Infocus Screenplay 4805 Users Manual

4805 to the manual 41e4b390-5c6b-4045-9073-fcff46033f25

: Infocus Infocus-Screenplay-4805-Users-Manual-393481 infocus-screenplay-4805-users-manual-393481 infocus pdf

Open the PDF directly: View PDF .
Page Count: 1

1

Declaration of Conformity

Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon

97070 USA

European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands

We declare under our sole responsibility that this projector conform to the following

directives and norms:

EMC Directive 89/336/EEC, Amended by 93/68/EEC

EMC: EN 55022

EN 55024

EN 61000-3-2

EN 61000-3-3

Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC

Safety: EN 60950: 2000

April, 2004

Trademarks

Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple

Computer, Inc. IBM is a trademark or registered trademark of International Business

Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered

trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or

registered trademarks of Adobe Systems Incorporated. Digital Light Processing is a

trademark or registered trademark of Texas Instruments. Faroudja, DCDi, and

TrueLife are trademarks or registered trademarks of Faroudja. InFocus and

ScreenPlay are trademarks or registered trademarks of InFocus Corporation. InFocus,

ProjectorManager, ProjectorNet, and LP are trademarks or registered trademarks of

InFocus Corporation.

FCC Warning

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

--Consult the dealer or an experienced radio/TV technician for help.

Canada

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Agency Approvals

UL, cUL, TUV, GOST

Other specific Country Approvals may apply. Please see product certification label.

InFocus reserves the right to alter product offerings and specifications at any time

without notice.

SP4805-02_usrguide.fm Page 1 Friday, June 11, 2004 8:22 AM

2

Table of Contents

Introduction 4

Positioning the projector 6

Projector and Device Connector Guide 7

Computer connections 7

Video connections 7

Connecting a computer source 10

Required computer connections 10

Optional computer connections 10

Displaying a computer source image 11

Adjusting the image 12

Using the projector with Windows 98 for the first time 13

Connecting a video device 15

Video device connections 16

Composite (RCA) video connection 16

S-video connection 16

Component (RCA) connection 17

DVI connection 17

Displaying video 18

Adjusting the image 18

Shutting down the projector 20

Troubleshooting your setup 20

Using the remote control 28

Using the audio 29

Using the keypad buttons 30

Optimizing computer images 31

Optimizing video images 31

Customizing the projector 31

Using the menus 32

Picture menu 33

Settings menu 38

Maintenance 40

Cleaning the Lens 40

Replacing the Projection Lamp 40

Cleaning the Lamp Housing Screens 42

Using the security lock 42

Appendix 43

Projected Image Size 43

Red LED Behavior and Projector Errors 44

If you are experienced in setting up projection systems, use the Quick Setup

card that is included with the projector. For complete details on connecting

and operating the projector, refer to this User’s Guide. Electronic versions of

this User’s Guide in multiple languages are available on our website.

The website also has technical specifications (an interactive image size cal-

culator, laptop activation commands, connector pin outs, a glossary, the

product data sheet), a web store to buy accessories, and a page for online

registration.

SP4805-02_usrguide.fm Page 2 Friday, June 11, 2004 8:22 AM

3

Important Operating Considerations for Safety

• Place the projector in a horizontal position no greater than 15 degrees

off axis.

• Locate the projector in a well-ventilated area without any obstructions

to intake or exhaust vents. Do not place the projector on a tablecloth or

other soft covering that may block the vents.

• Locate the projector at least 4' (1.2 m) away from any heating or cooling

vents.

• Use only InFocus-approved ceiling mounts.

• Use only the power cord provided. A surge-protected power strip is

recommended.

• Refer to this manual for proper startup and shutdown procedures.

• In the unlikely event of the lamp rupturing, discard any edible items

placed in the surrounding area and thoroughly clean the area along all

sides of the projector. Wash hands after cleaning the area and handling

the ruptured lamp. This product has a lamp which contains a very

small amount of mercury. Dispose of it as required by local, state or

federal ordinances and regulations. For more information see

www.eiae.org.

Follow these instructions to help ensure image quality and lamp life over

the life of the projector. Failure to follow these instructions may affect the

warranty. For complete details of the warranty, see the Warranty section at

the end of this User's Guide.

2 ft (.6m)

Do not place objects or people in the 2 foot (.6m) area along the front of the projector.

For ceiling mount applications, this area should be 5 feet (1.5m).

5 ft (1.5m)

SP4805-02_usrguide.fm Page 3 Friday, June 11, 2004 8:22 AM

4

Introduction

Congratulations and thank you for your excellent choice of a superior digi-

tal image projection device. Your new InFocus® ScreenPlay™ 4805 projector

is specifically designed for home cinema applications. The ScreenPlay 4805

sets a high standard using the latest DLP™ technology and new DCDi Plus

video processing from Faroudja™. Whether you are watching movies or

High Definition broadcasts or playing the latest video game, you will enjoy

amazing image quality.

Product specifications

To read the latest specifications on your multimedia projector, be sure to

visit our website, as specifications are subject to change. Web address infor-

mation is located on the back inside cover of this User’s Guide.

Accessories

The standard accessories that came with your projector can be found on the

included packing list. Optional accessories are listed in the Accessories cata-

log that came with the projector and can also found on our website. See the

inside back cover for the Web address.

Online Registration

Register your projector on our website to receive product updates,

announcements, and registration incentives. See the inside back cover for

the Web address.

5

Connector Panel

The projector provides both computer and video connection options,

including:

•DVI (M1-DA)

•Component SD/ED/HD (RCA)

• S-video

• Composite audio/video (RCA)

The projector also provides the following connectors:

• Audio out

• 12 volt DC output (see below)

12 volt DC output

The 3.5mm mini-jack trigger provides a 12 volt DC output. It provides a

constant output while the projector is on. It has numerous uses. For exam-

ple, if you connect your projection screen to the 12 volt DC output with the

cable that came with your screen, when you turn on the projector the screen

will move down; when you turn the projector off, the screen will return to

the storage position. To use the 12 volt DC output, you must first remove

the safety plug and turn Screen Trigger on in the System menu (see

page 38).

DVI S-video

12 volt audio

DC output out

RCA component

RCA audio/visual

(composite)

12 volt DC output

+12v ground

3.5mm plug

to, for example, screen relay (see screen manufacturer

for details)

SP4805-02_usrguide.fm Page 5 Friday, June 11, 2004 8:22 AM

6

Positioning the projector

To determine where to position the projector, consider the size and shape of

your screen, the location of your power outlets, and the distance between

the projector and the rest of your equipment. Here are some general guide-

lines:

• Position the projector on a flat surface at a right angle to the screen. The

projector must be at least 4.9 feet (1.49m) from the projection screen.

• Position the projector within 10 feet (3m) of your power source and

within 6 feet (1.8m) of your video device (unless you purchase exten-

sion cables). To ensure adequate cable access, do not place the projector

within 6 inches (.15m) of a wall or other object.

• If you are installing the projector on the ceiling, refer to the installation

guide that comes with the Ceiling Mount Kit for more information. To

turn the image upside down, see “Ceiling” on page 38. We recommend

using an authorized ceiling mount.

• Position the projector the desired distance from the screen. The distance

from the lens of the projector to the screen, the zoom setting, and the

video format determine the size of the projected image. The top illus-

tration to the right shows three projected image sizes. For more infor-

mation about image sizes at different distances, see “Projected Image

Size” on page 43.

