Impex CR 5 PARTS LIST User Manual To The 71cd49e0 74e0 4796 Aecf E19eb864c7f3
User Manual: Impex CR 5 to the manual
Open the PDF directly: View PDF 
.
Page Count: 26
| Download | |
| Open PDF In Browser | View PDF |
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Hardware Identifier
MARCY CORNER GYM
CR 5
Assembly Instruction
Parts List
Resistance Chart
Warranty
Ordering Parts
Model
MWB CR 5
Retain This
Manual for
Reference
9-20-02
OWNER'S
MANUAL
IMPEX FITNESS PRODUCTS
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@impex-fitness.com
TABLE OF CONTENTS
BEFORE YOU BEGIN...................................................................................... 1
IMPORTANT SAFETY NOTICES..................................................................... 2
HARDWARE IDENTIFIER.....…....................................................................... 3
ASSEMBLY INSTRUCTIONS...............................................................…..........4
PARTS LIST…………………………………………………………….……….…….23
RESISTANCE CHART………………………………………………………………. 24
WARRANTY.................................................................................................… 25
ORDERING PARTS......................................................................................... 25
BEFORE YOU BEGIN
Thank you for selecting the MARCY CR5 CORNER GYM by IMPEX FITNESS
PRODUCTS. For your safety and benefit, read this manual carefully before
using the machine. As a manufacturer, we are committed to provide you
complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, we guarantee you complete satisfaction through
direct assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
info@impex-fitness.com
1
IMPORTANT SAFETY NOTICE
PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply whenever
you operate a piece of exercise equipment. Be sure to read the entire manual before you
assemble or operate your machine. In particular, note the following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN.
THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS
WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING
ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS
PRODUCT.
SAVE THESE INSTRUCTIONS.
2
3
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended two or people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Place the Right Base Frame (#46) and Left Base Frame (#87) on the floor, at a right angle to
each other. Attach the Rear Vertical Beam (#50) to the joint and align the holes. Secure the
holes with two M10 x 3” Carriage Bolts (#64), ∅ 3/4” Washers (#6) and M10 Aircraft Nuts (#5).
DO NOT tighten all the nuts and bolts yet.
Diagram 1
4
STEP 2
(See Diagram 2)
A.) Attach the Right Vertical Beam (#21) to the Right Base Frame (#46). Secure it with two M10 x
2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
B.) Attach the Right Seat Support (#49) to the Right Vertical Beam (#21). Secure it with one
Bracket (#7), two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts
(#5).
C.) Attach the other end of Right Seat Support (#49) to the Right Base Frame (#46). Secure it with
one M10 x 2 ¾” Carriage Bolt (#17), ∅ ¾” Washer (#6), and M10 Aircraft Nut (#5).
D.) Attach the Leg Developer (#40) to the front open bracket on the Right Seat Support. Secure it
with a Leg Developer Axle (#41), two ∅ ¾” Washers (#6), and M10 x ¾” Allen Bolts (#37).
DIAGRAM 2
5
STEP 3
(See Diagram 3)
A.) Slide two ∅ 2 ½” Rubber Bumpers (#58) onto two Chromed Guide Rods (#58). Insert the two
Guide Rods into the holes on the Right Base Frame (#46). Slide the Selector Stem (#67) onto
the two Guide Rods (#22). Slide the Selector Stem over the Selector Rod (#69). Secure the
Selector Rod to the Selector Stem with two M10 x 1” Allen Bolts (#56). DO NOT install the
plates yet.
B.) Repeat the Procedure A above to install another set of Guide Rods.
C.) Place the Upper Frame (#8) over the two sets of Guide Rods then onto top of Right Vertical
Beam (#21) and Rear Vertical Beam (#50).
D.) Secure each set of Guide Rods (#22) to the Upper Frame with two M10 x 1” Allen Bolts (#56)
and ∅ ¾” Washers (#6).
E.) Secure the Right Vertical Beam (#21) to the Upper Frame with one Bracket (#7), two M10 x 2
¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
F.) Attach top of Left Vertical Beam (#77) to the Upper Frame. Attach the bottom of Left Vertical
Beam to the Left Base Frame (#87). Secure the bottom of Left Vertical Beam with two M10 x 2
¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
G.) Secure the Left Vertical Beam (#77), Rear Vertical Beam (#50), and Upper Frame (#8) all
together with two M10 x 3” Carriage Bolts (#64), ∅ ¾” Washers (#6), and M10 Aircraft Nuts
(#5).
