Inkel ETR0004 TFT LCD TV MONITOR User Manual USERS MANUAL

INKEL Corporation TFT LCD TV MONITOR USERS MANUAL

UserManual.wiki >

Inkel >

ETR0004 User Manual HTML Version

USERS MANUAL

OPERATING INSTRUCTIONS

TL-1705W

17.1 inch WIDESCREEN TFT-LCD TV

Introduction

READ THIS BEFORE OPERATING YOUR UNIT

: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS

INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

WARNING

This symbol is intended to alert the user to the

presence of uninsulated "dangerous voltage"

within the product's enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

This symbol is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only.

Safety precaution with use of a polarized AC plug.

However, some products may be supplied with a nonpolarized plug.

FOR YOUR SAFETY

U.S.A

CANADA 120 V

Note to CATV System Installer :

This reminder is provided to call the CATV system installer’s attention to Article

820-40 of the NEC that provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as pracitcal.

FCC INFORMATION

: To prevent electric shock, match wide blade of plug to wide slot, fully

insert.

: Pour éviter chocs électriques, introduire la lame la plus large de la

fiche dans la borne correspondante de la prise et pousser jusqu’ au

fond.

CAUTION

ATTENTION

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFCATIONS TO THIS

EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO

OPERATE THE EQUIPMENT.

NOTE: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Caution : Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user’s authority to

operate the equipment.

1. Read Instructions - All the safety and operating instructions should

be read before the product is operated.

2. Retain instructions - The safety and operating instructions should

be retained for future reference.

3. Heed Warnings - All warnings on the product and in the operating

instructions should be adhered to.

4. Follow Insturctions - All operating and use instuctions should be

followed.

5. Cleaning - Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

6. Attachments - Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

7. Water and Moisture - Do not use this product near water - for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in

a wet basement, or near a swimming pool; and the like.

8. Accessories - Do not place this product on an unstable cart, stand,

tripod, bracket, or table. The product may fall, causing serious injury

to a child or adult, and serious damage to the product. Use only with

a cart, stand, tripod, bracket, or table recommended by the

manufacturer, or sold with the product. Any mounting of the product

should follow the manufacturer’s insturctions, and should use a

mounting accessory recommended by the manufacturer.

9. A product and cart combinaion should be moved with care. Quick

stops, excessive force, and uneven surfaces may cause the product

and cart combination to overturn.

10. Ventilation - Slots and openings in

the cabinet are provided for

ventilation and to ensure reliable

operation of the product and to

protect it from overheating, and

these openings must not be

blocked or covered. The openings

should never be blocked by placing

the product on a bed, sofa, rug, or other similar surface. This

product should not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the

manufacturer’s intructions have been adhered to.

11. Power Sources - This product should be operated only from the

type of power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult your product

dealer or local power company. For porducts intended to operate

from battery power, or other sources, refer to the operating

instructions.

12. Grounding or Polarization - This product may be equipped with a

polarized alternating-current line plug (a plug having one blade

wider than the other). This plug will fit into the power outlet only one

way. This is a safety feature. If you are unable to insert the plug

fully into the outlet, try reversing the plug. If the plug should still fail

to fit, contact your electrician to replae your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

Alternate Warnings - This product is equipped with a three-wire

grounding-type plug, a plug having a third(grounding) pin. This plug

will only fit into a grounding-type power outlet. this is a safety

feature. If you are unable to insert the plug into the outlet, contact

your electrician to replace your obsolete outlet. Do not defeat the

safety purpose of the gronding-type plug.

13. Power-Cord Protection - Power-supply cords should be routed so

that they are not likely to be walked on or pinched by items placed

upon or against them, paying particlar attention to cords at plugs,

convenience receptacles, and the point where they exit from the

product.

14. Outdoor Antenna Grounding - If an outside antenna or cable

system is connected to the product, be sure the antenna or cable

system is grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides information with

regard to proper grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna discharge unit, size of

grounding conductors, location of antenna-discharge unit,

connection to grounding electrodes, and requirements for the

grounding electrode. See Figure 1.

15. Lightning - For added protection for this product during a lightning

storm, or when it is left unattended and unused for long periods of

time, unplug it from the wall outlet and disconnect the antenna or

cable system. This will prevent damage to the product due to

lightning and power-line surges.

16. Power Lines - An outside antenna system should not be located in

the vicinity of overhead power lines or other electric light or power

circuits, or where it can fall into such power lines or circuits. When

installing an outside antenna system, extreme care should be taken

to keep from touching such power lines or circuits as contact with

them might be fatal.

17. Overloading - Do not overload wall outlets, extension cords, or

integral convenience receptacles as this can result in a risk of fire

or electric shock.

18. Object and Liquid Entry - Never push objects of any kind into this

product through openings as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing - Do not attempt to service this product yourself as

opening or removing covers may expose you to dangerous voltage

or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service - Unplug this product form the wall

outlet and refer servicing to qualified service personnel under the

following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation.

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance -

this indicates a need for service.

21. Replacement Parts - When replacement parts are required, be

sure the service technician has used replacement parts specified

by the manufacturer or have the same characteristics as the

original part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check - Upon completion of any service or repairs to this

product, ask the service technician to perform safety checks to

determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting - The product should be mounted to a

wall or ceiling only as recommended by the manufacturer.

24. Heat - The product should be situated away from heat sources

such as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

GROUND

CLAMP

GROUND CLAMPS

NEC-NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECRODE SYSTEM

(NEC ART 250, PART H)

