Innovative Wireless Technologies SBB0100-010-1 Battery powered radio used in a mesh network of unattended sensors User Manual CERTIFICATE OF COMPLIANCE
Innovative Wireless Technologies, Inc. Battery powered radio used in a mesh network of unattended sensors CERTIFICATE OF COMPLIANCE
User Manual Revised
Rhein Tech Laboratories, Inc. Client: IWT
360 Herndon Parkway Model #: SBB0100-010-R4G
Suite 1400 Standards: FCC 15.247/RSS-210
Herndon, VA 20170 FCC ID: SP8-SBB0100-010-1
http://www.rheintech.com Report #: 2012045
Page 47 of 55
Appendix M: User Manual
Please refer to the following pages.
FOR OFFICIAL USE ONLY 1
User Guide: mProm Module
Prepared by:
Innovative Wireless Technologies, Inc.
Forest, Virginia
Document # 7720-12-0547 Rev A
FOR OFFICIAL USE ONLY 2
Table of Contents
FCC STATEMENT .................................................................................................................. 3
1. MPROM SUMMARY ........................................................................................................ 3
2. MPROM CONTROL ......................................................................................................... 3
3. SAFEY PRECAUTIONS .................................................................................................. 3
4. REVISION HISTORY ....................................................................................................... 4
FOR OFFICIAL USE ONLY 3
FCC Statement
Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV technician for help.
1. mProm Summary
The mProm™ mesh radio SBB0100-010-R4G is a battery-powered transceiver designed specifically for use in a
mesh network, particularly low power sensors. In normal operation these radios are autonomous and scattered
throughout a locality and serve as the communications backbone infrastructure for deployed assets. The radios
operate with no direct physical user interface after power-on.
2. mProm Control
IWT maintains complete control over the mProm module and any and all end products into which it is installed.
3. Safey Precautions
This section contains details on the safety precautions of the mProm module.
Warning: Only trained personnel should be allowed to install, replace, or service this equipment.
Warning: Do not locate the antenna or cables where they may accidentally contact overhead electrical
wires.
Warning: Do not work on the device or connect or disconnect cables during periods of lightning activity.
FOR OFFICIAL USE ONLY 4
IMPORTANT NOTE: The antenna must be installed 20 cm or more from any personnel in order to comply
with FCC RF exposure requirements. When using a 9 dBi gain 900 MHz antenna, this distance should be
increased to 40 cm in order to assure compliance with RF exposure requirements applicable to the general
public. Brief exposure at 20 cm or greater is within occupational exposure limits.
4. Revision History
Revision
Date
Changes
Author
A
12/4/12
Release
J. Colling
B
12/13/12
Revision to include Safety Precautions
J. Colling