User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1083609 |
| Application ID | 2JeVJPGVWyhYjCC6AzIMYQ== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 52.68kB (658504 bits) |
| Date Submitted | 2009-03-20 00:00:00 |
| Date Available | 2009-03-20 00:00:00 |
| Creation Date | 2009-03-16 12:01:32 |
| Producing Software | Acrobat Distiller 9.0.0 (Windows) |
| Document Lastmod | 2009-03-16 12:01:32 |
| Document Title | Microsoft Word - SDI010-MOD OEM Integration Manual v1.0.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | calai |
SDI010-MOD OEM Integration Manual Version 1.0 SDI010-MOD OEM Integration Manual v1.0 SCOPE The scope of this document is to explain the fine points of integrating the SCM SDI010 Rev 0.2 dual interface reader modules into other devices. Figure 1: Top View of SDI010-MOD Figure 2: Bottom View of SDI010-MOD Page 2 of 4 SDI010-MOD OEM Integration Manual v1.0 MOUNTING It is recommended that the module is mounted so that the antenna that runs along the periphery of the PCBA is parallel to the card placement position inside the device. The board has two mounting holes located diagonally across. It is recommended to use nylon (non-metallic) screws in these mounting holes. It is also recommended that there is no metal in proximity of the antenna to ensure that signal strength is not degraded. CABLES & CONNECTORS The board has two external connectors: one host USB header (J1) and a control header (J2) to enable/disable the contact and/or contact less operation. The headers J1 and J2 are located on the top of the board. The bottom of the board has the ISO7816 contact connector below which the card guide mechanism has to be placed. It is recommended that none of the cables pass over the antenna region. LABELING If the module is integrated in such a way that the label is not visible outside, then the integrator has to display a exterior label referring to the enclosed module. The exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: MBPSDI010MOD02” or “Contains FCC ID: MBPSDI010MOD02”. Any similar wording that expresses the same meaning may be used. PRODUCT DOCUMENTATION The end product documentation should include the FCC ID of the device and also include the wording “The device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received including interference that may cause undesired operation. TROUBLE SHOOTING 1. Unit does not power up Check to ensure that the host USB cable is plugged in at proper orientation. 2. Host displays message that device is asking for more power The device draws power from the host through the USB connector. The maximum power draw is 150mA at 5V. So the device has to be plugged into a root port or into a port on a self-powered hub. This message occurs when device is plugged into a bus-powered hub. Page 3 of 4 SDI010-MOD OEM Integration Manual v1.0 3. Device appears with yellow bang (!) on device manager This could happen when drivers are not found for this device or when drivers fail to load. The drivers for this device are available on Windows Update or can be downloaded from http://www.scmmicro.com. If the failure is due to driver load failure, then the reason for driver load failure can be inferred from the device manager message at the General tab. 4. Contact less cards are not detected This could happen when module is placed in proximity to something made out of metal. Ensure that there is not metal in proximity between the antenna and the card. 5. Contact card is not detected Check the connections on the two pin header. The terminals should be continuous when a card is inserted. 6. Contact card cannot be read Ensure that the cables between (both five and four pin) headers and the smart card connector are of same length and type. DISCLAIMER The module has been tested and determined to be compliant with the FCC rules for intentional radiators. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Page 4 of 4
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Author : calai Create Date : 2009:03:16 12:01:32-07:00 Modify Date : 2009:03:16 12:01:32-07:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Creator Tool : PScript5.dll Version 5.2.2 Producer : Acrobat Distiller 9.0.0 (Windows) Format : application/pdf Title : Microsoft Word - SDI010-MOD OEM Integration Manual v1.0.doc Creator : calai Document ID : uuid:38ddde20-7c61-48b1-b19e-00bffcbcaad0 Instance ID : uuid:53b18986-9298-430c-9251-297f2fb06ce2 Page Count : 4EXIF Metadata provided by EXIF.tools