on the repeater rear panel. This could cause a fire or
damage the repeater.

R CAUTION! NEVER let metal, wire or other objects touch any internal part or connectors on the rear
panel of the repeater. This may result in an electric
shock.

Place the repeater in a secure place to avoid inadvertent use by children.
BE CAREFUL! The heatsink will become hot when
operating the repeater continuously for long periods.
BE CAREFUL! If a linear amplifier is connected, set
the repeater’s RF output power to less than the linear
amplifier’s maximum input level, otherwise, the linear
amplifier will be damaged.
Use Icom microphones only (optional). Other manufacturer’s microphones have different pin assignments, and connection to the repeater may damage
the repeater.
Icom optional equipment is designed for optimal performance when used with this repeater. We are not
responsible for the repeater being damaged or any
accident caused when using non-Icom optional equipment.

R CAUTION! NEVER expose the repeater to
rain, snow or any liquids.

DO NOT use or place the repeater in areas with temperatures below –25°C or above +55°C. Be aware
that temperatures can exceed +80°C, resulting in
permanent damage to the repeater if left there for extended periods.
DO NOT place the repeater in excessively dusty environments or in direct sunlight.
DO NOT put anything on top of the repeater. This will
obstruct heat dissipation.
Icom, Icom Inc. and the
logo are registered trademarks
of Icom Incorporated (Japan) in the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other
countries.

FORWARD

SUPPLIED ACCESSORIES

Thank you for purchasing this Icom repeater. The
IC-FR5100/IC-FR6100 vhf/uhf fm repeaters is designed and built with Icom’s state of the art technology and craftsmanship. With proper care, this product
should provide you with years of trouble-free operation.

The following accessories are supplied.

We want to take a couple of moments of your time to
thank you for making the IC-FR5100/IC-FR6100 your repeater of choice, and hope you agree with Icom’s philosophy of “technology first.” Many hours of research and
development went into the design of your IC-FR5100/
IC-FR6100.

Handles

For handles attachment
Spacers

Screws

Function name stickers*

DC power cable

KEY SEAL

D FEATURES
m Up to 2 channels operation

You can install a channel extension module (optional UR-FR5100/UR-FR6100) into a repeater. 2
channels can be operated as the repeater when a
channel extension module is installed.

m Built-in 5-Tone, DTMF encoder & decoder

Multiple signaling systems are equipped as standard. These systems are fully compatible with
Icom F-series radios.

m DTMF remote control capability
You can control the repeater from a remote location over the air or over a phone line with DTMF.

m D-Sub 25 pin ACC port equipped
You can use the optional equipment via the D-sub
25 pin ACC port equipped on the repeater’s rear
panel.

m Other features

- Wide frequency coverage
(136 to 174 MHz, 400 to 470 MHz)
- PC programmable
- 19 inch rack mount
- O ptional Voice Scrambler Unit (UT-109R/
UT-110R) for base operating mode

VOICE CODING TECHNOLOGY
The AMBE+2™ voice coding Technology embodied in this
product is protected by intellectual property rights including
patent rights, copyrights and trade secrets of Digital Voice
Systems, Inc. This voice coding Technology is licensed
solely for use within this Communications Equipment. The
user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or
disassemble the Object Code, or in any other way convert
the Object Code into a human-readable form. U.S. Patent
Nos. #5,870,405, #5,826,222, #5,754,974, #5,701,390,
#5,715,365, #5,649,050, #5,630,011, #5,581,656,
#5,517,511, #5,491,772, #5,247,579, #5,226,084 and
#5,195,166.

* Used for labelling the programmable function
keys according to their assinged functions.

