Impex Fitness Tsa 9900 Owners Manual PARTS LIST

Impex-Fitness-Tsa-9900-Owner-S-Manual impex-fitness-tsa-9900-owner-s-manual

: Impex-Fitness Impex-Fitness-Tsa-9900-Owners-Manual-746641 impex-fitness-tsa-9900-owners-manual-746641 impex-fitness pdf

Open the PDF directly: View PDF .
Page Count: 33

Download
Open PDF In Browser	View PDF

NOTE:
Please read all instructions
carefully before using this
product

Table of Contents
Safety Notice
Hardware Pack
Assembly Instruction
Parts List

IRON GRIP STRENGTH
Corner Gym

TSA-9900

Resistance Chart
Warranty
Ordering Parts

Model
TSA-9900
Retain This
Manual for
Reference
08-06-05
OWNER'S
MANUAL

IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966

www.impex-fitness.com
info@impex-fitness.com

TABLE OF CONTENTS
BEFORE YOU BEGIN......................................................................................
IMPORTANT SAFETY NOTICES.....................................................................
HARDWARE PACK……….....….......................................................................
ASSEMBLY INSTRUCTIONS...............................................................…..........
PARTS LIST…………………………………………………………….……….…….
RESISTANCE CHART……………………………………………………………….
WARRANTY.................................................................................................…
ORDERING PARTS.........................................................................................

BEFORE YOU BEGIN
Thank you for selecting the IRON GRIP STRENGTH TSA-9900 CORNER
GYM by IMPEX INC. For your safety and benefit, read this manual
carefully before using the machine. As a manufacturer, we are committed
to provide you complete customer satisfaction. If you have any questions,
or find there are missing or damaged parts, we guarantee you complete
satisfaction through direct assistance from our factory. To avoid
unnecessary delays, please call our TOLL-FREE customer service
number. Our Customer Service Agents will provide immediate assistance
to you.

Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
info@impex-fitness.com
1

1
2
4
7
30
31
32
32

IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your machine. In particular, note the following safety
precautions:

1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the same station.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the machine.
3. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Maximum user’s weight: 300 lbs.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT.
IMPEX INC.
ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
2

WARNING LABEL REPLACEMENT

The warning labels shown here have been placed on the Rear Base and Upper Frame. If the labels are
missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels
in location shown.

3

HARDWARE PACK

4

HARDWARE PACK

5

HARDWARE PACK

6

ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended two or people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Place the Right Base Frame (#1) on a flat surface. Make sure there is enough space around
to assemble the machine.
B.) Insert four Guide Rods (#4) into the holes on the Right Base Frame. Secure each Guide Rod
from the bottom with a M10 x 1” Allen Bolt (#94).
C.) Slide four Ø 2 ½” x 1” Rubber Bumpers (#86) onto the Guide Rods.

DIAGRAM 1

7

STEP 2

(See Diagram 2)

A.) Attach the Left Base and the Power Station Base Frame (#2 & #3) to the Right Base
Frame (#1).
B.) Align the holes and secure them with two M10 x 2 ½” Carriage Bolts (#98), ∅ ¾” Washers
(#109), and M10 Aircraft Nuts (#106).

DIAGRAM 2

8

STEP 3

(See Diagram 3)

A.) Slide fourteen Weight Plates (#54) onto the rear set of Guide Rods (#4). Make sure the
groove on the plates all face toward the front of the machine.
B.) Insert a Selector Rod (#53) into the center holes. Slide a Selector Stem (#34) onto the
two Guide Rods. Slide a Ø 1 ¾” Rubber Bumper (#34) onto the Selector Rod.
C.) Repeat procedures A & B above to install the other fourteen Weight Plates onto the front
two Guide Rods. Make sure the grooves face the back of the machine.

DIAGRAM 3

9

STEP 4 (See Diagram 4)
A.) Do not tighten all Nuts and Bolts in this step until instructed to do so.
B.) Attach the Right Vertical Frame (#5) to the Right Base Frame (#1). Secure it with two M10 x
2 ½” Carriage Bolts (#98), Ø ¾” Washers (#109), and M10 Aircraft Nuts (#106).
C.) Attach the Left Vertical Frame (#6) to the Left Base Frame (#2). Secure it with one M10 x 2
½” Carriage Bolt (#98), Ø ¾” Washer (#109), and M10 Aircraft Nut (#106).
D.) Attach the Power Station Vertical Frame (#7) to the Power Station Base Frame (#3). Secure
it with one M10 x 2 ½” Carriage Bolt (#98), Ø ¾” Washer (#109), and M10 Aircraft Nut
(#106).

