Ideal Lighting CREE Lighting CWC WALL SWITCH User Manual Installation

Download:
Mirror Download [FCC.gov]
Document ID	2367837
Application ID	83B20yqTC1CM6Fj9JqCs7g==
Document Description	Installation
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	40.89kB (511133 bits)
Date Submitted	2014-08-24 00:00:00
Date Available	2014-08-24 00:00:00
Creation Date	2014-08-11 10:00:15
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2014-08-11 10:00:18
Document Title	Cree Controls Series Installation Instructions: Wireless Dimmer and Switch
Document Creator	Adobe InDesign CS6 (Windows)

Cree Wireless Wall Controls With SmartCast™ Technology
Wireless Dimmer and Wireless Switch
Includes: CWD-CWC-XX and CWS-CWC-XX
INSTALLATION INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. Before installing wall controls turn off the power at the circuit breaker.
2. These wall controls must be installed in accordance with the national and
local building codes and electrical wiring codes including wiring methods
and wiring connections. If you are not familiar with these codes and
requirements, consult a qualified electrician.
3. Indoor use only and suitable for damp locations.
4. Any changes or modifications to these devices not explicitly approved by
manufacturer could void your authority to operate this equipment.
WIRELESS DIMMER
CWD-CWC
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
•
Voltage: 120-277V, 60Hz
•
Depth in Wall: 1.5"
•
For ease of installation, Cree recommends the use of a deep wall box.
WIRELESS SWITCH
CWS-CWC
On
Dimming
Up
On
LED
LED
Off
Off
Dimming
Down
UNIT DESCRIPTION
The Cree Wireless Wall Controls are used with other
SmartCast™ Technology enabled devices to provide wireless
control of LED luminaires. The Cree Wireless Wall Controls
provide on, off, and dimming control options.
WALL CONTROLS FEATURES
•
The Cree Wireless Dimmer supports on, off, and
dimming controls. See Figure 1.
•
The Cree Wireless Switch supports on and off, controls.
See Figure 2.
LOAD TYPES
Cree Wall Controls support Cree SmartCast™ Technology
enabled devices only.
1 of 3
LPN000180_H
Wall Control Troubleshooting
Issue
Wall Control LED does not
blink in a 2-blink sequence
prior to OneButton™ Setup
NEUT
GND
Wall Control will not join a
network
LINE
SUPPLY
LEADS
Resolution
Check wiring
(LINE/NEUT/GND required)
Reset Device and verify 2-blink sequence
for the LED
Check wiring (NEUT required)
NOTE: LED may illuminate if NEUT not
connected
Reset Device and verify 2-blink sequence
for the LED
Replaced existing Wall
Control and fixtures will not
turn on
Check Wiring (each fixture shall be wired
with constant HOT)
Wall Control will not control
fixtures
Check group assignments with
Configuration Tool
INSTALLATION
RESET WALL CONTROLS
NOTE: For ease of installation, Cree recommends using a deep
wall box.
STEP 1:
STEP 1:
Disconnect power to circuit by turning circuit breaker OFF
before installation.
STEP 2:
Press/Hold (approx 30 sec) ON paddle until the LED flashes
fast.
STEP 2:
Briefly release the paddle for less than
1 sec (Fast flashing continues)
If necessary remove existing wall plate and switch.
STEP 3:
STEP 3:
Press/Hold ON paddle for 1 sec until fast flashing stops. If
the blue LED does not respond with the two-blink sequence,
please repeat the RESET procedure.
Strip existing wires ½". If two wires will be connected to the
same terminal on the CWD-CWC or CWS-CWC device, both
wires must be the same gauge (12AWG or 14AWG).
STEP 4:
Wire the LINE (black), NEUTRAL (white), and GND (green or
bare) supply wires to the corresponding pigtail leads on the
CWD-CWC or CWS-CWC, as shown in Figure 3.
NOTE: If replacing an existing wall switch, the wall control shall
be wired as instructed; however, the switched power to the
load must also be tied directly to the AC supply leads.
CLEANING
Clean using a cloth dampened only with water and a little mild
detergent. Use of solvents or hydrocarbon-based cleaners may
cause permanent damage.
STEP 5:
Attach the wall plate (reference the wall plate instruction
sheet).
STEP 6:
Switch the circuit breaker ON.
STEP 7:
Press and release the OFF paddle. The blue LED should blink
twice and then go off. If the blue LED does not respond with
the two-blink sequence, please follow the RESET instructions
to return the wall control to factory defaults.
2 of 3
LPN000180_H
FCC NOTICE
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation. Any
changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the device.
This device has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the device is
operated in a commercial environment. This device generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
Operation of this device in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at his own expense.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada licence-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference
that may cause undesired operation of the device. In addition,
this device complies with ICES-003 of the Industry Canada (IC)
Regulations.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur
de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le
fonctionnement.
In addition, this device complies with ICES-003 of the
Industry Canada (IC) Regulations.
© 2013 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change. See
www.cree.com/lighting/products/warranty for warranty and specifications. Cree® and the Cree logo are
registered trademarks, and SmartCast™ and OneButton™ are trademarks of Cree, Inc.
3 of 3
www.cree.com/lighting
LPN000180_H

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Instance ID                     : uuid:7e58e8e3-d8b4-4925-a887-8a030119d155
Original Document ID            : adobe:docid:indd:119000e1-ac16-11dd-a4cf-b36b331595a3
Document ID                     : xmp.id:1BDCE42D6821E411A0E4B76455875180
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:1ADCE42D6821E411A0E4B76455875180
Derived From Document ID        : xmp.did:1ADCE42D6821E411A0E4B76455875180
Derived From Original Document ID: adobe:docid:indd:119000e1-ac16-11dd-a4cf-b36b331595a3
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2014:08:11 10:00:15-05:00
Create Date                     : 2014:08:11 10:00:15-05:00
Modify Date                     : 2014:08:11 10:00:18-05:00
Metadata Date                   : 2014:08:11 10:00:18-05:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Format                          : application/pdf
Title                           : Cree Controls Series Installation Instructions: Wireless Dimmer and Switch
Description                     : Cree Wireless Dimmer and Wall Switch- Cree Controls Installation Instructions
Subject                         : Installation Sheet, instruction, LED, light, luminaire, Cree, safety, electrical connections, shock, wiring, connections, drive current, wall controls
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 3
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools