InnoComm Mobile Technology BM15-AN BT 4.0 single PCB module User Manual
InnoComm Mobile Technology Corporation BT 4.0 single PCB module Users Manual
Users Manual
BT4.1 LE Module User Manual Model name: BM15_AN Introduction This document describes Key feature, pin definition, mechanical drawing, Recommendation for PCB Layout and operation temperature and voltage range, and reflow data of Bluetooth Low Energy Module and it can helps designer to design in easier and manufacturing smoothly. BLE module Install Guide line Key Features RF • 2.4-GHz Bluetooth low energy Compliant and Proprietary RF Single Mode Module • Supports 250-kbps, 500-kbps, 1-Mbps, 2-Mbps Data Rates • Software programmable adjustable transmitter power (-20dBm to 5dBm) for short to long range applications • Suitable for Systems Targeting Compliance With Worldwide Radio Frequency Regulations: ETSI EN 300 328 and EN 300 440 Class 2 (Europe), FCC CFR47 Part 15 (US), and ARIB STD-T66 (Japan) Layout • Few External Components • 18.0 mm × 10.5 mm × 2.0 mm, 26 pin LCC Package Low Power • Wide supply voltage range : 1.9 – 3.8V • Differential RF mode : 6.4±3 mA • Differential RF mode TX at 0 dBm: 6.8±3 mA • Differential RF mode TX at +5 dBm: 8.9±3mA • Low Power Mode: 1 μA (RTC Running + RAM/CPU retention) • Low Power Mode: 100 nA (Flash retention) • Optional on-chip DC/DC converter (not available in 1.8V mode) Peripherals • Integrated temperature sensor • 4 General-purpose Timer Modules (8x 16-bit or 4x 32 bit-timer, PWM each) • 12-bit ADC, 200 ksamples/s, 8 channel analog MUX • Ultra-low-power analog comparator • UART • 2x SPI • Ultra-low power • I2C, I2S • Real-time clock • AES-128 security module • Support for 8 capacitive sensing channels Application Profile • Consumer electronics • Mobile phone accessories • Sports & Fitness equipment • HID applications • Home and Building Automation • Lighting Control • Alarm and Security • Electronic Shelf Labeling • Proximity Tags • Medical • Remote Controls • Wireless Sensor Networks Mechanical Drawing Module Pin Definition Pin # Pin Name Direction/Type Power Description GND Ground DIO_0 Digital I/O GPIO, ULP Sensor Interface DIO_1 Digital I/O GPIO, ULP Sensor Interface DIO_2 Digital I/O GPIO, ULP Sensor Interface, LED driving capability DIO_3 Digital I/O GPIO, ULP Sensor Interface, LED driving capability DIO_4 Digital I/O GPIO, ULP Sensor Interface, LED driving capability JTAG_TMSC Digital I/O JTAG TMSC, LED driving capability JTAG_TCKC Digital I/O JTAG_TCKC JTAG_TDO Digital I/O GPIO, LED driving capability, JTAG_TDO 10 JTAG_TDI Digital I/O GPIO, LED driving capability, JTAG_TDI 11 GND Power Ground 12 GND Power Ground 13 nRESET 14 Digital In Reset, active-low. No internal pull-up DIO_7 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 15 DIO_8 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 16 DIO_9 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 17 DIO_10 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 18 DIO_11 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 19 DIO_12 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 20 DIO_13 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 21 DIO_14 Digital/Analog I/O GPIO, ULP Sensor Interface, Analog 22 VDD Power 1.9V to 3.8V main chip supply 23 GND Power Ground 24 GND Power Ground 25 GND Power Ground 26 GND Power Ground Reference Circuit for User design Recommended: Operating Range over operating free-air temperature range (unless otherwise noted) MIN NOM MAX Operating ambient temperature range, TA Operating supply voltage –40 1.9 Recommendation: PCB Layout for User design UNIT 85 °C 3.8 Reflow data Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The product can be kept as far as possible from the user body or set the device to lower output power if such function is available. The final end product must be labeled in a visible area with the following: “Contains FCC ID: YAIBM15-AN”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Warning : Invalid xref tableEXIF Metadata provided by EXIF.tools