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

PORTABLE CART WARNING

Figure 1

Example of antenna grounding as per

National Electrical Code, ANSI/NFPA 70

SAFETY INSTRUCTIONS

CONTENTS

Controls

Introduction

Installations

Operations

PC Display

Troubleshooting

READ THIS BEFORE OPERATING YOUR UNIT | 2

SAFETY INSTRUCTIONS | 3

FRONT OF THE TV | 5

REAR OF THE TV | 6

REMOTE CONTROL | 7

USING YOUR TV AS A COMPUTER(PC) DISPLAY | 60

| 63

| 66

Appendix

Specifications

RETRACTABLE STAND | 64

CLEANING AND MAINTAINING YOUR TV | 64

USING YOUR TV IN ANOTHER COUNTRY | 65

CONNECTING VHF AND UHF ANTENNAS | 8

CONNECTING CABLE TV | 9

CONNECTING VCR | 11

CONNECTING A S-VHS VCR | 13

CONNECTING DVD PLAYER | 13

CONNECTING DTV(SET-TOP BOX) | 14

CONNECTING POWER DC INPUT | 14

INSTALLING BATTERIES IN THE REMOTE CONTROL | 15

TURNING THE POWER ON/OFF | 16

VIEWING THE MENU | 16

SETTING THE OSD TIMEOUT | 17

SELECTING A MENU LANGUAGE | 18

SELECTING INPUT SOURCE | 19

ADJUSTING THE VOLUME | 22

LISTENING WITH HEADPHONES | 23

MEMORIZING THE CHANNELS | 24

CHANGING CHANNELS | 27

CUSTOMIZING THE PICTURE | 29

USING AUTOMATIC PICTURE SETTINGS | 30

CHANGING THE SCREEN SIZE | 30

CHANGING THE SCREEN POSITION | 30

VIEWING THE CURRENT STATUS | 31

CUSTOMIZING THE SOUND | 32

SELECTING A SURROUND SOUND | 33

Special Features SELECTING THE BACKGROUND OF MENU | 34

FINE TUNNING CHANNELS | 34

LABELING THE CHANNEL NAME | 35

FREEZING THE PICTURE | 36

DIGITAL PAN AND ZOOM | 37

CHOOSING A MULTI-CHANNEL SOUND (MTS) SOUNDTRACK | 39

SETTING THE CLOCK | 40

SETTING THE ON/OFF TIMER | 41

SETTING THE SLEEP TIMER | 44

ADJUSTING CLOSED CAPTION SETTINGS | 45

VIEWING CLOSED CAPTIONS | 47

CHANGING WINDOW LAYOUT | 48

VIEWING VARIOUS SOURCES SIMULTANEOUSLY | 48

BLOCKING THE CONTENTS | 53

CHILD LOCK | 58

FACTORY RESET | 59

Controls

CH VOL.

MENU SOURCE

1 2 3 4 5

STANDBY/ON

FRONT OF THE TV

CHANNEL UP/DOWN ( / )

Press to change channels. Also press to highlight

various items on the on-screen menu.

VOLUME UP/DOWN ( )

Press to increase or decrease the volume. Also

used to select items on the on-screen menu.

Press to see an on-screen menu of your TV’s

features.

SOURCE

Press to select input source.

STANDBY/ON

Press to turn the TV on and off.

SPEAKER

Remote Control Sensor

Aim the remote control towards this square on

the TV.

STANDBY indicator

Lights up red when you turn the power off.

The buttons on the front panel control our TV’s basic features, including the on-screen menu. To use the more

advanced features, you must use the remote control.

REAR OF THE TV

1 2 3 4 5 7 9 1086

POWER (DC) INPUT

PC VIDEO INPUT

Connect to the video output port on your PC.

PC AUDIO INPUT

Connect to the audio output jacks on your PC.

S-VIDEO INPUT

Connect to the S-Video jack of a VCR or

camcorder, etc.

COMPOSITE VIDEO INPUT

Connect to the composite(normal) video jack of a

VCR or camcorder, etc.

AUDIO INPUT

Connect to the audio jack of a VCR or

camcorder, etc.

COMPONENT(DVD/DTV) VIDEO INPUT

Connect to the component video jacks of a DVD

player or a Set-Top Box.

COMPONENT(DVD/DTV) AUDIO INPUT

Connect to the audio jacks of a DVD player or a

Set-Top Box.

HEADPHONE JACK

Connect a set of external headphones to this jack

for private listening.

ANTENNA INPUT

Connect to an antenna or a cable TV system.

For more information on connecting equipment, see "Installations" on page 8 and "USING YOUR TV AS A

COMPUTER(PC) DISPLAY" on page 60.

All the functions can be controlled with this remote control unit.

Some functions can also be adjusted with the buttons on the front panel of the set.

REMOTE CONTROL

POWER ON

Turns the TV on.

PC AUTO

Press to center the screen

automatically in PC mode.

SLEEP

Press to select a preset time

interval for automatic shutoff.

Displays the main on-screen

menu.

ENTER

Press to display current status

or enter into certain sub menu.

VOLUME UP/DOWN ( / )

Press to increase or decrease

the volume. (Also used to make

selections on the on-screen

menu.)

P.MODE (Picture Mode)

Press to select the preferred

picture setting.

P.SIZE (Picture Size)

Press to change the screen size .

CHILD LOCK

Press to lock the controlling TV

with buttons on the top panel.

ADD/ERASE

Press to add or erase channels

in the TV’s memory.

WINDOW SEL.

Press to select the one of the

window in each PIP mode.

PIP (Picture in Picture)

Each time this button is

pressed, the window layout is

changed.

POWER ONPOWER ON

PC AUTOPC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

1 2 3

4 5 6

7 8

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

MENUMENU MUTEMUTE

SOURCESOURCE

STSTANDBYANDBY

REMOTE CONTROL RM-501

131

STANDBY

Turns the TV off.

AUTOSET

Press to memorize the receptable

channels automatically.

PRE. CH (Previous Channel)

Tunes to the previous channel.

NUMBER BUTTONS

Press to select channels

directly on the TV.

MUTE

Press to temporarily cut off the

sound.

CHANNEL UP/DOWN ( / )

Press CH or to change

channels. (Also used to

highlight the items on the on-

screen menus.)

SURROUND

Press to enjoy surround sound.

MTS I/II

(Multichannel Television Sound)

Press to choose stereo, mono

or Seperate Audio

Program(SAP broadcast).

SOURCE

Press to select input signal

source.

STILL

Press to stop the action at a

particular scene. Press again to

resume normal video.

CAPTION

Controls the caption decoder.

SRC

Press to select the input source

for the sub picture in PIP mode.

SWAP

Exchanges the two video

signals that is currently

displayed on the screen in the

DW(Double Window) mode.

Plug the antenna lead into the TV antenna terminal on

the rear panel.

CONNECTING VHF AND UHF ANTENNAS

Installations

Antennas with 300-ohm Flat Twin Leads

Antennas with 75-ohm Round Leads

If your antenna has a set of leads that look like this,

see Antennas with 300-ohm Flat Twin Leads below.

If your antenna has one lead that looks like this, see

“Antennas with 75-ohm Round Leads” below.

If you have two antennas, see “Separate VHF and

UHF Antennas”, on page 9.

If you are using an off-air antenna antenna (such as a roof antenna or “rabbit ears”) that has 300-ohm twin

flat leads, follow the directions below.

1Place the wires from the twin leads under

the screws on a 300-75 ohm adaptor (not

supplied). Use a screwdriver to tighten the

screws.

ANTENNA

2Plug the adaptor into the TV antenna

terminal on the rear panel.

Please be certain that TV is unplugged from the AC outlet before making any connections.

Since different component often have different terminal names, carefully read the operating instructions of the

component connected.

Separate VHF and UHF Antennas

Cable without a Cable Box

Connecting to a Cable Box that Descrambles All Channels

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna

signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor

(available at most electronics shops).

UHF

VHF

1Connect both antenna leads to the

combiner.

ANTENNA

OUT

ANTENNA

1Find the cable that is connected to the

ANTENNA OUT terminal on your cable box.

ANTENNA

UHF

VHF

2Plug the combiner into the TV antenna

terminal on the rear panel.

CONNECTING CABLE TV

To connect to a cable TV system, follow the instructions below.

Plug the incoming cable into the TV antenna terminal

on the rear panel.

ANTENNA

Because this TV is cable-ready, you do not need a

cable box to view unscrambled cable channels.

This terminal might be labeled “ANT OUT”, “VHF

OUT”, or simply, “OUT”.

ANTENNA

2Connect the other end of this cable to the

TV antenna terminal on the rear panel.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will

need a two-way splitter, an RF(A/B) switch, and four lengths of coaxial cable. (These items are available at most

electronics stores.)