DIAGRAM 4

10

STEP 5 (See Diagram 5)
A.) Do not tighten all Nuts and Bolts in this step until instructed to do so.
B.) Place the Upper Frame (#8) onto the Right Vertical Frame (#5) and two Guide Rods (#4).
Secure the Upper Frame to the Right Vertical Frame with two M10 x 2 ½” Carriage Bolts (#98),
one 4 3/8” x 1 ¾” Bracket (#84), two Ø ¾” Washers (#109), and two M10 Aircraft Nuts (#106).
C.) Secure the Upper Frame to the two Guide Rods with two M10 x 1” Allen Bolts (#94) and Ø ¾”
Washers (#109).
D.) Place the Top Socket Assembly (#9) onto the two Guide Rods on the rear. Secure them with
two M10 x 1” Allen Bolts (#94) and Ø ¾” Washers (#109).
E.) Connect the Top Socket Assembly (#9), Power Station Vertical Frame (#7), Upper Frame (#8)
and Left Vertical Frame (#6) together. Align the holes and secure them with two M10 x 2 ½”
Carriage Bolts (#98), Ø ¾” Washers (#109), and M10 Aircraft Nuts (#106).

11

STEP 6 (See Diagram 6)
A.) Securely tighten all Nuts and Bolts previously installed.
B.) Attach the Right Seat Support (#10) to the Right Base Frame (#1). Secure it with one
M10 x 2 ½” Carriage Bolt (#98), Ø ¾” Washer (#109), and M10 Aircraft Nut (#106).
C.) Attach the Right Seat Support (#10) to the Right Vertical Frame (#5). Secure it with
two M10 x 2 ½” Carriage Bolts (#98), one 4 3/8” x 1 ¾” Bracket (#84), two Ø ¾”
Washers (#109), and two M10 Aircraft Nuts (#106).
D.) Attach the Leg Developer (#26) to the bracket on the Right Seat Support. Secure it
with a M10 x 2 7/8” Allen Bolt (#92), two Ø ¾” Washers (#109), and one M10 Aircraft
Nut (#106). Do not over tighten the Nut and Bolt. Make sure the Leg Developer is able
to swivel.
E.) Attach the Butterfly Support Frame (#12) and the Butterfly Pulley Support (#46) to the
Right Vertical Frame. Align the holes and secure them together with two M10 x 2 ½”
Carriage Bolts (#98), Ø ¾” Washers (#109), and M10 Aircraft Nuts (#106).
F.) Attach two Swivel Pulley Brackets (#49) to the Butterfly Pulley Support (#46). Secure
each Bracket with one M12 x 4 3/8” Hex Bolt (#101), two Ø 1” Washers (#110), and
one M12 Aircraft Nut (#107). Do not over tighten the Nut and Bolt. Make sure each
Bracket is able to swivel.

12

DIAGRAM 6

13

STEP 7 (See Diagram 7)
A.) Attach the Left Seat Support (#11) to the Left Base Frame (#2). Secure it with one M10 x 2
½” Carriage Bolt (#98), Ø ¾” Washer (#109), and M10 Aircraft Nut (#106).
B.) Attach the Left Seat Support (#11) to the Left Vertical Frame (#6). Secure it with two M10 x 2
½” Carriage Bolts (#98), one 4 3/8” x 1 ¾” Bracket (#84), two Ø ¾” Washers (#109), and two
M10 Aircraft Nuts (#106).
C.) Attach the Leg Press Frame (#25) to the bracket on the Left Base Frame. Secure it with one
M12 x 3” Hex Bolt (#102), two Ø 1” Washers (#110), and one M12 Aircraft Nut (#107). DO
not over tighten the Nut and Bolt. Make sure the Leg Press Frame is able to swivel.
D.) Attach the Leg Press Plate (#52) to the Leg Press Adjustment Frame (#47). Secure it with
one M10 x 2 ½” Carriage Bolt (#98), Ø ¾” Washer (#109), and M10 Aircraft Nut (#106).
E.) Insert the Leg Press Adjustment Frame into the Leg Press Frame. Use a Lock Knob (#68) to
secure it in selected position.

