InFocus PBM PBM User Manual IN3902LB IN3904LB RG EN

Download:
Mirror Download [FCC.gov]
Document ID	1117206
Application ID	9EDmwLLjLldt7k+qwi6KFg==
Document Description	Users GUide part 1 of 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	204.86kB (2560695 bits)
Date Submitted	2009-05-29 00:00:00
Date Available	2009-05-29 00:00:00
Creation Date	2009-05-27 10:44:32
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2009-05-27 10:44:46
Document Title	IN3902LB_IN3904LB RG_EN.fm
Document Creator	FrameMaker 7.0
Document Author:	elio

LiteBoard™ Projector
IN3902LB IN3904LB
Regulatory models W3902, W3904
010-0728-00
Declaration of Conformity
FCC Warning
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville,
Oregon 97070 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The
Netherlands
We declare under our sole responsibility that this projector conform to the
following directives and norms:
EMC Directive 2004/108/EC
R&TTE Directive: 1999/5/EC
EuP Directive: 2005/32/EC
Low Voltage Directive: 2006/95/EC
ETSI: EN 300 440, EN 301 489
EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
Safety: IEC 60950-1:2005, MOD.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are trademarks or registered trademarks
of Apple Computer, Inc. IBM is a trademark or registered trademark of
International Business Machines, Inc. Microsoft, PowerPoint, and Windows
are trademarks or registered trademarks of Microsoft Corporation. Adobe
and Acrobat are trademarks or registered trademarks of Adobe Systems
Incorporated. DLP® and the DLP logo are registered trademarks of Texas
Instruments and BrilliantColor™ is a trademark of Texas Instruments.
InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks
or trademarks of InFocus Corporation in the United States and other
countries.
Changes or modifications not expressly approved by InFocus Corporation may void
authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
Agency Approvals
UL, cUL
NOTE: This product is covered electrical and electronic
equipment under the European Union's Waste from Electrical
and Electronic Equipment ("WEEE") Directive (2002/96/EC).
The WEEE Directive requires that covered equipment be
collected and managed separately from typical household waste
in all EU member states. Please follow the guidance of your local
environmental authority or ask the shop where you purchased
the product for collection or recycling options.
Other specific Country Approvals may apply. Please see product
certification label.
This document applies to regulatory models W3902 and W3904.
Input ratings: 100-240Vac, 3.3-1.2A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at
any time without notice.
Table of Contents
Introduction
Positioning the projector
Projector and device connector guide
Connecting a computer source
DisplayLink or VESA
Optional computer connections
Displaying an image
Adjusting the image
Connecting a video device
Video device connections
Composite video connection
HDMI 1.3 connection
S-video connection
VESA connection
Component video connection
LiteBoard™ Pen
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Dynamic Messaging
Using the menus
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Using Network Functions
Using LitePort
Maintenance
Cleaning the lens
Replacing the projection lamp
Using the security lock
10
10
10
12
13
14
15
15
15
15
15
15
16
20
20
28
29
30
31
31
32
32
32
33
34
35
36
38
39
43
46
46
47
48
•
•
•
•
•
•
•
•
•
•
•
2’ / 0
.6
8’ / 2
.4 m
5’
•
Refer to this guide for proper startup and shutdown procedures.
Follow all warnings and cautions in this manual and on the projector.
Do not look into the lens while the projector is being used.
Place the projector in a horizontal position no greater than 8 degrees off
axis.
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
Do not set up the projector in humid or dusty places or in places where
the projector may come into contact with smoke or steam.
Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
Use only the power cord provided. A surge-protected power strip is
recommended.
Do not overload wall outlets.
When disconnecting the power cord, hold the plug, not the cord.
Use only InFocus-approved ceiling mounts. Warning: To prevent eye
injury if the projector is ceiling mounted, wear protective eyewear
before opening lamp door. A warning sticker is included with the user
documentation. Place this sticker on the lamp door if the projector is
mounted on the ceiling.
The projector must be installed by a qualified professional in order to
ensure proper operation and reduce the risk of hazards or injury. It is
not recommended you install the projector yourself.
Refer all service to qualified service personnel. Servicing your own
projector can be dangerous to you and will void the warranty.
The projector remote control uses batteries. Make sure the batteries
polarity (+/-) is aligned correctly. Dispose of used batteries in
accordance with local disposal laws.
Wash hands after handling the cables supplied with this product.