ANTENNA

Incoming

Cable Splitter

IN CABLE OUT

Cable Box

Incoming

Cable Splitter

1Find and disconnect the cable that is connected to the ANTENNA IN terminal on your cable box.

2Connect this cable to a two-way splitter.

3Connect a coaxial cable between an OUTPUT terminal on the splitter and the IN terminal on the

cable box.

This terminal might be labeled “ANT IN”, “VHF IN”, or simply “IN”.

IN CABLE OUT

Cable Box

Incoming

Cable Splitter

RF (A/B)

Switch

4Connect a coaxial cable between the ANTENNA OUT terminal on the cable box and the B-IN

terminal on the A/B switch.

IN CABLE OUT

Cable Box

Incoming

Cable Splitter

RF (A/B)

Switch

5Connect another cable between the other OUT terminal on the splitter and the A-IN terminal on

the RF(A/B) switch.

IN CABLE OUT

Cable Box

Incoming

Cable Splitter

ANTENNA

RF (A/B)

Switch

6Connect the last coaxial cable between the OUT terminal on the RF(A/B) switch and the VHF/UHF

terminal to the TV antenna terminal on the rear panel.

After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set

the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to

“B”, you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or

4.)

CONNECTING VCR

These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the

instructions on pages 8 - 9). Skip step 1 if you have not yet connected to an antenna or a cable system.

ANTENNA

1Unplug the cable or antenna from the rear

of the TV.

OUT

AUDIO

OUT

VIDEO

OUT

ANTENNA

VCR Rear Panel

Incoming

Cable or

Antenna

2Connect the cable or antenna to the

ANTENNA IN terminal on the rear of the

VCR.

3Connect a coaxial cable between the ANTENNA OUT terminal on the VCR and the antenna

terminal on the TV.

A coaxial cable is usually included with a VCR. (If not, check your local electronics store.)

Coaxial Cable

OUT

AUDIO

OUT

VIDEO

OUT

ANTENNA

VCR Rear Panel TV Rear Panel

-L

4Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO L/R

jacks on the TV.

Connect a video cable between the VIDEO OUT jack on the VCR and the COMPOSITE jack on

the TV.

OUT

AUDIO

OUT

VIDEO

OUT

ANTENNA

VCR Rear Panel

TV Rear Panel

AUDIO

S-VIDEO

VIDEO --

AV IN

L R

If you have a “mono”(non-stereo) VCR, use the Y-connector (not supplied) to hook up to the left and

right audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

Your TV can be connected to an s-video signal from an S-VHS VCR.

(This connection delivers a better picture as compared to a standard VHS VCR.)

CONNECTING A S-VHS VCR

1To begin, follow steps 1-3 in the previous section to connect the antenna or cable to your VCR

and your TV.

-L

Coaxial Cable

OUT

AUDIO

OUT

VIDEO

OUT

ANTENNA

VCR Rear Panel TV Rear Panel

2Connect a set of audio cables between the AUDIO OUT jacks on the VCR and the AUDIO L/R

jacks on the TV.

Connect a S-Video cable between the S-VIDEO OUT jack on the VCR and the S-VIDEO jack on

the TV.

AUDIO

S-VIDEO

VIDEO --

AV IN

L R

OUT

AUDIO

OUT

VIDEO

OUT S-VIDEO

OUT

ANTENNA

VCR Rear Panel

TV Rear Panel

The S-Video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

CONNECTING DVD PLAYER

Connect a set of audio cables between the AUDIO L/R jacks on the TV and the AUDIO OUT jacks on the

DVD player.

Connect a video cable between the COMPONENT(CR, CB, Y) jacks on the TV and the Pr, Pb, Y (or CR, CB,

Y) jacks on the DVD player.

AUDIO OUT

LPb

VIDEO OUT

COMPONENT VIDEO OUT

DVD Player Rear Panel TV Rear Panel

CRB

COMPONENT IN(DVD/DTV)

AUDIO

R L

For an explanation of component video, see your DVD player owner’s manual.

When you watch DVD, press SOURCE button on remote control to select DVD signal source.

CONNECTING DTV(SET-TOP BOX)

CONNECTING POWER DC INPUT

The connections for a typical set-top box are shown below.

Connect a set of audio cable between the AUDIO L/R jacks on the TV and the AUDIO OUT jacks on the

set-top box.

Connect a video cable between the COMPONENT(CR, CB, Y) jacks on the TV and the Pr, Pb, Y jacks on the

set-top box.

Connect to the power DC input termnal on the TV

AUDIO OUT

VIDEO OUT

COMPONENT VIDEO OUT

Set Top Box Rear Panel TV Rear Panel

CRB

COMPONENT IN(DVD/DTV)

AUDIO

R L

To a wall AC

outlet

For an explanation of component video, see your set-top box owner’s manual.

The component jacks for DVD player and set-top box are same, so the DVD player and set-top box cannot

be connected together.

Do not use an AC adapter other than the one supplied with this TV.

The AC adapter supplied is designed for use wih this TV.

If other AC adapter is used, this could damage this unit or result in a risk or fire.

INSTALLING BATTERIES IN THE REMOTE CONTROL

Pull the battery cover upward in the directions shown by

the arrow and remove it.

Insert two batteries (AAA size).

Make sure to match the “+” and “-” ends of the batteries

with the diagram inside the compartment.

3Replace the battery cover.

The remote control can be used up to about 23 feet from the TV.

Remove the batteries and store them in a cool, dry place if you won t be

using the remote control for a long time.

VIEWING THE MENU

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

After turning the power on, press MENU

button.

The main menu appears on the screen. Its

top side has 7 icons: tv, settings, picture,

window, audio, time and options.

The on-screen menus disappear from the screen

after several seconds. This time interval can be

adjusted in the [options]-[osd timeout] menu. See

page 17 for details.

CH VOL.

MENU SOURCE

STANDBY/ON

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

CH VOL.

MENU SOURCE

STANDBY/ON

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Operations

TURNING THE POWER ON/OFF

POWER ONPOWER ON

PC AUTOPC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILDCHILD

LOCKLOCK

WINDOW

SEL.

PIP SWAP SRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

1 2 3

4 5 6

7 8

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

MENUMENU MUTEMUTE

SOURCESOURCE

STSTANDBYANDBY

REMOTE CONTROL RM-501

1To turn the power on, press the POWER

ON button on the remote control.

You can also use the STANDBY/ON button

on top of the TV.

POWER ON

PC AUTOPC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

1 2 3

4 5 6

+100

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

SOURCE

STANDBY

REMOTE CONTROL RM-501

2To turn the power off, press the STANDBY

button on the remote control.

You can also use the STANDBY/ON button

on top of the TV.

In STANDBY mode, the standby indicator

on the front panel lights up red.

When the power operation is in STANDBY mode,

the apparatus is still connected on some AC line

voltages.

Please be sure to unplug the cord when you leave

home for, say, a vacation.

If the electricity fails or the AC input cord is

unplugged while the power is on and plugged it

again, your TV enters directly into STANDBY mode.

Depending on input source and some operation

status, some menus cannot be selected and the

conditions of menu may differ.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Use the or button to select one of the

icons. Then press button to access the

icon’s sub-menu.

