Ihome Ih55 Users Manual

iH55 iH55_IB_01030840296_32

iH55 to the manual 4b3bccca-5f64-ab04-b53a-9560e9947e57

2015-01-21

: Ihome Ihome-Ih55-Users-Manual-348562 ihome-ih55-users-manual-348562 ihome pdf

Open the PDF directly: View PDF PDF.
Page Count: 14

iH55 IB_010308.fh10 2/12/08 10:05 AM Page 1
Model iH55
The Home System
For Your iPod®
Questions? Visit www.ihomeaudio.com
Music
Photos
Extras
Settings
Shuffle Songs
Backlight
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 2
Table of Contents
Quick Start ........................................................................................................................................................................1
Controls and Indicators / iH55 Display ..........................................................................................................................2
Using the iH55 ...............................................................................................................................................................3-4
Replacing iH55 Backup Batteries....................................................................................................................................5
Install/Replace Backup Battery
Batteries information
Using the Remote Control Unit.......................................................................................................................................5
A Consumer Guide to Product Safety............................................................................................................................6
Troubleshooting ...............................................................................................................................................................7
Solucionando problemas ................................................................................................................................................9
Warranty Information .....................................................................................................................................................11
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 3
Package Contents
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits
provide reasonable protection against radio and TV interference in a residential area.
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference
you can try one or more of the following corrective measures:
• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and the radio or TV.
• Use outlets on different electrical circuits for the equipment and the radio or TV.
Consult your dealer or an experienced radio/television technician if the problem still exists.
Modifying or tampering with your system’s internal components can cause a malfunction and might invalidate the system’s
warranty and void your FCC authorization to operate it.
This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this
device does not cause harmful interference.
Package contains:
• iH55 home system
• Remote control
• AC adaptor
• AM antenna
• CD/MP3 Patch cord
• 3 dock inserts (for iPod nano and iPod with video 30 GB and iPod with video 60GB and 80GB)
• 2 switchable face panels
A consumer Guide to Product Safety
Maintenance
• Place the unit on a level surface away from sources of direct sunlight or excessive heat.
• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should
be placed between it and the furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzine, thinner
or similar materials can damage the surface of the unit.
FCC Information
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 4
1
iH55 quick start
Attach AC adaptor cable to
jack on back of the iH55 and
plug the other end into a
wall socket.
Select the dock insert for your
iPod® model from the chart
below and place insert in dock.
To avoid damage, never dock
your iPod without an insert .
Snap AM antenna into provided
stand, then plug antenna cable
into socket on back of iH55.
Move antenna 12” away.
•Press & hold the Time Zone
button on back until display
flashes
•Turn the Set Wheel to select
your time zone
•Press the Time Zone
button again.
• Move the DST switch on back
of unit to +1 or -1 (adds or
subtracts an hour)
Insert iPod into dock (iPod® must
not be in a “skin” or case). Press
iPod Button on iH55. iPod will
charge while docked.
NOTE: If you do not have an insert
for your iPod, please visit an Apple
store, www.ihomeaudio.com, or
call iHome toll free at 800-288-2792
to purchase one.
1:power 2:antenna 3:inserts
4:time
Press the Radio button. Press
AM/FM button to select your
band. Turn the Set Wheel to
tune in a station.
6:radio
thin iPod with video (30 GB)
thin (30 GB) iPod with video
thin (80 GB) iPod classic
iPod with video (60,80 GB)
thick (60,80 GB) iPod with video
thick (160 GB) iPod classic
Use this insert
For this iPod
3rd Gen nano
3rd Gen nano
5:iPod
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 5
iPod radio am/fm sleep
alm. on/off alm. set wake-to alm. reset
snooze/dimmer
volume
power off
AC Adaptor Jack Line in Jack
Clock Adjust Button
Line Out Jack
FM Antenna
AM Loop Antenna socket
DST Switch
DC 15V 1200mA
time zone clock adj.