TABLE OF CONTENTS
IMPORTANT................................................................ i
EXPLICIT DEFINITIONS............................................. i
PRECAUTIONS........................................................... i
FORWARD................................................................. ii
VOICE CODING TECHNOLOGY............................... ii
SUPPLIED ACCESSORIES...................................... ii
TABLE OF CONTENTS............................................. ii
1 PANEL DESCRIPTION..................................... 1–3
n Front panel......................................................... 1
D Function display............................................. 2
n Rear panel.......................................................... 2
D Accessory connector..................................... 3
2 INSTALLATION AND CONNECTIONS............. 4–6
n Unpacking.......................................................... 4
n Selecting a location............................................ 4
n Antenna connection........................................... 4
n Front panel connection....................................... 5
n Rear panel connection....................................... 5
n Power supply connection................................... 6
n Mounting the repeater........................................ 6
D Using the supplied handle.............................. 6
3 OPERATION.......................................................... 7
n Receiving and transmitting................................. 7
D Repeater operation........................................ 7
D Base station operation................................... 7
4 MAINTENANCE.................................................... 8
n Troubleshooting.................................................. 8
n Fuse replacement.............................................. 8
D Line fuse replacement.................................... 8
5 OPTIONS............................................................... 9
6 ABOUT CE.................................................... 10–12
ii

PANEL DESCRIPTION

■ Front panel

Function
display

o
q INTERNAL SPEAKER
Monitors received signals.
w VOLUME CONTROL [VOLUME] (p. 7)
Adjusts the audio output level.
e SELECTOR DIAL [SELECT]
Rotate to adjust the squelch threshold level, select
the operating channel. (Depending on the preprogrammed condition.)

t TRANSMIT INDICATOR [TX]
Lights red while transmitting.
y BUSY INDICATOR [BUSY]
Lights green while receiving a signal or when the
noise squelch is open.
About [PWR], [TX] and [BUSY] indicators:
‘A’ and ‘B’ modules indicators are available for
these indications. ‘A’ module's indicator correspond
to the original module, and ‘B’ module's indicator
correspond to an extended module.

u MICROPHONE CONNECTOR [MIC]
This 8-pin modular jack accepts the optional microphone.
K
EEP the [MIC] connector cover attached to the
repeater when the optional microphone is not
used.

r POWER INDICATOR [POWER]
➥ Lights green at ‘A’ module's indicator while the
repeater power is turned ON.
When a channel extension module is installed:
➥ Lights green at the selected module indicator
(‘A’ or ‘B’) while the repeater power is turned
ON.
➥ Lights orange at the un-selected module indicator (‘A’ or ‘B’) while the repeater power is turned
ON.

r
t
y

q +8 V DC output (Max. 15 mA)
w Output port for PC programming
e NC
r M PTT (Input port for TX control)
t Microphone ground
y Microphone input
u Ground
i Input port for PC programming

i POWER SWITCH [POWER]
➥ Push to turn the repeater power ON.
➥ P ush and hold for 3 sec. to turn the repeater
power OFF.
When a channel extension module is installed:
➥ While the repeater power is turned ON, push
to select the desired module to operate the repeater as the base station.
• The power indicator of the selected module unit
lights green.

o DEALER-PROGRAMMABLE KEYS
D
esired functions can be programmed independently by your dealer.
Ask your dealer for details.

• Because these keys are programmable, the functions
of these keys are unique to each unit.

PANEL DESCRIPTION

D Function display
q

ICOM

Inc.

q SIGNAL STRENGTH INDICATOR
Indicates relative signal strength level.

r COMPANDER INDICATOR
Appears when the compander function is activated.

w LOW POWER INDICATOR
Appears when low output power is selected.

t SCRAMBLER/ENCRYPTION INDICATOR
Appears when the voice scrambler/encryption
function is activated.

e AUDIBLE INDICATOR
Appears when the channel is in the ‘audible’ (unmute) condition.

1
2
3

y ALPHANUMERIC DISPLAY
Shows a variety of text or code information.

4
5

■ Rear panel
q w

7
8
9
10
11

The optional channel extention module can be installed.
Ask your dealer for details.

q EXTERNAL SPEAKER CONNECTOR [SP]
Connect the optional SP-22.
w RECEIVE ANTENNA CONNECTOR [RX]
Connects a receive antenna (impedance: 50 ˘)
and inputs receiving signals.

r DC POWER RECEPTACLE
Connects the supplied DC power cable from this
connector to an external 13.2 V DC power supply.