Hg-Lamp contains mercury. Manage in accordance with local disposal
laws. See www.lamprecycle.org.
In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Keep people, food, and drinks out of the "keep out"
area under and around the projector, as indicated by the "X" areas
below.Only genuine InFocus lamps are tested for use in this projector.
InFocus is not liable for the performance, safety or certification of any
other lamps. The use of other lamps violates the projector warranty and
voids all certification marks on this projector. vents. Do not place the
projector on a tablecloth or other soft covering that may block vents.
/1
•
•
•
•
•
3’
Important Operating Considerations for Safety
1.5
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty Booklet.
Introduction
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing too. The IN3902LB has
native XGA 1024x768 resolution, and the IN3904LB has WXGA 1280x800
resolution. This guide applies to all products. They are compatible with a
wide variety of computers and video devices.
zoom (rear ring)
touch keypad
focus (front ring)
Product specifications
remote control
receiver (IR)
To read the latest specifications on your multimedia projector, be sure to
visit our website at www.infocus.com, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the
included Quick Start Poster/Booklet. Optional accessories can be found on
our website at www.infocus.com or at your retailer or dealer.
lens
elevator foot
Online registration
Register your projector on our website at www.infocus.com/register to
activate your warranty and receive product updates, announcements, and
registration incentives.
power cord
connector
elevator foot
connector
panel
remote control
receiver (IR)
Connector panel
The projector provides both computer and video connection options,
including:
•
VESA computer (2)
•
HDMI, for computer (1) and for video (1)
•
S-video
•
Composite video
•
Separate audio inputs for video and computer
•
USB DisplayLink connector, for computer audio/video input. This
USB connection also provides slide advance (and mouse control when
used with an optional remote control only)
composite
monitor out
video
audio in
HDMI for video
computer
S-video
The projector also provides the following connectors:
•
Monitor out, to provide an image on your desktop computer as well as
on the projection screen
•
LAN port for network control and web server.
•
LitePort, for connecting a USB flash drive containing images.
•
Audio out, to provide sound for external speakers
•
A 5 volt DC output (see below)
audio out
5 volt output
security lock
It also has an RS-232 connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
NOTE: DisplayLink video and audio is not sent to monitor out and audio
out.
5 volt DC output
The 3.5mm mini-jack triggers provide a 5 volt, 2 amp DC output. It provides
a constant output while the projector is on. It is designed to provide power
for an InFocus LiteShow II wireless device, which allows wireless
projection. More information can be found on our website at
www.infocus.com or at your retailer or dealer.
RS-232
DisplayLink
connector
Positioning the projector
Table 1: (IN3902LB)
Range of distance to the screen for a given screen size
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.5m) from the projection screen.
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase
extension cables). To ensure adequate cable access, do not place the
projector within 6 inches (.15m) of a wall or other object.
•
If you are installing the projector on the ceiling, refer to the installation
guide that comes with the Ceiling Mount Kit for more information. To
turn the image upside down, see “Ceiling mount” on page 31. We
recommend using an InFocus authorized ceiling mount.
•
•
Distance to screen
bottom of image
1.24 ft above center
of lens
lens center
Projection angle
10 ft high
image
(IN3902LB)
bottom of image
1.5 ft above center
of lens
Minimum
Distance (feet/
m)
60/1.5
80/2.0
90/2.3
150/3.8
8.6/2.6
11.5/3.5
12.9/3.9
21.5/6.6
7.8/2.4
10.4/3.2
11.7/3.6
19.5/5.9
Distance to screen
The image exits the projector at a given angle. IN3902LB image offset is
115% ; IN3904LB image offset is 112.4%. This means that if you have an
image 10’ high, the bottom of the image will be 1.5' (IN3902LB) and
1.24' (IN3904LB) above the center of the lens.
(IN3904LB)
Maximum
distance (feet/m)
Table 2: (IN3904LB)
Range of distance to the screen for a given screen size
Position the projector the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
10 ft high
image
Diagonal Screen
Size (inches/m)
Projection angle
lens center
Diagonal Screen
Size (inches/m)
Maximum
distance (feet/m)
Minimum
Distance (feet/
m)
60/1.5
80/2.0
90/2.3
150/3.8
7.3/2.2
9.7/2.9
10.9/3.3
18.1/5.5
6.5/2.0
8.7/2.7
9.8/3.0
16.3/5.0
Projector and device connector guide
The following illustration and table should help you find the connectors to
use and obtain the best resolution possible from your input devices, such as
computers, standard VCRs, DVD players (progressive and interlaced),
HDTV sources (1080i, 1080p and 720p HDTV formats), TV and satellite
tuners, camcorders, video games (progressive and interlaced), and laser
disc players.
