Identec Solutions ILR-IB2W Wristband Tag User Manual

Identec Solutions AG Wristband Tag

User Manual

i-B2X W, Wristband Tag Manual
Wristband Tag Manual Page 2 of 11 Proprietary Notice This document contains confidential information proprietary to IDENTEC SOLUTIONS and may not be used or disclosed to other parties in whole or in part without prior written authorization from IDENTEC SOLUTIONS. Disclaimer and Limitation of Liability IDENTEC SOLUTIONS AG and its affiliates, subsidiaries, officers, directors, employees and agents provide the information contained in this Manual on an “as-is” basis and do not make any express or implied warranties or representations with respect to such information including, without limitation, warranties as to non-infringement, reliability, fitness for a particular purpose, usefulness, completeness, accuracy or up-to-dateness. IDENTEC SOLUTIONS shall not in any circumstances be liable to any person for any special, incidental, indirect or consequential damages, including without limitation, damages resulting from use of or reliance on information presented herein, or loss of profits or revenues or costs of replacement goods, even if informed in advance of the possibility of such damages. Trademarks “IDENTEC SOLUTIONS”, “Intelligent Long Range”, “ILR” and the stylized “i” are registered trademarks and “i-Q”, “i-D”, “i-B”, “i-CARD”, “i-PORT”, “i-LINKS”, “Solutions. It’s in our name.”, “Smarten up your assets” are trademarks of IDENTEC SOLUTIONS, Inc. and/or IDENTEC SOLUTIONS AG. Copyright Notice Copyright © 2007 IDENTEC SOLUTIONS. All rights reserved. No part of this document may be reproduced or transmitted in any form by any means, photographic, electronic, mechanical or otherwise, or used in any information storage and retrieval system, without the prior written permission of IDENTEC SOLUTIONS. Reg. No. IM.0756.EN Issue 0a / December 2008 – 02. December 2008 – IDENTEC SOLUTIONS AG, Millenium Park 2, 6890 Lustenau, Austria Phone: +43 5577 87387- 0, Fax: +43 5577 87387-15 E-Mail: info@identecsolutions.at www.identecsolutions.com Subject to alteration without prior notice. © Copyright IDENTEC SOLUTIONS 2007 Printed in Germany
i-B2X W Page 3 of 11 Contents 1 RADIO FREQUENCY COMPLIANCE STATEMENT...........................................................4 2 INTRODUCTION ...........................................................................................................5 2.1 PREPARATIONS ............................................................................................................5 2.2 RECOMMENDED PROCEDURE............................................................................................5 2.3 SCOPE OF THIS DOCUMENT .............................................................................................5 2.4 SAFETY INSTRUCTIONS ..................................................................................................5 2.5 RESPONSIBILITY...........................................................................................................5 2.6 ASSOCIATED DOCUMENTS...............................................................................................5 2.7 SCOPE OF DELIVERY—VISUAL INSPECTION..........................................................................6 2.8 OPTICAL IDENTIFICATION OF THE TAG ...............................................................................6 3 INITIAL OPERATION....................................................................................................7 4 TAG MOUNTING TECHNIQUES .....................................................................................8 5 MAINTENANCE .............................................................................................................9 5.1 GENERAL ...................................................................................................................9 5.2 PRECAUTIONARY MAINTENANCE........................................................................................9 5.3 RETURNS ...................................................................................................................9 6 TECHNICAL DATA .......................................................................................................10
Wristband Tag Manual Page 4 of 11 1 Radio Frequency Compliance Statement FCC Compliance Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