13
14

t TRANSMIT ANTENNA CONNECTOR [TX]
Connects a transmit antenna (impedance: 50 ˘)
and outputs transmit signals.

e ACCESSORY CONNECTOR [ACC]
Connects to the accessory connector.

• See pgs. 3 for accessory connector information.

18
19
20
21

PANEL DESCRIPTION

D Accessory connector

Pin No.

Description

Pin Name

Specification

No connection

—

TXD

Output terminal for serial communication data.

—

RXD

Input terminal for serial communication data.

—

RTS

Output terminal for request-to-send data.

—

CTS

Input terminal for clear-to-send data.

—

No connection

—

GND

Serial/digital signal ground

—

MOD IN

DISC OUT

EXT. D/A

VCC

EXT. A/D

GND

EXT.I/O 15

EXT.I/O 16

EXT.I/O 17

EXT.I/O 18

EXT.I/O 19

DATA IN

EXT.I/O 21

AF OUT

EXT.I/O 23

EXT.I/O 24

EXT.I/O 25

Modulator input from an external terminal unit.
Output terminal for AF signals from the AF detector circuit.
Output level is fixed, regardless of [AF] control.
The desired function can be assigned.*

Input level: 300 mV rms
Output level: 300 mV rms
—

(Default: Null)
13.2 V DC output

Output current: Less than 1 A

Customize A/D input (Not used)

—

No connection

—

Ground

—

The desired function can be assigned.*
(Default: Null)
The desired function can be assigned.*
(Default: P0 Monitor Output)
The desired function can be assigned.*
(Default: Busy Output)
The desired function can be assigned.*
(Default: Null)
The desired function can be assigned.*
(Default: EPTT Input)
Input terminal for data.
The desired function can be assigned.*
(Default: Analog Audible Output)
The AF detector Output.
The desired function can be assigned.*
(Default: Mic Mute Output)
The desired function can be assigned.*
(Default: Null)
The desired function can be assigned.*
(Default: Mic Hanger Output)

+5 V pull up, Active=L
+5 V pull up, Active=L
+5 V pull up, Active=L
+5 V pull up, Active=L
+5 V pull up, Active=L
—
+5 V pull up, Active=L
—
+5 V pull up, Active=L
+5 V pull up, Active=L
+5 V pull up, Active=L

* The desired function can be assigned using the optional CS-FR5000 cloning software. Ask your dealer for details.
3

INSTALLATION AND CONNECTIONS

■ Unpacking

■ Antenna connection

After unpacking, immediately report any damage to
the delivering carrier or dealer. Keep the shipping cartons.

For radio communications, the antenna is a critical
component, along with output power and sensitivity.
Select antenna(s), such as a well-matched 50 ˘ antenna, and feedline. 1.5:1 or better of Voltage Standing Wave Ratio (VSWR) is recommended for desired
band. Of course, the transmission line should be a
coaxial cable.

For a description and a diagram of accessory equipment included with the repeater, see ‘SUPPLIED ACCESSORIES’ on p. ii of this manual.

■ Selecting a location
Select a location for the repeater that allows adequate
air circulation, free from extreme heat, cold, or vibrations, and away from TV sets, TV antenna elements,
radios and other electromagnetic sources.

AUTION: Protect repeater from lightning by using
C
a lightning arrestor.
NOTE: There are many publications that describe
proper antennas and their installation. Check with
your local dealer for more information and recommendations.

1
2
3

TYPE-N CONNECTOR INSTALLATION EXAMPLE

Nut Rubber gasket

15 mm

4
5

Slide the nut, flat washer, rubber gasket and clamp over the coaxial
cable, then cut the end of the cable evenly.

Washer

Clamp

3 mm

Center
conductor

Strip the cable and fold the braid back over the clamp.

6 mm
Solder hole

Soft solder the center conductor. Install the center conductor pin and
solder it.

