Infocus T146 Users Manual RG_INF_IN146

T146 to the manual 9c183ca7-6811-4250-8431-22178e68275a

2015-02-05

: Infocus Infocus-T146-Users-Manual-393607 infocus-t146-users-manual-393607 infocus pdf

Open the PDF directly: View PDF PDF.
Page Count: 36

Regulatory models: T146
IN146
010-0753-00
DISPERINDAG No. 0287/1.824.51/09.0
1
Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon
97223-8368 USA
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
ErP Directive 2009/125/EC
EMC Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
Safety: IEC 60950-1: 2005 (MOD)
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or registered
trademarks of Adobe Systems Incorporated. DLP®, DLP Link and the DLP logo are
registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas
Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or
trademarks of InFocus Corporation in the United States and other countries.
NOTE: This product is covered electrical and electronic equipment under
the European Union's Waste from Electrical and Electronic Equipment
("WEEE") Directive (2002/96/EC). The WEEE Directive requires that covered
equipment be collected and managed separately from typical household waste
in all EU member states. Please follow the guidance of your local
environmental authority or ask the shop where you purchased the product
for collection or recycling options.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may void
authority to operate the equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la
classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
cTUVus
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory model T146.
Input ratings: 100-240Vac, 2.7A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time without
notice.
2
Table of Contents
Introduction 4
Positioning the projector 6
Connecting a computer source 7
USB Mini B connection 7
VGA connection 7
Connecting power 7
Optional computer connections 7
Displaying an image 8
Adjusting the image 9
Connecting a video device 10
Video device connections 10
Composite video connection 10
VGA connection 10
Component video connection 10
S-video connection 10
Shutting down the projector 11
Troubleshooting your setup 11
Using the remote control 19
Using the audio 20
Using the keypad buttons 21
Optimizing computer images 22
Presentation features 22
Optimizing video images 23
Customizing the projector 23
Dynamic Messaging 23
Using the menus 24
Basic Menu 25
Advanced Menu 26
Maintenance 30
Cleaning the lens 30
Using the security lock 30
Replacing the projection lamp 31
3
Important Operating Considerations for Safety
• Refer to this guide for proper startup and shutdown procedures.
• Follow all warnings and cautions in this manual and on the projector.
• Place the projector in a horizontal position no greater than 15 degrees off
axis.
• Locate the projector at least 4' (1.2m) away from any heating or cooling
vents.
• Do not block ventilation openings. Locate the projector in a well-ventilated
area without obstructions to intake or exhaust vents. Do not place the
projector on a tablecloth or other soft covering that may block the vents.
• Do not place the projector in direct sunlight, humid, greasy or dusty places or
in places where the projector may come into contact with smoke or steam.
• Do not touch or block the projector lens with any objects as this can damage
the projector lens. Use the lens cap when the projector is not in use and
during transport. Scratches, gouges and other lens damage are not covered by
the product warranty.
• Do not look directly into the lens while the projector is being used.
• Do not drop the projector.
• Do not spill liquid on the projector. Spilled liquid may damage the projector.
• Use the power cord provided. Connect the power cord to a receptacle with
a protective safety (earth) ground terminal. A surge-protected power strip is
recommended.
• Do not overload wall outlets.
• When disconnecting the power cord, hold the plug, not the cord.
• Wash hands after handling the cables supplied with this product.
• The projector remote control uses batteries. Make sure the batteries’
polarity (+/-) is aligned correctly. Dispose of used batteries in accordance
with local disposal laws.
• Use an InFocus approved ceiling mount kit for proper fitting, ventilation and
installation. The warranty does not cover any damage caused by use of non-
approved ceiling mount kits or by installing in an improper location.
• When the projector is ceiling mounted, wear protective eyewear to prevent
eye injury before opening lamp door.
• Refer all service to qualified service personnel. Servicing your own projector
can be dangerous to you and will void the warranty.
• Only use replacement parts specified by InFocus. Unauthorized substitutions
may result in fire, electrical shock, or injury, and may void the warranty
• Only genuine InFocus lamps are tested for use in this projector. Use of non
InFocus lamps may cause electrical shock and fire, and may void the projector
warranty.
• Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
• The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
• In the unlikely event of a lamp rupture, particles may exit through the
projector vents. Keep people, food, and drinks out of the "keep out" area
under and around the projector, as indicated by the "X" areas below.
Follow these instructions to help ensure image quality and lamp life over the life of
the projector. Failure to follow these instructions may affect the warranty. For
complete details of the warranty, see the Warranty Booklet.