H.) Attach the Left Seat Support (#92) to the Left Vertical Beam (#77). Secure it with one Bracket
(#7), two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
Attach the other end of Left Seat Support (#92) to the Left Base Frame (#87). Secure it with
one M10 x 2 ¾” Carriage Bolt (#17), ∅ ¾” Washer (#6), and M10 Aircraft Nut (#5).
I.) Securely tighten all nuts and bolts previously installed.
J.) Carefully tilt the machine on its side. (Help of another person is a MUST.) Secure the four
Guide Rods (#22) to the Right Base Frame (#46) with four M10 x 1” Allen Bolts (#56).
K.) Attach the bottom of Leg Press Frame (#84) to the bracket on the Left Base Frame (#87).
Secure it with a M12 x 3” Allen Bolt (#89), two ∅ 7/8” Washers (#71), and one M12 Aircraft Nut
(#57).
L.) Attach a Leg Press Diagonal Support (#90) to each side of the Leg Press Frame. Secure them
together with two M10 x 2 ½” Carriage Bolts (#100), ∅ ¾” Washers (#6), and M10 Aircraft Nuts
(#5).
6
DIAGRAM 3
7
STEP 4 (See Diagram 4)
A.) Attach the Front Press Base (#97) to the Right Base Frame (#46). Secure it with a 9 ¼” Front
Press Axle (#60), two ∅ ¾” Washers (#6), and two M10 Aircraft Nuts (#5).
B.) Attach the Front Press Frames (#63) to the Front Press Base. Secure it with four M10 x 2 ¾”
Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts (#5).
DIAGRAM 4
8
STEP 5 (See Diagram 5)
A.) Attach the Butterfly Support Frame (#18) to the front of Right Vertical Beam (#21). Attach the
Butter Pulley Support (#74) to the back of Right Vertical Beam. Align the holes. Secure them
together with two M10 x 2 ¾” Carriage Bolts (#17), ∅ ¾” Washers (#6), and M10 Aircraft Nuts
(#5).
B.) Insert the Axle on the Left Butterfly (#20) into the hole on the Butterfly Support Frame from the
bottom. Secure it with one ∅ 1 ½” Washer (#16), ∅1 3/8” Lock Ring (#13), M6 x 1 5/8” Hex
Bolt (#12), and M6 Aircraft Nut (#14). Repeat the same procedure to install the other side.
C.) Slide two Butterfly Foam Rolls (#27) onto the Butterfly Arms.
D.) Attach a Swivel Pulley Bracket (#72) to the bottom of the Butterfly Pulley Support (#74).
Secure it with a M12 x 4 ½” Allen Bolt (#70), two 7/8” Washers (#71), and one M12 Aircraft Nut
(#57). Repeat for the other side.
DIAGRAM 5
9
STEP 6 (See Diagram 6)
A.) Attach the Vertical Press Frame (#78) to the Rear Vertical Beam (#50). Secure it with a M10 x
4 7/8” Vertical Press Axle (#81), two ∅ ¾” Washers (#6), and two M10 x 1” Allen Bolts (#56).
B.) Place the Vertical Press Frame rest onto the ∅ 1 ½” Rubber Bumper (#83).
DIAGRAM 6
10
CABLE LOOP DIAGRAM
11
STEP 7 (Upper Cable Loop & Diagram 7)
A.) Attach the 108” Upper Cable (#93) to the front opening on the Upper Frame (#8). Attach a
Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley
Bushings (#11), and one M10 Aircraft Nut (#5). Draw the Cable towards the back of the
machine. Note: Make sure the Ball Stopper is underneath the frame.
B.) Attach a Pulley to the bracket on the Upper Frame. Secure it with one M10 x 2” Allen Bolt
(#98), two ∅ ¾” Washers (#6), one L-shaped Pulley Bracket (#86), and one M10 Aircraft Nut
(#5).
C.) Pull the Cable downward. Install a Pulley with a Flat Double Floating Pulley Bracket (#59). Let
the bracket hanging for now.
D.) Draw the Cable around the Pulley then upward to the second open bracket on the Upper
Frame. Install another Pulley with a U-shaped Pulley Bracket (#85).
E.) Draw the Cable around the Pulley then downward to the Selector Rod (#69). Securely thread
the end of the Cable into the Selector Rod (#69).
UPPER CABLE LOOP DIAGRAM
12
DIAGRAM 7
13
STEP 8 (See Butterfly Cable Loop & Diagram 8)
A.) Attach the 83” Butterfly Cable (#95) to the slot on the back of Left Butterfly (#20). Draw the
Cable through the slot then to the open left Swivel Pulley Bracket (#72).