You can also use the MENU, CHANNEL and VOLUME

buttons on the top panel of the TV to make

selections.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

SETTING THE OSD TIMEOUT

Press the MENU button to display the menu

and select [options] - [osd timeout] menu

using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select appropriate

osd timeout interval: 5, 15, 60 sec.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select [options].

Then press or button to select

[language].

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select appropriate

language : English, Spanish, French.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to display the menu.

SELECTING A MENU LANGUAGE

For explanation purposes, this instuctions explains the menu language displayed on the screen in English.

SELECTING INPUT SOURCE

You must select the appropriate mode in order to view each source on the TV.

Sources can be selected with automatic or manual method.

Auto-searching can be used with this method. You can set this method in on-screen menus.

Press the MENU button to display the menu

and select [options] - [source select] menu

using /and /buttons.

Press the SOURCE button to select a

source you want.

Each time this button is pressed, the TV searches

all sources and automatically detects one of

connected and turned-on equipments.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Auto Selection

Press or button to select the “auto”.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to display the menu

and select [options] - [source select] menu

using /and /buttons.

Press the SOURCE button to select a

source you want.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Manual Selection

Press or button to select the “manual”.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Each time this button is pressed, the source

will be changed as fjollows:

TV S-VIDEO AV DVD PC

DTV TV

In case of selecting PC, refer to “USING YOUR TV AS

A COMPUTER(PC) DISPLAY” on page 60.

Selecting A Broadcast Source

When you select the TV mode as input source, you should select the broadcast source.

Press the MENU button to display the menu

and select [tv] - [source] menu using /

and /buttons.

Press or button to select the

“antenna”(air) or “cable”.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

antenna : when viewing antenna(air) channels

cable : when viewing cable channels

ADJUSTING THE VOLUME

Press the VOL + or VOL - button to increase or

decrease the volume.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Auto Volume

Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the volume every time the

channel is changed. “auto volume” automatically adjusts the volume of the desired channel by lowering the sound

output when the modulation signal is high or by rasing the sound output when the modulation signal is low.

Press the MENU button to display the menu

and select [audio] - [auto volume] menu

using /and /buttons.

Pressing or button to select “on”.

To cancel auto volume function, select “off”.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

LISTENING WITH HEADPHONES

Using Mute

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

WINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH AUTOSET

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MUTE button

Then the sound is cut off and

is displayed at lower-right corner of the

screen.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

WINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH AUTOSET

MENUMENU MUTEMUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

To turn mute off, press the MUTE button

again or VOL +/-, SURR. button,etc.

Plug the headphones into the headphone jack on

rear of the TV.

No sound is heard from the TV speakers.

MEMORIZING THE CHANNELS

Stroing Channels In Memory (Automatic Method)

Once you have memorized the available channels, you can use the CH +/- buttons to scan the memorized channels.

Channels can be tuned with automatic or manual method.

Before memorizing channels, first select the broadcast source.(Refer to “Selecting A Broadcast Source” on page 21 )

All of the receivable channels can be stored by this method.

You would better use this method during installation of your TV.

Press the MENU button to display the menu

and select [tv] - [autoset] menu using /

and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press ENTER or button to begin autoset.

To stop autoset, press the MENU button.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

After all the receivable channels are stored,

the [tv] - [autoset] menu reappears.

Press the MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTOPC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

1 2 3

4 5 6

+100

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the AUTOSET button on the remote control.

Quick way

To stop autoset, press the MENU button.

Press or button to select “add” or

“erase”.

After selecting one of them, the

corresponding channel is added or erased.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to display the menu

and select [tv]-[channel] menu using /

and /buttons.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Adding And Erasing Channels (Manual Method)

Press button to select [edit channels]

menu.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select a channel to

be added or erased.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

If you want to add or erase another

channel(s), repeat the upper steps 1 to 4.

If not, press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

You can view any channel (including an erased

channel) by using the number buttons on the remote

control.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press ADD/ERASE button.

Quick way

Select the channel you want to add or erase

by pressing CH +/- buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

If you want to add or erase another

channel(s), repeat the above steps 1 to 3.

If not, press MENU button to exit.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select the "add" or

"erase".

To adjust other items as desired, repeat the

above steps 1 to 3.

You can view any channel (including an removed

channel) by using the number buttons on the remote

control.

CHANGING CHANNELS

Using the Channel +/- Buttons

Press the CH + or CH - button to change channels.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Whenever you press these buttons, the TV changes

channels in sequence. You will see all the channels

that have been memorized. You will not see

channels that were either erased or not memorized.

Press the MENU button to display the

menu and select [tv] - [channel] menu

using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Using On-Screen Menu

Press or to change channels.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Directly Accessing Channels

Selecting the Previous Channel

Press the PRE.CH button.

The TV will switch to the last channel viewed.

POWER ONPOWER ON

PC AUTOPC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

1 2 3

4 5 6

+100

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

SOURCE

STANDBY

REMOTE CONTROL RM-501

To quickly switch between two channels that are far

apart, tune to one channel, then use the number

button to select the second channel. Then, use the

PRE.CH button to quickly alternate between them.

Press the number buttons to go directly to a

channel.

For example, to select channel 71, press “7”, then

“1”. The TV will change channels after you press

the second number.

You can also change to single-digit channels as

follows: for channel 7,

just press “7”

or “0”, then “7”

or “0”, “0” then “7”

POWER ON

PC AUTOPC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

1 2 3

4 5 6

7 8

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Use the number buttons to quickly tune to any channel, even that was erased or not memorized.

CUSTOMIZING THE PICTURE

You can use the on-screen menus to adjust the brightness, contrast, filter, sharpness, color and tint according to personal

preference (each items(sub-menus) can be varied according to the input source.).

Alternatively, you can use one of the “automatic” settings. See next page.

Press the MENU button to display the menu

and select [picture] menu using or

button.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select a particular

item.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to change the value of

a particular item.

For example, if you select [contrast],

pressing increases it.

To adjust other items as desired, repeat the

above steps 1 to 3.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

USING AUTOMATIC PICTURE SETTINGS

Your TV has four automatic picture settings ("normal”, "movie", "sports" and "bright" ) that are preset at the factory. You

can activate each picture setting by pressing the P.MODE button.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

+100

SLEEP PRE.CH DISPLAY

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press the P.MODE button to select one of the

picture settings.

Choose “normal” for normal screen.

Choose “movie” to enjoy a movie as in a theater.

Choose “sports” to enjoy sports as in a stadium.

Choose “bright” for brighter screen.

CHANGING THE SCREEN SIZE

CHANGING THE SCREEN POSITION

You can change the screen size according to the program sources to be played back.

Press the P.SIZE button to select one of the screen

size settings.

Choose “normal” to set the picture to 4:3 normal

mode. This is a standard TV screen size.

Choose “wide” to set to 16:9 wide mode.

Choose “zoom” to magnify the size of the picture

on the screen.

Choose “video game zoom” to magnify the size of

the picture when enjoying a video game.

Choose “fill all” to view 4:3 programs in full

screen.