5’/1.5m
8’/2.4m
3’ / 1 m
2’ / 0.6 m
4
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward
to maintain. It is a versatile projector that is flexible enough for business
presentations and home video viewing too. IN146 has native WXGA 1280 x 800
resolution. It is compatible with a wide variety of computers and video devices.
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our
website at www.infocus.com, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the included
Quick Start Booklet. Optional accessories can be found on our website at
www.infocus.com or at your retailer or dealer.
Online registration
Register your projector on our website at www.infocus.com/register to activate
your warranty and receive product updates, announcements, and registration
incentives.
focus
keypad
lens
remote control
receiver (IR)
connector
panel
remote control
receiver (IR)
power cord
connector
5
Connector panel
The projector provides both computer and video connection options, including:
• VGA computer
• Composite video
•HDMI
•S-video
• USB mini B connector for firmware upgrades and presentation slide control.
• Monitor out, for VGA pass through to an external monitor.
• Audio input for video and computer.
• Audio output to external speakers.
• RS-232 serial control. Command control codes are on our support website at
www.infocus.com/support.
RS 232
computer
composite
video
audio in/out
security lock
S-video
monitor
out
HDMI
USB mini B
6
Positioning the projector
To determine where to position the projector, consider the size and shape of your
screen, the location of your power outlets, and the distance between the projector
and the rest of your equipment. Here are some general guidelines:
• Position the projector between 30 inches (.75m) and 65 inches (1.65m) from
the screen. To ensure adequate cable access, do not place the projector
within 24 inches (.61m) of a wall or other object.
• If you are installing the projector on the ceiling, we strongly recommend using
InFocus approved ceiling mounts for proper fitting, ventilation and installation.
Refer to the installation guide that comes with the InFocus Ceiling Mount Kit
(p/n SP-CEIL-UNIV) for more information. The warranty does not cover any
damage caused by use of non-approved ceiling mount kits or by installing in an
improper location. To turn the image upside down, see “Ceiling mount” on
page 28. We recommend using an InFocus authorized ceiling mount.
• Position the projector the desired distance from the screen. The distance
from the lens of the projector to the screen and the video format determine
the size of the projected image. (The throw ratio of the IN146 is 0.49:1.)
• IN146 image offset is 5% +/-2%. This means that if you have an image 40
inches (1 meter) tall from a table-mounted projector, the bottom of the
image will be 2 inches (5 cm) above the centerline of the lens.
Table 1: Screen Size
Diagonal Screen
Size
Size of the Projected Image
Width
Projection
Distance (L)
Minimum
Feet Inches Meters Inches Milimeters Meters Inches
5.9 71 1.8 60 153 0.75 30
6.7 80 2.0 64 163 0.8 33
7.5 90 2.3 72 183 0.9 37
8.3 100 2.5 80 203 1.1 41
10.0 120 3.0 96 244 1.3 50
12.5 150 3.8 120 305 1.6 62
13.0 156 4.0 133 337 1.65 65
7
Connecting a computer source
VGA connection
Connect one end of the provided computer cable to the Computer 1/Computer 2
connector on the projector and the other to the VGA connector on your
computer. If you are using a desktop computer, you will need to disconnect the
monitor cable from the computer’s video port first.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI
provides an interface between sources, such as set-top boxes, DVD players, and
receivers and your projector. Plug an HDMI cable into the video-out connector on
the video device and into the HDMI connector on the projector.
Connecting power
Connect the black power cord to the Power connector on the rear of the
projector and to your electrical outlet. The Power light on the Status Indicator
Panel (page 11) turns amber. NOTE: Always use the power cord that shipped with
the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In connector on the projector. You
may also need an adapter.
If you are using a desktop computer and want to see the image on your computer
screen as well as on the projection screen, connect to the desktop’s computer
cable to Computer 1 and the desktop’s monitor cable to the Monitor Out
connector on the projector.
connect VGA cable
connect HDMI
connect power
connect audio cable
8
Displaying an image
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp comes
on, the start up screen displays and the Power button is steady green. It can take
up to a minute for the image to achieve full brightness.
? No start up screen? Get help on page 12.
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the Source
button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector:
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD key
turns the external display on and off. Locate a function key labeled CRT/LCD or a
function key with a monitor symbol. Press FN and the labeled function key
simultaneously.
Refer to your laptop's documentation for more information about your laptop's
key combination or go to the InFocus website at: http://www.infocus.com/
Support/LaptopActivation.aspx.
? No laptop image? Try pressing the AUTO IMAGE button on the keypad.
Get help on page 12.
press Power button
turn on computer or
video device
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
9
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot release
button to extend the foot.
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the front of the projector.