B.) Attach a Pulley (#79) to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾”
Washers (#6), and one M10 Aircraft Nut (#5).
C.) Draw the Cable around the Pulley then downward. Install a Pulley to the Angled Double
Floating Bracket (#51). Let the Bracket hanging for now.
D.) Draw the Cable upward to the right Swivel Pulley Bracket. Install another Pulley..
E.) Draw the Cable to the Right Butterfly (#26) and secure the cable end to the slot.
BUTTERFLY CABLE LOOP DIAGRAM
14
DIAGRAM 8
15
STEP 9 (See Front Press Cable Loop & Diagram 9)
A.) Attach the 247” Front Press Cable (#94) to the lower opening on the Leg Developer (#40).
B.) Attach a Pulley (#79) to the opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two
Pulley Bushings (#11), and one M10 Aircraft Nut (#5).
C.) Draw the Cable underneath the Pulley through the opening on the Right Seat Support (#49) to
the open bracket on the Right Base Frame (#46).
D.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾” Washers
(#6), and one M10 Aircraft Nut (#5).
E.) Continue drawing the Cable along the Right Base Frame to another open bracket. Install a
Pulley as described in Step D above with a L-shaped Pulley Bracket (#86). Draw the Cable
around the Pulley then back to the opening between the Front Press Base (#97).
F.) Attach a Pulley to the opening. Secure it with one M10 x 8 ¼” Allen Bolt (#62), two ∅ ¾”
Washers (#6), and one M10 Aircraft Nut (#5).
G.) Draw the Cable around the Pulley then back to the lower opening on the Right Vertical Beam
(#21). Install another Pulley as described in Step D above. Draw the Cable back to the open
bracket on the back of Front Press Base.
H.) Install another Pulley as described in Step D above. Draw the Cable back through the lower
opening on the Right Vertical Beam (#21) to the open bracket on the back of the Beam. Install
another Pulley.
I.) Draw the Cable upward to the hanging Angled Double Floating Bracket (#51) previously
installed in STEP 8. Install another Pulley. Draw the Cable downward to the open bracket on
the Right Base Frame (#46). Install another Pulley with a U-shaped Pulley Bracket (#85).
J.) Draw the Cable upward to the hanging Flat Double Floating Pulley Bracket (#59) previously
installed in STEP 7. Install another Pulley.
K.) Draw the Cable around the Pulley then downward and connect to the Right Base Frame with a
Chain (#3) and two C-clips (#4). Adjust the tension of the Cable by adjusting the length of the
Chain.
FRONT PRESS CABLE LOOP DIAGRAM
16
DIAGRAM 9
17
STEP 10 (See Leg Press Cable Loop & Diagram 10)
A.) Attach one end of the 82” Leg Press Cable (#96) to the open slot on the back of the Leg
Press Frame (#84). Secure it with one M10 x 2 ½” Allen Bolt (#10), two ∅ ¾” Washers (#6),
and one M10 Aircraft Nut (#5).
B.) Draw the Cable to the front opening on the Left Seat Support (#92). Attach a Pulley to the
opening. Secure it with one M10 x 2 ½” Allen Bolt (#10), two Pulley Bushings (#11), and one
M10 Aircraft Nut (#6).
C.) Draw the Cable around the Pulley then back to the lower opening on the Leg Press Frame.
Install a Pulley as described in Step B above.
D.) Draw the Cable around the Pulley then towards back of the machine through the hole on the
bottom of the Left Vertical Beam (#77) to the open bracket on the Left Base Frame (#87).
E.) Attach a Pulley to the bracket. Secure it with one M10 x 2” Allen Bolt (#98), two ∅ ¾”
Washers (#6), one L-shaped Pulley Bracket (#86), and one M10 Aircraft Nut (#5).
F.) Pull the Cable upward and connect to the 298” Vertical Press Cable (#102) with two C-clips
(#4) and one Chain (#3). After completing the steps, adjust the length of this Chain to adjust
the tightness of the Cables.
G.) Draw the Vertical Press Cable to the opening between the Vertical Press Frame (#78). Attach
a Pulley to the opening. Secure it with one M10 x 5 ¾” Allen Bolt (#82), two ∅ ¾” Washers
(#6), and one M10 Aircraft Nut (#5).
H.) Draw the Cable around the Pulley and downward to the middle open bracket on the Left Base
Frame. Install a Pulley with a U-shaped Pulley Bracket (#85).
I.) Pull the Cable upward back to the opening on the Vertical Press Frame. Install another Pulley
as described in Step G above.