No space

Carefully slide the plug body into place aligning the center conductor
pin on the cable. Tighten the nut onto the plug body.

Be sure the center conductor is
the same height as the plug body.

15 mm (19⁄32 in) 6 mm (1⁄4 in) 3 mm (1⁄8 in)

14
15
16
17
18
19
20
21

INSTALLATION AND CONNECTIONS

■ Front panel connection

HM-152 HAND
MICROPHONE
(optional)

MICROPHONE CONNECTOR (Front panel view)

SM-25 DESKTOP
MICROPHONE
(optional)

q +8 V DC output (Max. 10 mA)
w Output port for PC programming
e NC
r M PTT (Input port for TX control)
t Microphone ground
y Microphone input
u Ground
i Input port for PC programming

CAUTION: DO NOT short pin 1 to ground as this can
damage the internal 8 V regulator. DC voltage is applied
to pin 1 for microphone operation. Only Icom microphones are recommended.

■ Rear panel connection
SP-22 EXTERNAL SPEAKER
ACC CONNECTOR (p. 3)
Used for external equipment control.
Connect a 4 ˘ external speaker.

[TX ANT] (p. 4)

[RX ANT] (p. 4)
20 A
fuses
R CAUTION! NEVER remove
the fuse-holder from the DC
power receptacle.

AC outlet

DC power supply
13.2 V; at least 20 A
Red Black
+
_

R When you disconnect the
DC power cable, take care
no crack of your fingernail.

AC cable

w
q Push

Supplied
DC power cable

Red

Black

INSTALLATION AND CONNECTIONS

■ Power supply connection

■ Mounting the repeater

Make sure the repeater’s power is turned OFF when
connecting a DC power cable.

D Using the supplied handle

AUTION: Voltages greater than 16 V DC will damC
age the repeater. Check the source voltage before
connecting the power cable.

The supplied handles are available for mounting the
repeater into a 19 inch rack. The handles can be installed to the repeater’s front panel.
q Attach the supplied handles to both sides of the repeater’s front panel with the spacers, then tighten
the screws as below.

1
P0

Screw

Handle
Spacer

w T he completed installation should look like as
below.

5
6

8
9
10
11
12
13
14
15
16
17
18
19
20
21
6

OPERATION

■ Receiving and transmitting
D Repeater operation
Ask your dealer for details of the repeater’s programming.
➥ When the power is turned ON, the [PWR] indicator
lights green. (p. 1)
➥ The [TX] and [BUSY] indicators light simultaneously while transmitting/receiving a signal.

• The [TX] indicator lights red.
• The [BUSY] indicator lights green.

NOTE: A power amplifier protector is built-in to the
repeater. The protector is activated when the repeater temperature becomes extremely high due
to the frequently access to the repeater to reduce
the transmit output power level. The output power
will return to the normal level when the repeater
has cooled down.

D Base station operation
Receiving

q Push [POWER] to turn the power ON.
w Set the audio and squelch levels.
➥ Rotate [SELECT]*1 fully counterclockwise in advance.
➥ R otate [VOLUME] to adjust the audio output
level.
➥ R otate [SELECT]* 1 clockwise until the noise
disappears.
e Push [CH Up]*2 or [CH Down]*2 to select the desired channel.

• When receiving a signal, the [BUSY] indicator lights
green and audio is emitted from the speaker.
• Further adjustment of [VOLUME] to a comfortable listening level may be necessary at this point.

*1 When the [SQL Level Up/Down] key function is assigned
to [SELECT].

*2 W hen the [CH Up]/[CH Down] key functions are assigned.

Transmitting

q Take the microphone off hook.
w Wait for the channel to become clear.
e Push and hold [PTT] to transmit, then speak into
the microphone at your normal voice level.
r Release [PTT] to receive.
IMPORTANT:
To maximize the audio quality of the transmitted signal:
(1) Pause briefly after pushing [PTT].
(2) Hold the microphone 1 to 2 inch (2.5 to 5 cm) from
your mouth, then speak into the microphone at a
normal voice level.