Choose “anamorphic” to view 2.35:1 anamorphic

DVDs in full screen

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

+100

SLEEP PRE.CH DISPLAY

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to display the menu

and select [window] - [h position] or [v

position] using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

The screen position can be changed also in other sources (TV, AV, etc.)

The on-screen displays disappear after several

seconds.

If this button is pressed when PC is selected for

signal source, TV will display the resolution

information.

VIEWING THE CURRENT STATUS

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

This function indentifies the current channel or the

status of certain audio-video conditions, etc.

Press the ENTER button on the remote control.

The TV will display the channel number, time

information, or audio-video conditions, etc.

Press or to adjust the position.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

CUSTOMIZING THE SOUND

The [treble], [bass] and [balance] can be adjusted to suit your personal preference.

These can be selected when the [surround mode] menu is set to “user”. Refer to next page.

Press the MENU button to display the menu

and select [audio] menu using or

buttons.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select a particular

item.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to change the value of

a particular item.

For example, if you select [treble], pressing

button increases it.

To adjust other items as desired, repeat the

above steps 2 and 3.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

SELECTING A SURROUND SOUND

Your TV has five automatic sound settings (“standard”, “music”, “movie”, “sports”, “news”, and “user”) that are preset

at the factory. You can activate any of them by making a selection from the on-screen menu).

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

Press the MENU button to display the menu

and select [audio] - [surround mode] menu

using /and /button.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select an

appropriate surround mode.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Choose “standard” for the standard factory

settings.

Choose “music” when watching music video or

concert.

Choose “movie” when watching movies.

Choose “sports” when watching sport games.

Choose “news” when watching news that is

mostly dialogue.

Choose “user” when adjusting audio items as you

want.

Press the SURR. button.

Each time this button is pressed, the surround mode

changes as follows:

standard music movie sports news

user standard

Quick way

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILDCHILD

LOCKLOCK

MUTE PIP SWAP SRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

+100

SLEEP PRE.CH DISPLAY

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

FINE TUNING CHANNELS

Use fine tuning to manually adjust a particular channel for optimal reception.

Generally, fine tuning is only necessary if reception is poor.

Press the MENU button to display the menu

and select [tv] - [fine tune] menu using /

and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to display the menu

and select [options] - [menu background]

menu using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Pressing or button changes the

caption background as follows:

opaque translucent

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

SELECTING THE BACKGROUND OF MENU

Special Features

Press ENTER or button.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to adjust the fine

tuning.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit .

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

LABELING THE CHANNEL NAME

You can label the channel name as you want.

At a particular channel, press the MENU

button to display the menu and select [tv] -

[edit labels] using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press ENTER or button to enter into sub

menu.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

FREEZING THE PICTURE

Press the MENU button to display the menu

and select [window] - [freeze window] menu

using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

At a particular scene, press or button

to select the “on”.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Then the moving image is freezed.

(Sournd is still heard.)

To cancel this function, repeat the above steps 1

and 2 to select the "off".

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press to move the cursor.

Repeat above steps 3 and 4 to fill another

characters.

It can be filled up to 5 characters.

To clear the channel name, press the

SOURCE button.

Press or button to select characters :

A~Z, a~z, 0 ~ 9, !, “, #, $, %, &, ‘, (, ), *,

+, ,, -, ., /, :, ;, <, =, >, ?, @, [, \, ], ^, _,

`,space

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

To label other channel names, repeat the

above the steps 1 to 4.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press the STILL button at a particular scene.

Press again to cancel.

Quick way

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

This function can zoom any picture on the screen and pan to 4 directions.

Press the MENU button to display the menu

and select [window] - [digital pan and zoom]

using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press ENTER or button to enter into sub

menu.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

DIGITAL PAN AND ZOOM

Zooming the Picture

Press the MENU button to display the menu

and select [window] - [digital pan and zoom]

using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press ENTER or button to enter into

zoom mode.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press repeatedly or hold down or

button to zoom the scene as you want.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Panning the Picture

Each time or button is pressed, the

picture is magnified as follows:

1.0 1.06 1.19 1.38 1.69

2.06 2.50 3.0 3.63 4.38

5.13 6.00 6.94 8.00

9.13 10.31 11.56 12.94

14.44 15.94

To pan the picture, perform the step 5 in

"Panning the Picture" procedure on page 39.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

Press ENTER button to change to pan mode

and then press // / button to move to

the part of scene.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Each time ENTER button is pressed, zoom mode

or pan mode is selected.

Press the MENU button repeatedly to exit.

You can make clearly sure of the zoom and pan functions when the picture is freezed in on-screen menu(refer to steps

1 to 3 in “FREEZING THE PICTURE” on page 36)

CHOOSING A MULTI-CHANNEL SOUND (MTS) SOUNDTRACK

Press the MTS I/II button.

Depending on the particular program being broadcast, you can listen to stereo, mono, or a foreign-language

translation.

Mono sound selection

In stereo reception if the stereo signal is weak,

you can switch to mono by pressing the MTS I/II

button. In mono reception the depth of sound is

improved. To switch back to stereo, press the

MTS I/II button again.

Language selection for dual language broadcast

If a program is received in two languages (dual

language), you can switch to DUAL I, DUAL II or

DUAL I+II by pressing the MTS I/II button

repeatedly.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

+100

SLEEP PRE.CH DISPLAY

SOURCE

STANDBY

REMOTE CONTROL RM-501

SETTING THE CLOCK

Setting the clock is neccessary in order to use the timer features of the TV.

Also, you can check the time while watching the TV. (Just press ENTER button.)

Press the MENU button to display the menu

and select [time] - [clock] menu using /

and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press button.

Then press or button repeatedly or

holding down either of these buttons until the

correct hour appears.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

After the hour is set, press button.

Then press or button repeatedly or

hold down either of these buttons until the

correct minutes appear.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

After the minutes are set,

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

SETTING THE ON/OFF TIMER

Press the MENU button to display the menu

and select [time] - [on time] menu using /

and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

2Press button.

Then press or button repeatedly or

hold down either of these buttons until the

correct hour appears.(i.e., the hour when the

TV will turn on.)

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

After the hour is set, press button.

Then press or button repeatedly or

hold down either of these buttons until the

correct minutes appear.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Setting the On Timer

Make sure the clock has been set correctly before setting the timer.

After the minutes are set, press button.

Then press or button to select on or

off.

When off is selected, the on timer is

deactivated.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press ENTER or button.

Then press or to select [channel]

menu.

Press or button repeatedly or hold

down either of these buttons until

appropriate channel is selected.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select [volume]

menu.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button repeatedly or hold

down either of these buttons until the volume

is adjusted as desired.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Setting the Off Timer

Press or button to select [off time]

menu.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Turn the power off before the on time.

At the on time, the power is turned on and

the timer function is activated automatically.

To operate the timer, you should turn the

power off before the on time

10 Press button.

Then press or button repeatedly or

hold down either of these buttons until the

correct hour appears.(i.e., the hour when the

TV will turn off.)

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

11 After the hour is set, press button.

Then press or button repeatedly or

hold down either of these buttons until the

correct minutes appear.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

After the minutes are set, press button.

Then press or button to select on or

off.