J.) Draw the Cable downward to the last open bracket on the rear of the Left Base Frame. Install
a Pulley with a U-shaped Pulley Bracket (#85).
K.) Draw the Cable upward to the last open bracket on the Upper Frame (#8). Install another
Pulley. Draw the Cable downward and securely threaded it into the Selector Rod.
LEG PRESS CABLE LOOP DIAGRAM
18
DIAGRAM 10
19
STEP 11 (See Diagram 11)
A.) Place a Seat Pad (#29) onto the Left Seat Support (#92). Secure it with two M8 x 2 1/8” Allen
Bolts (#25) and ∅ 5/8” Washers (#24).
B.) Attach a Backrest Board (#28) to the Left Vertical Beam (#77). Secure it with two M8 x 2 1/8”
Allen Bolts (#25) and ∅ 5/8” Washers (#24).
C.) Attach the Leg Press Plate (#76) onto the Leg Press Frame (#84). Secure it with a L-shaped
Pin (#75).
DIAGRAM 11
20
STEP 12 (See Diagram 12)
A.) Place a Seat Pad (#29) onto the Right Seat Support (#49). Secure it with two M8 x 2 1/8”
Allen Bolts (#25) and ∅ 5/8” Washers (#24).
B.) Attach a Backrest Board (#28) to the Right Vertical Beam (#21). Secure it with two M8 x 2 1/8”
Allen Bolts (#25) and ∅ 5/8” Washers (#24).
C.) Insert two Foam Roll Tubes (#36) halfway through the holes on the Right Seat Support (#49)
and Leg Developer (#40). Push four Foam Rolls (#33) onto the Tubes from both sides. Plug
four ∅ 1” Round End Caps (#32) into the ends.
D.) Attach the Arm Curl Pad (#34) to the Arm Curl Stand (#35). Secure it with two M8 x 5/8” Allen
Bolts (#31) and ∅ 5/8” Washers (#24). Insert the Arm Curl Stand into the opening in front of
the seat. Use the Lock Knob (#47) on the Right Seat Support to obtain the desired position.
E.) Connect the Lat Bar (#2) to the Upper Cable with a C-clip (#4) and a Chain (#3).
F.) Connect the Arm Curl Handle (#44) to the Front Press Cable (#94) with a C-clip (#4) and a
Chain (#3).
DIAGRAM 12
21
STEP 13 (See Diagram 13)
A.) Securely tighten all the nuts and bolts previously installed.
B.) Before putting the Weight Plates on, now move the machine to the corner of the room or
place where you will use the machine.
C.) Lift up the Selector Rod and install one stack of 19 Weight Plates (#66). To install the plates,
hold the plate at an angle and place between the two Guide Rods then drop it down. Make
sure the grooves on the plastic covers all face up. All the Plates should interlock with each
other. See diagram below. It is strongly recommended to spray some lubricant such as WD40 on the two Guide Rods to minimize friction. Use the Selector Pin (#55) to select the desired
weights. The Magnet on the Pin should face up. Repeat the same procedure to install
another stack of Weight Plates.
D.) Attach four Weight Stack Covers (#23) to the machine and secure each Weight Stack Cover
with two M10 x 1” Allen Bolts (#56) and ∅ 3/4” Washers (#6).
DIAGRAM 13
22
PARTS LIST
KEY NO.
