InBody INBT-USB Bluetooth Dongle User Manual

InBody Co., Ltd. Bluetooth Dongle

User Manual

 InBT-USB Bluetooth Dongle with USB interface                   Note; * This user manual describes methods and functions for using InBT-USB. * This product is a USB-type Bluetooth dongle which shall be assembled into the InBody (Body  composition  analyzer)  manufactured  by  Biospace  for  supporting  data communications via the USB port.
1. Overview This product is a USB-type Bluetooth dongle which shall be assembled into the USB port of the  InBody  (Body  composition  analyzer)  for  supporting  data  communications  between  the InBody and a personal computer, or external device has Bluetooth function.    (1) Contents  ①  InBT-USB ②  User’s Manual  2. Product Specifications  USB 2.0 Full Speed support Bluetooth Version 2.1 + EDR, Class 1 Internal antenna Frequency band  2.4GHz ISM band Operation range  200-400m Transmission strength  +13 dBm Reception sensitivity  -86 dBm Supported services  Serial Port Protocol(SPP), Dial-up Networking Profile(DUN), OBEX Objext Push, Profile(OPP), OBEX File Transfer Profile(FTP),  Human  Interface  Device  Profile(HID),  Phone  Book  Access Profile(PBAP), Health Device Profile(HDP), Device   Identification Profile(DI), Service Discovery Protocol(SDP)      Bluetooth 2.1 supports AFH (Adaptive Frequency Hopping). AFH helps minimize interference between WiFi and Bluetooth signals by automatically selecting communication channels that are not used by  WiFi  signals. Please  keep in mind that  AFH  may not guarantee  complete non-interference  between  WiFi  and  Bluetooth  signals  depending  on  the  operating environment. This includes the number of devices used and the distances between them. Performance may vary by operating environment.
 3. Usage of USB Type Bluetooth Dongle ※  The Bluetooth dongle, InBT-USB shall be assembled inside of the InBody (Body composition analyzer)  as  following  picture  by  the  Biospace  and  measured  data  will  be  transferred  to  a personal computer, or external device has Bluetooth function.                      InBT-USB
   1) Driver Support Please install driver below in your OS imbedded board.   The drivers listed below can be downloaded for free from the FTDI website (www.ftdichip.com). For more information on driver installation, visit the following site: http://www.ftdichip.com/Documents/InstallGuides.htm.  (1) Virtual COM Port (VCP) Drivers   You can use ASCII commands on a terminal program to perform various controls and configuration settings for InBT-USB.            Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008         Windows 7 32,64-bit       Windows XP and XP 64-bit         Windows Vista and Vista 64-bit       Windows XP Embedded  Windows CE 4.2, 5.0 and 6.0       Mac OS 8/9, OS-X         Linux 2.4 and greater    (2) D2XX Direct Drivers (USB Drivers + DLL S/W Interface)   You should make your program for control of InBT-USB.          Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008         Windows 7 32,64-bit       Windows XP and XP 64-bit         Windows Vista and Vista 64-bit       Windows XP Embedded         Windows CE 4.2, 5.0 and 6.0          Linux 2.4 and greater
 2) Program Settings for OS imbedded board  After installing the InBT-USB driver on a VCP (virtual COM port), you can use ASCII commands on a terminal program to perform various controls and configuration settings for InBT-USB.    A terminal program is used for controlling or setting serial ports. The terminal program described in this manual is HyperTerminal provided with MS Windows. For more information on HyperTerminal, see the MS Windows Help.                                       Figure 1. HyperTerminal communication port settings screen  (1) The following default settings are used for communication between InBT-USB and HyperTerminal. • Baud rate: 115200bps • Data bits: 8 • Parity bit: No parity • Stop bits: 1 • HW Flow Control: Disable    (2) ASCII commands Please control the InBT-USB using the ASCII commands below.  Provided below are instructions for using basic ASCII commands. For more information on the examples and instructions for using other commands, contact Biospace.