DST
-1 +1line inline out
am antenna
2
Controls and Indicators
iH55 Display
Time Zone Button
Volume Wheel
Dock
iPod Button
Set Wheel
Radio Button
AM/FM Select Button
Sleep Button
Alarm On/Off Button
Alarm Set Button
Wake-To Button
Alarm Reset/Power Off Button
Snooze/Dimmer Button
Alarm Armed
Daylight Saving Time
Indicator
Battery Low Indicator Time/Alarm Display PM Indicator Sleep Display
Wake To Indicator:
iPod, Radio, Buzzer,
Radio Frequency AM/FM Indicator
iPod Indicator
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 6
3
Using the iH55
Connect iH55 to Power Source
a) Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120v wall socket. The iH55 does not
operate on batteries.
Setting the Clock
a) Press and hold the Time Zone Button until the display flashes.
b) Turn the Set Wheel to select your time zone.
c) Press the Time Zone Button again. The clock will display the current time in your time zone.
d) To adjust the time for Daylight Saving Time, slide the DST switch to +1 to advance the time 1 hour.
Slide to -1 to turn the clock back 1 hour.
To Set Clock Manually
a) Press and hold the Clock Adjust Button. The clock display will flash.
b) Turn the Set Wheel until the current time is displayed (a PM indicator appears when time is set to PM; there is no AM indicator).
c) Press the Clock Adjust Button to accept the time. The year display will flash.
d) Turn the Set Wheel to adjust the year and press the Clock Adjust Button. The date display will flash.
e) Turn the Set Wheel to adjust the date and press the Clock Adjust Button. Two beeps will indicate clock setting is complete.
Using the Alarm
Setting the Alarm
a) Press and hold the Alarm Set Button until the alarm time flashes.
b) Turn the Set Wheel to set the alarm time (a PM indicator appears when time is set to PM; there is no AM indicator).
c) Press Alarm Set again. Alarm is now armed, indicated by the alarm clock icon and alarm source icon.
d) At any time, press the Wake-To Button repeatedly to select an alarm source to wake to: iPod, radio or buzzer.
Turning Alarm Function ON and OFF
a) Press the Alarm On/Off Button to arm or disarm alarm function. When armed, alarm icon appears in display.
Resetting the Alarm to Come on the Next Day
a) When the alarm is sounding, press the Alarm Reset/Power Off Button to stop alarm and reset it to come on the following day.
Snooze
a) Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes later. Snooze
can be pressed several times during the 1 hour alarm cycle.
Sure Alarm
The iH55 has a sure alarm feature so in the event of a power failure, the buzzer alarm will still sound (if backup batteries are installed).
iPod
Playing and charging your iPod
a) Place proper insert for your iPod (see insert table on page 1) in Dock, then gently dock iPod. When docked, iPod will charge
until fully charged. The iPod will not overcharge. Note: To remove insert, use thumbnail in slot on back of insert and pull up.
b) Press the iPod Button to play iPod, and again to pause.
c) Turn Volume Wheel to adjust iH55 volume up or down
d) Press
Alarm Reset/Power Off Button to turn iH55 and iPod off.
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 7
4
Using the iH55
Radio
Setting up Antennas
a) Snap AM loop antenna into provided stand, then plug antenna cable into AM Loop Antenna socket on back of unit.
Move antenna 12” away from unit for best reception.
b) Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas.
Tuning and Playing the Radio
a) Press the Radio Button to select radio play mode.
b) Press the AM/FM Select Button to select AM or FM radio band.
c) Turn the Set Wheel to tune radio to desired station.
d) Turn the Volume Wheel to adjust iH55 volume up or down.
e) Press
Alarm Reset/Power Off Button to turn iH55 and iPod off.
Using the Line-in and Line-out Jacks
a) Use an audio patch cord to play nondocking iPods or other audio devices through the iH55 Line-in Jack (one end in the
device’s line out or headphones jack, the other in the iH55 line in jack). Make sure there is no iPod docked in the iH55 when
using the line-in jack. Press the iPod Button until AUX appears on the display.
b) Use the Line Out Jack to connect the iH55 to the line-in jack of other audio devices such as a tape recorder or amplifier.
The Volume Wheel of the iH55 does not control line-out volume (adjust on attached device instead).