• The image offset is 127.3% when the projector is in 16:9 mode. This

means that if you have an image 10’ high, the bottom of the image will

be 2.73’ above the center of the lens.

• See “Connecting a video device” on page 15 for additional information

on 16:9 mode.

3.3 ft.

12.5 ft.

5 ft.

5 ft.7.6 ft. 18.9 ft.

bottom of image

2.73 ft above center

10 ft high

image

Projection angle in 16:9 mode

lens center

of lens

SP4805-02_usrguide.fm Page 6 Friday, June 11, 2004 8:22 AM

7

Projector and Device Connector Guide

The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as com-

puters, standard VCRs, DVD players (progressive and interlaced), HDTV sources, TV and satellite tuners, camcorders, video games (progressive and inter-

laced), and laser disc players.

Computer connections

Computer connections involve attaching the VGA and USB ends of the provided computer cable to a computer and connecting the other end (M1 cable end)

to the Computer In input on the projector. The USB part of the computer cable allows you to advance slides in a PowerPoint™ presentation via a remote

control. See page 10 for computer/projector setup information.

Video connections

The first step for connecting video is deciding what type of output connector you want to connect to the projector. If there is more than one output, select the

one with the highest quality. The best quality ranking, with 1 being the highest and 3 being the lowest, is:

1component video (RCA)

2S-video

3audio/visual composite video (RCA)

If your video device has a VGA connector, you can use the DVI connector on the back of the projector for very high quality.

S-video

projector input connectors

composite audio/visual (RCA)

12 volt audio out

DC output component (RCA)

DVI (M1-DA)

SP4805-02_usrguide.fm Page 7 Friday, June 11, 2004 8:22 AM

8

Video Device Video

Compatibility

If Your Device

Connector Is

Attach to Adapter

or Labeled

Connector on

Projector

For Setup Instructions, see Comments

Standard Broadcast TV (not

HDTV) via: cable, digital

cable, satellite TV, DVD, or

VCR

NTSC, PAL, and

SECAM formats

Component 480i

Composite video

or S-video

Component Video

Composite video

or S-video

Component Video

Composite (RCA) video connec-

tion on page 16.

Component on page 17.

Not for progressive

(i.e. HDTV) sources.

See page 9.

Standard Video Camera NTSC, PAL, and

SECAM formats

Component 480i

Composite video

or S-video

Component Video

Composite video

or S-video

Component Video

Composite (RCA) video connec-

tion on page 16.

Component on page 17.

Not for progressive

(i.e. HDTV) sources.

See page 9.

Standard Video Game NTSC, PAL, and

SECAM formats

Component 480i

Composite video

or S-video

Component Video

Composite video

or S-video

Component Video

Composite (RCA) video connec-

tion on page 16.

Component on page 17.

Not for progressive

(i.e. HDTV) sources.

See page 9.

SP4805-02_usrguide.fm Page 8 Friday, June 11, 2004 8:22 AM

9

Video Device Video

Compatibility

If Your Device

Connector Is

Attach to Adapter

or Labeled

Connector on

Projector

For Setup Instructions, see Comments

HDTV

(High Definition TV) 1035i, 1080i, 720p

Component 480i,

480p, 576i, 576p

DVI

Component video

Computer In (DVI)

Video 1 (component

RCA)

DVI connection on page 17

Component on page 17

Progressive DVD 1035i, 1080i, 720p

Component 480i,

480p, 576i, 576p

DVI

Component video

Computer In (DVI)

Video 1 (component

RCA)

DVI connection on page 17

Component on page 17

Progressive Video Game 1035i, 1080i, 720p

Component 480i,

480p, 576i, 576p

DVI

Component video

Computer In (DVI)

Video 1 (component

RCA)

DVI connection on page 17

Component on page 17

SP4805-02_usrguide.fm Page 9 Friday, June 11, 2004 8:22 AM

10

Connecting a computer source

Required computer connections

Connect one end of the provided computer cable (see page 15 for connect-

ing video devices) to the blue DVI Computer In connector on the projector.

Connect the other ends (USB and VESA) to the USB and VGA ports on your

computer. If you are using a desktop computer, you will need to disconnect

the monitor cable from the computer’s video port first.

This connection allows you to advance slides in a PowerPoint presentation

using the remote. USB drivers must be installed to use the USB feature.

For more information, see page 14.

Connect the black power cord to the Power connector on the side of the pro-

jector and to your electrical outlet.

NOTE: Always use the power cord that shipped with the projector.

Optional computer connections

To have sound with your presentation, connect an audio cable (not

included) to your computer and to the red and/or white Audio In connec-

tors on the projector.

connect computer cable

11

Displaying a computer source image

Remove the lens cap.

Toggle the Power switch on the side of the projector to the On position.

The LED flashes green and the fans start to run. When the lamp comes on,

the start up screen displays and the LED is steady green. It can take a

minute for the image to achieve full brightness.

? No start up screen? Get help on page 20.

Turn on your computer.

The computer’s image should appear on the projection screen. If it doesn’t,

press the Computer button on the projector’s keypad.

If your computer has Windows 98 as its operating system, see “Using the

projector with Windows 98 for the first time” on page 13 regarding the

driver setup process.

Make sure your laptop’s external video port is active.

Many laptops do not automatically turn on their external video port when a

projector is connected. Usually a key combination like FN + F8 or CRT/LCD

key turns the external display on and off. Locate a function key labeled

CRT/LCD or a function key with a monitor symbol. Press FN and the

labeled function key simultaneously. Refer to your laptop’s documenta-

tion to learn your laptop’s key combination.

? No laptop image? Try pressing the Auto Image button on the key-

pad. Get help on page 21.

remove lens cap

toggle Power switch

turn on computer

activate laptop’s external port

FN key

monitor key

or LCD/CRT key

SP4805-02_usrguide.fm Page 11 Friday, June 11, 2004 8:22 AM

12

Adjusting the image

If necessary, adjust the height of the projector by pressing the release button

to extend the foot.

If necessary, rotate the leveling foot located at the rear of the projector.

Avoid placing your hands near the hot exhaust vent in front of the projector.

Position the projector the desired distance from the screen at a 90 degree

angle to the screen.

See page 43 for a table listing screen sizes and distances.

Adjust the zoom or focus.

If the image is not square, adjust the keystone using the buttons on the key-

pad.

Press the top Keystone button to reduce the upper part of the image, and

press the bottom Keystone button to reduce the lower part.

Adjust the Contrast or Brightness in the Picture menu.

See page 33 for help with these menu adjustments.

adjust height

elevator

foot

rotate

leveling

foot

release button

13

Using the projector with Windows 98 for the first

time

The first time you connect a computer running Windows 98 to the projector,

the computer recognizes the projector as “new hardware” and the Add

New Hardware Wizard appears. Follow these instructions to use the Wiz-

ard to load the correct driver (which was installed with your Windows

operating system).