When off is selected, the off timer is

deactivated.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

SETTING THE SLEEP TIMER

The sleep timer automatically shuts off the TV after a preset time (from 10 to 240 minutes).

After several seconds, the sleep display disappears

from the screen, and the time interval is set.

POWER ON

PC AUTOPC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

1 2 3

4 5 6

+100

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the SLEEP button on the remote control

repeatedly until the appropriate time interval

appears.

To cancel the sleep timer, press the SLEEP button repeatedly until the “off” is displayed.

If the power turns off then on again, the sleep timer is canceled.

Quick way

Press the MENU button to display the menu

and select [time] - [sleep timer] menu using

/and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button until the appropriate

time interval appears (any of the preset

values from “off” to “ 240”).

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

This TV is equipped with an internal closed caption decoder. Closed caption is

a system which allows conversations, narration, and sound effects in TV

programs and home videos to be viewed as captions on the TV screen (see the

illustration).

Not all programs and videos will offer closed captioning.

Please look for the “ “ symbol to ensure that captions will be shown.

The closed caption broadcasts can be viewed in two modes: caption and text.

For each mode, two channels are available: cc1 / cc2, t1 / t2.

The caption mode shows subscripts of dialogs and commentaries of TV dramas and news programs while allowing a

clear view of the picture.

The text mode displays various information over the picture (such as TV program schedules and weather forecasts,

etc.) that is independent of the TV programs.

ADJUSTING CLOSED CAPTION SETTINGS

I like a carrot

Press the MENU button to display the menu

and select [settings] - [close caption mode]

menu using /and /buttons.

Pressing or button changes the

caption mode as follows:

cc1 cc2 t1 t2 xds* cc1

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Selecting the Kind of Closed Caption

*XDS : Extended Data Service.

This service displays "network name", "call

letter", "program name", "program length" and

"time in show" information, etc.

Press the MENU button to display the menu

and select [settings] - [close capt.

background] menu using /and /

buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Selecting the background of Closed Caption

Pressing or button changes the

caption background as follows:

opaque transparent

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Each time the CAPTION button is pressed, the

viewing mode(off / on / on mute) is changed.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Quick way

Closed caption may malfunction (white blocks, strange characters, etc.) if signal conditions are poor or if there are

problems at the broadcast source. This does not necessarily indicate a problem with your TV.

If any button is pressed to call up the on-screen menu while viewing a closed caption broadcast, the closed captions

will disappear momentarily.

If no text broadcast is being received while viewing in the text mode, the screen may become dark and blank for some

programs. Should this occur, switch the closed caption mode to off.

VIEWING CLOSED CAPTIONS

Press the MENU button to display the menu

and select [settings] - [close caption] menu

using /and /buttons.

Pressing or button to select viewing

mode as follows:

off on on mute

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

off : Closed caption does not display.

on : Closed caption displays.

on mute : If a broadcast contains closed

caption data and MUTE button is

pressed, the TV displays captions

automatically. Pressing MUTE

again will return the TV to its

previous condition.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

CHANGING WINDOW LAYOUT

Press the PIP button.

Each time this button is pressed, the picture layout

changes as follows:

PIP DW POP3 full screen PIP

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

VIEWING VARIOUS SOURCES SIMULTANEOUSLY

You can use this feature to simultaneously to watch two or more video sources.

Picture-In-Picture (PIP)

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Activating PIP

Selecting the one of two windows

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press the PIP button.

Press the WINDOW SEL. button.

Each time this button is pressed, the sub or main

window is selected.

In PIP or DW mode, the sound is heard from the

source of the window selected with WINDOW SEL.

button.

Selecting a signal source for PIP

Press the SRC button to select the source of sub

picture.

TV/S-VIDEO/AV/DVD can be selected for signal

source of sub picture.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOWWINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the SOURCE button to select the source of

main picture.

PC/DTV can be selected for signal source of main

picture.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOWWINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

If you want to change channels when TV is selected

for the signal source of sub picture, select the sub

window with WINDOW SEL. button and press CH +/-.

Changing size of Sub window

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to change the size of

PIP window.

Press the MENU button to display the menu

and select [window] - [pip size] menu using

/and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

[pip size] menu is displayed only in the PIP mode.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

Changing position of Sub window

Press the MENU button in PIP mode to

display the menu and select [window] - [pip

position] using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or to select one of five locations

as follows:

Whenever you select, the sub window

changes it’s position.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

Double Window (DW)

Press the PIP button repeatedly until the windows are

displayed as follows:

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Activating DW

#1 #2

Each time the SWAP button is pressed, the position

of the two windows is changed.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOWWINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Swapping the two windows

#1 #2 #2 #1

Selecting a signal source for DW

Press the SRC button to select the source of window

#2.

TV/S-VIDEO/AV/DVD can be selected for signal

source of this window.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOWWINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the SOURCE button to select the source of

window #1.

PC/DTV can be selected for signal source of this

window.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOWWINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

If you want to change channels when TV is selected

for the input signal source of window #2, select that

window with WINDOW SEL. button and press CH +/-.

Selecting the one of two windows

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press the WINDOW SEL. button.

Each time this button is pressed, the window #1

or #2 is selected.

Picture Off Picture (POP3)

Press the PIP button repeatedly until the windows are

displayed as follows:

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Activating POP3

Selecting the one of four windows

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press the WINDOW SEL. button.

Each time this button is pressed, the window

#1/#2/#3/#4 is selected in sequence.

The sound of POP3 follows that of window #1.

Selecting a signal source for POP3

Press the SRC button to select the signal source of

the window #2, #3 or #4 selected by pressing the

WINDOW SEL. button.

TV/S-VIDEO/AV/DVD can be selected for signal

source of the selected window.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOWWINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the SOURCE button to select the source of

window #1.

PC/DTV can be selected for signal source of this

window.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

WINDOWWINDOW

SEL.

PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

If you want to change channels when TV is selected

for the signal source of window #2(or #3/#4), select

that window with WINDOW SEL. button and press CH

+/-.

Press the MENU button to display the menu

and select [settings] - [content blocking]

menu using /and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Entering A Password

BLOCKING THE CONTENTS

The Parental Control function (V-Chip) is used to block TV programs viewing based on the ratings

sent by the broadcast station. The default setting is to allow all programs to be viewed. Viewing can

be blocked by the type of program and by the categories chosen to be blocked.

Restriction of TV programs include two ratings that contain information about the program: the MPAA

rating and the TV Parental Guidelines. The MPAA rating is restricted by age. TV Parental Guidelines

are restricted by age and content.

To use the Parental Control function, you should first enter a password and set the parental ratings.

Since a TV program may use either the MPAA ratings or the TV Parental Guidelines, both should be

adjusted for completed control.

MPAA ratings

G: General audience (no restrictions).

PG: Parental guidance suggested.

PG-13: PG-13 (Parents strongly cautioned).

R: Restricted (Children under 17 should be accompanied by an adult).

NC-17: No children under age 17.

X: Adults only.

NR: No rated.

The MPAA rating is only age-based.

TV Parental Guidelines

TV Parental Guidelines consist of the age-based categories and the content categories as follows.

