InnoSenT IPM165F K-Band Transceiver Module User Manual IPM 165 F

Download:
Mirror Download [FCC.gov]
Document ID	1166352
Application ID	GJP6PNG7BBQDW2COXz5oLg==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	27.52kB (344031 bits)
Date Submitted	2009-09-09 00:00:00
Date Available	2009-09-09 00:00:00
Creation Date	2009-08-21 11:16:53
Producing Software	GNU Ghostscript 7.06
Document Lastmod	2009-08-21 11:16:53
Document Title	User manual IPM-165_F
Document Creator	PDFCreator Version 0.8.0
Document Author:	zirk_andreas

User Manual
Product Family: K-Band Transceivers
K-Band Transceiver
with two integrated patch antennas
IPM-165 (and variants IPM-165_UK / IPM-165_F)
Description:
radar-based motion detector
available in different frequency ranges:
Standard; _F and _UK variants
Standard version selected by signal level
advanced PHEMT-oscillator with low current consumption
split transmit and receive path for maximum gain
mono (single channel) operation
very small outline dimensions
Environmental Tests and Handling Precautions:
This InnoSenT Sensor is sensitive to damage from ESD.
Normal precautions as usually applied to CMOS devices are sufficient when handling the
device. Touching the signal output pins has to be avoided at any time before soldering or
plugging the device into a motherboard.
Applying multimeters e.g. for resistance measurement between any of the connector pins
may cause damage to the module.
Absolute Maximum Ratings:
Parameter
supply voltage
operating temperature (out of spec)
storage temperature
Symbol
VCC
TOP
TSTG
Rating
5.25
- 40 / + 85
+ 90
Units
°C
°C
Electrical Characteristics:
Parameter
transmit frequency
Symbol
min.
typ.
max.
units
comment
fStandard
24.000 24.125 24.250
GHz
fIPM-165_UK
24.150 24.200 24.250
GHz
fIPM-165_F
24.075 24.125 24.175
GHz
output power (EIRP)
Pout
16
dBm
temperature drift
-1
MHz/°C
∆f
antenna pattern Tx (3dB) horizontal
80
°
azimuth
vertical
32
°
elevation
side lobe suppression
horizontal
13
dB
azimuth
vertical
13
dB
elevation
IF output
voltage offset
-300
300
mV
signal level*
category A (low)
263
399
mVP-P
category B or E
400
549
mVP-P
(medium)
category C(high)
550
850
mVP-P
supply voltage
VCC
4.75
5.0
5.25
supply current
ICC
30
40
mA
Pulse length
tpulse
10
µs
operating temperature
TOP
- 20
+ 60
°C
outline dimensions
~ 25 x 25 x 7 (12.7)
mm
compare drawing
*Relative output signal level/voltage measured at room temperature in a dedicated InnoSenT test setup.
Version 7.4
2008-04-23
IPM-165
page 1 of 3
Interface:
The sensor provides a 2.54mm grid, single row pin header (square pin 0.635mm)
Pin #
Description
VCC
IF1
GND
In/Out
input
output
input
Comment
supply voltage (+5 V)
signal output
analog ground
Mechanical Outlines:
(all dimensions in mm)
Approved pulsing conditions to fulfill the FCC requieremts:
•
ASK modulation with 10kHz and 10% dutycycle (on-time 10µs min.)
•
Warning: Any other pulsing condition with less than 10µs on-time may void the FCC authorization to operate
this equipment.
Certification and environment protection:
InnoSenT GmbH has established and applies a quality system for:
Development, production and sales of radar sensors for commercial and
industrial sensors
An audit was performed, Report No. 010350 Proof has been furnished that
the requirements according to DIN EN ISO 9001:2000 are fulfilled.
This InnoSenT product is compliant to the restriction of hazardous substances
(RoHs – European Union directive 2002/95/EG).
Version 7.4
2008-04-23
IPM-165
page 2 of 3
FCC approval
•
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
•
Warning: Changes or modifications made to this equipment not expressly approved by InnoSenT GmbH may
void the FCC authorization to operate this equipment.
•
Manufacturers of mobile or fixed devices incorporating IPM-165 modules are authorized to use the FCC
Grants and IC Certificates of the IPM-165 modules for their own final products according to the conditions
referenced in these documents. In this case, the FCC label of the module shall be visible from the outside, or
the host device shall bear a second label stating "Contains FCC ID: UXS-IPM165F" and "Contains IC:
4012A-IPM165F".
Contact Information:
InnoSenT GmbH
Am Roedertor 30
97499 Donnersdorf
Germany
Version 7.4
2008-04-23
Phone: +49 (0) 9528-9518-0
Fax:
+49 (0) 9528-9518-99
IPM-165
E-Mail: info@InnoSenT.de
Web:
www.InnoSenT.de
page 3 of 3

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 3
Producer                        : GNU Ghostscript 7.06
Title                           : User manual IPM-165_F
Creator                         : PDFCreator Version 0.8.0
Create Date                     : 2009:08:21 11:16:53
Author                          : zirk_andreas
Modify Date                     : 2009:08:21 11:16:53
Subject                         : 

EXIF Metadata provided by EXIF.tools