If you are running Windows 2000 or Windows ME, skip these steps and go

to “Adjusting the image” on page 12.

aClick Next to begin searching for the driver.

bMake sure “Search for the best driver” is selected, then click Next.

cUncheck any checked boxes, then click Next. Windows automatically

locates the driver. If this driver has been removed, reload the driver using

your Windows operating system CD.

dWhen Windows finds the driver, you are ready to install it. Click Next.

a

b

c

d

SP4805-02_usrguide.fm Page 13 Friday, June 11, 2004 8:22 AM

14

Skip this page if you did not connect a USB mouse cable

For Windows 98:

• If you connected the USB cable, the Add New Hardware Wizard

appears again. Drivers must be installed to use the USB functionality.

•The Wizard launches three times.

The first time it detects a USB Composite Device.

The second time a USB Human Interface Device (for the keyboard).

The third time it detects a USB Human Interface Device (for the

mouse).

For Windows 2000, Windows ME, and Windows XP:

• The USB drivers are automatically installed.

SP4805-02_usrguide.fm Page 14 Friday, June 11, 2004 8:22 AM

15

Connecting a video device

You can connect video devices such as VCRs, DVD players, camcorders,

digital cameras, video game consoles, HDTV receivers, and TV tuners to the

projector. There is also an audio input via the red and white A/V connec-

tors. You can connect the audio directly to the projector to get sound from

the built-in speaker, or you can connect the audio to your stereo system via

the Audio Out connector.

You can connect the projector to most video devices that can output video.

You cannot directly connect the coaxial cable that enters your house from a

cable or satellite company, the signal must pass through a tuner first. Exam-

ples of tuners are digital cable boxes, VCRs, digital video recorders, and sat-

ellite TV boxes. Basically, any device that can change channels is considered

a tuner.

Before connecting your projector, you should decide which aspect ratio you

want to use. The projector’s Aspect Ratio setting is accessed through the

projector’s Picture Menu. See page 33 for more information.

What is Aspect Ratio?

Aspect ratio is the ratio of the image width to image height. HDTV and

most DVDs are 16:9, which is the default for this projector. This projector is

not intended for use with 4:3 screens. When in 4:3 mode the projector places

black bars on both sides of the image. Native mode centers the image and

turns off the internal scaler so that any resolution larger than 854x480 is

cropped on the edges.

If you are projecting onto a screen, the size/shape of the screen may deter-

mine which aspect ratio to use. If you are projecting onto a blank wall, you

don’t have the screen size restriction. What you plan to project will also help

you choose between 4:3 and 16:9. For example, most TV shows are 4:3,

while most movies are 16:9. If you have a 16:9 screen, then you should select

an aspect ratio of 16:9 for anamorphic movies and HDTV, and Native for 4:3

content. If you have a 4:3 screen you should still use 16:9 for anamorphic

movies or HDTV, but you also have the option of using either 4:3 or Native

for 4:3 content. Keep in mind that anamorphic movies only appear correctly

if the DVD player is set to output to a 16:9 television.

16

16

99

16:9 image input 16:9 image

16:9

aspect ratio

16

9

4

3

4:3 image input 4:3 image on 16:9 screen

black bars

black bars

4:3 aspect ratio

4:3 image on 16:9 screen

Native

aspect ratio

4:3 image input

3

16

9

4

SP4805-02_usrguide.fm Page 15 Friday, June 11, 2004 8:22 AM

16

Video device connections

Composite (RCA) video connection

Plug the provided composite A/V cable’s yellow connector into the video-

out connector on the video device. Plug the other yellow connector into the

yellow Video 2 connector on the projector.

Plug a white connector into the left audio out connector on the video device

and plug a red connector into the right audio out connector on the video

device. Plug the remaining white connector into the white audio in connec-

tor on the projector, and plug the remaining red connector into the red

audio in connector on the projector.

Keep in mind that video output from composite connections are not as high

quality as S-video or component video.

S-video connection

If your video device uses a round, seven-prong S-video connector, plug an

S-video cable into the S-video connector on your video device and into the

S-video connector on the projector. Use the A/V cable’s red and white

audio connectors as described directly above (the yellow connectors on the

A/V cable are not used).

Keep in mind that S-video delivers higher quality video output than com-

posite, but not as high as component video.

connect A/V cable

17

Component (RCA) connection

To connect a progressive scan DVD or HD source, use the component con-

nector. Connect a component video cable with red, green, and blue RCA

connectors into the source device’s component connector. Connect the other

three end of the component cable into the Component Video connector on

the projector.

Use the composite A/V cable’s red and white audio connectors as described

on the previous page (the yellow connectors on the A/V cable are not used).

Keep in mind that component video delivers higher quality video output

than s-video or composite video.

DVI connection

If your video device uses a DVI connector, plug the DVI end of the M1-DA

cable into the video-out connector on the video device. This connector may

be labeled “To Monitor” on the video source. Plug the M1 computer end of

the cable into the Computer In connector on the projector. Do not plug the

USB end of this cable into the video device.

Use the composite A/V cable’s red and white audio connectors as described

on the previous page (the yellow connectors on the A/V cable are not used).

Keep in mind that DVI video delivers the highest quality video output.

Connect the power cord to the Power connector on the side of the projector

and to your electrical outlet.

NOTE: Always use the power cord that shipped with the projector.

connect component

composite audio cables

connect DVI and

composite audio cables

connect power cable

SP4805-02_usrguide.fm Page 17 Friday, June 11, 2004 8:22 AM

18

Displaying video

Remove the lens cap.

Toggle the Power switch on the side of the projector to the On position.

The LED flashes green and the fans start to run. When the lamp comes on,

the start-up screen is displayed and the LED is steady green. It can take a

minute for the image to achieve full brightness.

? No start up screen? Get help on page 21.

Plug in and turn on your video device.

The video device’s image should appear on the projection screen. If it

doesn’t, press the Video button on the keypad.

? No image? Try pressing the Source or Auto Image Get help on

page 21.

Adjusting the image

Adjust the height of the projector by pressing the release button to extend

the foot.

Rotate the leveling foot at the rear of the projector, if necessary.

Position the projector the desired distance from the screen at a 90 degree

angle to the screen.

See page 43 for a table listing screen sizes and distances to the screen.

remove lens cap

toggle Power switch

turn on video device

adjust height

elevator

foot

rotate

leveling

foot

release button

adjust distance

SP4805-02_usrguide.fm Page 18 Friday, June 11, 2004 8:22 AM

19

Adjust the zoom and focus.

If the image is not square, adjust the keystone using the buttons on the key-

pad. Press the top Keystone button to reduce the upper part of the image,

and press the bottom Keystone button to reduce the lower part.

Adjust the volume on the keypad or remote.

Adjust the Contrast, Brightness, Color, Tint, or Aspect Ratio in the Picture

menu. See page 33 for help with the menus and these adjustments.

For Aspect Ratio, keep in mind that DVD players must be configured for

16:9 in order to view the highest quality image. For more information

regarding Aspect Ratio, see page 15.

adjust zoom and focus

focus

(thin ring) (thick ring)

zoom

20

Shutting down the projector

The projector automatically displays a black screen after no active source is

detected for 30 minutes. This black screen helps preserve the life of the pro-

jector. The image returns when an active source is detected or a remote or

keypad button is pressed.

Screen Save

You can make the black screen appear after a preset number of minutes by

turning on the Screen Save feature in the Settings>System menu. See

page 38.

Power Save

The projector also has a Power Save feature that automatically turns the

lamp off after no active sources are detected and no user interaction with

the projector is performed for 20 minutes. By default, this feature is off. See

page 38.