composite
monitor out
video
audio in
audio out
HDMI for video
computer
S-video
5 volt output
security lock
RS-232
DisplayLink
connector
Video Device
Standard Broadcast TV (not
HDTV) via: cable, digital cable,
satellite TV, DVD, or VCR
Standard Video Camera
Video Compatibility
If Your Device
Connector Is
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Attach to Adapter or
Labeled Connector
on Projector
Composite or S-video
For Setup Instructions, see
Comments
Composite video connection on
page 15.
Not for progressive
(i.e. HDTV) sources.
See page 9.
S-video connection on page 15
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite or S-video
Composite video connection on
page 15.
Not for progressive
(i.e. HDTV) sources.
See page 9.
S-video connection on page 15
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Composite or S-video
Standard Video Game
Composite video connection on
page 15.
S-video connection on page 15
Not for progressive
(i.e. HDTV) sources.
See page 9.
Video Device
HDTV
(High Definition TV)
Video Compatibility
If Your Device
Connector Is
Attach to Adapter or
Labeled Connector
on Projector
For Setup Instructions, see
1080i, 1080p, 720p
VGA
VGA 2 or VGA 1
VESA connection on page 15
Component 480i
Component video
VGA 2 or VGA 1 via
optional VESA to
Component adapter
Component video connection on
page 15
HDMI
HDMI connection on page 15
Progressive DVD
1080i, 1080p, 720p
VGA
VGA 2 or VGA 1
VESA connection on page 15
Component 480p
and 480i
Component video
VGA 2 or VGA 1 via
optional VESA to
Component adapter
Component video connection on
page 15
HDMI
HDMI connection on page 15
Progressive Video Game
1080i, 1080p, 720p
VGA
VGA 2 or VGA 1
VESA connection on page 15
Component 480p
and 480i
Component video
VGA 2 or VGA 1 via
optional VESA to
Component adapter
Component video connection on
page 15
HDMI
HDMI connection on page 15
Comments
Connecting a computer source
DisplayLink or VESA
connect USB cable
If you have a Windows or Macintosh computer, connect the USB cable
between your computer's USB port and the projector's DisplayLink
connector*. Then to begin installation of the DisplayLink software:
Windows: Follow the instructions on the screen.
Macintosh: A folder will open containing a file named DisplayLink
Installer.pkg. Open that file and follow the instructions on the screen.
MOLEX
MOLEX
* For detailed DisplayLink instructions and troubleshooting, and to
download the latest DisplayLink software, go to www.infocus.com/
support/displaylink.
Or, connect one end of the provided computer cable to the VGA 1 or VGA 2
connector on the projector and the other to the VESA connector on your
computer. If you are using a desktop computer, you will need to disconnect
the monitor cable from the computer’s video port first (you can connect this
monitor cable to the Monitor Out connector on the projector, see below).
Connect the black power cord to the Power connector on the side of the
projector and to your electrical outlet. The Power light on the Status
Indicator Panel (page 20) turns amber.
NOTE: Always use the power cord that shipped with the projector.
connect computer cable
connect power cord
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In Computer connector on the
projector. You may also need an adapter.
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, connect the computer’s
monitor cable to the Monitor Out connector on the projector.
NOTE: Only VGA video is sent to the Monitor out connector.
To display a presentation from a USB flash drive, see the Using LitePort
section on page 43. This feature is eliminates the need for a computer source
and can be integrated with common wall plates and conference room
input/output panels.
To advance slides in a PowerPoint presentation using the remote control,
plug the USB cable between the projector's DisplayLink connector and your
computer. Then press the up and down arrow buttons on the remote control
to move through your slides.
connect audio cable
connect monitor cable
10
You can control the projector from an LCD control panel, touch screen, or
other control device or computer by connecting an RS-232 cable to the
projector’s Serial Control connector. Specific RS-232 commands can be
found in the Service and Support section of our website and in the
Appendix.
connect RS-232 cable
The projector can be managed by networking software through its Network
(RJ-45) connector. Detailed instructions on this feature can be found on our
website.
connect CAT-5 cable
11
Displaying an image
press Power button
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp
comes on, the start up screen displays and the Power button is steady green.
It can take a minute for the image to achieve full brightness.