DIAGRAM 7

14

STEP 8 (See Diagram 8)
A.) Attach the Chin-up Support (#17) to the Power Station Vertical Frame (#7). Secure it with
three M10x4” Allen Bolts (#100), six ؾ” Washers (#109) and three M10 Aircraft Nuts (#106).
B.) Attach the Chin-up Bar (#18) to the Chin-up Support. Secure it with two M10 x 4 1/8” Carriage
Bolts (#99), Ø ¾” Washers (#109), and M10 Aircraft Nuts (#106).
C.) Attach the Right & Left Dip Supports (#19 & #20) to the Power Station Vertical Frame (#7).
Securely tighten them together with two M10 x 2 ½” Carriage Bolts (#98), Ø ¾” Washers
(#109), and M10 Aircraft Nuts (#106). Insert the two Dip Handles (#21) into the Dip Supports.
Secure each Dip Handle with one M10 x 1” Allen Bolt (#94) and Ø ¾” Washer (#109).
D.) Attach the Foot Step (#28) to the Power Station Vertical Frame (#7). Secure it with one M10 x
2 ½” Carriage Bolt (#98), Ø ¾” Washer (#109), and M10 Aircraft Nut (#106).

15

STEP 9 (See Diagram 9)
A.) Insert the axle on the Right Butterfly (#15) through a Butterfly Adjustment Frame (#50) into
the Butterfly Support Frame (#12). Secure it with one M10 x 5/8” Allen Bolt (#93), Ø ¾”
Washer (#109), and Lock Ring (#33).
B.) Thread a T-shaped Pull Pin (#66) into the hole on the Right Butterfly from the bottom. Use
the Pin to adjust the Butterfly position.
C.) Repeat the same procedures A & B above to install the Left Butterfly (#14).
D.) Attach the Front Press Base (#29) to the Right Base Frame (#1). Secure it with one Axle
(#59), two Ø ¾” Washers (#109), and two M10 Aircraft Nuts (#106).
E.) Place the Front Press (#16) onto the Front Press Base. Secure it with four M10 x 2 ¾”
Carriage Bolts (#97), Ø ¾” Washers (#109), and M10 Aircraft Nuts (#106).

DIAGRAM 9

16

STEP 10 (See Diagram 10)
A.) Attach the Vertical Press Base (#23) to the pivot on the Power Station Vertical Frame (#7).
Secure it with one Axle (#59), two Ø ¾” Washers (#109), and two M10 Aircraft Nuts (#106).
B.) Attach one Vertical Press Arm (#24) to the Vertical Press Base. Secure it with two M10 x 2
½” Carriage Bolts (#98), Ø ¾” Washers (#109), and M10 Aircraft Nuts (#106).
C.) Repeat the same procedure to install the other Vertical Press Arm.

DIAGRAM 10

17

CABLE LOOP DIAGRAM

18

STEP 11 (See Cable Loop Diagram & Diagram 11)
A.) Attach the 102” Upper Cable (#36) to the front opening on the Upper Frame (#8).
Attach a Pulley (#64) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt
(#96), two Pulley Bushings (#63), and one M10 Aircraft Nut (#106). Draw the Cable
towards the back of the machine. Note: Make sure the Ball Stopper is underneath
the frame.
B.) Attach a Pulley to the opening on the Upper Frame. Secure it with one M10 x 2 3/8”
Allen Bolt (#96), two Pulley Bushings (#63), and one M10 Aircraft Nut (#106).
C.) Draw the Cable around the Pulley and downward. Install a Pulley to the two Double
Floating Pulley Brackets (#32). Secure it with one M10 x 1 ¾” Allen Bolt (#95), two
∅ ¾” Washers (#109), and one M10 Aircraft Nut (#106). Let the bracket hanging for
now. Draw the Cable around the Pulley then upward to the open bracket on the
Upper Frame.
D.) Install a Pulley to the bracket with a L-shaped Cable Retainer (#60).
E.) Draw the Cable around the Pulley then downward to the Selector Rod (#53). Attach
the ring on the Selector Pin (#62) to the Selector Rod (#53). Securely thread the
end of the Cable into the Selector Rod. Use the Nut at the end of the Cable to
tighten down the Bolt.

