Infinity 3 Way Component System 653 1Cs Users Manual Kappa 653.1cs OM
653.1cs to the manual b0edcf59-fa98-4b85-a651-d6a0e9f069ce
2015-01-23
: Infinity Infinity-3-Way-Component-System-653-1Cs-Users-Manual-342830 infinity-3-way-component-system-653-1cs-users-manual-342830 infinity pdf
Open the PDF directly: View PDF .
Page Count: 4
Download | |
Open PDF In Browser | View PDF |
Kappa 653.1cs OM 7/14/98 10:10 AM Page 1 653.1cs, 1.1cs INSTRUCTIONS ® Thank you for purchasing an Infinity Kappa Series 3-Way Component System. We’ve organized this manual to make your installation as simple and trouble-free as possible. Please read it thoroughly before proceeding. Remember to keep your sales receipt with this manual in a safe place so both are available for future reference. K APPA S ERIES RIGHT + – Amplifier – + LEFT GRN GRN/BLK RED + GRN/WHT – BLK GRN BLK – + RED Connect Pigtail Jumpers As Shown – – + + – – + + – MIDRANGE EMIT TWEETER EMIT TWEETER MIDRANGE + WOOFER FROM LEFT AMPLIFIERS BLU/BLK Component System Crossover Network TO LEFT MIDRANGE + – LO GRY/ BLK TO LEFT TWEETER + – HI LO MID HI RED/ BLK GRY RED TO RIGHT TWEETER + HI MID LO LO HI REFERENCE STANDARD AUTOMOTIVE BLU Figure 1. This application shows connections for a Kappa1cs system and one stereo amplifier. TO RIGHT WOOFER + + HI HI To LEFT Woofer – – – LO -2- Single Stereo Amplifier TO LEFT WOOFER + Kappa speakers are designed to be easily installed in stock speaker locations. While mounting your speakers in the original factory locations will, in most cases, provide excellent sonic results, the best sounding installations are a result of adherence to a few basic rules: • For the most spacious stereo image, place the left and right speakers as far apart as possible. • For enhanced center image, place the left and right speakers so they are equidistant from the listening position. If possible, try to place them as far forward as possible. • For best treble response aim the tweeters toward the listening position, and be sure there are no obstructions between the tweeters and the listener. • Always wear protective eyewear when using any tools. • Turn off all audio systems and other electrical devices before you start. Disconnect the (–) negative lead from your vehicle’s battery. • Keep components in their package until final installation. When moving a speaker, always rest it with the cone or dome facing up. Never use force to install any speaker. • Check clearances on both sides of a planned mounting surface before drilling any holes or installing any screws. Remember that the screws can extend behind the surface. • At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. CAUTION: In some cars, fuel tanks may be located directly beneath the rear deck. Check for adequate speaker basket clearance before considering this location! • Before drilling or cutting holes, use a utility knife to remove unwanted fabric or vinyl, to keep material from snagging in a drill bit or saw. • For door installations, check the clearance with the windows throughout the range of the window’s travel, and verify that a mounted speaker will not interfere with the window crank or power window mechanism. • If mounting components elsewhere, check for clearance around rear deck torsion bars, glove box or other structural elements. • Do not mount components where they will get wet. – SPEAKER PLACEMENT WIRE CODES – WARNING: Playing loud music in an automotive environment can permanently damage your hearing, as well as hinder your