Position the projector the desired distance from the screen at a 90 degree angle to
the screen.
See page 6 for a table listing screen sizes and distances.
Adjust the focus.
If the image is not square, first make sure that the projector is perpendicular to the
screen. If the image is larger or smaller on the top or bottom edge of the screen,
press the top Keystone button to reduce the upper part of the image, and press
the bottom Keystone button to reduce the lower part.
If the left or right side of the screen is larger or smaller the other, you can turn the
projector to the left or to the right a few degrees to square the image.
Adjust the Contrast or Brightness in the Basic Menu. See page 26 for help with
these menu adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for 16:9 in
order to view the highest quality image. For more information regarding Aspect
Ratio, see page 10.
adjust height
release button
elevator
foot
adjust distance
adjust focus
focus
adjust keystone
Aspect Ratio
Auto Image
Brightness
Contrast
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Advanced Menu
◄ Auto ►
Execute
50
50
50
Presentation
50
50
Off
( Basic Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
adjust Basic Menu
10
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders, digital
cameras, video game consoles, HDTV receivers, and TV tuners to the projector.
You can connect the audio directly to the projector to get sound from the built-in
speaker, or you can bypass the projector’s audio system and connect the audio
directly from your source to a stereo or home theater system.
You can connect the projector to most video devices that can output video. You
cannot directly connect the coaxial cable that enters your house from a cable or
satellite company, the signal must pass through a tuner first. Examples of tuners
are digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.
Basically, any device that can change channels is considered a tuner.
Before connecting your projector, you should decide which aspect ratio you want
to use. The projector’s Aspect Ratio setting is accessed through the Resize button
on the remote or through the projector’s Basic Menu. See page 26 for more
information.
Video device connections
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI
provides an interface between sources, such as set-top boxes, DVD players, and
receivers and your projector. Plug an HDMI cable into the video-out connector on
the video device and into the HDMI connector on the projector.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out connector
on the video device. Plug the other yellow connector into the yellow Video
connector on the projector.
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This connector
may be labeled “To Monitor” on the video source. Plug the computer cable into
the Computer connector on the projector.
Component video connection
If your HD video device has component connectors, an optional Component to
VGA adapter can be used. Plug the component cable into the video device. Plug
the other end of the component cable into the adapter and plug the adapter into
the Computer connector.
S-video connection
Plug the S-video cable’s connector into the video-out connector on the video
device. Plug the other connector into the black S-Video connector on the
projector.
Audio
For audio, connect a 3.5mm stereo cable to the Audio In connector on the
projector and to your source. If your source uses RCA audio connectors, a Y-
cable or adapter may be used. (Note: A separate audio connection is not required
for HDMI source inputs.
11
Shutting down the projector
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction with the
projector is performed for 30 minutes. By default, this feature is off. You can
change the length of time, see page 30.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. The
lamp turns off and the LED blinks amber for 1 minute while the fans continue to
run to cool the lamp. When the lamp has cooled, the LED lights amber and the
fans stop. Unplug the power cable to completely power off the projector.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it does
not, troubleshoot the setup.
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
Table 2: Status indicator light behavior and meaning
Icon Meaning
Power, solid amber
Power, blinking green
Power, solid green
Power, blinking amber
The projector is plugged in.
The power button has been pressed and
the software is initializing.
The projector is on and initialized.
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
Thermometer, solid red The projector is too hot. Make sure the
vents aren’t blocked (see page 18). Turn
off the projector and wait one minute,
then turn the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact
service.
Lamp, solid red If the Lamp LED is on and the other LEDs
are off, turn off the projector and wait
one minute; then turn the projector on
again. If the LED behavior continues (and
the other LEDs are off), replace the lamp
and reset the lamp timer. If multiple LEDs
are on simultaneously or if the behavior
continues, contact Technical Support.
Repair may be needed.
Problem Solution Result
No start up screen Plug power cord into the projector
press power button
Startup
Screen
Correct image
A
Startup
Screen
Only start up screen appears
Restart laptop
Press the Source button
activate laptop’s external port
A
A
Computer image projected
12
13
Problem Solution Result
No computer image, just the words “Signal out of
range”
Signal out of
the range
A
Press the AUTO IMAGE button on keypad
Adjust computer refresh rate in Control Panel > Display
> Settings > Advanced > Adapter (location varies by
operating system)
You may also need to set a different resolution on your
computer, as shown in the following problem, “image
fuzzy or cropped”
Computer image projected
A
A
14
Only my laptop’s background appears, not the
Desktop icons
A
A
Disable “Extend my Windows Desktop” in Control
Panel > Display > Settings > Display 2 (location varies by
operating system)
Uncheck this
option, then
click Apply
Background and Desktop projected
A
A
Image fuzzy or cropped
A
A
For a laptop,
disable laptop
monitor or turn-
on dual-display
mode
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
A
Image clear and not cropped
Problem Solution Result
15
Image not centered on screen
Ceiling Mount
Digital Zoom
Horz Shift
Vert Shift
Magnify Level
Rear Project
Magnify Position
Previous
Off
50
50
50
50
Off
( Image Setup ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Adjust horizontal or
vertical position in
Advanced Menu >
Setup > Image Setup...