19

DIAGRAM 11

20

STEP 12 (See Cable Loop Diagram & Diagram 12)
A.) Clip one end of the 76” Butterfly Cable (#37) to the slot on the Left Butterfly Adjustment Frame
(#50). Draw the Cable through the slot then to the open Swivel Pulley Bracket (#49).
B.) Attach a Pulley (#64) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#95), two ∅ ¾”
Washers (#109), and one M10 Aircraft Nut (#106).
C.) Draw the Cable around the Pulley then downward. Install a Pulley to an Angled Floating Pulley
Bracket (#31). Let the Bracket hanging for now.
D.) Draw the Cable upward to the right Swivel Pulley Bracket on the opposite side. Install another
Pulley.
E.) Draw the Cable to the Right Butterfly Adjustment Frame and clip the end of the cable to the
slot.

DIAGRAM 12

21

STEP 13 (See Cable Loop Diagram & Diagram 13)
A.) Attach the 146” Lower Cable (#35) to the lower opening on the Leg Developer (#26).
Attach a Pulley (#64) to the opening. Secure it with one M10 x 2 3/8” Allen Bolt (#96), two
Pulley Bushings (#63), and one M10 Aircraft Nut (#106).
B.) Draw the Cable underneath the Pulley to the opening on the bottom of Right Seat Support
(#10). Attach a Pulley to the opening and secure it with one M10 x 2 3/8” Allen Bolt (#96),
two Pulley Bushings (#63), and one M10 Aircraft Nut (#106).
C.) Draw the Cable underneath the Pulley then through the bottom opening on the Right
Vertical Frame (#5) to the second open bracket on the Right Base Frame (#1).
D.) Attach a Pulley to the second open bracket. Secure it with one M10 x 1 ¾” Allen Bolt
(#95), two ∅ ¾” Washers (#109), and one M10 Aircraft Nut (#106).
E.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Bracket (#32)
previously installed in Step-11. Install a Pulley to the Brackets on selected hole. After
completing all the Cable installation, come back to this step and check the tension of the
Cable loop system. If the cables are too loose, move up the Pulley on the Bracket. Move
down the Pulley if the Cables are too tight.
F.) Draw the Cable around the Pulley then downward. Install a Pulley to an Angled Floating
Pulley Bracket (#31).
G.) Draw the Cable around the Pulley then upward to the Angled Floating Pulley Bracket (#31)
previously installed in Step-12. Secure the Cable to the Bracket with one M10 x 1” Allen
Bolt (#94), two Ø ¾” Washers (#109), and one M10 Aircraft Nut (#106).

22

DIAGRAM 13

23

STEP 14 (See Diagram 14)
A.) Attach the 49” Front Press Cable (#38) to the small opening on the Right Vertical Frame
(#5). Secure the head of the Cable to the small opening with one M10 x 2 3/8” Allen Bolt
(#96), two Ø3/4” Washers (#109), and one M10 Aircraft Nut (#106).
B.) Draw the Cable to the open bracket on the Front Press Base (#29). Install a Small Pulley
(#65) to the bracket.
C.) Draw the Cable around the Small Pulley then back to the opening on the Right Vertical
Frame (#5) then to the open bracket on the Right Base Frame (#1). Install a Pulley to
the bracket with a L-shaped Cable Retainer (#60).
D.) Draw the Cable around the Pulley then upward to the Angled Floating Pulley Bracket
(#31) previously installed in Step-13.
E.) Secure the end of Cable to the Bracket with one M10 x 1” Allen Bolt (#94), two Ø ¾”
Washers (#109), and one M10 Aircraft Nut (#106).

DIAGRAM 14

24

STEP 15 (See Diagram 15)
A.) Attach a Short Chain (#88) to the open bracket on the Power Station Vertical Frame
(#7). Secure it with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers (#109), and one
M10 Aircraft Nut (#106).
B.) Connect the 94” Vertical Press Cable (#39) to the Short Chain with a C-clip (#89).
C.) Install a Pulley to an Angled Floating Pulley Bracket (#31).
D.) Draw the Cable around the Pulley then upward to the first open bracket on the Top
Socket Assemble (#9).
E.) Install a Pulley to the bracket with a L-shaped Cable Retainer (#60). Draw the Cable
over the Pulley to the second open bracket. Repeat the same procedure to install
another Pulley.
F.) Draw the Cable around the Pulley then downward to the Selector Rod (#53). Attach
the ring on the Selector Pin (#62) to the Selector Rod. Securely thread the end of the
Cable into the Selector Rod. Use the Nut at end of the Cable to tighten down the Bolt.
G.) After completing the cable installations, come back to this step and adjust the length
of the Short Chain (#88). If the cables are too loose, shorten the Chain.