i-B2X W Page 5 of 11 2 Introduction 2.1 Preparations This installation manual must be read carefully prior to starting the installation. The described installation works assume that installation materials like cable, antenna and tag holder etc are available. 2.2 Recommended Procedure 1. Check the Scope of Delivery according to the Bill of Delivery 2. Read this manual completely 3. Do the initial operation for every single tag 4. Mount the tags 5. An additional performance check of the tags and a system test can now be done 2.3 Scope of this Document This document is the user’s manual of the model i-B2X W tag. This document is intended only for mechanical installation rsp. everyday use. Both mounting techniques described in this document are suitable for ATEX conformity. 2.4 Safety Instructions Operational Safety The device described in this manual is for exclusive operation by trained employees. The correct and safe use of these systems assumes that operating and service personnel follow the safety measures described in the manual alongside the generally acceptable safety procedures. If there is a possibility that safe operation cannot be guaranteed the system must be switched off and secured against accidental use. Then the service unit responsible must be informed. Do not open the housing There is no need to open the housing. There are no user serviceable parts inside. Set-up and configuration during initial operation is done wireless with the built-in air interface. 2.5 Responsibility IDENTEC SOLUTIONS is not responsible for any errors occurring in this document. 2.6 Associated Documents • ID.0669.EN_i-B2X W — Wristband tag Datasheet
Wristband Tag Manual Page 6 of 11 2.7 Scope of Delivery—Visual Inspection Check delivery whether it is complete and for any damages. If the delivery is not complete or damaged immediately inform the carrier. The dispatch and service organization of IDENTEC SOLUTIONS should also be informed to facilitate the repair or exchange of the system. 2.8 Optical Identification of the Tag The label is on the rear side of the tag, protected by the wristband. In order to inspect it slightly lift up the wristband between the two loops of the tag housing. View onto the label Model designation Type designation Serial number Manufacturer info ATEX reference
i-B2X W Page 7 of 11 3 Initial Operation Important Note Do not open the housing! Configuration is done using the built-in air interface of the i-B2X W. Configuration The i-B2X W is configured using the i-PROG MB programming device. Things to be configured • The ping rate: from 0.5 to 60 seconds in steps of 0.5 seconds
Wristband Tag Manual Page 8 of 11 4 Tag Mounting Techniques The tag is carried as every standard wristwatch. The band should not be too loose. This avoids that the tag slides down over the wrist and prevents possible injury. For maximum convenience put the end of the wristband under the loop. Now adjust the loop to avoid too much of the band to stick out.
i-B2X W Page 9 of 11 5 Maintenance 5.1 General In principle, the ILR system is maintenance-free. When correctly installed it operates for many years without any problems. 5.2 Precautionary Maintenance Regular checking to the system is recommended. Make sure that the housing of the tag has no damage. If there are any damages as holes or cracks, the tags should be replaced and returned to IDENTEC SOLUTIONS immediately. Regular checking of all ports and cables belonging to the system is recommended. Unstable connections could lead to damage and malfunctions of the system and therefore should be repaired as soon as possible. A Brief Checklist • Are all housings intact? • Are all cables intact? • Are all connectors intact? • Are all connectors securely fastened? • Are all screws still tight? • Is there suddenly a malfunction at a specific unit? 5.3 Returns Parts or main components returned for repair or exchange must be handled with great care. PC cards must be returned in the appropriate ESD-protecting packaging material. All returns should include a completed returns form (see appendix) and be sent to the local distributor or to: IDENTEC SOLUTIONS AG Service Department Millenium Park 2 6890 Lustenau AUSTRIA / AUTRICHE
Wristband Tag Manual Page 10 of 11 6 Technical Data Operating Data Long-Range RFID (ILR, Beacon Technology) Read range Up to 30 m (90 ft) in free air Operating frequency 868 MHz (EU) or 915 MHz (NA) ISM band Operation mode Transmits a pre-programmed data string in regular intervals Repetition rate (ping rate) 0,5 – 60 seconds, adjustable in steps of 0,5 seconds Transmit power < 1 mW Compatibility i-PORT 4B, i-PORT MB, i-CARD CF B Electrical Data Power supply Lithium battery (not replaceable) Battery lifetime expectancy 4 years @ 2 seconds ping rate Configuration The transponder is configured using the i-PROG MB at a distance of max. 5 cm. Ping rate Configurable from 0.5 to 60 seconds in steps of 0.5 seconds User data 9 Bytes (user definable) Environmental Conditions Operating temperature –30 to +70 °C (–22 to +158 °F) Shock 50 G, 3 times acc. DIN IEC 68-2-27 several times onto concrete floor from 1 m height Vibration 3 G, 20 sine wave cycles, 5 to 150 Hz, DIN IEC 68-2-6 5 G, noise 5 to 1.000 Hz, 30 minutes DIN IEC 68-2-64 Mechanical Data Dimensions 43 × 38.5 × 14.5 mm (1.7 × 1.5 × 0.57 inches) Casing Plastics Mass 40 g Protection class IP 65 Certifications EMC CE (EN 300 220-1, -3; ETSI EN 301 489-1, -3), FCC Part 15 (US), Industry Canada ATEX/IECEx certificates II 1 G Ex ia IIC T4, Certificate Number: DNV-2008-OSL-ATEX-42107
i-B2X W Page 11 of 11 Dimensional Drawing

Navigation menu