menu
Move projector, adjust height Correct image
Image not square Adjust Keystone on keypad Square image
Problem Solution Result
16
Image not sharp
Aspect Ratio
Auto Image
Brightness
Contrast
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Advanced Menu
◄ Auto ►
Execute
50
50
50
Presentation
50
50
Off
( Basic Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Adjust Sharpness in the Basic Menu Correct image
Image does not fit 4:3 or 16:9 screen
Aspect Ratio
Auto Image
Brightness
Contrast
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Advanced Menu
◄ Auto ►
Execute
50
50
50
Presentation
50
50
Off
( Basic Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Change aspect ratio to 4:3 or 16:9 in Basic Menu >
Aspect Ratio menu
Correct image
Problem Solution Result
A
17
Image upside down
Aspect Ratio
Auto Image
Brightness
Contrast
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Advanced Menu
◄ Auto ►
Execute
50
50
50
Presentation
50
50
Off
( Basic Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Turn off Ceiling Mount in Basic menu Correct image
Image reversed left to right
A
Ceiling Mount
Digital Zoom
Horz Shift
Vert Shift
Magnify Level
Rear Project
Magnify Position
Previous
Off
50
50
50
50
Off
( Image Setup ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Turn off Rear Project in Advanced Menu > Setup >
Image Setup... menu Correct image
COLOR
Projected colors don’t match source
BrilliantColor™
Color
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Color Space
Color Temp
Gamma
Tint
White Peaking
Previous
Normal Look
50
50
50
50
50
50
50
Auto
Bright
CRT
50
50
( Color ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Adjust the items in the Advanced Menu > Image >
Color... menu
COLOR
Correct image
Problem Solution Result
18
The video embedded in my PowerPoint presentation
does not play on the screen
A
A
B
B
Turn off the internal LCD display on your laptop Embedded video plays correctly
A
A
B
B
Overheating
indicator
Lamp won’t turn on, the projector is overheating Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Startup
Screen
Lamp turns on
Problem Solution Result
19
Still need assistance?
If you need assistance, visit our website at www.infocus.com/support or call us.
Check out our HOW TO section there for additional information on using this
projector for home theater or gaming applications. See the Quick Start Poster/
Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan may be
purchased from your dealer. When sending the projector in for repair, we
recommend shipping the unit in its original packing material, or having a
professional packaging company pack the unit. Please insure your shipment for its
full value.
“Replace lamp” message appears at startup, lamp
won’t turn on
lamp door
replace lamp
Lamp must be replaced (see page 32)
Startup
Screen
Lamp turns on
Problem Solution Result
20
Using the remote control
The remote uses two (2) AA batteries (not provided). They are easily installed by
removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
Caution:
• When replacing the remote batteries, be aware that using batteries other
than AA batteries may risk severe damage to the remote. When disposing of
the batteries, be sure to do so in an enviromentally proper manner.
• If the remote control gets wet, wipe it dry immediately.
•Avoid excessive heat and humidity.
• Ensure the batteries' polarity (+/-) is aligned correctly.
• Do not mix new and old batteries together, or mix different types of batter-
ies together.
• Replace the batteries as soon as they run out.
• Remove batteries from the remote control when storing or not in use for a
prolonged period.
To operate, point the remote at the front of the projector (not at the computer).
The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see page 11 for
shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use the
arrow buttons to navigate, and the Select button to select features and adjust
values in the menus. See page 25 for more info on the menus.
The remote also has:
•Volume buttons to adjust the sound.
•Custom button that can be assigned to a special function, like Blank Screen or
Freeze (see page 28).
•Source button brings up a menu of all possible sources allowing the user to
switch the active source.
•Blank button to blank the screen.
•Presets button to select stored settings (see page 26).
•Mute button to silence the audio.
•Auto Image button to resynch the projector to the source.
•Resize button to switch among aspect ratios (see page 26).
•Help button to get help with connecting sources and improving the picture.
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are not
dead.
