Indyme Solutions GENCLBX Call Box Transmitter User Manual Installation Guide
Indyme Solutions, Inc Call Box Transmitter Installation Guide
Contents
Installation Guide
INDYELE Technical Document CB440/CBS11 Installation And Programming lnstruction Individual callbox addresses should be determined prior to smrting the installations programmed callbox defaults to an address of 001, this position in the control unit m or have an advisory message. Location Considerations Call boxes are generally best located at areas that require assistance to access store merchandise, such as high shelving, chain and rope cutting, key machine, etc. Stores and installers should be aware of Am ricans With Disabilities Act (ADA) requirements for accessibility. The call boxes utilize a very low powered transmitter, and s operate best with a clear line of sight to the nearest receiver. Tall shelving, merchandise and metal signs c reduce the oallbox signal. Install the Cell Box 1. Verify call box placement with the , me the best mounting ramming. case, affix the double-sided foam tape to the es and Mode for each call box are listed in the Store Installation and on Manual for the specific store install. Refer to the data tables in Appendix A of tore Installation and Operation Manual for the correct Mode and Address for each ball box you are programming. Press and hold the RESET button for approximately 5 seconds. LED 1 will flash to indicate the call box is in address programming mode. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. Press the RESET button when finished with the hundreds digit. Press button 1 to increment the tens digit, LED 1 will flash with each press. QPPNT‘ CB440/51 1 Install Instructions 1 P/N: 430223410 Rev H Press the RESET button when finished with the tens digit. Press button 1 to increment the ones digit. LED 1 will flash with each press. Press the RESET button when finished with the ones digit. The address just programmed should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying on. longer period of time, approximately 1 second). semen JP1 Power: must be installed JP4 Pulse Width: must be 5 during cell box programming, Pulse Width operation and de Program Enable: must be ns led during call box programming. A for 05440 and 05511 ‘ [Box PCA has seven operating modes as in TSNDO1: Wireless insballation, each call box is programmed at the factory. If it oessary o re-program the call box, please refer to the TSN001 in the Store d O ration Manual for additional programming features and die. It the manual is not available, please contact the Indyme Help Desk at 41 for additional support. older models of these cell boxes are not "Mode“ programmable, Before programming these ll boxes, identify what model of circuit board is installed in the unit as per the serial number or he PCA illustration above. FCC Notice Of Compliance: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful inference and (2) This device must accept any imerlerenoe received, including any Interference that may cause undesired operation, Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. 05440/51 1 Install Instructions 2 P/N.‘ 430223—00 Rev H Technical Document CB475 Installation And Programming Instruction Individual callbox addresses should be determined prior to starting call box installations. As an programmed callbox defaults to an address of 001 this position in the control unit may be g or have an advisory messme. Installing CB475 Call Boxes Locatlon Considerations Call boxes are generally best located at areas that require as ' access store merchandise. such as: high shelving, chain key machines. Stores and installers should be aware Disabilities Act (ADA) requirements for accessibility. The 03475 call boxes utilize a very low powered transmitter best with a clear line of sight to the neare merchandise and metal signs can blo Install the Call Box 1. For ADA compliant locations, m' floor. Mark this h mend use , ‘r ofthe bottom on page 2 of this 4 ch bracket has three holes. Use the two holes nd secure the bottom bracket to the drywall, using a loo ens on the wall. Use the provided self-tapping TEK screws (p/n: 0200-20) to secure the bracket to the mounting surface. If necessary, drill 0 pilot holes using a 5/32" bit, then install the self-tapping TEK screws. For masonry mountlng: Mark the bottom bracket holes. using the two holes furthest from one another. Use a V4” masonry bit and drill a hole deep enough (approximately 1") for the green plastic masonry anchors (pln: 180064-00), Install the masonry anchors. and secure the bracket with provided anchor- screws . 3. Install the top mounting bracket using the same hardware and technique as used for the bottom bracket. Measure up 24" from the middle of the installed bottom bracket and position the middle of the top bracket here. A level should be used to insure that the installed callbox will be plumb. 4. Start one slotted hex-washer head screw (p/n: 180066-00) in each bracket. 054 75 Install Instructions 1 P/N: 430262—00 Rev E Technical Document CB475 Installation And Programming Instruction Individual callbox addresses should be determined prior to starting call box installations. As an un- prcgrammed callbox defaults to an address of 001, this position in the control unit may be or have an advisory message. Installing CB475 Call Boxes Locatlon Considerations Call boxes are generally best located at areas that require as ' access store merchandise, such as: high shelving, chain and key machines. Stores and installers should be aware Disabilities Act (ADA) requirements for accessibility. best with a clear line of eight to the neare merchandise and metal signs can blo Install the Call Box 1. For ADA compliant locations, m' floor. Mark this h r ofthe bottom ' on page 2 ofthis tic drywall anchors and screws (p/n: 180060-00) provided. I (shelvlng) or wood mountlng: Each bracket has three a lo ‘ ns on the wall. Use the provided selflapping TEK screws (p/n: 0200-20) to secure the bracket to the mounting surface. If necessary, driil pilot holes using a 5/32" bit, then install the self-tapping TEK screws. or masonry mountlng: Mark the bottom bracket holes, using the two holes furthest from one another. Use a V4" masonry bit and drill a hole deep enough (approximately 1") for the green plastic masonry anchors (p/n: 180064-00). Install the masonry anchors, and secure the bracket with provided anchor- SCIEWS . 