Turning off the projector

You can turn the projector off simply by toggling the power switch to the off

position.

You can also press the remote’s Power button to place the projector in the

Off state while it is running. When the Power button is pressed twice (once

to start the power-down process and a second time to verify that you want

to power the projector off), the lamp turns off and the LED blinks green for

one (1) minute while the fans continue to run to cool the lamp. While the

LED is blinking green, the projector does not accept any keypad and remote

control input.

When the lamp has cooled, the LED lights solid green and the fans slow

down to minimal speed. To turn off the projector, toggle the power switch to

the off position.

NOTE: Once the projector has been toggled off, you must wait for one (1)

minute before turning the projector on again. This allows the lamp to prop-

erly cool. However, if the remote was used to power the projector to the Off

state you do not need to wait one minute to turn it on again.

Troubleshooting your setup

If your image appears correctly on the screen, skip to the next section. If it

does not, troubleshoot the setup.

The LED on top of the projector indicates the state of the projector and can

help you troubleshoot.

The following tables show common problems. In some cases, more than one

possible solution is provided. Try the solutions in the order they are pre-

21

Problem Solution Result

no start up screen plug power cord in projector’s left side

remove lens cap

toggle power switch

correct image

only start up screen appears press the Computer button

activate laptop’s external port

computer image projected

22

Problem Solution Result

no computer image, just the words “Signal out of

range”

press the Auto Image button on keypad computer image projected

A

Signal out of

range

Panel>Display>Settings>Advanced>Adapter

(location varies by operating system)

you may also need to set a different

resolution on your computer, as shown

in the following problem, “image fuzzy

or cropped”

adjust computer refresh rate in Control

A

A

SP4805-02_usrguide.fm Page 22 Friday, June 11, 2004 8:22 AM

23

Problem Solution Result

image fuzzy or cropped set your computer’s display resolution to

the native resolution of the projector

(Start>Settings>Control

Panel>Display>Settings tab)

select 854x480

image clear and not cropped

image not centered on screen

move projector, adjust zoom, adjust height

correct image

A

AA

For a laptop,

disable laptop

monitor

or turn-on dual-

display mode

A

adjust horizontal or

Picture>Advanced

vertical position in

menu

SP4805-02_usrguide.fm Page 23 Friday, June 11, 2004 8:22 AM

24

Problem Solution Result

image not square adjust Keystone on keypad square image

image not sharp adjust Sharpness (video sources only) in the

Picture>Advanced menu

correct image

ABAB AB

SP4805-02_usrguide.fm Page 24 Friday, June 11, 2004 8:22 AM

25

Problem Solution Result

image upside down turn off ceiling in Settings>System menu correct image

image reversed left to right turn off rear in Settings>System menu correct image

projected colors don’t match source

adjust color, tint, color temperature,

brightness, contrast in the menus correct image

AB

AB

AAB

COLOR COLOR

SP4805-02_usrguide.fm Page 25 Friday, June 11, 2004 8:22 AM

26

Problem Solution Result

The video embedded in my PowerPoint

presentation does not play on the screen

Turn off the internal LCD display on your

laptop Embedded video plays correctly

lamp won’t turn on, LED blinking red

make sure vents aren’t blocked, turn off the

projector and allow it to cool for one

minute lamp turns on

A

A

B

A

B

LED

Startup

Screen

SP4805-02_usrguide.fm Page 26 Friday, June 11, 2004 8:22 AM

27

Still need assistance?

If you need assistance, visit our website or call us. See the inside of the back

cover for support contact information. This product is backed by a limited

warranty. An extended warranty plan may be purchased from your dealer.

When sending the projector in for repair, we recommend shipping the unit

in its original packing material, or having a professional packaging com-

pany pack the unit. Please insure your shipment for its full value.

Problem Solution Result

“Change lamp” message appears at startup or lamp

won’t turn on and LED blinking red

lamp must be replaced (see page 40) lamp turns on

LED

replace lamp

Startup

Screen

SP4805-02_usrguide.fm Page 27 Friday, June 11, 2004 8:22 AM

28

Using the remote control

The remote uses two (2) provided AAA batteries. They are easily installed

by sliding the cover off the remote’s back, aligning the + and - ends of the

batteries, sliding them into place, and then replacing the cover.

To operate, point the remote at the projection screen or at the projector (not

at the video device or computer). The range of optimum operation is up to

30 feet (9.14m).

Press the remote’s Menu button to open the projector’s menu system. Use

the arrow buttons to navigate, and the Select button to select features and

adjust values in the menus. See page 32 for more info on the menus.

The remote also has:

•Power button to turn the projector on and off (see page 20 for shut-

down info)

• backlight button to light the remote’s buttons in the dark

•Brightness and Contrast buttons to adjust the image

•Blank button to display a blank screen instead of the current image (to

change the color of the screen, see page 39)

•Source buttons to switch among sources (to assign a particular source

to a source button, see page 38) and a source toggle

•Resize button to change the Aspect Ratio (see page 33)

•Auto Image button to resynch the projector to the source

•Preset button to restore stored settings (see page 34)

•Overscan button to remove noise in a video image (page 37)

Troubleshooting the remote

• Make sure the batteries are installed in the proper orientation and are

not dead.

• Make sure you’re pointing the remote at the projector or the screen, not

at the video device or the computer, and are within the remote range of

30 feet (9.14m).

backlight button

navigation buttons

SP4805-02_usrguide.fm Page 28 Friday, June 11, 2004 8:22 AM

29

Using the audio

Using the projector’s speakers

To use the projector’s speaker, connect your source to the Audio In connec-

tors (L and/or R) on the projector’s composite connectors.

To adjust the volume, press the Vol um e buttons on the keypad or remote.

To mute the sound, press the Mute button on the remote.

Troubleshooting Audio

If you aren’t hearing the audio, check the following:

• Make sure the audio cable is connected.

• Make sure mute is not active (press the Mute button on the remote).

• Make sure the volume is turned up enough. Press the Volume button

on the keypad or remote.

• Make sure the correct source is active.

• Adjust the audio source.

• If playing a video, make sure the playback has not been paused.

Connecting external speakers

The projector can be attached to external speakers that have their own

power source by plugging a speaker cable (not included) into the projector’s

Audio Out connector.

connect audio cable

adjust volume

external speakers

speaker

cable

audio out

with own power source

SP4805-02_usrguide.fm Page 29 Friday, June 11, 2004 8:22 AM

30

Using the keypad buttons

Most buttons are described in detail in other sections, but here is an over-

view of their functions:

Menu–opens the on-screen menus (page 32).

Select–confirms choices made in the menus (page 32).

Up/Down arrows–navigates to and adjusts settings in the menus (page 32).

Auto Image–resets the projector to the source.

Presets–cycles through the available preset settings (page 34).

Keystone–adjusts squareness of the image (page 12).

Volume –adjusts sound (page 29).

Video and Computer–changes the active source.

menu navigation

buttons

SP4805-02_usrguide.fm Page 30 Friday, June 11, 2004 8:22 AM

31

Optimizing computer images

After your computer is connected properly and the computer’s image is on

the screen, you can optimize the image using the onscreen menus. For gen-

eral information on using the menus, see page 32.

• Adjust the Keystone, Contrast, or Brightness in the Picture menu

(page 33).