? No start up screen? Get help on page 21.
turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If you are using a VESA cable to connect your computer to the projector (instead
of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/
LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop's documentation for
more information about your laptop's key combination or go to the InFocus
website at: http://www.infocus.com/Support/LaptopActivation.aspx.
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
? No laptop image? Try pressing the Auto Image button on the keypad.
Get help on page 21.
? Is your laptop connected to the projector's DisplayLink connector? See the
InFocus DisplayLink Software User's Guide (available on the InFocus
website at www.infocus.com/displaylink) for troubleshooting
information.
12
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the elevator foot
release button to extend the foot.
release button
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent at the side of the
projector.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See page 6 for a table listing screen sizes and distances.
Adjust the zoom or focus.
adjust zoom or focus
zoom (rear ring)
If the image is not square, first make sure that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
Adjust the Contrast or Brightness in the Basic Picture menu. See page 34 for
help with these menu adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 14.
adjust Basic Picture menu
13
focus (front ring)
Connecting a video device
4:3 screen
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. You can connect the audio directly to the projector to get sound
from the built-in speaker, or you can bypass the projector’s audio system
and connect the audio directly from your source to a stereo or home theater
system.
16:9 screen
Do Not Use
4:3
mode
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders,
and satellite TV boxes. Basically, any device that can change channels is
considered a tuner.
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
Resize button on the remote or through the projector’s Basic Picture Menu.
See page 34 for more information.
16:9
mode
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3. HDTV and most DVDs are 16:9. If you’re projecting onto a
screen, the size/shape of the screen may determine which aspect ratio to
use. If you are projecting onto a blank wall, you don’t have the screen size
restriction. What you plan to project will also help you choose between 4:3
and 16:9. Most TV shows are 4:3, while most movies are 16:9.
Native
mode
(NTSC
only)
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.
14
Video device connections
VESA connection
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This
connector may be labeled “To Monitor” on the video source. Plug the
computer cable into the VGA 2 or VGA 1 connector on the projector.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the
yellow Video 3 connector on the projector.
Component video connection
If your HD video device has component connectors, an optional
Component to VESA adapter can be used. Plug the component cable into
the video device. Plug the other end of the component cable into the adapter
and plug the adapter into the VGA 2 or VGA 1 connector. Component offers
the highest quality video output.
Plug the white connector of a Mini-plug audio Y-cable into the left audio
out connector on the video device and plug the red connector into the right
audio out connector on the video device. Plug the other end of the cable into
the Audio In Video connector on the projector.
Keep in mind that video output from composite connections is not as high
quality as S-video.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface.
HDMI provides an interface between sources, such as set-top boxes, DVD
players, and receivers and your projector. Plug an HDMI cable into the
video-out connector on the video device and into the HDMI connector on
the projector.
To take advantage of HDMI 1.3 Deep Color (30 bit) you must have a 1.3compatible source.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an Svideo cable into the S-video connector on your video device and into the
Video 2 connector on the projector. Use the audio cable as described above.
Keep in mind that S-video delivers higher quality video output than
composite.
15
LiteBoard™ Pen
computer is powered on). The battery light will stay on while the battery is
charging, then it will turn off when the battery is fully charged.
The LiteBoard pen works like a wireless mouse - but one that works in
midair, not on your desktop. Just hold the pen in your hand, and point it at
the projected image to point, click and drag. The pen works with all your
software, just like a regular mouse.
When charging is finished, you can disconnect the USB cable (or keep the
cable connected and use the pen while it°¶s charging).
Computer System Requirements and Connections
NOTE: 5-10 minutes of charging is enough for about an hour of pen use. A
full charge will take 6-8 hours and will allow 20-40 hours of non-stop pen
use.
For the pen to work, a LiteBoard-compatible projector needs to be powered
on and connected to your computer.
Caution: The lithium battery is only rechargeable, and is not user
serviceable or user replaceable.
Caution: Always use the included USB cable and power adapter (or your
computer) to charge the pen.
The LiteBoard pen is compatible with any computer and operating system
that supports a standard USB mouse (including Windows, Macintosh, and
Linux). To set up your computer with the pen, make sure a USB cable is
connected between your projector's DisplayLink connector and a USB port
on your computer.
How to Use the Pen
Follow these steps to use the pen:
1 Connect the projector and your computer with a USB cable (see Computer System Requirements and Connections above).
IMPORTANT: If you aren’t using DisplayLink to project, you must also
connect the computer’s display output to the projector using a VGA or
HDMI cable.