ability to hear traffic. The maximum volume levels achievable with Infinity speakers, combined with high power amplification, may exceed safe levels for extended listening. We recommend using low volume levels when driving. Infinity accepts no liability for hearing loss, bodily injury or property damage as a result of use or misuse of this product. INSTALLATION WARNINGS AND TIPS FROM RIGHT AMPLIFIERS IMPORTANT: Installation of automotive stereo components can require extensive experience with a variety of mechanical and electrical procedures. Although these instructions explain how to install a Kappa Series 3-Way Component System in a general sense, they do not show the exact installation methods for your particular vehicle. If you do not feel you have the experience, do not attempt the installation yourself, but instead ask your Authorized Infinity Car Audio Dealer about professional installation options. Page 2 + 7/14/98 10:10 AM WOOFER Kappa 653.1cs OM HI + HI LO RED/ WHT RED – + HI – GRY/ WHT GRY + HI – To LEFT 4" Midrange To RIGHT 4" Midrange – + MID To LEFT Tweeter + MID – To RIGHT Tweeter To RIGHT Woofer BLU TO RIGHT MIDRANGE + – BLU/WHT Kappa 653.1cs OM 7/14/98 10:10 AM Page 3 MIDRANGE INSTALLATION TWEETER INSTALLATION Bi-Amp RIGHT + – + – + RED + – – – + + EMIT TWEETER MIDRANGE WOOFER FROM LEFT AMPLIFIERS ❶ TO LEFT MIDRANGE + – HI LO MID TO RIGHT TWEETER + HI HI MID LO RED/ BLK GRY – RED RED EMIT TWEETER MIDRANGE WOOFER FROM LEFT AMPLIFIERS – + LEFT LO HI – – Component System Crossover Network TO LEFT MIDRANGE + LO TO LEFT TWEETER + – HI LO MID HI RED/ BLK GRY RED TO RIGHT TWEETER + HI MID LO LO REFERENCE STANDARD AUTOMOTIVE HI TO RIGHT WOOFER + HI (Woofers) – LO TO LEFT WOOFER + + HI – ❷ – – GRY/ BLK RIGHT + – + BLU/BLK To LEFT Woofer BLU Amplifier – + + – – + + To Woofer Amplifier RIGHT ❷+ – – – + LEFT – MIDRANGE EMIT TWEETER ❶ To Midrange Amplifier RIGHT ❶ + Figure 4. Installing a Kappa1.1cs/653.1cs woofer above a deck or (with the enclosed spacer) below a deck. NOTE: Use the mounting clips as nuts to secure the below-deck installation. GRN GRN/WHT HI + HI LO RED – + HI BLU/WHT To RIGHT Woofer BLU TO RIGHT MIDRANGE + – RED/ WHT – GRY/ WHT GRY + HI – To LEFT 4" Midrange To RIGHT 4" Midrange – + MID To LEFT Tweeter WOOFER INSTALLATION Figure 6. After installing the surface-mount plate, slide the Kappa1.1cs EMIT-N™ tweeter down on the plate to lock in place. FROM RIGHT AMPLIFIERS Amplifier (Midrange) To RIGHT Tweeter GRN/BLK Remove Pigtail Figure 2. This application shows connections for a Kappa1cs system and two stereo amplifiers. + MID – To LEFT Tweeter RIGHT + – GRY/ WHT To RIGHT 4" Midrange – + MID GRN Figure 5. Installing a Kappa 1.1cs/653.1cs midrange driver in a door panel. – LO + HI – To LEFT 4" Midrange RIGHT + – BLU GRY – + HI Tri-Amp HI RED/ WHT To RIGHT Woofer HI + TO RIGHT MIDRANGE + – LO TO LEFT TWEETER + + HI Component System Crossover Network BLU/WHT WOOFER LO TO LEFT WOOFER + REFERENCE STANDARD AUTOMOTIVE – – + LEFT TO RIGHT WOOFER + – + HI – – – GRY/ BLK (Tweeters) + BLU/BLK To LEFT Woofer BLU Amplifier – BLK – MIDRANGE EMIT TWEETER + – – sacle = 70% RED – BLK + ❶ FROM RIGHT AMPLIFIERS + RIGHT + – – + LEFT – + (Woofers) To Woofer Amplifier RIGHT GRN/BLK GRN Connect Pigtail Jumpers As Shown Amplifier GRN GRN/WHT – + LEFT WOOFER Amplifier (Tweeter & Mids) + MID – To RIGHT Tweeter Figure 3. This application shows connections for a Kappa1cs system and three stereo amplifiers. Figure 7. After sliding down the flush-mount clip onto