Content categories

FV: Fantasy violence.

D: Sexual suggestive dialog.

L: Adult language.

S: Sexual situation.

V: Violence

Age-based categories

Y: Young children.

Y7: Children 7 and over.

G: General audience.

PG: Parental guidance.

14: Viewers 14 and over.

MA: Mature audience.

These categories consist of two separate

groups:"Y" and "Y7"(young children through

age7), and "G" through "MA"(everybody else).

Press button to select [enter].

Then press button to enter the password

entry mode.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press button to move the cursor to the

desired digit and press or button to

select the desired number (0~9).

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press ENTER or button.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Repeat the above step 4 to enter 6 digit password.

When you enter a password first time, enter "000000"

as default settings.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to exit from the

password entry mode.

Press the MENU button repetedly to exit from the on-

screen menu mode.

Press button to select "OK" and press

ENTER button.

If the correct password is entered, [enter] as

well as [change] are displayed.

If the password is not correctly, [change]

are not displayed. In this case, perform the

above step 4 to enter a password again.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Changing The Password

Before changing the passwond, you should enter the old password first, performing the steps 1~ 5 in

"Entering A Password" on the previous page.

Press button to select [change].

Then press button to enter the new

password entry mode.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press button to move the cursor to the

desired digit and press or button to

select the desired number (0~9).

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Repeat the above step 2 to enter a new 6 digit

password.

Press button to select "OK" and press

ENTER button.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Once the new password is changed into, do not

forget it. If you do not know it, you cannot set the

parental ratings. Should this happen, reset all the

settings made in the menus and enter "000000"

as password. (See "FACTORY RESET" on page

59)

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to exit from the new

password entry mode.

Press the MENU button repetedly to exit from the

on-screen menu mode.

Setting The Restrictions Using MPAA Ratings

Before setting this restrictions, you should enter the password first, performing the steps 1~ 6 in "Entering A

Password" on page 53.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select [movie

blocking].

Press or button to select a particular

MPAA category to be blocked and press the

ENTER button.

Each time the ENTER button is pressed at a

category, that category will be blocked or

not.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to exit from the

movie blocking mode.

Press the MENU button repeatedly to exit

from the on-screen menu mode.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Example 1: If "PG-13" is blocked, this will also

automatically block the higher

ratings "R", "NC-17", "X" and “NR".

Example 2: If "R" is blocked, this will also

automatically block the higher

ratings "NC-17", "X", and "NR".

Setting The Restrictions Using TV Parental Guidelines

Before setting this restrictions, you should enter the password first, performing the steps 1~ 6 in "Entering A

Password" on page 53.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press or button to select [tv blocking].

Press /and /buttons to select a

particular age-based category to be blocked

and press the ENTER button.

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button to exit from the tv

blocking mode.

Press the MENU button repetedly to exit

from the on-screen menu mode.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press /and /buttons to select a

particular content category to be blocked

and press the ENTER button.

If "L" sub rating in "PG" is blocked, the "L" sub

ratings in "14" and "MA" will automatically be

blocked.

Each time the ENTER button is pressed at a

category, that category will be blocked or not.

Example : If "Y7" is blocked, this will also

automatically block the higher

ratings "G", "PG", "14" and "MA". (The

cotent categories ("D", "L", "S", "V")

work together similary.)

"Y7", "PG", "14" and "MA" have sub ratings as

additional options. Do the next step to select

the particular content category.

Each time the ENTER button is pressed at a

category, that category will be blocked or

not.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

CHILD LOCK

If you do not want your child(ren) to watch the TV when you’re out, we recommend this function.

Press the CHILD LOCK button.

"on" is displayed.

And without remote control, this TV cannot be

controlled with the buttons of top panel.

To cancel this function, press this button again.

"off" is displayed and the TV can be controlled with

both the buttons of top panel and remote control.

Press the MENU button to display the menu

and select [options] - [child lock] menu using

/and /buttons.

Press or button to select the “on”.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press the MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Then without remote control, this TV cannot be

controlled with the buttons of top panel.

To cancel this function, select the "off".

Then the TV can be coltrolled with both the buttons

of top panel and remote control.

Quick way

FACTORY RESET

You can reset all the settings made in the menus to the default settings.

Press the MENU button to display the menu

and select [options] - [factory reset] using /

and /buttons.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press ENTER or button to enter into sub

menu.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Then all the settings are reset to the default

settings.

USING YOUR TV AS A COMPUTER (PC) DISPLAY

How to Connect Your PC to the TV

Selecting the PC signal input

Press the SOURCE button to select the PC

mode.

If the [source select] menu is set to “auto”,

each time this button is pressed, your TV

searches and detects the PC signal

automatically.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILDCHILD

LOCKLOCK

WINDOWWINDOW

SEL.SEL.

PIPPIP SWSWAPAP SRCSRC

ADD/ADD/

ERASEERASE CAPTIONCAPTION STILLSTILL

123

456

SLEEP PRE.CH AUTOSET

MENU MUTE

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Press PC AUTO button.

The picture is automatically centered on the

screen.

POWER ON

PC AUTOPC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

1 2 3

4 5 6

+100

SLEEPSLEEP PRE.CHPRE.CH AUTOSETAUTOSET

SOURCE

STANDBY

REMOTE CONTROL RM-501

14V 60W VIDEO

S-VIDEO

AUDIO(ST)

PC IN

14V 60W VIDEO

S-VIDEO

AUDIO(ST)

PC IN

PC VIDEO OUT

PC AUDIO OUT

REAR PANEL of TV

PC video connection

PC audio connection

Aligning the picture on the center of screen

PC Display

Adjusting the Screen Quality

The purpose of picture quality adjustment is to remove or reduce picture noise.

After the noise has been reduced, re-adjust the picture so that it is aligned on the center of screen.

See "Aligning the picture on the center of screen" on page 60.

Press the MENU button to display the

menu and select [picture] using or

button.

Press or to select [phase] for

horizontal stripes or [frequency] for vertical

ones.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

7 8

SLEEP PRE.CH DISPLAY

MENUMENU MUTEMUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Mode Resolution Vertical Horizontal

Frequency(Hz) Frequency (KHz)

VGA 640 X 480 60 31.4

640 X 480 67 35

640 X 480 75 37.5

640 X 480 85 43.2

SVGA 800 X 600 56 35.1

(MAC) 800 X 600 60 37.8

800 X 600 85 53.6

832 X 624 75 49.7

XGA 1024 X 768 60 48.3

1024 X 768 70 56.4

1024 X 768 75 60

1024 X 768 85 68.6

WXGA 1280 X 768 60 47.7

SXGA 1280X1024 60 64

How to Set up Your PC Display

Your PC display must be set as supportable format of this unit.

The displayable monitor specification is shown below:

If possible, use 1280 X 768 @ 60Hz

video mode to obtain the best image

quality for your LCD monitor. If used

under the other resolutions, some

scaled or processed pictures may

appear on the screen.

If the message “out of range” appears

on the screen, adjust the PC as in the

left table.

1280X768 @ 60 Hz video mode may not

be displayed well at certain video

card.

Press or to adjust the selected

item.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

456

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Press MENU button repeatedly to exit.

