Ideal Lighting CREE Lighting LN4 Wireless 2.4 GHz module User Manual

Cree, Inc Wireless 2.4 GHz module

User Manual

LN4 Series Cree SmartCast™ Technology Wireless Control ModuleIncludes: LEA02109X0001LPN00303X0001A0_A1 of 1INSTALLATION INSTRUCTIONSINSTRUCTIONS D’INSTALLATIONwww.cree.com/lighting© 2015 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change. See www.cree.com/lighting/products/warranty for warranty and specifications. Cree® is a registered trademark, and the Cree logo is a trademark of Cree, Inc.IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should always be followed including the following:READ AND FOLLOW ALL SAFETY INSTRUCTIONS1. CAUTION - risk of shock. Disconnect power before servicing. ATTENTION - risque de choc. Couper l’alimentation avant l’entretien.2. Any changes or modications to these devices not explicitly approved by manufacturer could void your authority to operate this equipment.SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCESTEP 1:Solder Control Model, LEA02109X0001, into location J67 on driver board, LEA0261X0001. STEP 2:Turn power on. The new control module is correctly installed if the Blue LED displays a 2 blink sequence. NOTE: If the blue LED does not respond with the two-blink sequence, please follow the RESET instructions to return the control module to factory defaults.STEP 3:On the Configuration Tool, select “Replace Devices” from the “Advanced” menu and follow the on-screen directions.. This will remove old device(s) from the network.RESETNOTE: The Blue LED is located behind the reset button on the luminaire. The button with illuminate blue when the Blue LED is active. STEP 1: Actuate RESET button. Push and hold (approximately 10 sec), LED on control module will blink fast. STEP 2: Release for 1 sec. STEP 3: Press/Hold RESET button for 0.5 sec. Light will go to full bright and the Blue LED on the control module should be in a 2 blink sequence. FCC NOTICETo comply with the FCC RF exposure compliance requirements, this device and its antenna must not be co-located or operating to conjunction with any other antenna or transmitter.This equipment should be installed and operated with minimum distance 5cm between the radiator & your body. No other antenna is authorized for use with this product.FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved could void your authority to use this equipment.This device complies with Part 15 of the FCC Rules. Operation to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operationThis device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the device is operated in a commercial environment. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.The LED in the front of this device operates within Risk Group 1 levels per IEC 62471.INDUSTRY CANADA STATEMENTThis device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. In addition, this device complies with ICES-001 of the Industry Canada (IC) Regulations.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.TO INSTALL:LABEL REQUIREMENT FOR END PRODUCT:The final end product must be labeled in a visible area with the following "Contains TX FCC ID:2ACQ6-LN4 " and “Contains TX IC ID: 11481A-LN4”RF Exposure NoticeTo comply with the FCC/IC RF exposure compliance

Navigation menu