• Make sure you’re pointing the remote at the projector or the screen, not the
computer, and are within the remote range of 15 feet (4.5m). For best
results, point the remote at the projector.
navigation
buttons
21
Using the audio
Using the projector’s speakers
Connect the audio source to the Audio In connectors to hear audio through the
projector speakers.
Amplified speakers may also be connected to the projector using the Audio Out
connector.
To adjust the volume, press the Volume buttons on the remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
• Make sure the audio cable is connected to the Audio In connector on the
projector, and that the other end of the cable is connected to an Audio Out
connector on the source (not a “line-in” or “microphone” connector).
• Make sure the volume is turned up enough. Press the Volume button on the
remote.
• Make sure the correct source is active.
• Adjust the audio source.
• If playing a video, make sure the playback has not been paused.
connect audio cable
22
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of
their functions:
Power–turns the projector on and off (page 8).
Auto Image–resets the projector to the source (page 22).
Presets / Select–cycles through the available preset settings (page 26) / confirms
choices made in the menus (page 25).
Keystone–adjusts squareness of the image (page 9).
Menu–opens the on-screen menus (page 25).
Up/Down/Left/Right arrows–navigates to and adjusts settings in the menus
(page 25).
Volume–adjusts sound (page 21).
Source–brings up a menu with all possible sources, allowing the user to change the
active source (page 8).
menu navigation
buttons
23
Optimizing computer images
After the projector is running and the image is on the screen, you can optimize the
image using the onscreen menus. For general information on using the menus, see
page 25.
• Select default image settings using a preset appropriate to your environment.
• Adjust the Keystone, Contrast, or Brightness (page 26).
• Change the Aspect Ratio. Choose the option that best fits your input source
(page 26).
• Adjust the Color Temperature (page 27).
• Adjust the Phase, Tracking, or Horizontal or Vertical position (page 27).
• Once you have optimized the image for a particular source, you can save the
settings using Presets. This allows you to quickly recall these settings later
(page 26).
Presentation features
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
• The Custom key allows you to assign various features to the button. The
default effect is Source Info, which displays information about the projector
and current source. See page 28 for details.
• The Search Screen option lets you change the appearance of the blank screen
and start up screen (page 29).
• Auto Off Time is provided to automatically shut down the projector after
several minutes. This helps preserve lamp life (page 29).
24
Optimizing video images
After your video device is connected properly and the image is on the screen, you
can optimize the image using the onscreen menus. For general information on
using the menus, see page 25.
• Adjust the Keystone, Contrast, Brightness, Color, or Tint (page 26).
• Change the Aspect Ratio. Choose the option that best fits your input source
(page 26).
• Select a Sharpness setting (page 26).
• Adjust the Color Temperature. Select a listed warmth value (page 27).
• Turn on Overscan to remove noise on the edges of the image (page 27).
Customizing the projector
You can customize the projector for your specific setup and needs. See page 28
for details on these features.
• For rear projection, turn Rear Project on in the Advanced Menu > Setup >
Image Setup... menu.
• For ceiling mounted projection, turn Ceiling Mount on in the Basic menu.
• Specify which source the projector checks first for active video during power-
up.
• Specify the function of the Custom key on the remote.
• Turn the projector’s display messages on and off.
• Turn on power saving features.
• Specify appearance of blank screen and startup screen.
• Specify the language viewed on the menus.
• Save settings for the active source as a preset.
Dynamic Messaging
Using command codes, text messages can be sent for display by the projector (and
all other InFocus projectors with the Dynamic Messaging feature) over a network
or serial connection. Text is shown on top of whatever else is being displayed, and
can be shown in ticker tape format or in a box, with optional beep tone alert. This
is a great way to display urgent alert messages to employees, and simply requires a
connection to the projector RS-232 serial control or LAN connector. Command
codes for executing Dynamic Messaging are available on our website at
www.infocus.com/support.
25
Using the menus
1To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use the
arrow buttons to move up and down to review the menu options.
2To enter a submenu, highlight the desired submenu and press Select.
3To adjust a menu setting, highlight the desired menu option and press Select or
>. Then press < or > to scroll through the available adjustments. To save your
adjustments, press Select.
4Press the Menu button to exit the menu system.
The menus are grouped by usage:
• The Basic Menu provides common image adjustments.
• The Advanced Menu provides more complex image adjustments.
keypad navigation
buttons
Image
Serial
Setup
Status/Service
Basic Menu
3D Control...
Color...
PC...
Video...