Using Sleep Mode
Sleep mode lets you sleep to your iPod or the radio, gradually lowering the volume until the unit shuts off at the selected time.
a) Press the Sleep Button to select an amount of time before the iH55 will turn off: 120, 90, 60, 30 or 15 minutes.
b) Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting).
Using Dimmer
a) Press the Snooze/Dimmer Button during normal operation to adjust brightness of LCD display.
Changing the Speaker Grille
The iH55 comes with 3 detachable speaker grilles (one is already installed).
a) To remove the speaker grille, grip the bottom edge of the grille on either
side and gently pull forward until the bottom edge is free of the unit.
Grip the the left edge of the grille and gently pull out the grille from the left
of the unit. Do the same on the right and release the grille.
b) To replace the speaker grille into the unit, simply line up the grille and
press firmly into place. Make sure the grille is placed properly so it does not
vibrate.
NOTE: DO NOT TOUCH EXPOSED SPEAKERS WHEN GRILLE IS
REMOVED
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 8
Install/Replace the Remote Control Battery
The remote control battery is already installed at the factory. When the remote control stops
operating or its range seems reduced, replace the battery with a new one.
1. The battery door is located on the back end of the unit.
2. Squeeze notched tab A while pulling battery door latch B to release the battery door latch
and take out the battery holder.
3. Insert a “CR2032” 3-volt lithium battery. Make sure the polarity (the + and – side of the
battery) is correct.
4. Replace the battery holder back in the remote control.
NOTE: PLEASE DISCARD BATTERIES PROPERLY
The iH55 uses a backup battery system to provide continuous alarm operation and clock settings in the event of a power failure. If the Battery
Low Icon located on the left of the display is flashing, it is time to replace the backup batteries.
Please make sure the AC adaptor is connected,
otherwise all settings may be lost during battery replacement.
Open the battery compartment cover located on the bottom of the unit. Insert 2 “AA” batteries
as indicated. We recommend the use of alkaline batteries for longer life.
Batteries information:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium) batteries.
Radio Button ...................................Selects Radio function
iPod Play/Pause Button...................Selects iPod and plays track. In play mode, press to pause
Power On/Off Button .......................Turns iH55 ON or OFF or resets alarm when alarm is sounding
Button
Button ........................................Skip to previous or next track when iPod is playing, or
HOLD to scan current playing track. In radio mode, press
to tune stations. HOLD to scan radio stations.
AM/FM Select Button ......................Selects AM or FM radio band
Snooze/Dimmer Button ...................Snooze mode when alarm sounds, otherwise dims display
Volume + Button..............................Raises volume level
Volume _ Button..............................Lowers volume level
Using The Remote Control Unit
Installing/Replacing iH55 Backup Batteries
A
B
The Remote Control controls basic functions on the iH55 and certain iPod® functions when the iPod® is docked in the iH55.
For best results, aim the remote control towards the grille at the lower right-hand corner of the display.
Battery
door
latch
5
AA
AA
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 9
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety.
However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating
instructions carefully before installation and use, and keep these instructions handy for future reference. Take special
note of all warnings listed in these instructions and on the unit.
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,
laundry tub, swimming pool or in a wet basement.
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation.
For example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings.
Also, it should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of
air through the ventilation openings.
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances
(including amplifiers) that produce heat.
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance.
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them. It is always best to have a clear area from where the cable exits the
unit to where it is plugged into an AC socket.
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for
cleaning instructions.
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any
openings or vents located on the product.
8. Attachments – Do not use attachments not recommended by the product manufacturer.
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or
cable system during a lightning storm or when it is left unattended and unused for long periods of time. This will
prevent damage to the product due to lightning and power-line surges.
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:
A. the power supply cable or plug has been damaged.
B. objects have fallen into or liquid has been spilled into the enclosure.
C. the unit has been exposed to rain.
D. the unit has been dropped or the enclosure damaged.
E. the unit exhibits a marked change in performance or does not operate normally.
12. Antenna – Do not connect an external antenna to the unit (other than that provided).
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the
power cable should be unplugged from the unit to prevent damage or corrosion.
14. Servicing – The user should not attempt to service the unit beyond those methods described in the user’s operating
instructions. Service methods not covered in the operating instructions should be referred to qualified service
personnel.