3. Install the to mountin racket using the same hardware and technique as used for the bottom bracket. Measure up 24" from the middle of the installed bottom bracket and position the middle of the top bracket here. A level should be used to insure that the installed callbox will be plumb. 4. Start one slotted hex~washer head screw (p/n: 180066-00) in each bracket. 054 75 Install Instructions 1 P/N: 430262470 Rev E INDYME Technical Document 5. Install the signs (if not already installed) imo the sign extrusion. Install the top and bottom caps. 6. Install the call box by sliding it over the brackets. Position the bottom of the callbox flush with the lower edge of the bottom bracket. Verify the red antenna wire (from the PCA inside the call box) is routed up the back inside of the sign blade 7. Firmly tighten the slotted hex- washer head screw with a nut— driver The scr not have to be extremely tight to hold the callbox. TOP Self-taping plnch screw installation Programml to the data tables in Appendix A of the Store Installation and Mode and Address for each call box you are programming Press and hold the RESET button for approximately 5 seconds. . LED 1 will flash to indicate the call box is in address programming mode. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. Press the RESET button when finished with the hundreds digit. Press button 1 to increment the tens digit. LED 1 will flash with each press. Press the RESET button when finished with the tens digit. Press button 1 to increment the ones digit. LED 1 will flash with each press. Press the RESET button when finished with the ones digit. 3. 4. 5. G. 7. B. 054 75 Install Instructions 2 P/N: 430262410 Rev E ilNiLYMEJ Technical D6cuntent 9. The address just programmed should flash back on the LED 1 with a pause between each digit. (Note: the LED will indicate a zero value by staying on tor a longer period of time. approximately 1 second). JP! Power: must be installed JP4 Pulse Width: must be installed for Nar fl “ during call box programming. Pulse Width operation and pragmmmin Enable: must be JP2.‘ NOT installed d l! box programming. n. each call box is programmed at the factory. the call box, please refer to the TSN001 in the ass call boxes are not "Mode" programmable. Before programming these rify what model of circuit board is installed in the unit as per the serial number or ation above. ea 01 Compllance: This equipment complies with Part 15 of the FCC Rules. Operation is subjectlo the following two mnditlons: (1) This device must not cause harmful inference and (2) This device must accept any interlerenoe received, including any interference that may cause undesired operation. Any changes or modifications not expressly approved by the manulacmrer could void the user's authority to operate the equipment, 054 75 Install Instructions 3 P/N.‘ 430262470 Flev E lIN11ME Techflfcal Document 08514 Installation And Programming Instruction Individual callbox addresses should be determined prior to starting the installations. As an programmed callbox defaults to an address of 001 , this position in the control unit may hem blank or have an advisory message. Location Considerations Director call boxes are generally best located in high volume areas that demand a way to request additional services quickly, such as front registers or service counters. Stores and installers should be aware of Americans With Disabilities Act (ADA) requirements for accessibility. The call boxes utilize a very low powered transmitter. and best with a clear line of sight to the nearest receiver. Tall merchandise and metal signs can block or reduce the callbo signal. Install the 63514 Call Box 1. Verify call box and clear plastic lab sleeve is optional and may not be used 2. Identify which side of the 08514 the and avoiding damag 3. Slide the label int §tore Manager. (The label attached for the best visibility on the Iefl or right side of the call box). Ie-sided tape or Velcro will be installed on Programmi ' To program the th button and the remaining three buttons are automatically ical valtles. When the call box “flashes" the newly programmed “cated by a longer (slightly over a second) flash. For example: an long flash (0), pause. long flash(0), pause, and a short flash (1). specific store install. Refer to the data tables in Appendix A of the Store Insfamand Ogerarlon Manual for the correct Mode and Address for each call box you are prog ram-hing. Press and hold the FIESET button for approximately 5 seconds. LED 1 will flash to indicate the call box is in address programming mode. Press button 1 to increment the hundreds digit. LED 1 will flash with each press. Press the RESET button when finished with the hundreds digit. Press button 1 to increment the tens digit. LED 1 will flash with each press. Eflzbwpr‘ CB514 Install Instructions 1 P/N: 460223411 Rev B iINL'YME; Technical Document Press the RESET button when finished with the tens digit. Press button 1 to increment the ones digit. LED 1 will flash with each press. Press the RESET button when finished with the ones digit. The address just programmed should flash back on the LED 1 with a pause between each digit. (Nate: the LED will indicate a zero value by slay/rig on for a longer period a the approximately 1 second). * sows? JP4 Pulse Width: must be instel JF1 Power: must be installed during call box programming. ‘ boxes, identify what model or circuit board is installed in the unit as per the serial number or POA illustration above. FCC Notice 0! Compliance: This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful inference and (2) This device must accept any interference received, including any Interterence that may cause undesired operation Any changes or modifications not expressly approved by the manufacturer oould void the user's authority to operate the equipment. 05514 Install Instructions 2 P/NI 460223471 Rev B
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 8 Creator : Installation Guide - Microsoft Word Create Date : 2002:08:28 13:48:09 Title : Installation Guide.doc Author : DGodfrey Producer : Acrobat PDFWriter 5.0 for Windows NTEXIF Metadata provided by EXIF.tools