(
Advanced Menu
) SN: BHQM91001936
MDL: IN146
FW: 0.19
Aspect Ratio
Auto Image
Brightness
Contrast
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Advanced Menu
◄ Auto ►
Execute
50
50
50
Presentation
50
50
Off
(
Basic Menu
) SN: BHQM91001936
MDL: IN146
FW: 0.19
Basic Menu Advanced Menu
26
Basic Menu
To adjust the following settings, highlight the setting, press Select, use the right and
left arrows to adjust the values, then press Select to confirm the changes.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch enhanced
widescreen DVDs.
For more information regarding Aspect Ratio, see page 10.
Auto Image: resets the projector to the source.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest parts
of the picture and changes the amount of black and white in the image.
Keystone: adjusts the image vertically and makes a squarer image. You can also
adjust keystone from the keypad.
Presets: Presets are provided that optimize the projector for displaying computer
presentations and video images under certain conditions. Note: User changes are
temporarily saved as User Presets.
Sharpness: (video sources only) changes the clarity of the edges of a video image.
Select a sharpness setting.
Volume: increases or decreases the audio volume.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Basic Menu
Aspect Ratio
Auto Image
Brightness
Contrast
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Advanced Menu
◄ Auto ►
Execute
50
50
50
Presentation
50
50
Off
( Basic Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Aspect Ratio
Auto Image
Brightness
Contrast
Keystone
Presets
Sharpness
Volume
Ceiling Mount
Advanced Menu
◄ Auto ►
Execute
50
50
50
Presentation
50
50
Off
( Basic Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Aspect ratio
increasing keystone decreasing keystone
27
Advanced Menu
Image:
3D Control:
3D Control: allows you to enjoy 3D (stereoscopic) content. Your IN146 sup-
ports two synchronization modes (External Sync and DLP Link™) for con-
trolling LCD shutter glasses. In addition to the projector, you will need a pair
of 3D shutter glasses, 3D content, and 3D compatible source (and emitter).
Ensure the glasses you choose are consistent with the synchronization mode
you will be using.
3D Sync Invert: (Only applies when 3D control is set to DLP Link™.) If the
image appears to flutter, look odd or if the image depth looks off or you
experience eye strain, turn this feature on to see if the image improves.
Color...
BrilliantColor™: produces an expanded on-screen color spectrum that deliv-
ers enhanced color saturation for bright, true-to-life images. Choose Normal
Look for most video sources and Bright Look for most computer sources.
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Red/Green/Blue Gain: adjusts the gain of the red, green or blue channel of the
image.
Red/Green/Blue Offset: adjusts the offset of the red, green or blue channel of
the image.
Color Space: applies to computer and component video sources. It allows
you to select a color space that has been specifically tuned for the input signal.
When Auto is selected, the projector automatically determines the standard.
To choose a different setting, turn off Auto, then choose RGB for computer
sources or choose either REC709 or REC601 for component video sources.
Color Temperature: changes the intensity of the colors. Select a listed rela-
tive warmth value.
Gamma: select the appropriate gamma from among Video, Film, Bright, and
CRT.
Tint: adjusts the red-green color balance in the image of NTSC video images.
The tint setting applies to NTSC video sources only.
White Peaking: increases the brightness of whites that are near 100%.
PC:
Force Wide: when this is off, the analog locking algorithms choose the stan-
dard mode resolution (4:3) as the preferred default resolution. When this is
on, the analog locking algorithms choose wide mode resolution (16:10) as the
preferred default resolution.
Phase: adjusts the horizontal phase of a computer source.
Prevent PC Screen Saver: prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for
this feature to work.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
Video:
Detect Film: determines whether the original source of the input video was
film (progressive) or video (interlaced).
Overscan: removes noise around the video image.
Set Black Level...: analyzes the current input image and calculates an offset
value which is then added to the analog to digital converter black level value.
This ensures optimum black level for each analog source.
Image
Serial
Setup
Status/Service
Basic Menu
3D Control...
Color...
PC...
Video...
( Advanced Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
Advanced Menu
28
Serial:
Serial Port Baud Rate: selects the serial port and baud rate.
Serial Port Echo: controls whether the serial port echoes characters.
Setup:
Audio Setup...
Internal Speaker: turns the internal speaker on or off.
Power Sounds: controls whether the projector makes a sound when pow-
ered on and off.
Closed Captioning...
Closed Captions: controls closed captioning. If the source is NTSC and
contains captions on the selected channel, then the projector will display
caption text overlaid on the image. When Closed Captions is off and volume
is muted, closed captioning will appear. Options are: Off, CC1 and CC2.
Image Setup...
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Digital Zoom: reduces the size of projector’s display area. If the display area
has been resized by this setting, it can be moved by changing the Horz Shift
and Vert Shift settings.
