Innovative Wireless Technologies IWTBB1142 802.15.4 Transceiver User Manual CERTIFICATE OF COMPLIANCE

Innovative Wireless Technologies, Inc. 802.15.4 Transceiver CERTIFICATE OF COMPLIANCE

Users Manual Revised

Download: Innovative Wireless Technologies IWTBB1142 802.15.4 Transceiver User Manual CERTIFICATE OF COMPLIANCE
Mirror Download [FCC.gov]Innovative Wireless Technologies IWTBB1142 802.15.4 Transceiver User Manual CERTIFICATE OF COMPLIANCE
Document ID520722
Application IDaC2/NH11qcNuqJ409Tzt4A==
Document DescriptionUsers Manual Revised
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize37.02kB (462810 bits)
Date Submitted2005-03-06 00:00:00
Date Available2005-03-06 00:00:00
Creation Date2005-03-02 09:34:59
Producing SoftwareAcrobat Distiller 4.05 for Windows
Document Lastmod2005-03-02 09:35:34
Document TitleCERTIFICATE OF COMPLIANCE
Document CreatorMicrosoft Word 10.0
Document Author: Systems Administrator

Rhein Tech Laboratories
360 Herndon Parkway, Ste 1400
Herndon, VA 20170
http://www.rheintech.com
Client:
Model:
FCC ID:
Standard:
IWT
AXONTM Module
SP8-IWTBB1142
FCC 15.247
APPENDIX I: MANUAL
Please refer to the following pages.
Page 40 of 47
AXON™ USER MANUAL
© Copyright 2005 Innovative Wireless Technologies
P1b
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference
received, including interference that may cause
undesired operation.
FCC ID: SP8-IWTBB1142
IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna
used for this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Changes or modifications to this unit not expressly approved by Innovative Wireless
Technologies, Inc. could void the user’s authority to operate this equipment.
Innovative Wireless Technologies, Inc.
1047 Vista Park Drive, Suite A
Forest, Virginia 24551
1-434-316-5230 (United States)
www.iwtwireless.com (United States)
AXON™ and Synaptrix™ are registered in the US Patent & Trademark Office.
© Innovative Wireless Technologies, Inc. 2004, 2005
© Copyright 2005 Innovative Wireless Technologies
P1b
Axon™
Innovative Wireless Technologies
User Manual
802.15.4 Transceiver Module
Overview
IWT’s Module is a 2.4 GHz transceiver
module that offers an embedded 16-bit
RISC CPU and is designed to comply with
IEEE’s 802.15.4 physical layer
specifications. The module offers the user a
compact size, ruggedized connections, and
an on-board antenna. The module is
designed to work with your sensor
applications by offering UART
communications, 3 general-purpose I/O
ports, one 12-bit Analog-to-Digital port, and
a SPI compatible interface to operate a
peripheral device. The module also offers a
6MHz and a 32.768kHz watch crystal for
your timing needs.
The AXON™ Module is Synaptrix™ ready
and ZigBee™ ready. Synaptrix™ is IWT’s
mesh-networking software stack.
Interfaced to the programmer board, the
module offers a practical design
environment that allows for fast debug and
easy access to the programmable
interfaces.
Figure 1 - Axon module with programming board
© Copyright 2005 Innovative Wireless Technologies
P1b
FCC Statement for OEM Integrators
AXON™ Module Use for maintaining RF exposure
This device is intended only for OEM integrators under the following conditions:
1. Connection to the AXON™ Module should always be made through the 20 pin header.
Connection to the AXON™ Module any other way not expressed in this documentation or
approved by Innovative Wireless Technologies, Inc. will void the user’s ability to operate this
device under the FCC certification.
The header on the AXON™ Module is a SAMTEC FTMH-110-02-L-DH, and mate connection is
CLM-110-02-L-D.
2. The AXON™ Module may not be co-located with any other transmitter or antenna.
3. The AXON™ Module is approved using the FCC “Unlicensed modular transmitter
approval” method. Therefore the AXON™ Module must only be used with the originally
approved antenna(s).
As long as the 3 conditions above are met, further transmitter testing will not be required.
However, the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain, colocation with another transmitter, or different antenna), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances,
the OEM integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
OEM End Product Labeling
The final end product that has integrated the AXON™ Module must be labeled in a visible area