Questions? Visit www.ihomeaudio.com
A Consumer Guide to Product Safety
6
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 10
iH55 does not turn on AC adaptor isn't plugged into a working wall socket
or not plugged into the power supply jack on back
of the unit
Plug the AC adaptor into a working wall socket and plug the
connector into the supply jack on the unit
iH55 requires a reset If unit is plugged in and doesn't respond, try resetting the unit by following
these steps:
a) remove iPod from dock
b) unplug unit from power source
c) remove back up batteries
d) wait 1 hour, then resume use
iPod does not dock
properly
Using no or wrong iPod insert Make sure the dock insert is the proper fit for your iPod
(see chart on page 1)
iPod didn’t install properly Remove your iPod from the dock and check for obstruction on the
connectors in the dock and on your iPod. Then reseat it in the dock.
Battery Low icon always
flashing
Batteries are weak Replace with new batteries
Batteries were not installed properly Check to make sure the polarity ( + and – ends) matches the diagram
in the battery compartment
iPod does not respond
to the unit/iPod is
playing but no sound
comes out
iPod is not installed properly Remove your iPod from the dock and check for obstruction on the
connectors in the dock and on your iPod. Then reseat it in the dock.
Your iPod software is too old Upgrade software on your iPod. For details visit
http://www.apple.com/ipod/download
iPod is locked up/plays but no sound
comes out
Check the volume setting. Make sure your iPod is working properly before
docking into the unit. Please refer to your iPod manual for details. See
above for software upgrade information.
You may need to reset your iPod. To do so:
1. Toggle the Hold switch to hold position, then off.
2. Press and hold the Menu and center Select buttons at the same time until
Apple logo appears. You may need to repeat this step.
Using 1st or 2nd generation iPod, iPod Shuffle or
other devices.
iH55 cannot control those iPods or other devices.
iPod didn’t charge up iPod is not installed properly Remove your iPod from the dock and check for obstruction on the
connectors in the dock and on your iPod. Then reseat it in the dock.
iPod is locked up/ frozen
iPod battery has problem
Please make sure your iPod is working properly before docking into the
unit. Please refer to your iPod manual for details.
No AM band radio
sound but others OK
AM loop antenna is not connected to the unit Plug the AM loop antenna connector to the jack on the back of the unit
AM band radio is very
noisy
AM loop antenna isn’t located properly Move the AM loop antenna away from the main unit/iPod and rotate it
for best reception
7
Troubleshooting
Solution
Symptom Possible Problem
No sound from iH55 Volume is set too low on iH55 Make sure volume is turned up
Remote Control didn’t
work
Battery weak Replace current battery with new battery
Remote Control is not pointed toward the
iH55 remote sensor
Point the Remote Control toward the iH55 remote sensor (to right of
clock display), move within 10 feet of the unit.
Move unit away from potential sources of external interference such as
computers, modems, wireless devices (routers) or fluorescent light
iH55/iPod performance
is erratic The iH55 is reacting to external interference
iH55 doesn’t respond
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 11
Sound is distorted Volume level is set too high Decrease the volume
Sound source is distorted If the iPod original sound source (MP3) is old or of poor quality, distortion
and noise are easily noticed with high-power speakers. Try a different
audio source such as a music CD.
If you are using an external sound source like older generation of iPod
or iPod Shuffle, try reducing the output volume on the device itself. Also
try turning bass boost OFF.
8
Troubleshooting
Solution
Symptom Possible Problem
Unit/adaptor gets warm
after extended play at
high volume
This is normal Turn unit off for awhile or lower volume
The signal from the line out jack needs amplification. Use powered
speakers/monitors or other amplified audio device.
Can't hear
headphones/speakers
attached to line out jack
Line out jack is not meant for headphones.
Speakers need a power source
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 12
Síntoma
El adaptador de corriente AC no está conectado a
un tomacorriente que funcione o no está conectado
en la parte posterior de la unidad
Conecte el adaptador de corriente a un tomacorriente que funcione
y a la parte posterior de la unidad
La unidad debe ser reprogramada Si la unidad está conectada y no responde, pruebe reprogramarla
siguiendo estos pasos:
a) Quite el iPod de la base
b) Desconecte la unidad del tomacorriente
c) Quite las baterías auxiliares
d) Espere 1 hora y vuelva a probar
No ha colocado el encastre del iPod, o está
utilizando el encastre incorrecto.