Horz Shift/Vert Shift: moves the display area horizontally or vertically if its
size has been changed by the Digital Zoom setting.
Magnify Level: magnifies the image.
Rear Project: reverses the image so you can project from behind a translu-
cent screen.
Magnify Position: moves the magnified image.
Keypad/Remote Settings...
Blank Key: select what to display when the blank key on the remote is
pressed: your custom snapshot, a solid color screen (blue, black or white),
the factory logo screen, a timer, or test patterns. The timer option is useful
for classroom tests or break times during meetings.
Custom Key: allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and press
Select to choose a different one.
•Blank Screen: displays an empty screen.
•Mute: turns off all sound.
•Source: cycles through available sources.
•Auto Image: resets the projector to the source (page 22).
•Freeze Screen: pauses the projected image.
•Source Info: the default action. Shows the Source Info menu.
•Projector Info: shows the Projector Info menu.
•Overscan: removes noise around the image.
•AV Mute: enables or disables AV Mute function.
•Closed Captions: enables or disables Closed Captions.
Keypad: enables or locks the projector keypad.
Source Key 1/2/3: defines the source being displayed when the Source Key 1/
2/3 is pressed if there is Source Key 1/2/3 on your Infocus projector remote
control.
29
Lamp...
Lamp Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector qui-
eter.
OSD Setup...
Language: allows you to select a language for the onscreen display.
Menu Position: allows you to change the position of the On Screen Display
items.
Menu Transparency: allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image
behind the menu is visible.
Show Messages: displays status messages (such as “Searching”) in the lower-
left corner of the screen.
PIN Settings
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you must
enter the PIN before you can project an image. The default PIN on this pro-
jector is Menu-Source-Select-Up-Down. Use the navigation buttons on the
remote or keypad to enter the correct 5-button press sequence. When all 5
numbers are entered correctly, press the Select button on the remote or
keypad to select OK. If the message “Wrong PIN” appears, verify the code
and re-enter it. If you mis-enter a number, you must enter 5 numbers and
press the Select button in order to access the “Wrong PIN” message and re-
enter the code.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the startup
screen. Enter the PIN. Use the navigation buttons on the remote or keypad
to enter the correct button press sequence. See the description above for
instructions.
To change the PIN:
Select “Change PIN...” in the Advanced Menu > Setup > PIN settings menu.
Enter the existing PIN. Enter the new PIN. You can navigate between OK and
Cancel by pressing the up and down buttons on the keypad. Select OK or
Cancel by pressing the Select button. Verify the new PIN.
If you lose or forget your custom PIN: Contact InFocus support. Go to
www.infocus.com/support
Power
AC Power On: When this feature is on, the projector automatically turns on
when electrical power is connected. This allows control of ceiling mounted
projectors with a wall power switch.
Power Saving Mode: When Power Saving Mode is On, the monitor out func-
tion will not work when the projector is in standby (powered off but con-
nected to AC Power).
Snapshot
Take Snapshot...: captures the current image and allows it to be used as the
search screen image.
Disable Snapshot: allows the user to disable the snapshot capability.
Source
Auto Source: When this feature is On, the projector automatically finds the
active source, checking the selected Power-up Source first. When this feature
is Off, the projector defaults to the source selected in Power-up Source. To
display another source, you must manually select one by pressing the Source
button on the remote or keypad.
Power-up Source: determines which source the projector checks first for
active video during power-up.
Search Screen: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
30
Timer
Auto Off Time: automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received before
the projector powers down, the image will be displayed.
High Altitude Setting
High Altitude Setting: We recommend you turn on the High Altitude Mode
when your environment is between 1500 m - 3000 m above sea level.
Status/Service:
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings.
Reset Lamp Hours...: resets the lamp hours used counter in the Projector
Info menu to zero. Do this only after changing the lamp.
Factory Reset...: restores all settings to their default.
Service Code...: only used by authorized service personnel.
31
Maintenance
Cleaning the lens
1Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
•Projector must be off and the lens must be at room temperature.
•Avoid using an excessive amount of cleaner, and don’t apply the cleaner
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals
might scratch the lens.
2Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
•Turn the projector off and unplug power cord before cleaning any part of
the projector.
•Do not touch or block the projector lens with any objects as this can
damage the projector lens. Use the lens cap when the projector is not in
use and during transport. Scratches, gouges and other lens damage are not
covered by the product warranty.
•Do not open any cover on the projector, except the lamp cover.