with the following: Contains TX FCC ID: SP8-IWTBB1142
IMPORTANT NOTE TO OEM
The end user of the OEM’s product, with incorporated AXON™ Module, should NOT be provided
any instructions on how to remove or install the AXON™ Module.
© Copyright 2005 Innovative Wireless Technologies
P1b
The AXON™ Module Interface (Getting Started)
Voltage must be supplied to the AXON™ Module via pins 19 and 20 on the interface header. The
AXON™ Module regulates its voltage on board, but must be supplied a voltage between 3.3-6
Volts. The table below outlines the 20 pin interface to the AXON™ Module. The mechanical
diagram that follows indicates where pin-1 starts.
Connector
Pin out
11
13
15
17
19
TP
Name
TDI/TDO
TDI
TMS
TCK
GND
RESET
SPI_CLK
GPIO5
A0
GND
Connector
Pin out
10
12
14
16
18
20
TP
Name
SPI_CS
IWT
UART_Data_uP
UART_Data_PC
SPI_SIMO
SPI_SOMI
GPIO3
GPIO4
IWT
V_Batt
Once power is applied to pins 19 and 20, primary communication through the AXON™ Module
will take place on pins 6 and 8. These pins are the buffered UART interface to the Module. This
UART interface is 3.3-Volt logic only. To communicate with a PC and RS232 Translator must be
used on the customer’s end device. The AXON™ Programmer Board, used for prototype
development, translates the UART signaling to PC levels. Innovative Wireless Technologies’
document “AXON™-Synaptrix™ Network Interface Specification” outlines the communication
protocol utilized on the UART plus the over the air communication protocols for your peer-to-peer
and mesh network configurations.
Once the UART link has been correctly initialized, your device can then utilize the AXON™
Module to communicated information wirelessly to other AXON™ Modules. This allows the end
user to quickly setup communication links between two or multiple devices. If communication
becomes inoperable, momentarily pulling pin 11 (RESET) low, 0-Volts, will reset the AXON™
Module.
© Copyright 2005 Innovative Wireless Technologies
P1b
AXON™ Module Electrical Specifications
Parameter
Min.
Operation Temperature
-40
RF Frequency Range
Absolute Supply Voltage
Transmit Bit Rate
Transmit Chip Rate
Nominal Output Power
2400
3.3
Transmitter
250
2000
Max.
Unit
85
ºC
2483.5
+6
MHz
250
2000
kbps
kChips/s
Receiver
Receiver Sensitivity
-90
Dynamic Range
Frequency Error Tolerance
Typ.
Overall
dBm
-94
90
-300
General I/O Available
dBm
300
GPIO3-5
SCHMITT-Trigger Input Specifications
VIT+ Positive-going input threshold
1.5
1.9
VIT- Negative-going input
threshold
0.9
1.3
Vhys Input voltage hysteresis
0.5
1.0
Output Specifications
VOH High-level output voltage
Test Condition IOH(max) = -1mA
Vcc-0.25
Vcc
Test Condition IOH(max) = -6 mA
Vcc-0.60
Vcc
VOL Low-level output voltage
Test Condition IOL(max) = 1.5 mA
Vss
Vss+0.25
Test Condition IOL(max) = 6 mA
Vss
Vss+0.6
Analog to Digital Inputs Available
A0
Accuracy
12
Input capacitance
140
Input resistance
2050
External Voltage Reference (selectable
via resistor divider)
1.4
3.3
Current Consumptions
Transmit Mode
19
Receive Mode
21
Idle Mode
Sleep Mode
© Copyright 2005 Innovative Wireless Technologies
dB
kHz
Condition/Note
Ambient
Temperature
Programmable in 1
MHz steps. 5 MHz
steps needed for
compliance with
802.15.4
802.15.4/D18
802.15.4/D18
Delivered into 50
load
PER=1%, Measured
through 50 load,
conducted.
PER=1%, Measured
through 50 load,
conducted.
Bit
pF
12 bit ADC
mA
mA
470
uA
140
uA
Measured at 4.5 V
(3-AA supply)
Measured at 4.5 V
Measured at 4.5 V
(OSC and UART
running)
Measured at 4.5 V
(No OSC or
UART)
P1b
Mechanical Board Dimensions
Figure 2 Module Dimensions (mils)
© Copyright 2005 Innovative Wireless Technologies
P1b
Innovative Wireless Technologies
1047 Vista Park Drive
Suite A
Forest VA 24551
434-316-5230
© Copyright 2005 Innovative Wireless Technologies
P1b

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2005:03:02 09:35:34-07:00
Create Date                     : 2005:03:02 09:34:59-07:00
Title                           : CERTIFICATE OF COMPLIANCE
Author                          : Systems Administrator
Creator                         : Microsoft Word 10.0
Producer                        : Acrobat Distiller 4.05 for Windows
Page Count                      : 9
EXIF Metadata provided by EXIF.tools
FCC ID Filing: SP8-IWTBB1142

Navigation menu