25

DIAGRAM 15

26

STEP 16 (See Diagram 16)
A.) Attach the 216” Leg Press Cable (#40) to the bracket on the back of Leg Press Frame (#25).
Secure it with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers (#109), and one M10 Aircraft
Nut (#106). Draw the Cable to the open bracket on the Left Seat Support (#11). Install a
Pulley to the bracket. Draw the Cable around the Pulley then back to the open bracket on the
Leg Press Frame. Install another Pulley.
B.) Draw the Cable around the Pulley then through the opening on the Left Seat Support (#11)
and Left Vertical Frame (#6) to the open bracket on the Left Base Frame (#2). Install a Pulley
to the bracket.
C.) Draw the Cable underneath the Pulley then upward to the open bracket on the Vertical Press
Base (#23). Install a Pulley.
D.) Draw the Cable around the Pulley then downward to the open bracket on the Power Station
Base Frame (#3). Install a Pulley to the bracket.
E.) Draw the Cable around the Pulley then upward to the Angled Floating Pulley Bracket installed
in Step-15. Secure it with one M10 x 1” Allen Bolt (#94), two Ø ¾” Washers (#109), and one
M10 Aircraft Nut (#106).

27

STEP 17 (See Diagram 17)
A.) Place a Seat Pad (#42) onto the Seat Incline Adjustment Frame (#27). Secure it with two M8 x
1 5/8” Allen Bolts (#104) and ∅ 5/8” Washers (#108). Insert the Frame into the opening on
the Left Seat Support (#11). Use a Lock Knob (#68) to secure the Seat at selected height.
B.) Insert two Foam Tubes (#13) halfway through the holes on the Right Seat Support (#10) and
the Leg Developer (#26). Push four Vinyl Foam Rolls (#58) onto the Tubes from both ends.
Plug four Foam Roll End Caps (#69) into the ends.
C.) Connect the Arm Curl Handle (#56) to the 146” Lower Cable (#35) with one Long Chain (#90)
and two C-clips (#89).
D.) Connect the Lat Bar (#48) to the 102” Upper Cable (#36) with one Short Chain (#88), and two
C-clips (#89).
E.) Cover the Weight Plates with four Weight Stack Covers (#30). Secure each Weight Stack
Cover with two M10 x 5/8” Allen Bolts (#93) and Ø ¾” Washers (#109).

28

STEP 18 (See Diagram 18)
A.) Attach the Backrest Board (#41) to the Right & Left Vertical Frames (#5 & #6). Secure each
Board with two M8 x 2 ½” Allen Bolts (#103) and Ø 5/8” Washers (#108).
B.) Attach the Power Station Backrest Board (#44) to the Power Station Vertical Frame (#7).
Secure it with two M8 x 2 ½” Allen Bolts (#103) and Ø 5/8” Washers (#108).
C.) Place the Seat (#42) onto the Right Seat Support (#10). Secure it with two M8 x 2 ½” Allen
Bolts (#103) and Ø 5/8” Washers (#108).
D.) Attach four Arm Pads (#43) to the Right and Left Butterfly (#15 & #14) and Dip Supports (#19
& #20). Secure each Arm Pad with two M8 x 2 ½” Allen Bolts (#103) and Ø 5/8” Washers
(#108).
E.) To maximize the performance of the gym, it is recommended to use light lubricant such as
WD-40 on the four chrome Guide Rods, which the weight plates slide up and down on, to
minimize friction.

DIAGRAM 18

29

PARTS LIST
KEY NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58

DESCRIPTION

Right Base Frame
Left Base Frame
Power Station Base Frame
Guide Rod
Right Vertical Frame
Left Vertical Frame
Power Station Vertical Frame
Upper Frame
Top Socket Assembly
Right Seat Support
Left Seat Support
Butterfly Support Frame
Foam Tube
Left Butterfly
Right Butterfly
Front Press
Chin-up Support
Chin-up Bar
Right Dip Support
Left Dip Support
Dip Handle
Ø 2” Sleeve
Vertical Press Base
Vertical Press Arm
Leg Press Frame
Leg Developer
Seat Incline Adjustment Frame
Foot Step
Front Press Base
Weight Stack Cover
Angled Floating Pulley Bracket
Double Floating Pulley Bracket
Lock Ring
Ø 1 ¾” Rubber Bumper
146” Lower Cable
102” Upper Cable
76” Butterfly Cable
49” Front Press Cable
94” Vertical Press Cable
216” Leg Press Cable
Backrest Board
Seat
Arm Pad
Power Station Backrest Board
Left Seat Support End Cap
Butterfly Pulley Support
Leg Press Adjustment Frame
Lat Bar
Swivel Pulley Bracket
Butterfly Adjustment Frame
Ø1 ½” x 7/8” Bushing
Leg Press Plate
Selector Rod
Weight Plate
Selector Stem
Arm Curl Handle
Arm Curl Handle Bar
Vinyl Foam Roll