•Do not attempt to service this product yourself as opening and removing
covers may expose you to dangerous voltage and other hazards. Refer all
servicing to qualified service personnel.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the
information that came with the lock for instructions on how to use it.
security
lock
32
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the
lamp has been in use. Twenty hours before the lamp life expires, the message
“Replace lamp” appears on the screen at startup.
•NOTE: Be sure to use the InFocus lamp module designed for this projector.
You can order new lamps from www.infocus.com (in select areas), your
retailer or your dealer. Only genuine InFocus lamps are tested for use in this
projector. Use of non InFocus lamps may cause electrical shock and fire, and
may void the projector warranty. InFocus is not liable for the performance,
safety or certification of any other lamps.
WARNINGS:
• The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
• To avoid burns, allow the projector to cool for at least 60 minutes before you
replace the lamp.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass surface of the lamp module. Fingerprints can obscure
projection sharpness and may cause the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely event
that the lamp ruptures, small glass fragments may be generated. The lamp
module is designed to contain most of these fragments, but use caution when
removing it.
• Before replacing a ruptured lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement.
• When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
Hg – Lamp contains mercury. Manage in accordance with local disposal
laws. See www.lamprecycle.org.
33
1Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly.
3Remove the lamp door, located on top of the projector, by removing the two
screws on either side of the lamp door, and lifting the lamp door off using the
latch at the front ofthe projector.
4Loosen the captive screw that attaches the lamp housing to the projector.
NOTE: If the projector is installed on a ceiling mount, be careful not to drop
the lamp module once the captive screw is loosened.
5Carefully lift the lamp straight up, off of the alignment pins; being careful not to
pinch the lamp connector. Dispose of the lamp in an environmentally proper
manner.
6Install the new lamp module, aligning the pins properly. Be careful not to pinch
the lamp connector.
7Tighten the screw. (NOTE: If the pins have not been aligned properly, the
screw will not tighten securely.)
8Replace the lamp door by (a) aligning the hinges, (b) putting the lamp door
down and (c) locking it back into place.
9Replace the lamp door screws and tighten securely.
10 Plug in the power cord and press the Power button to turn the projector back
on.
11 To reset the lamp hour timer, navigate to the Advanced Menu > Status/Service
menu and select Reset Lamp Hours.... See page 31 for details.
turn off and unplug
projector
wait 60 minutes
loosen screw
Image
Serial
Setup
Status/Service
Basic Menu
Source Info...
Projector Info...
Reset Lamp Hours...
Factory Reset...
Service Code...
( Advanced Menu ) SN: BHQM91001936
MDL: IN146
FW: 0.19
34
INDEX
Numerics
3D Sync Invert 26
A
AC Power On 28
Aspect Ratio 11, 25
Audio In Computer connector 7
Auto Image 25
Auto Off Time 29
Auto Source 28
AV Mute 27
B
Blank Key 27
Blank Screen 27
Brightness 25
C
Cable box 10
Ceiling Mount 27
Closed Captions 27
Color Space 26
Computer In connector 7
Connecting
Video device 10
Contacting InFocus 18
Contrast 25
Customer service contact information 18
D
Detect Film 26
Digital Zoom 27
Disable Snapshot 28
F
Factory Reset 29
Focus 9
Force wide 26
Freeze Screen 27
G
Gamma 26
H
HDTV 25
High Altitude Setting 29
Horizontal Position 26
Horz Shift 27
I
Internal Speaker 27
K
Keypad 28
Keypad buttons 21
Keystone 25
Keystone, Adjusting 9
L
Lamp Low Power 28
M
Magnify Level 27
Menu Transparency 28
Menu usage 24
Menu-Source-Select-Up-Down 28
Mute 27
O
Overscan 26, 27
P
Phase 26
PIN Protect 28
Power connector 7
Power cord 7
Power Saving Mode 28
Power Sounds 27
Prevent PC Screen Saver 26
Projector
Connecting video devices 10
Keypad buttons 21
Menus 24
35
Positioning 6
Setting up 6
Troubleshooting problems 11
Projector Info 27, 29
R
Rear Project 27
Red/Green/Blue Gain 26
Red/Green/Blue Offset 26
Remote control 19
Reset 29
Resetting the projector 29
S
Screen Aspect 10
Search Screen 28
Serial Port Baud Rate 27
Serial Port Echo 27
Service 29
Set Black Level... 26
Sharpness 25
Show Messages 28
Source 27
Source Info 27, 29
Sync Threshold 26
T
Take Snapshot... 28
Tint 26
Tracking 26
Troubleshooting 11
TV tuner 10
U
USB 5
V
Vert Shift 27
Vertical Position 26
Volume 25
Volume button 20
W
Warranty 18

Navigation menu