Innovative Wireless Technologies TB100001 Fixed Tracking Beacon User Manual CERTIFICATE OF COMPLIANCE
Innovative Wireless Technologies, Inc Fixed Tracking Beacon CERTIFICATE OF COMPLIANCE
User Manual
Rhein Tech Laboratories, Inc.
Client:
L3 Communications
360 Herndon Parkway
Model #:
FAP5010-001
Suite 1400
Standards:
FCC 15.247
Herndon, VA 20170
http://www.rheintech.com
FCC ID:
XG8-TB100001
Report #:
2009239
Page 27 of 33
Appendix H: Manual
Please refer to the following pages.
Page 1 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
INSTALLATION AND USER’S GUIDE
FOR
FIXED TRACKING BEACON
FAP5010-001
Innovative Wireless Technologies, Inc.
1047 Vista Park Drive, Suite A
Forest, VA 24551
Phone: (434)316-5230
Fax: (434)316-5232
www.iwtwireless.com
Page 2 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
Contents
1. PRODUCT OVERVIEW.................................................................................................... 3
2. SAFETY INFORMATION ................................................................................................ 3
3. SPECIFICATIONS FOR FAP5010-001 ............................................................................ 5
4. DESCRIPTION................................................................................................................... 6
4.1 OUTPUTS........................................................................................................................... 6
4.2 COMPONENTS NECESSARY FOR INSTALLATION .................................................. 6
5. PRIOR TO INSTALLATION ............................................................................................ 7
5.1 Site Survey .......................................................................................................................... 7
5.2 Visually inspect each Fixed Tracking Beacon to ensure that: ............................................ 7
6. INSTALLATION INSTRUCTIONS.................................................................................. 8
6.1 INSTALLATIONS BELOW GROUND............................................................................ 8
6.1.1 Antenna Placement ............................................................................................................. 8
6.1.2 Applying Power to the Fixed Tracking Beacon.................................................................. 8
6.1.3 Fixed Tracking Beacon Enclosure Placement .................................................................... 9
6.1.4 Fixed Tracking Beacon Antenna Connection ..................................................................... 9
6.2 INSTALLATIONS ABOVE GROUND ...........................Error! Bookmark not defined.
6.2.1 Fixed Tracking Beacon Installation Instructions ................................................................ 9
6.2.2 Follow all FCC guidelines listed in Section 2.0. ................................................................ 9
7. OPERATING AND MAINTENANCE INSTRUCTIONS ................................................ 9
Page 3 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
1. PRODUCT OVERVIEW
Innovative Wireless Technologies’ Fixed Tracking Beacon is a transmitter intended primarily for
use in industrial mining applications. The FAP5010-001 Fixed Tracking Beacon design
provides enhanced tracking for miners and equipment in high-traffic areas of a coal mine.
The Fixed Tracking Beacon is one component of a communication and tracking system that
includes the Innovative Wireless Technologies’ FAP4210-001 Fixed Mesh Node and FAP2210-
001 Gateway Node.
2. SAFETY INFORMATION
IMPORTANT INFORMATION ON SAFE OPERATION. READ THIS INFORMATION
BEFORE INSTALLING AND OPERATING THE FIXED TRACKING BEACON.
Changes or modifications to this unit not expressly approved by L-3 Communications
Global Security & Engineering Solutions may void the user’s authority to operate this
equipment.
FCC ID: XG8-TB100001
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation.
When operated above ground, the Fixed Tracking Beacon must be installed with the following
antenna connected to the 900 MHz RF output (ANTENNA PORT 1):
Modified Pulse MSU900FME 900MHz Antenna Assembly
Modifications to the MSU900FME antenna must be per IWT instruction (IWT document no:
ASY-FAA9100-010, Rev. R2A). Modifications include replacing the OTS coaxial cable and
FME connector with a MSHA approved flame resistant RG-58A/U cable with RP-TNC
connector.
IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the
antenna used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Page 4 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
The Fixed Tracking Beacon must be installed 20 cm or more from any personnel in order to
comply with FCC exposure requirements.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These designed limits provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Page 5 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
3. SPECIFICATIONS FOR FAP5010-001
ENVIRONMENTAL
Operating Temperature -30C to +60C ambient
1
Storage Temperature -20C to +35C ambient
Dimensions 4” x 3” x 1.6”
Weight 1 lb
Enclosure IP65
POWER
Battery
Type Alkaline C cells (x2)
ELECTRICAL
Frequency Range 902 – 928 MHz
RF Transmit Power – below ground +10 dBm
RF Transmit Power – above ground +10 dBm
RF output 50 ohms nominal (RP-TNC connector)
Note 1: Operating at extreme temperatures may influence the battery life of the Fixed Tracking
Beacon. To maximize battery life, maintain operating temperatures in the range +15C to +35C.
Page 6 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
4. DESCRIPTION
4.1 Outputs
The following is an explanation of the Fixed Tracking Beacon outputs shown in Figure 1:
LED1: The blue power LED indicates the status of the Fixed Tracking Beacon
(see section 7.0)
ANTENNA PORT 1: 900 MHz antenna port. Connector type is RP-TNC.