Verifique que el encastre sea el apropiado para su iPod
El iPod no encastra correctamente Quite el iPod del encastre y retire la posible obstrucción del
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.
El ícono de batería
baja está
destellando
Las baterías están gastadas Reemplace las baterías
Las baterías no están instaladas
correctamente
Verifique que la polaridad de las baterías (- y +) se encuentren
de acuerdo al diagrama del compartimiento de baterías.
El iPod no se
comunica con la
unidad
El iPod no está instalado correctamente Quite el iPod del encastre y verifique posibles obstrucciones del
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.
Su software es obsoleto Renueve su software. Para mayor información, diríjase a
http://www.apple.com/ipod/download
El iPod no responde Verifique que su iPod funcione correctamente antes de conectarlo
a la unidad. Refiérase al manual de su iPod para más detalles.
Usted tiene un iPod de primera o segunda
generación, un Shuffle u otro tipo de aparato El iH55 no puede controlar estos otros aparatos
Causa Solución
El iPod no carga El iPod no está instalado correctamente Quite el iPod del encastre y retire la posible obstrucción del
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.
El iPod está trabado/no responde
La batería del iPod podría tener algún
inconveniente
Por favor asegúrese de que su iPod funcione correctamente antes
de colocarlo en el encastre. Refiérase al manual de su iPod para
mayor información.
La banda de AM no
suena pero las demás sí
La antena no está ubicada correctamente Aleje la antena de la unidad y gírela para mejorar la recepción
El sonido sale
distorsionado
El volumen se encuentra muy alto Baje el volumen
El sonido sale distorsionado de la unidad
Si está utilizando un iPod de primeras generaciones o un Shuffle,
intente bajar el volumen de su aparato. También intente apagar
el amplificador de bajos
El control remoto
no funciona
Las baterías están gastadas Reemplace las baterías por nuevas
No está apuntando el control remoto hacia el
iH55
Apunte el control remoto hacia el iH55 y manténgase a una
distancia máxima de 10 pies de la unidad.
Si el sonido original de su iPod era de pobre calidad, las
distorsiones y ruidos se harán más notables con los
parlantes de alta potencia. Pruebe utilizar otra fuente de
audio como un CD.
No sale sonido
de su iH55
El volumen del iH55 se encuentra muy bajo Asegúrese de subir el volumen
Solucionando problemas
El iPod no encastra
correctamente
La unidad no
enciende
La unidad no
responde
9
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 13
Síntoma Causa Solución
La unidad recalienta
luego de largos
períodos de uso a
alto volumen
Esto es normal Apague la unidad o baje el volumen
El funcionamiento
del iH55/iPod es
errático.
El iH55 está reaccionando a interferencias
externas. Aleje la unidad de Fuentes potenciales de interferencia externa
como computadoras, modems, ruteadores inalámbricos, luz
fluorescente, etc.
No puede
escuuchar los
auriculares/parlant
es que están
conectados a la
ficha de salida “line
out”
La línea de salida no está diseñada para
auriculares. Los parlantes necesitan una fuente
de alimentación
La señal de salida require amplificación. Utilice parlantes u otra
clase de aparto amplificado.
10
Solucionando problemas
iH55 IB_010308.fh10 2/12/08 10:05 AM Page 14
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from
defects in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies
will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage,
and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service
Center listed below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase
is $30.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries
are the most common cause of problems encountered.
If service is still required:
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($30.00 without proof of purchase).
4. Send the unit prepaid and insured, to the Factory Service Center listed below.
Consumer Repair Department
SDI Technologies Inc.
1330 Goodyear Dr.
El Paso, TX 79936-6420
Disclaimer of Warranty
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may
not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies product.
Questions? Visit www.ihomeaudio.com
Toll Free Customer Service: 1-800-288-2792
iH55IB-060507-B ©SDI Technologies 2007 All rights Reserved Printed in China
Limited 90-Day Warranty Information

Navigation menu