2 Make sure the pen's battery is charged or charging (see Charging the
Pen's Battery above).
3 Turn on the projector and make sure it's displaying the computer's
Charging the Pen’s Battery
screen - set the source to DisplayLink, VGA 1, VGA 2, or HDMI (press
the source button on the projector or its remote if needed - you may
need to press it several times).
When the pen’s amber battery light starts to blink, its internal battery is low
(if the battery is fully discharged, you won’t be able to turn the pen on by
pressing its tip, L or R buttons).
4 Turn on the pen by pressing its tip, L, or R button - the pen's green Link
light will start to blink.
To charge the battery, open the flap at the rear of the pen to expose the pen’s
USB connector. Then connect a USB cable between the pen and the USB
power adapter, or a computer (if connecting to a computer, make sure the
5 Point the pen at the screen to point, click, and drag - just like a normal
mouse.
16
NOTE: If the pen’s motion is too sensitive, press the M button on the pen to
change motion stabilization (see LiteBoard Pen Menu below for more
information).
6 When you’re done, set the pen aside and make sure it isn’t pointing at
the screen; it will turn itself off automatically after 30 minutes.
If you have problems, see Troubleshooting (below).
Pen Position and Avoiding Shadows
Your Location Distance from the Screen
You can use the LiteBoard pen right up against the screen, or from across
the room. You might find that your pointing accuracy will improve if you
get closer to the screen and avoid standing too far off to one side or the
other of the screen.
Using More than One Pen
The projector can work with more than one pen, but you can only use one
pen at a time. When you want to switch to a different pen:
1 Point the current pen away from the projected image for at least 3 sec-
Avoid Shadows!
onds.
The pen won't work if its tip is in a shadow or if it is pointing at a shadow:
2 Press the tip, L, or R button on the new pen to turn it on, and then start
Correct (no shadow)
using the new pen.
Incorrect (shadow)
NOTE: Settings in the projector's LiteBoard Pen menu (see below) apply to
all pens used with that projector.
Pen Features
How to Hold the Pen
You can hold the pen the way you would hold a normal pencil or pen, or
you can hold it like a remote control - use in whichever position is most
comfortable. NOTE: If the pen is up close to the screen, you can press its tip
against the screen's surface to click and drag.
Buttons and Pen Tip
The pen's three top buttons are equivalent to the left (labeled 'L'), right
(labeled 'R'), and middle (labeled 'M') buttons on a mouse. The pen's tip is
17
also a button, and it's also equivalent to the left mouse button. NOTE: By
default, the projector is set up to use the 'M' button to change whether the
pen's motion is stabilized - but you can change this button to perform other
functions, including a standard middle button mouse click (see LiteBoard
Pen Menu below).
Internal Radio
Battery Light
The amber battery light shows the status of the pen's built-in battery (see
below for battery information). The battery light will turn on while the pen
is charging, and it will blink if the battery is low (2-4 hours of pen use left).
Manufacturer: KAYO Battery (ShenZhen) Co., Ltd.
Model: ICR14430
Rating: 3.6VDC/650mAh
Caution: Lithium battery is only rechargeable, and not user replaceable. Not
user serviceable.
Link Light
LiteBoard Pen Menu
The green link light shows the status of the pen's wireless connection to the
projector. The link light will blink frequently (more than once per second)
when the pen is attempting to link to the projector; then it will blink less
frequently (about once every 4 seconds) after the pen has linked to the
projector. NOTE: The link light will stay off when the pen is off.
You can access the LiteBoard Pen menu from the projector's Setup menu. To
change the settings in this menu, highlight a setting, then press Select (on
the projector or its remote) one or more times - each press of Select will
change to the next value for the setting.
The pen has a built-in wireless transmitter/receiver which it uses to
communicate with the projector.
Lithium Battery Information
USB Connector
The pen's USB connector is behind a flap on the back of the pen. The USB
connector is only used for charging the pen's battery - using the included
USB power adapter, or a computer. NOTE: You can use the pen while
charging the battery, but after the battery is charged (battery light turns off),
you can unplug the USB cable and continue to use the pen without a cable.
Sensor
Enabled - Controls whether the projector lets you use LiteBoard pens. Set
this to Yes to allow pen use. Set this to No to prevent pen use.
