Indyme Solutions CB951 Wireless Access Point User Manual

Indyme Solutions, Inc Wireless Access Point CB451C Installation Guide

a href="https://usermanual.wiki/Indyme-Solutions" itemprop="url"> Indyme Solutions >

user manual

Technical Document CB951 Installation Guide Page 1 P/N 430697-00 Rev C CB951 Access Point Installation Guide The CB951 is a multi-band access point designed to decode radio frequency transmissions from any of Indyme’s multi-band wireless callboxes. The signals are relayed, via the LAN, to an Indyme server for processing. Connections to the CB951 will vary depending on the deployed configuration. The CB951 can be programmed to function in the 868MHz or 900MHz frequency spectrum. Check your configuration for details. Installation The CB951 Access Point is a ceiling-mounted device. Plan the installation such that each unit has the clearest possible “line-of-sight” to the largest possible expanse of the sales floor. The CB951 Access Point must be programmed before installation. Confirm the correct antenna is installed and all operational parameters have been set prior to installing the CB951 Access Points. Each unit will require power; this can be supplied via P.O.E. or external power supply to each unit. (12VDC, 500mA, positive tip, 2.5mm – SOLD SEPARATELY). Tools Needed: • Drill and assorted Drill Bits • Assorted Screwdrivers (Phillips and Flat Blade) • Wire Cutters Equipment Needed: • CB951 Access Point • Four (4) pair CAT5 Network Cable NOTE: Grey: 868 MHz Europe Yellow: 900 MHz USA/Australia * Plan your cable runs to avoid the following potential sources of interference; DO NOT LAY CABLE ON OR NEAR Fluorescent lighting fixtures, AC power lines, fan motors or RF transmitters. * Assure a clear line of sight between the Access Point and installed Callboxes, avoiding large metallic objects such as storage racks and air ducting. * Leave at least 15 feet of excess cable at the Access Point location, in the event that the unit needs to be relocated. * Do not bundle the cable with other data cables, as “bleed-over” may occur, causing interference.
Technical Document CB951 Installation Guide Page 2 P/N 430697-00 Rev C Position and Install the CB951 Access Point Depending on the location and the ceiling type, the CB951 Access Point can be mounted on a beam or through a ceiling tile: • Tile/Ceiling-mounted CB951: Install the unit above the ceiling tile with the antenna and LED barrel protruding through the ceiling tile. Verify that the LED barrel and antenna are visible from the sales floor. • Open-Beam-mounted CB951: Using zip-ties or hardware, attach the CB951 Access Point to the bottom of the beam. Verify that the LED barrel and antenna are visible from the sales floor. Try to mount the Access Point lower than nearby ducting and electrical conduits. Wiring The CB951 can be wired using an RJ-45 connector, (568B standard LAN), using CAT5 Network Cable. The CB951 must be connected using one of the following: • P.O.E. Switch: Using a CAT5 Network Cable connect one RJ45 to the LAN port on the CB951 Access Point. Connect the other end of the cable to an available port on the P.O.E. switch. • Standard Switch: Using a CAT5 Network Cable connect one RJ45 to the LAN port on the CB951 Access Point. Connect the other end of the cable to an available port on the switch. Connect the AC adapter to an available power outlet, connect the other end to the DC power jack on the Access Point. To 12VDC Adapter (positive tip) To network P.O.E. switch or Standard switch CB951 Mounting Template Depending on the location of the Access Point and the ceiling type, the following template may be used to accurately mark the holes for the antenna and the indicator L.E.D. The CB951 Access Point can be mounted on a beam or through a ceiling tile.
Download:
Mirror Download [FCC.gov]
Document ID1561907
Application IDCQvvLtQTPhRu5L0pccPn3Q==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize6.16kB (76950 bits)
Date Submitted2011-10-18 00:00:00
Date Available2011-10-19 00:00:00
Creation Date2011-01-31 16:11:59
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2011-01-31 16:12:09
Document TitleCB451C Installation Guide
Document CreatorAcrobat PDFMaker 7.0.7 for Word
Document Author: Jim Bender
FCC ID Filing: J69CB951

Navigation menu