• Change the Aspect Ratio. Choose the option that best fits your input

source (page 33).

• Adjust the Color Temperature in the Advanced menu (page 35).

• Adjust the Phase, Tracking, or Horizontal or Vertical position in the

Advanced menu (page 37).

• Once you have optimized the image for a particular source, you can

save the settings using Presets. This allows you to quickly recall these

settings later (page 34).

Optimizing video images

After your video device is connected properly and the image is on the

screen, you can optimize the image using the onscreen menus. For general

information on using the menus, see page 32.

• Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture

menu (page 33).

• Select a Sharpness setting (page 35).

• Use the Color Control to adjust the color gain (page 36).

• Adjust the Color Temperature. Select a listed value (page 36).

• Turn on Overscan to remove noise on the edges of the video image

(page 37).

• Change the Aspect ratio (page 33). Aspect ratio is the ratio of the image

width to image height. TV screens are usually 1.33:1, also known as 4:3.

HDTV and most DVDs are 1.78:1, or 16:9 (the projector’s default).

Choose the option that best fits your input source in the menus, or

press the Resize button on the remote to cycle through the options. See

page 28.

• Select a specific Color Space. See page 36.

• Select a different Video Standard. Auto tries to determine the standard

of the incoming video. Select a different standard if necessary. See

page 37.

• Make sure your DVD player is set for a 16:9 television. See your DVD

player’s user’s guide for instructions.

Customizing the projector

You can customize the projector for your specific setup and needs. See

page 38 to page 40 for details on these features.

• For rear projection, turn rear mode on in the Settings>System menu.

• For ceiling mounted projection, turn ceiling mode on in the Set-

tings>System menu.

• Specify which source the projector checks first for active video during

power-up.

• Turn the projector’s display messages on and off.

• Turn on power saving features.

• Specify blank screen colors and start up logos.

• Specify the language viewed on the menus.

• Save settings for the active source as a preset.

SP4805-02_usrguide.fm Page 31 Friday, June 11, 2004 8:22 AM

32

Using the menus

To open the menus, press the Menu button on the keypad or remote. (The

menus automatically close after 60 seconds if no buttons are pressed.) The

Main menu appears. Use the arrow buttons to move up and down to high-

light the desired submenu, then press the Select button.

To change a menu setting, highlight it, press Select, then use the up and

down arrow buttons to adjust the value, select an option using radio but-

tons, or turn the feature on or off using check boxes. Press Select to confirm

your changes. Use the arrows to navigate to another setting. When your

adjustments are complete, navigate to Previous or Exit, then press Select to

go to the previous menu; press the Menu button at any time to close the

menus.

Dots appears before the menu name. The number of dots indicate menu’s

level, ranging from one (the Main menu) to four (the most nested menus).

The menus are grouped by usage:

• The Picture menu provides image adjustments.

• The Settings menu provides set-up type adjustments that are not

changed often.

• The About menu provides a read-only display of information about the

projector and source.

Certain menu items may not be visible or may be grayed depending upon a

particular source being connected. For example, Sharpness is only available

for video sources and is not visible when a computer source is active. Menu

options are grayed out only if the source if selected but no signal is present.

For example, if the projector is set to a video source but the source, such as a

DVD player, is turned off video menu options are grayed out.

keypad navigation

Main menu buttons

dots

Picture Settings

menu

menu

About menu

SP4805-02_usrguide.fm Page 32 Friday, June 11, 2004 8:22 AM

33

Picture menu

To adjust the following settings, highlight the setting, press Select, use the

up and down arrows to adjust the values, then press Select to confirm the

changes.

Keystone: adjusts the image vertically and makes a squarer image. You can

also adjust keystone from the keypad.

Contrast: controls the degree of difference between the lightest and darkest

parts of the picture and changes the amount of black and white in the

image.

Brightness: changes the intensity of the image.

Color: adjusts a video image from black and white to fully saturated color.

The color setting applies to video sources only.

Tint: adjusts the red-green color balance in the image of NTSC video

images. The tint setting applies to NTSC video sources only.

Aspect Ratio: Aspect ratio is the ratio of the image width to image height.

TV screens are usually 4:3. HDTV and most DVDs are 16:9. The projector’s

default is 16:9. See “What is Aspect Ratio?” on page 15for more information.

Select Native to see the unmodified input with no resizing by the projector.

Select 16:9 to watch enhanced widescreen DVDs. Select Letterbox: to pre-

serve the 16:9 aspect ratio. If you have a 16:9 source and screen, the image

fills the screen. If your source is letterboxed, the image is expanded to fill

the screen.

For more information regarding Aspect Ratio, see page 15.

Picture menu

increasing keystone decreasing keystone

Aspect ratio

SP4805-02_usrguide.fm Page 33 Friday, June 11, 2004 8:22 AM

34

Presets: This allows you to customize settings and save the settings to be

restored later. To restore the factory default settings, choose Factory Reset in

the Settings>Service menu.

To set a preset for the current source, adjust the image, select Save Settings

in the Presets menu, then choose Save User 1, 2, or 3. You can recall these

settings in the future by selecting the appropriate user presets.

Gamma: Gamma tables contain preset intensity configurations optimized

for the input source. You can select a gamma table that has been specifically

tuned for either film, CRT (Cathode Ray Tube), video, Bright Room, or PC

input. (Film input is material originally captured on a film camera, like a

movie; video input is material originally captured on a video camera, like a

TV show or sporting event.) White Peaking increases the brightness of

whites that are near 100%.

NOTE: Your viewing preferences may vary. Cycle through the gamma

options and pick the one you like the best.

Presets

Save

User

Settings

SP4805-02_usrguide.fm Page 34 Friday, June 11, 2004 8:22 AM

35

Advanced menu

Chroma Detail: This adjusts the color sharpness.

Luma Detail: This adjusts the overall sharpness (edge enhancement) of the

Luma signal.

Noise Reduction: adjusts signal noise reduction. Choose Off to have no

noise reduction, choose Auto to have the software determine the amount of

noise reduction, or choose Manual and adjust the Level.

CCS: (Cross Color Suppression) processes the signal to remove any color

information from the luma portion of the signal. It is On for all composite

signals, and can be turned off for S-video and interlaced component signals.

Sharpness: (video sources only) changes the clarity of the edges of a video

image. Select a sharpness setting.

Advanced menu

Noise Reduction

Sharpness

SP4805-02_usrguide.fm Page 35 Friday, June 11, 2004 8:22 AM

36

Color Space: This option applies to computer and component video

sources. It allows you to select a color space that has been specifically tuned

for the input signal. When Auto is selected, the projector automatically

determines the standard. To choose a different setting, turn off Auto, then

choose RGB for computer sources, choose either REC709 or REC601 for

component video sources.

Color Temperature: changes the intensity of the colors. Select a value.

Color Control: allows you to individually adjust the gain (relative warmth

of the color) of the red, green, and blue colors.

Color Space

Color

Temperature

Color Control

SP4805-02_usrguide.fm Page 36 Friday, June 11, 2004 8:22 AM

37

Video Standard: when it is set to Auto, the projector attempts to automati-

cally pick the video standard based on the input signal it receives. (The

video standard options may vary depending on your region of the world.) If

the projector is unable to detect the correct standard, the colors may not

look right or the image may appear “torn.” If this happens, manually select

a video standard by selecting NTSC, PAL, or SECAM from the Video Stan-

dard menu.