FIGURE 1: FIXED TRACKING BEACON CONNECTIONS
4.2 Components Necessary for Installation
The Fixed Tracking Beacon installation uses the following components and accessories (see
sections 5.0 and 6.0 for installation instructions):
Antenna (900 MHz):
The Fixed Tracking Beacon can only use the following antenna model in applications that must
meet FCC requirements:
LED1 ANTENNA
PORT 1
Page 7 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
Modified Pulse MSU900FME 900MHz Antenna Assembly
Modifications to the MSU900FME antenna must be per IWT instruction (IWT document no:
ASY-FAA9100-010, Rev. R2A). Modifications include replacing the OTS coaxial cable and
FME connector with a MSHA approved flame resistant RG-58A/U cable with RP-TNC
connector.
The antenna base includes a magnetic mount for quick installation.
C Cell Alkaline Batteries:
Two C cell alkaline primary batteries power the Fixed Tracking Beacon. The batteries are
located in the battery holder inside the enclosure. Battery maintenance and replacement details
are in section 7.
Magnetic Mounting Feet:
The Fixed Tracking Beacon includes three magnetic mounting feet for quick installation. The
mounting feet screw into the base of the enclosure.
5. PRIOR TO INSTALLATION
5.1 Site Survey
Conduct a survey to determine the appropriate sites to install the Fixed Tracking Beacon from an
RF perspective.
5.2 Visually inspect each Fixed Tracking Beacon to ensure
that:
• The enclosure is free from damage or defects.
• Four screws properly secure the enclosure lid.
Page 8 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
6. INSTALLATION INSTRUCTIONS
6.1 Installations Below Ground
IMPORTANT NOTE:
TRAINED PERSONNEL MUST PROFESSIONALLY INSTALL THE FIXED
TRACKING BEACON.
At each of the sites determined by the survey described in 5.1:
6.1.1 Antenna Placement
Determine the placement for the 900 MHz antenna to ensure proper RF propagation. For units
installed in coal mines below ground, mount the antennas to roof bolts using the magnetic
antenna mount. Select locations that ensure proper RF communication. Antenna location should
not present a safety hazard or opportunity for damaged to occur.
6.1.2 Applying Power to the Fixed Tracking Beacon
Remove the enclosure lid of the Fixed Tracking Beacon. Insert two C cell batteries into the
battery holder. The LED should begin to blink, indicating that the Fixed Tracking Beacon is
transmitting. Replace the enclosure lid ensuring that the LED lines up with the LED lens located
on the lid. Secure the lid with all four screws.
LED
Page 9 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
FIGURE 2: POWERING THE FIXED TRACKING BEACON
(SHOWN WITHOUT BATTERIES)
6.1.3 Fixed Tracking Beacon Enclosure Placement
Locate a place to mount the Fixed Tacking Beacon enclosure. Use the enclosure’s magnetic
mounting feet to mount the Beacon to a roof bolt (or other acceptable location).
6.1.4 Fixed Tracking Beacon Antenna Connection
Connect the antenna cable to ANTENNA PORT 1 of the Fixed Tracking Beacon.
6.2 Installations Above Ground
At each of the sites determined by the survey described in 5.1:
6.2.1 Fixed Tracking Beacon Installation Instructions
Follow installation instructions of 6.1. Equipment above ground should be located so as not to
present a safety hazard or cause damage. Secure all equipment using the proper hardware.
6.2.2 Follow all FCC guidelines listed in Section 2.0.
7. OPERATING AND MAINTENANCE
INSTRUCTIONS
The Fixed Tracking Beacon does not have any direct user interface.
Monitor the status of the Fixed Tracking Beacon by observing the LED mounted on the outside
of the enclosure (LED1):
BLINK (ON—1 ms, OFF—500 ms): Power ON / Device transmitting
OFF: Power OFF / Device not transmitting
Page 10 of 10
Issuer: IWT, Inc. Doc. Num.: 6640-08-0056 Rev: C
Revised: October 26, 2009
Approval: Timothy Dahl
The Fixed Tracking Beacon requires little routine maintenance. Inspect each box periodically
every 3-6 months to ensure that the box remains free of defects. It is important that the box
remains dust tight. Replace defective boxes immediately. Do not continue to use any boxes that
may have had their dust seal compromised.
Replace the C cell batteries inside the Fixed Tracking Beacon enclosure once each year. To
replace the batteries:
1. Remove enclosure lid by unscrewing the four lid screws.
2. Remove the two C cell batteries from the battery holder.
3. Insert two fresh C cell batteries into the battery holder noting proper polarity.
4. Ensure that LED is blinking after replacing batteries.
5. Line up the LED with the LED lens located in the lid of the enclosure.
6. Replace enclosure lid and secure all four lid screws.
To prevent dust and moisture from entering the Fixed Tracking Beacon enclosure during battery
replacement, replace the batteries in a location above ground and free from excessive moisture
and coal dust.