Inkel MB8811C1 Bluetooth Module User Manual

Inkel Corporation Bluetooth Module

User Manual

Operating Instructions Copyright 2017 by INKEL Bluetooth Module for Audio Bluetooth Module Model: MB8811C1 Operating Instructions OEM/Integrators Installation Manual
Operating Instructions 1 Copyright 2017 by INKEL General Description MB8811C1 is a fully integrated Bluetooth module. It is based on CSR’s Bluecore 8811 chip with specific interface design to meet Inkel Corporation’s needs. MB8811C1 is compatible with Bluetooth specification version 4.0. It integrates RF, Baseband controller, etc., a completed Bluetooth subsystem. Features - Dual-mode Bluetooth / Bluetooth low energy radio - Stereo codec with 2 microphone inputs - Fast Charging support up to 200mA with no external components - Multipoint support for A2DP connection to 2 A2DP source for music playback - aptX, SBC, MP3, AAC and Fast stream decoder - Built-in Reference Clock: 26MHz - RoHS Compliant Applications - Stereo headsets - Wired stereo headset and headphones - Portable stereo speakers - Audio Products Pattern Antenna - Frequency Range : 2400 ~ 2500 MHz - Peak Gain(MAX) : 1.396 dBi Device Overview
Operating Instructions 2 Copyright 2017 by INKEL Dimensions
Operating Instructions 3 Copyright 2017 by INKEL Block Diagram
Operating Instructions 4 Copyright 2017 by INKEL Pin Descriptions
Operating Instructions 5 Copyright 2017 by INKEL Example Application schematic Electrical Characteristics
Operating Instructions 6 Copyright 2017 by INKEL
Operating Instructions 7 Copyright 2017 by INKEL Module’s Label Information Inkel Corporation FCC ID: VNH-XXXXXXXXXX IC: XXXX-XXXXXXXXXX CMIIT ID: XXXXXXXXX XXX-XXXXX
Operating Instructions 8 Copyright 2017 by INKEL RegulatoryUSA The MB8811C1 module has been labeled with its own FCC ID number, and if the FCC ID is not visible when the module is installed inside host audio device. Then the outside of the finished product into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording as follows: This device complies with Part 15 of the FCC Rules. Operation is subject the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, And (2) this device must accept any interference received, including interference that may cause undesired operation A user’s manual for the product should include the following statement NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.FCC Information to UserThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.• Consult the dealer or an experienced radio/TV technician for help.
Operating Instructions 9 Copyright 2017 by INKEL CANADA The MB8811C1 module has been labeled with its own IC number, and if the IC is notvisible when the module is installed inside host audio device. Then the outside of the finished product into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording as follows: A user’s manual for the product should include the following statement EUROPE Hereby declares that this Bluetooth module is in compliance with the essential requirements and other relevant provisions of R&TTE Directive 1999/5/EC. The standards for complying are as following: ETSI EN 301 489-1 V1.9.2: 2011-09 ETSI EN 301 489-17 V2.2.1: 2012-09 ETSI EN 300 328 V1.9.1:2012-06 EN 62479: 2010 EN 60065:2002 + A1:2006 + A11:2008 + A2:2010+A12:2011
Operating Instructions 10 Copyright 2017 by INKEL This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device is intended for home and office use in all EU countries KOREA KC TAIWAN
Operating Instructions 11 Copyright 2017 by INKEL Manufacturer: Inkel Corporation 93, Cheongjung-ro, Bupyeong-Gu, Incheon, 403-853, Republic of Korea Tel: 82-032-650-6000 Manual Information To the End UserThe OEM integrator has to be aware not to provide information to the end userregarding how to install or remove this RF module in the user’s manual of theend product which integrates this module.The end user manual shall include all required regulatory information/warningas show in this manual.IMPORTANT NOTE: that the module is limited to installation in mobile or fixed applications, If it is infringe then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.This transmitter must not be co-located or operating in conjunction with anyother antenna or transmitter.End Product LabelingThe final end product must be labeled in a visible area with the following: “Contains FCC ID:VNH-MB8811C1”. The grantee's FCC ID can be used only when all FCC compliance requirements are met.Radiation Exposure Statement:The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.“Inkel Corporation will provide guidance to the host manufacturer for compliance issues with Part 15 Subpart B compliance if needed.”

Navigation menu