Overscan: (video sources only) removes noise around the video image.

Sync Threshold Adjust: If a hardware device, such as a DVD player, is not

syncing properly with the projector, select this option to help it to sync

when connected to the projector.

The following four (4) options are for computer sources only.

Phase: adjusts the horizontal phase of a computer source.

Tr a c k i n g : adjusts the vertical scan of a computer source.

Horizontal/Vertical Position: adjusts the position of a computer source.

Video Standard

SP4805-02_usrguide.fm Page 37 Friday, June 11, 2004 8:22 AM

38

Settings menu

Audio: allows adjustments to Volume of the internal speaker and allows a

chime to play when starting the projector. Adjustments can also be made

from the projector’s keypad and the remote.

Sources: determines which source the projector checks first for active video

during power-up. When Autosource is selected, the Source Enable feature

indicates which sources the projector attempts to lock onto. You can use the

Source Enable feature to eliminate certain sources from this search, which

will speed the search. The source options are Computer for a computer,

progressive DVD, or HDTV source, Video 1 for S-video connections, Video

2 for component video connections and Video 3 for composite video

sources. By default, the check boxes for all sources are checked. Uncheck a

source box to eliminate it from the search. When Autosource is not checked,

the projector defaults to the source selected in Sources. To display another

source, you must manually select one by pressing the Computer or Video

button on the remote or keypad.

System>Rear: reverses the image so you can project from behind a translu-

cent screen. Ceiling: turns the image upside down for ceiling-mounted pro-

jection. Low Power: toggles between on and off. Turn it on to lower the light

output of the lamp. This also lowers the fan speed, making the projector

quieter. Display Messages: displays status messages (such as “Searching” or

“Mute”) in the lower-left corner of the screen.Tr a ns l u c e n t O S D : makes the

menus translucent. This prevents the image from being completely covered

by the menus while you are making image adjustments. Screen Saver Off:

prevents the screensaver on your computer from being activated if the USB

portion of the M1 is plugged into the computer. This function was previ-

ously called NND. Screen Trigger: turns on the 12 volt DC output switch

on the connector panel. Power Save: automatically turns the lamp off after

no signals are detected for 20 minutes. After 10 additional minutes with no

signal, the projector powers down. If an active signal is received before the

projector powers down, the image will be displayed. After an additional 10

minutes with no signal, the projector powers down and can be toggled off.

If an active signal is received before the projector powers down, the image

will be displayed.

Settings menu

Audio

Sources

Source

Enable

System menu

SP4805-02_usrguide.fm Page 38 Friday, June 11, 2004 8:22 AM

39

Startup Logo: allows you to display a blank screen instead of the default

screen at startup, and when no source is detected.

Blank Screen: determines what color is displayed when you press the

Blank button on the remote.

Language: allows you to select a language for the onscreen display.

Service: To use these features, highlight them and press Select.

Factory Reset: restores all settings to their default.

Lamp Reset: resets the lamp hours used counter in the About menu to

zero. Do this only after changing the lamp.

Service Code: only used by authorized service personnel.

About: provides information about the projector and the active source.

Startup Logo

Blank Screen

Language menu

Service menu

About menu

SP4805-02_usrguide.fm Page 39 Friday, June 11, 2004 8:22 AM

40

Maintenance

Cleaning the Lens

1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

• Avoid using an excessive amount of cleaner, and don’t apply the

cleaner directly to the lens. Abrasive cleaners, solvents or other harsh

chemicals might scratch the lens.

2Lightly wipe the cleaning cloth over the lens in a circular motion. If you

don’t intend to use the projector immediately, replace the lens cap.

Replacing the Projection Lamp

The lamp hours used timer in the About menu counts the number of hours

the lamp has been in use. Twenty hours before the lamp life expires, the

message “Change lamp” appears on the screen at startup. If the maximum

lamp time is exceeded, the lamp will not light. In this case, after replacing

the lamp you must reset the lamp hours by simultaneously pressing both

Volume buttons on the keypad and holding them for 10 seconds.

NOTE: You can order new lamp housings from your dealer. See the Packing

list for information. Use only a replacement lamp with the same type and

rating as the original lamp.

1Turn off the projector and unplug the power cord.

2Wait 30 minutes to allow the projector to cool thoroughly.

3Turn the projector on its side so that the lamp door is facing you. Using a

flat-blade screwdriver, gently pry the lamp door from the projector by

placing the screwdriver blade into the space between the top of the lamp

door and the projector.

Lamp hours used

wait 30 minutes

turn off and unplug

projector

lamp door

SP4805-02_usrguide.fm Page 40 Friday, June 11, 2004 8:22 AM

41

4Loosen the two captive screws that attach the lamp housing to the pro-

jector.

5Detach the lamp connector from the projector by depressing the locking

tab on the connector and lightly pulling it free.

WARNING:

To avoid burns, allow the projector to cool for at least 30 minutes

before you replace the lamp.

Do not drop the lamp housing or touch the glass bulb! The glass

may shatter and cause injury.

Be extremely careful when removing the lamp housing. In the

unlikely event that the bulb ruptures, small glass fragments may be

generated. The lamp housing is designed to contain these frag-

ments, but use caution when removing the lamp housing. Before

replacing the lamp, clean the lamp compartment and dispose of

cleaning materials. Wash hands after lamp replacement. This prod-

uct has a lamp which contains a very small amount of mercury. Dis-

pose of it as required by local, state or federal ordinances and

regulations. For more information see www.eiae.org.

6Carefully remove the lamp housing. Dispose of the lamp in an environ-

mentally proper manner.

7Install the new lamp housing and tighten the screws.

8Re-attach the lamp connector to the projector. The locking tab should

engage when the connector is fully plugged in.

9Replace the lamp door.

10 Plug in the power cord and toggle the Power switch to turn the projector

back on.

11 To reset the lamp hour timer, navigate to the Settings>Service menu

and select Lamp Reset. See page 40 for details.

42

Cleaning the Lamp Housing Screens

In dirty or dusty environments, the two dust filter screens in the lamp hous-

ing can become clogged, causing high temperatures and premature lamp

failure. Routine maintenance to remove dust from the screens lowers the

lamp operating temperature and prolongs lamp life. To maximize lamp life

you should clean the screen at least every 250 hours depending upon envi-

ronmental conditions. The dirtier or dustier the environment, the more

often you should clean the screens.

1Remove the lamp housing.

2Examine the dust filter screens on the lamp housing. If necessary, use a

vacuum cleaner set on low power to clean the screens. Be careful not to

disturb any internal components when cleaning the screens.

3Replace the lamp housing and lamp door.

Using the security lock

The projector has a security lock for use with a PC Guardian Cable Lock

System. Refer to the information that came with the lock for instructions on

how to use it.

lamp housing

lamp two screens

(one on each

side of the

lamp housing)

security

lock

SP4805-02_usrguide.fm Page 42 Friday, June 11, 2004 8:22 AM

43

Appendix

Projected Image Size

NOTE: Visit our website for an interactive image size calculator.