MAINTENANCE

■ Troubleshooting
The following chart is designed to help correct problems which are not equipment malfunctions.
PROBLEM

If you are unable to locate the cause of a problem or
solve it through the use of this chart, contact the nearest Icom Dealer or Service Center.

POSSIBLE CAUSE

SOLUTION

Power does not come • DC power cable is improperly connected.
on when [POWER] is
pushed.
• Fuse is blown.

REF.

• Re-connect the DC power cable correctly.

pgs.
5, 6
• Check the cause, then replace the fuse with p. 8
a spare one.

• R otate [VOLUME] clockwise to obtain a p. 7
suitable listening level.
• While in base operating mode, rotate [SE- p. 7
LECT] to counterclockwise to open the
squelch. (When the [SQL Level Up/Down]
key function is assigned to [SELECT].)
•P
ush [MONI] (if assigned) to the audio
• The audio mute function is activated.
–
mute function OFF.
•A
selective call or squelch function is acti- • Turn the appropriate function OFF.
–
vated such as 5 tone call or tone squelch.

N o s o u n d s f r o m t h e • Volume level is too low.
speaker.
• The squelch is closed.

• The front speaker is set to OFF.

• Turn the front speaker ON using the optional CS-FR5000 cloning software. Ask
your dealer for details.

1
2
3
4
5

–

6
7

Sensitivity is low and • Antenna feedline or the antenna connector • Check and re-connect (or replace if neces- p. 5
only strong signals are has a poor contact or is short-circuited.
sary), the antenna feedline or antenna conaudible.
nector.
Received signal cannot • Optional voice scrambler is turned OFF.
be understood.
• Scrambler code is not set correctly.

• Turn the optional voice scrambler ON.
• Reset the scrambler code.

–
–

• Push [HIGH/LOW] (if assigned) to select
the High power.
•P
ower amplifier protection circuit is acti- • Cool down the repeater or stop accessing
vated.
to the repeater until it has cooled down.

–

• Turn the tone squelch function ON.
No contact possible with • The other station is using tone squelch.
et the repeater to simplex, when other
• W hile in base operating mode, the re- • S
another station.
peater is set to duplex.
transceiver is set to simplex.

–
–

Output power is too low. • Output power is set to Low.

12
13
14

■ Fuse replacement
If a fuse blows or the repeater stops functioning, try to
find the source of the problem, and then replace the
damaged fuse with a new, rated fuse.

CAUTION: DISCONNECT the DC power cable

from the repeater. Otherwise, there is danger of
electric shock and/or equipment damage.

D Line fuse replacement

18
19
20
21

Fuse rating: 20 A
USE the 20 A fuse only.

OPTIONS

• SP-22 external speaker
Compact and easy-to-install.
Input impedance : 4 ˘
Max. input power : 5 W
• HM-152 hand microphone
• SM-25 desktop microphone
• UR-FR5100/UR-FR6100 channel extension modules
• UT-109R voice scrambler unit
Non-rolling type (max. 32 codes).
• UT-110R voice scrambler unit
Rolling type (max. 1020 codes).
* T he scrambler systems of the UT-109R and UT110R are not compatible with each other.
Some options may not available in some countries.
Please ask your dealer for details.