Q’ty
1
1
1
4
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
2
1
1
1
1
1
4
3
2
2
2
1
1
1
1
1
1
2
2
4
1
1
1
1
1
2
2
8
1
2
28
2
1
1
4

59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112

30

Axle
L-shaped Cable Retainer
2” Square End Cap
Weight Selector Pin
Pulley Bushing
Pulley
Small Pulley
T-shaped Pull Pin Set
2” x 1 ¾” Sleeve
Lock Knob
Foam Roll End Cap
2” x 1” End Cap
1” Square End Cap
¾” x 1 5/8” End Cap
1 ½” Square End Cap
1 ¾” Square End Cap
Ø 2” Cone-shaped End Cap
6” Handle Grip
17” Vertical Press Handle Grip
5 ¼” Handle Grip
12 ¾” Chin-up Handle Grip
Ø 1 ½” x 1” Bushing
Ø 1” x Ø ½” Bushing
Ø 1” x Ø 7/8” Bushing
Ø ¾” x Ø 3/8” Bushing
4 3/8” x 1 ¾” Bracket
Ø 1 7/8” x 1 5/8” Rubber Bumper
Ø 2 ½” x 1” Rubber Bumper
Ø 1 ½” x 5/8” Rubber Bumper
Short Chain
C-clip
Long Chain
Ø 1” Cone-shaped End Cap
M10 x 2 7/8” Allen Bolt
M10 x 5/8” Allen Bolt
M10 x 1” Allen Bolt
M10 x 1 ¾” Allen Bolt
M10 x 2 3/8” Allen Bolt
M10 x 2 ¾” Carriage Bolt
M10 x 2 ½” Carriage Bolt
M10 x 4 1/8” Carriage Bolt
M10 x 4” Allen Bolt
M12 x 4 3/8” Hex Bolt
M12 x 3” Hex Bolt
M8 x 2 ½” Allen Bolt
M8 x 1 5/8” Allen Bolt
M6 x 5/8” Philips Screw
M10 Aircraft Nut
M12 Aircraft Nut
Ø 5/8” Washer
Ø ¾” Washer
Ø 1” Washer
Ankle Strap
Single Handle
#6 Allen Wrench (Tool)
#5 Allen Wrench (Tool)
26

2
4
1
2
8
21
1
2
2
2
4
2
2
4
3
17
8
10
2
2
2
2
2
12
2
3
1
4
1
2
5
1
2
1
10
15
18
5
4
26
2
3
2
1
16
2
2
68
3
18
107
6
1
1
1
1

TSA-9900 WEIGHT RESISTANCE CHART
WEIGHT PLATE
Station

1

2

3

4

5

6

7

Low Pulley

35

45

55

65

75

85

95

Lat Pull

15

25

35

45

55

65

75

Butterfly

10

17

24

31

38

45

52

Leg Press

30

50

70

90

110

130

150

Front Press

35

50

65

80

95

110

125

Vertical Press

30

43

56

69

82

95

108

WEIGHT PLATE
Station

8

9

10

11

12

13

14

Low Pulley

105

115

125

135

145

155

165

Lat Pull

85

95

105

115

125

135

145

Butterfly

73

80

87

94

101

108

115

Leg Press

170

190

210

230

250

270

290

Front Press

140

155

170

185

200

215

230

Vertical Press

121

134

147

160

173

186

200

*Numbers are approximate. Actual weight may vary.
*Value for butterfly is for each arm.

31

IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.

www.impex-fitness.com
info@impex-fitness.com
When ordering replacement parts, always give the following information.
1.
2.
3.
4.

Model
Description of Parts
Part Number
Date of Purchase

32



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Producer                        : Acrobat Distiller 4.05 for Windows
Creator                         : Microsoft Word 9.0
Modify Date                     : 2005:09:16 12:26:39-07:00
Author                          : ¶À¶i§Q
Title                           : PARTS LIST
Create Date                     : 2005:09:16 12:25:30
Page Count                      : 33
Page Mode                       : UseNone

EXIF Metadata provided by EXIF.tools