  - AT command  This command is used for testing operation of the InBT-USB firmware. The command returns OK to indicate normal operation.       - SET command This command is used for retrieving or modifying the InBT-USB settings. . Retrieving settings                            AT OK SET SET BT BDADDR 00:07:80:ff:ff:f1 SET BT NAME WT32-A SET BT CLASS 001f00 SET BT IDENT BT:47 f000 4.0.0 Bluegiga iWRAP SET BT LAP 9e8b33 SET BT PAGEMODE 4 2000 1 SET BT POWER 0 0 0 SET BT ROLE 0 f 7d00 SET BT SNIFF 0 20 1 8 SET BT MTU 667 SET CONTROL BAUD 115200,8n1 SET CONTROL CD 00 0 SET CONTROL ECHO 7 SET CONTROL ESCAPE 43 00 1 SET CONTROL GAIN 8 8 SET CONTROL MSC DTE 00 00 00 00 00 00 SET CONTROL READY 00 SET PROFILE SPP Bluetooth Serial Port SET
  . Modifying settings   In the following example, the Bluetooth PIN code required for pairing is set to  ¡°0000.¡±  The   code is saved in the non-volatile memory and only needs to be set once.     - INQUIRY command This command is used for searching for other Bluetooth devices available for pairing within the operating range.                 - CALL command The CALL command is used for establishing Bluetooth connections. The CALL event indicates that a connection is being attempted the CONNECT event indicates that a connection has been established.          - SET RESET command     This command is used for resetting the InBT-USB settings to factory defaults.       INQUIRY 5 INQUIRY_PARTIAL 00:21:86:35:c9:c8 02010c INQUIRY_PARTIAL 00:07:80:93:d7:66 240408 INQUIRY_PARTIAL a8:7b:39:c3:ca:99 5a020c INQUIRY 3 INQUIRY 00:21:86:35:c9:c8 02010c INQUIRY 00:07:80:93:d7:66 240408 INQUIRY a8:7b:39:c3:ca:99 5a020c CALL 00:07:80:93:d7:66 1101 RFCOMM CALL 0 CONNECT 0 RFCOMM 1 SET RESET WRAP THOR AI (4.0.0 build 317) Copyright (c) 2003-2010 Bluegiga Technologies Inc. READY. SET BT AUTH * 0000
 5. Troubleshooting  (1) If connection is not good, try pairing the devices again. (2) Transferring data in large volumes may result in low performance depending on the device connected.   (3) This product uses same frequency bands as normal WiFi signals and is subject to ambient interferences.    FCC Information   This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions :   (1) This Device may not cause harmful interface, and    (2) This device must accept any interference received, including interference that may   cause undesired operation.    Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant  to Part  15  of FCC  Rules. These  limits  are designed to  provide reasonable  protection  against harmful  interference  when  the  equipment is operated in a commercial  environment  This  equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the  instructions,  may  cause  harmful  interference  to  radio  communications.  However,  there  is  no guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause harmful interference to radio or television reception, which can be determined by turning the equipment off  and  on,  the  user  is  encouraged  to  try  correct  the  interference  by  one  or  more  of  the  following measures:   1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help.   WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
    ¨Ï 1996-2012 Biospace Co., Ltd. All rights reserved. Notice This user’s manual cannot be copied, translated or transformed into  different  media  without  a  prior written consent from Biospace Co., Ltd, according to the copyright laws. This user’s manual and product pertinent to this manual may have misprints or technical flaws, which can be modified without prior notice  to  the  readers.  Biospace  is  not  liable  for  any  damage  caused by a failure to meet the requirements in this user’s manual. Biospace Co., Ltd. [Head office] 518-10 Dogok 2- dong, Gangnam-gu, Seoul 135-854 KOREA   TEL : 82-2-501-3939  FAX : 82-2-501-3978 Homepage : http://www.e-inbody.com E-mail : info @inbody.com

Navigation menu