Tab le 2 :

Range of distance to the screen for a given screen size for the projector

Diagonal

Screen Size

(inches/m)

Projection Ratio Distance to screen

Image Width

(inches/m)

Wide Zoom

Position (0.66)

Telephoto Zoom

Position (0.55) Distance (feet/m)

Maximum

distance

(feet/m)

Minimum

Distance

(feet/m)

40/1.02 34.86/0.89 0.66 5.05/1.54 6.06/1.85 5.05/1.54

40/1.02 34.86/0.89 0.55 6.06/1.85

50/1.27 43.58/1.11 0.66 6.31/1.92 7.58/2.31 6.31/1.92

50/1.27 43.58/1.11 0.55 7.58/2.31

60/1.52 52.291.33 0.66 7.58/2.31 9.09/2.77 7.58/2.31

60/1.52 52.291.33 0.55 9.09/2.77

100/2.54 87.16/2.21 0.66 12.63/3.85 15.15/4.62 12.63/3.85

100/2.54 87.16/2.21 0.55 15.15/4.62

150/3.81 130.74/3.32 0.66 18.94/5.77 22.73/6.93 18.94/5.77

150/3.81 130.74/3.32 0.55 22.73/6.93

200/5.08 174.32/4.43 0.66 25.25/7.70 30.30/9.24 25.25/7.70

200/5.08 174.32/4.43 0.55 30.30/9.24

SP4805-02_usrguide.fm Page 43 Friday, June 11, 2004 8:22 AM

44

Red LED Behavior and Projector Errors

If the projector is not functioning properly and the LED is blinking red, con-

sult Ta b l e 3 to determine a possible cause. There are two-second pauses

between the blinking cycles. Visit our website for more details on the red

LED error codes.

Table 3:

Red LED Behavior Explanation

One (1) blink The lamp won't strike after five (5)

attempts. Check the lamp and lamp door

installations for loose connections.

Two (2) blinks The lamp counter hours have exceeded

lamp life hours. Replace the lamp and

reset the lamp hours counter.

Three (3) blinks The projector has shut down. Check to

see if the lamp door is open. If the lamp

door is closed, toggle off the projector

and wait one minute, then toggle the pro-

jector on again. If the lamp does not strike

after one minute, replace the lamp. Con-

tact Technical Support (see page 27) for

repair if replacing the lamp does not solve

the problem.

Four (4) blinks The fan has failed. Contact Technical Sup-

port (see page 27) for repair or replacing

the fan.

Five (5) blinks The projector is overheating. Check for a

blocked air vent (page 26) or clogged

lamp housing screen (page 42). Contact

Technical Support for repair if clearing the

vents/screens does not solve the problem.

SP4805-02_usrguide.fm Page 44 Friday, June 11, 2004 8:22 AM

45

INDEX

Numerics

16x9 31

16x9 vs 4x3 screen aspect 15

A

About 39

Advance menu 35

advancing slides 10

Aspect ratio 33

aspect ratio 15

Audio 38

Audio In connector 10, 16, 29

audio input 15

Audio Out 15

Autosource 38

B

Blank Screen 39

blinking green 20

blinking red 20

Brightness 33

C

cable box 15

CCS 35

Chroma Detail 35

Color 33

Color Control 36

Color Space 36

color suppression 35

Color Temperature 36

Computer In connector 10

connecting

video device 15

connector panel 5

connectors on projector 8, 9

contacting InFocus 27

Contrast 33

customer service contact information 27

customizing the projector 31

D

Display Messages 38

Drivers

USB 14

Windows 98 14

DVDs 33

DVI connector 17

F

Factory Reset 39

Faroudja video proecessing 35

focus 12, 19

H

HDTV 31, 33

Horizontal 37

SP4805-02_usrguide.fm Page 45 Friday, June 11, 2004 8:22 AM

46

I

image

size 6

image optimization 31

image size

projected 43

K

keypad buttons

projector 30

keystone adjustment 12, 19

L

Lamp Housing Screens

cleaning 42

lamp replacement 40

Lamp Reset 39

Language 39

LED 20

blinking green 20

solid green 20

LED Behavior

red 44

LED behavior 20

leveling foot 18

Low Power 38

Luma Detail 35

M

Macintosh computers

compatibility 4

maintaining the projector 40

Menu button 32

menu usage 32

Mute button 29

O

optimizing images 31

optimizing video 31

Overscan 37

P

Phase 37

Picture menu 33

Power connector 10

power cord 10, 17

Power Save 20, 38

Power switch 11

Presets 34

projection distance 6

projector

connecting video devices 15

connector panel 5

customization 31

keypad buttons 30

maintenance 40

positioning 6

remote control 28

setting up 6

troubleshooting problems 20

turning off 20

SP4805-02_usrguide.fm Page 46 Friday, June 11, 2004 8:22 AM

47

R

Rear 38

Red LED behavior 44

registering your projector 4

remote control 28

advancing slides 10

replacing the lamp 40

S

Screen Aspect 15

Screen Save 20

Screen Saver Off 38

security lock 42

Service 39

Service Code 39

Settings menu 38

sharpness 35

solid green 20

solid red 20

Sources 38

Startup Logo 39

S-video connector 16

Sync Threshhold Adjust 37

System 38

T

Tint 33

Tracking 37

troubleshooting 20

TrueLife settings 35

turning off

projector 20

TV tuner 15

U

USB, connecting 10

V

Vertical 37

video optimizing 31

video processing 35

Video Standard 37

volume adjustment 19

Volume button 29

W

Windows 2000 14

Windows 98 13

Windows ME 14

Windows XP 14

Z

zoom 12, 19

SP4805-02_usrguide.fm Page 47 Friday, June 11, 2004 8:22 AM

48

Limited Warranty

Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-

poration ("InFocus") warrants that the Projector, Lamps and Accessories

(hereinafter collectively or individually referred to as "Product" as appropri-

ate) purchased from InFocus, an InFocus distributor, or an InFocus reseller

will conform to InFocus' specifications and be free from defects in material

or workmanship for the respective Limited Warranty period provided

below. InFocus does not warrant that the Product will meet the specific

requirements of the end-user customer.

If the Product while subject to this Limited Warranty, is defective in material

or workmanship during the warranty period, then InFocus, at its option,

will REPAIR or REPLACE the Product.

All exchanged parts and Products replaced under this Limited Warranty

will become property of InFocus. InFocus' sole obligation is to supply (or

pay for) all labor necessary to repair the Product found to be defective

within the Limited Warranty period and to repair or replace defective parts

with new parts or, at the option of InFocus, serviceable used parts that are

equivalent or superior to new parts performance. Limited Warranty periods

are as follows:

•Projector Product Limited Warranty Period (Excluding Lamps): Two

(2) years from date of purchase.

•Lamp Product Limited Warranty Periods: From the date of Projector

Product purchase, the original installed lamp shall have a 90-day or 500

hours usage Limited Warranty Period, whichever comes first. Replace-

ment Lamps purchased at the time of Projector Product purchase will

have a 90-day or 500 hours usage Limited Warranty Period from the

date of installation, whichever comes first. Replacement lamps pur-

chased after the time of Projector Product purchase shall have a 90-day

or 500 hours usage Limited Warranty Period from the date of replace-

ment lamp purchase, whichever comes first.

•Accessory Product Limited Warranty Period: one (1) year from date of

purchase.