ABOUT CE

INSTALLATION NOTES
• Compliance of base station transmitter installations with EN50385
The installation of this equipment and it’s associated
antenna should be made in such a manner as to respect the EC recommended electromagnetic (EM)
field exposure limits. (1999/519/EC)
In order not to exceed these exposure limits it is necessary to determine the ‘Compliance Boundary,’ that
means the volume within which the EM field radiated
by the transmitter/antenna installation may exceed the
1999/519/EC limits. You will then need to ensure that
members of the general public do not have access
within this area. The actual Compliance Boundary for
this repeater will be totally dependant on the antenna,
feeder, RF amplifier and other passive or active devices used in the installation.
The RF output power of this repeater is 25 watts.
The figures contained in this guide are based on the
recommended limits for the general public and are
obtained by ‘worst case’ numerical analysis. For a definitive evaluation of any given installation, measurements should be made with an EM field meter and a
broadband calibrated probe.
• Installation
The antenna should be installed as high as possible
for maximum efficiency and minimum EM field at
ground-level. The evaluation of radiated field should
take into account any additional RF amplifiers used,
any loss in the antenna feeder cable and the gain of
the antenna used as well as its polar radiation pattern.
If there are any objects or structures larger than
half a wavelength close to the antenna, or within the
clearance distances specified, then these can cause
reflections which will have an effect on the overall radiation pattern.
For any installation you need to consider ‘height clearance’ (i.e. the height above any place where persons
may have access) and ‘front clearance’ (i.e. the distance in front of the antenna where the radiated field
may exceed the recommended limits). Normally with
an antenna installed on a reasonably high mast or
tower, there will not be any access point directly in
front but care should be exercised when there are
other buildings higher than the antenna within the vicinity.

• Installation with a vertical type antenna at VHFUHF
You need to consider the distances between the antenna and any point where persons may have access.
Allowing an average height of 1.8 m for a person in
the vicinity of the antenna the clearance distances
can be evaluated as follows. For the antenna a forward gain of 1.6 and downward gain of unity has been
assumed.

Height
Front
Power
EIRP Distance clearance clearance

1 watt 1.6 watts 0.32 m
2.1 m
0.4 m
10 watts 16 watts
1 m
2.8 m
1.3 m
25 watts 40 watts 1.6 m
3.4 m
2m
100 watts 160 watts 3.2 m
5 m
4m
1 kW 1600 watts
10 m
12 m
13 m
• Installation with a yagi or directive type antenna
Exposure distance assumes that the predominant radiation pattern is forwards and that radiation vertically
downwards is at unity gain (sidelobe suppression is
equal to main lobe gain). This is true of almost every
gain antenna today. Exposed persons are assumed
to be beneath the antenna array and have a typical
height of 1.8 m.
The figures assume the worst case emission of constant carrier.
RF power Clearance heights by frequency band
13 cm
Watts
10–2 m 70 cm 23 cm

and above
1
2.1 m
2 m
2 m
2m
10
2.8 m
2.7 m
2.5 m
2.3 m
25
3.4 m
3.3 m
2.7 m
2.5 m
100
5 m
4.7 m
3.6 m
3.2 m
1000
12 m 11.5 m
7.3 m
6.3 m
Forward clearance, EIRP by frequency band
13 cm

Watts
10–2 m 70 cm 23 cm and above

100
2 m
2 m
1.1 m
0.7 m
1000
6.5 m
6 m
3.5 m
3m
10,000
20 m
18 m
11 m
7m
100,000
65 m
60 m
35 m
29 m
EIRP

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
10

ABOUT CE

• Typical installation example
A UHF base station transmitter is to be installed on
the roof of an office.
The transmit power is 25 watts, there is 20 m of
RG-213 coaxial cable and the antenna is vertically
polarised dipole.
The specification of the RG-213 cable gives a loss
of 1.5 dB/10 m. There will be 3 dB loss for the 20 m
length used.

• Operating Notes
All of the above comments on RF safety assume that
the radio is transmitting continuously in a constant
carrier mode such as FM or RTTY etc.
The RF exposure limits recommended by the EC are
based on the mean power averaged over a 6 minute
period.
Therefore if the total transmit time during any 6
minute period is reduced, then the installation will be
even further within the recommended limits.

The RF power at the antenna input will be 12.5 watts.
The dipole antenna has a forward gain of 0 dBd or
1.6, giving an EIRP of 20 watts.

CE Versions of the IC-FR5100/IC-FR6100
which display the “CE” symbol on the serial
number seal, comply with the essential requirements of the European Radio and
Telecommunication Terminal Directive
1999/5/EC.