the back of the Kappa1.1cs EMIT-N tweeter, use the supplied hardware to fasten the cup to the panel. -3- Kappa 653.1cs OM 7/14/98 10:10 AM Page 4 ADJUSTING THE SOUND A NOTE ON POWER HANDLING SPECIFICATIONS After you have connected all the speakers to the crossover according to the connection diagram, you may adjust the overall sound of the system to suit your taste. The output of the woofers may be decreased by moving the woofer + connection at the crossover to the low position. The output of the midrange may be decreased by moving the midrange + connection at the crossover to the low position. The output of the tweeter may be increased by moving the tweeter + connection at the crossover to the high position or decreased by moving it to the low position. The speakers used in Kappa Series 3-Way Component Systems are designed to produce reasonable volume levels with little amplifier power. However, the addition of an amplifier to drive your speakers and a subwoofer will enhance the dynamic range of your system, and help overcome the ambient noise in a moving vehicle. Kappa speakers are designed to handle the power of a dedicated amplifier driven at or below its rated power. If an amplifier is driven far above its rated power, the output signal will “clip,” and the additional power present in a clipped signal can damage any speaker. Distorted or “fuzzy” sound from your speakers is an indication that the amplifier has exceeded its rated power, and you should reduce the volume level 653.1cs Type: Speaker Impedance: Power Handling: Frequency Response (±3dB): Sensitivity: Crossover Frequencies: GENERAL CARE The loudspeaker grilles may be cleaned with a slightly damp cloth. Do not use any cleaners or solvents on the grilles or the speaker cones. DECLARATION OF CONFORMITY We, Infinity Systems A/S Kongevejen 194B DK-3460 Birkerød DENMARK declare in own responsibility, that the products described in this owner’s manual are in compliance with technical standards: EN 50 081-1/1992 Steen Michaelsen EN 50 082-1/3.1995 Infinity Systems A/S Birkerød. DENMARK. 2/98 ® Infinity Systems, Inc. • 250 Crossways Park Drive, Woodbury, NY 11797 USA • (516) 496-3400 • FAX (516) 682-3583 Mounting Depth, Drop-in Woofer: Cut-out Diameter Woofer: Mounting Depth, Drop-in Midrange: Cut-out Diameter Midrange: Mounting Depth Tweeter: Cut-out Diameter Tweeter: 6-1/2" 3-Way System 4 ohms 120 watts per channel 50Hz ~ 45kHz 89Hz @ 2.83 V, 1 watt Woofer Hi terminal: 210Hz Lo terminal: 130Hz Midrange: 400Hz Tweeter: 12.5kHz 2-1/2" (67.5 mm) 5-11/16" (149 mm) 1-13/16" (46 mm) 3-3/4" (96 mm) 1" (25.4 mm) 3-3/8" x 1-3/4" (84.6 mm x 44.7 mm) 1.1cs Type: Speaker Impedance: Power Handling: Frequency Response (±3dB): Sensitivity: Crossover Frequencies: Mounting Depth Drop-in Woofer: Cut-out Diameter Woofer: Mounting Depth, Drop-in Midrange: Cut-out Diameter Midrange: Mounting Depth Tweeter: Cut-out Diameter Tweeter: 6" x 9" 3-Way System 4 ohms 200 watts per channel 36Hz ~ 45kHz 89Hz @ 2.83 V, 1 watt Woofer Hi terminal: 210Hz Lo terminal: 130Hz Midrange: 400Hz Tweeter:12.5kHz 2-9/16" (65 mm) 5-11/16" x 8-3/4" (149 mm x 223 mm) 1-13/16" (46 mm) 3-3/4" (96 mm) 1" (25.4 mm) 3-3/8" x 1-3/4" (84.6 mm x 44.7 mm)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 1998:07:14 10:11:12 Producer : Acrobat Distiller 3.01 for Power Macintosh Author : Tweety Creator : QuarkXPressª: LaserWriter 8 8.5.1 Title : Kappa 653.1cs OM Modify Date : 1998:07:14 10:12:46 Page Count : 4EXIF Metadata provided by EXIF.tools