WARRANTY LIMITATION AND EXCLUSION

THIS WARRANTY SETS FORTH INFOCUS' MAXIMUM LIABILITY FOR

ITS PRODUCT. THIS WARRANTY EXTENDS ONLY TO PRODUCTS PUR-

CHASED FROM INFOCUS OR AN INFOCUS AUTHORIZED RESELLER.

InFocus shall have no further obligation under the foregoing Limited War-

ranty if the Product has been damaged due to abuse, misuse, neglect, smoke

exposure (cigarette or otherwise), accident, unusual physical or electrical

stress, unauthorized modifications (including use of an unauthorized

mount), tampering, alterations, or service other than by InFocus or its

authorized agents, causes other than from ordinary use or failure to prop-

erly use the Product in the application for which said Product was intended.

This Limited Warranty excludes Product cleaning, repair, or replacement of

plastics due to cosmetic damage and damage as a result of normal wear.

Product repair outside of the terms of the Limited Warranty will be on a

time and materials basis. Prolonged Product "demonstration" causes

unusual Product wear and is not considered normal use under the terms of

this Limited Warranty. The Accessory Product Limited Warranty covers the

accessory item only and excludes normal wear. The Lamp Product Limited

Warranty excludes expected lamp degradation.

Remanufactured Products and Software Products are exempt from the fore-

going Limited Warranty. Please refer to the appropriate Remanufactured

Product Limited Warranty or Software Product Limited Warranty for appli-

cable Warranty information.

DISCLAIMER OF UNSTATED WARRANTIES

THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLI-

CABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR

PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT

EXTEND BEYOND THE DISCRITPTION ON THE FACE HEREOF AND

THE FOREGOING WARRANTY SHALL NOT BE EXTENDED, ALTERED

OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY INFOCUS.

SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW

LONG AN IMPLIED WARRANTY MAY LAST, SO SUCH LIMITATIONS

MAY NOT APPLY TO YOU.

SP4805-02_usrguide.fm Page 48 Friday, June 11, 2004 8:22 AM

49

Limited Warranty Period

The Limited Warranty periods hereof commence on the date of purchase by

the end-user customer. These Limited Warranty provisions shall apply only

to the end-user purchaser (first person or entity that purchased a new Prod-

uct for personal or business use and not for the purpose of distribution or

resale). SOME JURISDICTIONS MAY GRANT YOU CONSUMER RIGHTS

WITH MINIMUM WARRANTY DURATION THAT DIFFER FROM THE

DURATIONS PROVIDED HEREIN, AND INFOCUS WILL HONOR ALL

SUCH CONSUMER RIGHTS.

To Be Eligible For Limited Warranty Coverage

Any person exercising a claim under this Limited Warranty must establish

to the satisfaction of InFocus both the date of purchase and that the Product

was purchased new. The sales receipt or invoice, showing the date of pur-

chase of the Product is the proof of the date of purchase.

To Obtain Warranty Service

During the Limited Warranty period, to exercise this Limited Warranty, the

purchaser must first contact 1) InFocus, 2) a service facility authorized by

InFocus or 3) the place of original purchase.

InFocus Customer Service - 1-800-799-9911 or techsupport@infocus.com

For Warranty service, the purchaser will be advised to return or deliver the

defective Product freight and all fees prepaid, to an InFocus Service Center

or to a service facility authorized by InFocus. When returning Product to

InFocus, a Return Material Authorization Number (RMA #) is required and

must be clearly displayed on the outside of the shipping carton or a similar

package affording an equal degree of protection. InFocus or the service

facility authorized by InFocus will return the repaired/replaced Product

freight prepaid to the purchaser.

Products returned for Warranty service must be accompanied by a written

letter that: (i) explains the problem; (ii) provides proof of date of purchase;

(iii) provides the dealer's name; and (iv) provides the model and serial num-

ber of the Product. Upon request of InFocus Corporation or an authorized

repair center for InFocus, proof of legal import must accompany the war-

ranty repair Product, otherwise the Product must be returned to the place of

original purchase, to the manufacturer (Purchaser must bear all tax, duty

and freight), or the Purchaser must bear charges for the warranty repair.

No repair or replacement of Product or part thereof shall extend the Limited

Warranty period as to the entire Product. Warranty on the repair part and

workmanship shall only be effective for a period of ninety (90) days follow-

ing the repair or replacement of that part or the remaining period of the

Product Limited Warranty whichever is greater.

LIMITATION OF LIABILITY

IT IS UNDERSTOOD AND AGREED THAT INFOCUS' LIABILITY

WHETHER IN CONTRACT, IN TORT, UNDER ANY WARRANTY, IN

NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF

THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND

UNDER NO CIRCUMSTANCES SHALL INFOCUS BE LIABLE FOR SPE-

CIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR

LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE PRICE

STATED FOR THE PRODUCTS IS A CONSIDERATION IN LIMITING

INFOCUS' LIABILITY.

Limitation on Bringing Action - No action, regardless of form, arising out

of the agreement to purchase the Product may be brought by purchaser

more than one year after the cause of action has accrued.

Governing Law - Any action, regardless of form, arising out of the agree-

ment to purchase the Product is governed by Oregon law.

Mandatory Arbitration - Any action, regardless of form, arising out of the

agreement to purchase the Product is subject to mandatory arbitration.

40

Maintenance

Cleaning the Lens

1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.

• Avoid using an excessive amount of cleaner, and don’t apply the

cleaner directly to the lens. Abrasive cleaners, solvents or other harsh

chemicals might scratch the lens.

2Lightly wipe the cleaning cloth over the lens in a circular motion. If you

don’t intend to use the projector immediately, replace the lens cap.

Replacing the Projection Lamp

The lamp hours used timer in the About menu counts the number of hours

the lamp has been in use. Twenty hours before the lamp life expires, the

message “Change lamp” appears on the screen at startup. If the maximum

lamp time is exceeded, the lamp will not light. In this case, after replacing

the lamp you must reset the lamp hours by simultaneously pressing both

Vol ume buttons on the keypad and holding them for 10 seconds.

NOTE: You can order new lamp housings from your dealer. See the Packing

list for information. Use only a replacement lamp with the same type and

rating as the original lamp.

1Turn off the projector and unplug the power cord.

2Wait 30 minutes to allow the projector to cool thoroughly.

3Turn the projector on its side so that the lamp door is facing you. Using a

flat-blade screwdriver, gently pry the lamp door from the projector by

placing the screwdriver blade into the space between the top of the lamp

door and the projector.

Lamp hours used

wait 30 minutes

turn off and unplug

projector

lamp door

41

4Loosen the two captive screws that attach the lamp housing to the pro-

jector.

5Detach the lamp connector from the projector by depressing the locking

tab on the connector and lightly pulling it free.

WARNING:

To avoid burns, allow the projector to cool for at least 30 minutes

before you replace the lamp.

Do not drop the lamp housing or touch the glass bulb! The glass

may shatter and cause injury.

Be extremely careful when removing the lamp housing. In the

unlikely event that the bulb ruptures, smataente sma b-15.4(031 e )]TJ0 -1.2.88 TD0.3116 Tc0.0217 Twgaw e mp6-1.soeieiawaweth-11.ese2( fg)14.7g

e5tdjto cst-3oooe3mimao th710.5(e(t)8.2(a9)8.5(mpe5)9.2(-3)1.us(t)-5.ima)-5.5(o)-7.gite3 for8