Referring to the table above for VHF/UHF vertical
antennas, this gives a front clearance distance of approx. 1.5 m and a height clearance of 3 m.
The antenna installation needs to ensure that the lowest part of the antenna is at least 3 m above any point
where the general public may gain access and that
they cannot pass within 1.5 m in front of the antenna.
If there is no general public access to the roof in
question then the antenna could be mounted on a
short stub mast. If there is such access to the roof
then the antenna could be mounted on top of a short
mast of 3.2 m high. The mast position should be such
that the antenna can radiate clearly i.e. no other object or structure is within 1.5 m (preferably more).
It should be relatively easy to fulfil all these recommendations.
If for any reason such minimum distances are impossible to guarantee then some type of access control fence or barrier around the antenna installation
should be provided.
Should a Yagi type antenna be used then you will
have to obtain a 3 dimensional polar plot of the radiation characteristic from the manufacturer and evaluate
the clearance distances in both vertical and horizontal
planes.

This warning symbol indicates that this
equipment operates in non-harmonised
frequency bands and/or may be subject to
licensing conditions in the country of use.
Be sure to check that you have the correct
version of this radio or the correct programming of this radio, to comply with national licensing requirement.
• List of Country codes (ISO 3166-1)

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

Country
Austria
Belgium
Bulgaria
Croatia
Czech Republic
Cyprus
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Iceland
Ireland
Italy
Latvia

Codes
AT
BE
BG
HR
CZ
CY
DK
EE
FI
FR
DE
GR
HU
IS
IE
IT
LV

18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33

Country
Liechtenstein
Lithuania
Luxembourg
Malta
Netherlands
Norway
Poland
Portugal
Romania
Slovakia
Slovenia
Spain
Sweden
Switzerland
Turkey
United Kingdom

Codes
LI
LT
LU
MT
NL
NO
PL
PT
RO
SK
SI
ES
SE
CH
TR
GB

ABOUT CE

DECLARATION
OF CONFORMITY
We Icom Inc. Japan

0168

1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan

Declare on our sole responsibility that this equipment complies with the
essential requirements of the Radio and Telecommunications Terminal
Equipment Directive, 1999/5/EC, and that any applicable Essential Test
Suite measurements have been performed.

Düsseldorf 16th Apr. 2008
Place and date of issue

Kind of equipment:

VHF REPEATER

Type-designation:

iC-fr5100/ur-fr5100

Version (where applicable):

136–174 MHz 6.25 kHz/12.5 kHz/25 kHz
136–174 MHz 6.25 kHz/12.5 kHz/20 kHz

This compliance is based on conformity with the following harmonised
standards, specifications or documents:

1
Authorized representative name

Y. Furukawa
General Manager

3
4

i) EN 301 489-1 v1.4.1 (August 2002)
ii) EN 301 489-5 v1.3.1 (August 2002)
iii) EN 300 086-2 v1.1.1 (March 2001)
iv) EN 301 166-2 v1.1.1 (December 2001)
v) EN 300 219-2 v1.1.1 (March 2001)
vi) EN 300 113-2 v1.3.1 (December 2003)
vii) EN 60950-1: 2001
viii) EN 50385: 2002

5
Signature

6
7
8

DECLARATION
OF CONFORMITY
We Icom Inc. Japan

1-1-32, Kamiminami, Hirano-ku
Osaka 547-0003, Japan

UHF REPEATER

Type-designation:

iC-fr6100/ur-fr6100

Version (where applicable):

400–470 MHz 6.25 kHz/12.5 kHz/25 kHz
400–470 MHz 6.25 kHz/12.5 kHz/20 kHz

This compliance is based on conformity with the following harmonised
standards, specifications or documents:
i) EN 301 489-1 v1.4.1 (August 2002)
ii) EN 301 489-5 v1.3.1 (August 2002)
iii) EN 300 086-2 v1.1.1 (March 2001)
iv) EN 301 166-2 v1.1.1 (December 2001)
v) EN 300 219-2 v1.1.1 (March 2001)
vi) EN 300 113-2 v1.3.1 (December 2003)
vii) EN 60950-1: 2001
viii) EN 50385: 2002