POWER ON

PC AUTO

ENTER

VOL VOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

4 5 6

7 8

SLEEP PRE.CH DISPLAY

MENU MUTE

SOURCE

STANDBY

REMOTE CONTROL RM-501

Changing the Screen Position

Changing the Screen Size

Press the P.SIZE button to select one of the screen

size settings.

Choose “fill all” to view the PC’s video signal in

full screen.

Choose “fill aspect” to view the PC’s video signal

in it’s original aspect fitted to TV’s screen size.

Choose “fill 1:1” to view the PC’s video signal in

it’s original size.

POWER ON

PC AUTO

ENTERENTER

VOLVOL VOLVOL

CHILD

LOCK

MUTE PIP SWAP SRC

ADD/

ERASE CAPTION STILL

123

+100

SLEEP PRE.CH DISPLAY

SOURCESOURCE

STANDBY

REMOTE CONTROL RM-501

Follows the steps 1 to 3 in “CHANGING THE SCREEN POSITION” on page 30.

Troubleshooting

If the TV seems to have a problem, first try this list of possible problems and solutions.

If none of these troubleshooting tips apply, call your nearest service center.

Problem Possible Solution

Poor picture Try another channel.

Adjust the antenna.

Check all wire connections.

Poor sound quality Try another channel.

Adjust the antenna.

No picture or sound Try another channel.

Press some buttons related to audio/video .

Make sure the TV is plugged in.

Check the antenna connections.

Ensure that the signal cable is firmly connected to the PC or video sources.

Ensure that the PC or video sources are turned on.

No color, wrong colors or tints Make sure the program is broadcasted in color.

Adjust the picture settings.

If the set is moved or turned in a different direction, the power should be OFF

for at least 30 minutes.

Adjust antenna.

Picture rolls vertically. Check all wire connections.

The TV operates erratically. Unplug the TV for 30 seconds, then try operating it again.

The TV won’t turn on. Make sure the wall outlet is working.

Blurred or snowy picture, Check the direction, location and connections of your aerial.

distorted sound This interference is often due to the use of an indoor aerial.

Remote control malfunctions Replace the remote control batteries.

Aim correctly to remote sensor.

Check the battery terminals.

“out of range” message Check the maximum resolution and the frequency of the display.

The image is too light or too dark Adjust the brightness and contrast.

Adjust the fine tuning.

Horizontal bars appear to flicker, Adjust the fine tuning.

jitter or shimmer on the image

Vertical bars appear to flicker, The TV is using its power management system.

jitter or shimmer on the image Move the computer’s mouse or press a key on the keyboard.

Image is not centered on the screen Adjust the horizontal and vertical position.

RETRACTABLE STAND

CLEANING AND MAINTAINING YOUR TV

Appendix

The maximum tilt angle is 15 degrees in the backward

direction. Please do not tilt the TV outside the

specified range. Using excessive force to tilt the TV

may cause permanent damage to the mechanical part

of the stand.

Do not use the stand other than the one attached.

If other stand is used, this can cause the TV to fall,

resulting in serious personal injuries as well as damage

to the TV.

With proper care, your TV unit will give you many years of service. Please follow these guidelines to get the maximum

performance from your TV.

Placement

Do not place the TV near extremely hot, cold, humid or dusty places.

Do not place the TV near appliances with electric motors that create

magnetic fields, such as vacuum cleaners.

Keep the ventilation openings clear; do not place the TV on a soft surface,

such as cloth or paper.

Place the TV in a vertical position only.

Liquids

Do not handle liquids near or on the TV.

Liquids that spill into it can cause serious damage.

Cabinet

Never open the cabinet or touch the parts inside.

Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax,

or chemicals.

Do not put heavy objects on top of the cabinet.

Temperature

If your TV is suddenly moved from a cold to a warm place, unplug the power

cord, and allow at least two hours for moisture that may have formed inside

the unit to dry completely.

USING YOUR TV IN ANOTHER COUNTRY

If you plan to take your TV with you to a foreign country, please be aware of the different television systems

that are in use around the world. A TV designed for one system may not work properly with another system

due to differences in the TV channel frequencies.

LCD

The LCD panel used in this product is made of glass. Therefore, it can

break when the product is dropped or applied with impact. Be careful not to

be injured by broken glass pieces in case the LCD panel breaks.

The LCD panel is a very high technology product with thin film transistors,

giving you fine picture details.

Occasionally, a few non-active pixels may appear on the screen as a fixed

point of blue, green or red. Please note that this does not affect the

performance of your product.

NOTES

This product incorporates copyright protection technology that is protected

by U.S. patents and other intellectual property rights. Use of this copyright

protection technology must be authorized by Macrovision, and is intended

for home and other limited viewing uses only unless otherwise authorized by

Macrovision. Reverse engineering or disassembly is prohibited.

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION

TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT

AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN

CASE OF 525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS

RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE

'STANDARD DEFINITION' OUTPUT. IF THERE ARE QUESTIONS

REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p

DVD PLAYER, PLEASE CONTACT OUT CUSTOMER SERVICE CENTER.

Panel Display Size 17.1inch(434.38 mm, diagonal)

Actual Display Sizel 372.48(H) X 223.488(V) mm

Pixel Size 0.291 X 0.291 mm

viewing Angle 88 / 88 / 88 / 88 (L / R / U / D)

Frequency Horizontal 30 ~ 64 KHz

Vertical 50 ~ 85 Hz

Display Color 16.777.216 colors

Display Optimum Mode 1280 X 768 @ 60

Resolution Maximum Mode 1280 X 1024 @ 60 Hz

Input Signal Sync. H/V Separate, TTL, SOG (Sync On Green)

Video signal 0.7 VP-P@ 75 Ohm

Video Color system NTSC

Video system CVBS, S-VHS, COMPONENT

Component Video In 1.0 VP-P@75 ohm

Audio In 300 mVrms

Power Supply Input AC 100 ~240 V, 50/60 Hz, 1.8 ~ 0.9 A

Output DC 14 V , 4.5 A

Power Maximum 63 W

Consumption Power Saving < 10 W

Dimensions/ Unit(WxDxH):

Weight TV body 22.06 X 2.6 X 11.43 inch / 13.45 lbs

(560 X 66 X 290 mm / 6.1 kg)

With stand 22.06 X 7.88 X 14.81 inch / 15.44 lbs

(560 X 200 X 376 mm / 7 kg)

Environmental Operating 32 F to 122 F (0 C to 50 C)

Considerations Temperature

Operating 10 % to 90 %

Humidity

Storage -4 F to 140 F (-20 C to 60 C)

Temperature

Storage 10 % to 90 %

Humidity

Audio Audio Input RCA Jack Red(R) White(L), 0.3 Vrms

Characteristics Stereo out Max. 4.0 W output

Headphone out Max. 10 mW Output

Specifications

Design and specifications are subject to change without notice for improvements.

Inkel ETR0004 TFT LCD TV MONITOR User Manual USERS MANUAL

INKEL Corporation TFT LCD TV MONITOR USERS MANUAL

USERS MANUAL

Navigation menu

Namespaces

Views

Navigation