The pen's optical sensor opening is located above the pen's tip. Don't block
the sensor, and make sure it always has a clear view of the screen. NOTE:
The sensor won't work if you point it at a shadow or away from the screen.
Stabilizer - Controls how (and if) pen motion is stabilized. Motion
stabilization helps you point and click accurately. When set to Auto, motion
is stabilized unless the pen's tip or L button is being pressed. When set to
On, motion is always stabilized; when set to Off motion is never stabilized.
Reset Button
The pen has a reset button, behind a small hole on its underside. Under
normal conditions, you should not need to reset the pen. See the
Troubleshooting section below for more information.
M Button - Selects the function of the pen's M Button. You can use the M
button to change motion stabilization, or perform keyboard or mouse
button shortcuts. NOTE: The PwrPnt Annotate setting sets up the M button
18
to control drawing (annotating) during Microsoft PowerPoint slide shows.
The first press of the M button will turn on the drawing function, the next
press will turn off the drawing function, the next press will turn it on again,
etc.
•
•
Link Channel - Selects the radio channel used for pen communication. This
should be set to Auto unless you encounter interference (see
Troubleshooting below for more information).
Troubleshooting LiteBoard
For the most up-to-date information, visit our support site at
www.infocus.com/support
•
•
If the pen doesn't work at all, or it works intermittently, try one of these
solutions:
- Press the tip, L, or R button on the pen to turn it on.
- If the pen's green Link light never blinks, then the pen's battery is fully
discharged; connect the pen to the USB power adapter or your
computer.
- Make sure the pen is not pointing at a shadow and make sure its tip is
not in a shadow.
- If the room is brightly lit, reduce the room illumination.
- If you're trying to use the computer's mouse at the same time as the
pen, point the pen away from the screen while using the mouse.
- If someone else is using a different pen with the same projector, they
must stop using it before you can use another pen.
- Change the Link Channel value in the LiteBoard Pen menu.
- Reset the pen: push the end of a paper clip into the reset opening on
the underside of the pen.
If accurate clicking is difficult, try one of these solutions:
- Hold the pen steadier when clicking.
- Use the pen right up against the screen so it's easier to avoid
unexpected movements.
- Change the Stabilizer value in the LiteBoard Pen menu to Auto or On.
19
If it's difficult to draw or move freely because the pen prefers moving
in straight lines, change the Stabilizer value in the LiteBoard Pen menu
to Auto or Off.
"If the mouse pointer is in the wrong place on the screen, or the mouse
pointer's movement is restricted to only part of the screen, try one of
these solutions:
- Make sure your projector is displaying the computer's screen and not
some other source (such as DVD, VCR, etc.). To change the source,
press the Source button on the projector or it's remote.
- Make sure the projector is displaying the same image as the
computer's main or built-in monitor (don't extend your desktop onto
multiple monitors). To correct this:
On Windows XP: Open the Display control panel, click Settings, click
the display that represents the projector, then un-check 'Extend my
Windows desktop...'.
On Windows Vista: Right-click on the desktop, choose Personalize°K,
click Display Settings, click the display that represents the projector,
then un-check 'Extend the desktop...'
On Macintosh: Select System Preferences from the Apple Menu, then
select Displays. Click Arrangement, and check 'Mirror Displays'.
•
If the battery light does not turn on when the pen is being charged, try
one of the following:
- Make sure a USB cable is connected between the pen and either the
USB power adapter, or a USB port on your computer.
- If the pen is connected to the USB power adapter, make sure the
adapter is plugged in to a live electrical outlet. If the pen is connected to
your computer, make sure the computer is powered on.
- If the pen still won't charge, contact InFocus support at
www.infocus.com/support.
•
If DisplayLink Manager setup always starts when USB cable is
connected, but you don't want to use DisplayLink projection, you can
disable DisplayLink: Go into the projector's Setup menu and turn off
the DisplayLink Source setting. NOTE: This does not disable the
DisplayLink connector; it only disables being able to project over
DisplayLink.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Modify Date                     : 2009:05:27 10:44:46-07:00
Create Date                     : 2009:05:27 10:44:32-07:00
Title                           : IN3902LB_IN3904LB RG_EN.fm
Author                          : elio
Creator                         : FrameMaker 7.0
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Page Count                      : 20
Mod Date                        : 2009:05:27 10:44:46-07:00
Creation Date                   : 2009:05:27 10:44:32-07:00
Metadata Date                   : 2009:05:27 10:44:46-07:00

EXIF Metadata provided by EXIF.tools