0168
Düsseldorf 25th Feb. 2008
Place and date of issue

Authorized representative name

Y. Furukawa
General Manager

9
10
11
12
13
14
15
16
17
18

Signature

19
20
21
12

< Intended Country of Use >

AT
FI
IT
PL
GB
RO

BE
FR
LV
PT
IS
TR

CY
DE
LT
SK
LI
HR

CZ
GR
LU
SI
NO

DK
HU
MT
ES
CH

EE
IE
NL
SE
BG

1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2008:06:20 15:56:09+09:00
Metadata Date                   : 2008:06:20 16:14:50+09:00
Modify Date                     : 2008:06:20 16:14:50+09:00
Creator Tool                    : Adobe InDesign CS2_J (4.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 5058 bytes, use -b option to extract)
Instance ID                     : uuid:cef5aacb-44df-48e4-b7ed-2baac4bc55fa
Document ID                     : adobe:docid:indd:1a8426d5-3e91-11dd-9ff0-ed46f8bec6d8
Rendition Class                 : proof:pdf
Derived From Instance ID        : 1a8426d4-3e91-11dd-9ff0-ed46f8bec6d8
Derived From Document ID        : adobe:docid:indd:60b108e5-1ca8-11dd-a391-acf71b93d0d9
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:827D12C5CDA3DC118A27FE54C84FAC4F, uuid:F502E6EC57E6DC11963AD85A6E5F03D6, uuid:363CC3B26F87DC118CA19C8D05678902, uuid:F51DDD9E0BA3DC119767C8AFA55D6FD7, uuid:371084543DA9DC11A6C9A9EA9F52D88D, uuid:F71DDD9E0BA3DC119767C8AFA55D6FD7, uuid:F407E829E6C7DC11A979DA357F4226DF, uuid:18130D1E0391DC118B8AB4E9A3FBD2E0, uuid:78383A9FC4A7DC11BEF9EF7F649714C8, uuid:F507E829E6C7DC11A979DA357F4226DF, uuid:083FB7EEFA8BDC1192CF91DE6DFE803E, uuid:996CB273748BDC119E80BA04527483A4, uuid:3B4357D3C198DC11A8FEDB1C550DF9E3, uuid:3B37339AB61CDD119A79BEED66523CD8, uuid:58766A698F1CDD119A79BEED66523CD8, uuid:0AFE5F87E4A9DC11B0FA9168314B9EC7
Manifest Reference Document ID  : uuid:F42A099ACDA3DC118A27FE54C84FAC4F, uuid:831FBA63F996DC11AAF19A85BF48F094, uuid:1A8D40A68D86DC119C47E90C5FFBD740, uuid:31478A937986DC11B3EFCB13F2E164A8, uuid:61B1A4099386DC119C47E90C5FFBD740, uuid:158D40A68D86DC119C47E90C5FFBD740, uuid:00BB9C269F86DC119C47E90C5FFBD740, uuid:362C1057DB90DC118B8AB4E9A3FBD2E0, uuid:43DD75266B87DC11BC6AE0AC89C5C632, uuid:49135DC90897DC118BDAA7D435DF4AB2, uuid:D94511D1728BDC11BF4BDD0AA23B1E4E, uuid:956CB273748BDC119E80BA04527483A4, uuid:801FBA63F996DC11AAF19A85BF48F094, uuid:70257066E4EBDC1199ABCB43407662C7, uuid:70257066E4EBDC1199ABCB43407662C7, uuid:09FE5F87E4A9DC11B0FA9168314B9EC7
Format                          : application/pdf
Title                           : IC-FR5100/FR6100 Instruction Manual
Description                     : VHF/UHF FM REPEATER
Creator                         : Icom Inc.
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Page Count                      : 16
Subject                         : VHF/UHF FM REPEATER
Author                          : Icom Inc.

EXIF Metadata provided by EXIF.tools

Icom Ifr5100 Users Manual IC FR5100/FR6100 Instruction

Navigation menu

Versions of this User Manual:

Views

Navigation