DESCRIPTION
Q’ty
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Lat Bar Grip
Lat Bar
Chain
C-clip
M10 Aircraft Nut
∅ ¾” Washer
Bracket
Upper Frame
1 ¾” Square End Cap
M10 x 2 ½” Allen Bolt
Pulley Bushing
M6 x 1 5/8” Hex Bolt
∅1 3/8” Lock Ring
M6 Aircraft Nut
Butterfly Axle Sleeve
∅ 1 ½” Washer
M10 x 2 ¾” Carriage Bolt
Butterfly Support Frame
2” Square End Cap
Left Butterfly
Right Vertical Beam
Guide Rod
Weight Stack Cover
∅ 5/8” Washer
M8 x 2 1/8” Allen Bolt
Right Butterfly
Butterfly Foam Roll
Backrest Board
Seat Pad
2” Sleeve
M8 x 5/8” Allen Bolt
∅ 1” Round End Cap
Foam Roll
Arm Curl Pad
Arm Curl Stand
Foam Roll Tube
M10 x ¾” Allen Bolt
∅ 1 5/8” Rubber Bumper
M6 x 5/8” Philips Screw
Leg Developer
Leg Developer Axle
Arm Curl Handle
Arm Handle Sleeve
Arm Curl Handle tube
Handle Grip
Right Base Frame
Lock Knob
1” Square End Cap
Right Seat Support
Rear Vertical Beam
2
1
4
6
52
82
3
1
17
8
10
2
2
2
2
2
16
1
2
1
1
4
4
11
8
1
2
2
2
1
2
4
4
1
1
2
2
2
2
1
1
1
2
1
4
1
1
4
1
1
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
23
Angled Double Floating Bracket
M5 Screw
Magnet Box
Magnet
Selector Pin
M10 x 1” Allen Bolt
M12 Aircraft Nut
∅ 2 ½” Rubber Bumper
Flat Double Floating Pulley Bracket
9 ¼” Front Press Axle
∅ 7/8” Metal Bushing
M10 x 8 ¼” Allen Bolt
Front Press Frame
M10 x 3” Carriage Bolt
Weight Plate Cover
Weight Plate
Selector Stem
Selector Stem Bushing
Selector Rod
M12 x 4 ½” Allen Bolt
∅7/8” Washer
Swivel Pulley Bracket
1 ½” Square End Cap
Butterfly Pulley Support
L-shaped Pin
Leg Press Plate
Left Vertical Beam
Vertical Press Frame
Pulley
2” x 1” End Cap
M10 x 4 7/8” Vertical Press Axle
M10 x 5 ¾” Allen Bolt
∅ 1 ½” Rubber Bumper
Leg Press Frame
U-shaped Pulley Bracket
L-shaped Pulley Bracket
Left Base Frame
∅ 7/8” x ∅ 5/8” Leg Press Bushing
M12 x 3” Allen Bolt
Leg Press Diagonal Support
Vertical Press Grip
Left Seat Support
108” Upper Cable
247” Front Press Cable
83” Butterfly Cable
82” Leg Press Cable
Front Press Base
M10 x 2” Allen Bolt
M6 x 5/8” Philips Screw
M10 x 2 ½” Carriage Bolt
Ankle Strap
298” Vertical Press Cable
1
2
2
2
2
22
3
4
1
1
14
1
2
4
76
38
2
4
2
2
6
2
3
1
1
1
1
1
25
2
1
2
1
1
7
2
1
2
1
2
2
1
1
1
1
1
1
17
1
2
1
1
WEIGHT RESISTANCE CHART
WEIGHT PLATE
Station
1
2
3
4
5
6
7
8
9
Low Pulley
40
54
68
80
93
105
116
127
138
Lat Pull
40
55
70
80
90
100
110
120
130
Butterfly
50
55
60
67
74
80
93
106
120
Leg Press
80
107
135
160
185
210
232
254
275
Front Press
54
80
107
116
125
135
162
189
215
Vertical Press
45
60
76
92
113
129
146
172
198
WEIGHT PLATE
Station
10
11
12
13
14
15
16
17
18
19
Low Pulley
150 162 174 186 198 210 222 234 246 258
Lat Pull
140 150 160 170 180 190 200 210 220 230
Butterfly
133 146 159 172 185 198 211 224 237 250
Leg Press
297 319 341 363 385 407 429 451 473 495
Front Press
241 267 293 319 345 371 397 423 449 475
Vertical Press 218 238 258 278 298 318 338 358 378 398
*Numbers are approximate. Actual weight may vary.
*Value
*Value for butterfly is for each arm.
24
IMPEX INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of two years on the Frame from the date of
purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this
Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling
IMPEX Customer Service Department at 1-800-999-8899. All freights on products returned to
IMPEX must be prepaid by the customer. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or
abnormal usage or repairs not provided by an IMPEX authorized service center or for products
used for commercial or rental purposes. No other warranty beyond that specifically set forth
above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or
in connection with the use or performance of the product or other damages with respect to any
economic loss, loss of property, loss of revenues or profits, loss of enjoyments or use, costs of
removal, installation or other consequential damages or whatsoever natures. Some states do not
allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above
limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied
warranties of merchantability or fitness for a particular purpose is limited in its scope and duration
to the terms set forth herein. Some states do not allow limitations on how long an implied
warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state
to state.
IMPEX INC.
14777 Don Julian
City of Industry, CA 91746
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800999-8899 during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific
standard time.
www.impex-fitness.com
info@impex-fitness.com
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
25
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Producer : Acrobat Distiller 4.05 for Windows Creator : Microsoft Word 9.0 Modify Date : 2002:10:17 10:02:49-07:00 Author : ¶À¶i§Q Title : PARTS LIST Create Date : 2002:10:17 10:02:14 Page Count : 26 Page Mode : UseNoneEXIF Metadata provided by EXIF.tools