Inovonics Wireless 3B6RTA Remote Pendant Transmitter User Manual f223 v1

Inovonics Wireless Corporation Remote Pendant Transmitter f223 v1

FA223 Install manual

© 1999 Inovonics support@inovonics.com phone: 800.782.2709 www.inovonics.com f223_v1.fm rev 1.00 8/20/99Intended use: The FA223S portable transmitter utilizes Inovon-ics 900MHz Frequency Agile® technology. The transmitter, intended to be installed and serviced by licensed security profes-sionals, transmits messages to an Inovonics receiver. The FA223S has a water-resistant housing suitable for use in showers and bathtubs. It is not, however, designed for prolonged submersion, or for subermersion deeper than one foot. •To activate the FA223S, press and hold the Transmit Button for at least 1 second. (Actual minimum activation interval is .700 second.) •Alarm signals are transmitted multiple times, and are indicated by the blinking transmit LED. •Holding the button results in continuous transmission.•When the button is released, the FA223S will complete its alarm trans-mission, then will send an alarm restoral signal.Dimensions: 2.22" x 1.925" x0.725"Weight: 1.4 oz.External contacts:N/OTypical battery life: 1 to 2 yearsBattery (BAT609): 3.0V lithium Sanyo CR2450—or— Renata CR2450N (The battery is always supervised.)1. Open the transmitter housing by removing three phillips-head screws.2. When prompted by the programming device to plug in the transmitter, connect the programming cable to the 3-pin programming header.3. Press the internal reset button.4. Disconnect the programming cable.5. Re-assemble and thoroughly test the transmitter.NOTE: FA223S transmitters retain programming data in non-volatile mem-ory. They do not require reprogramming after loss of power. Install new bat-tery and press either the internal or the external reset button to re-initialize the transmitter and restore programming. IMPORTANT: The FA223S should always be programmed for supervision.II Inovonics recommends that pendants always be supervised. Pendants should also be tested at least once per week.Suggested check-in interval: 5 minutesExternal contacts: N/OII For information on supervision programming options, request TechNotes TN1025 and TN1032.The FA223S can be carried in 3 convienient ways: • Around the neck as a pendant (standard).• On a belt with the beltclip attachment (standard). • On the arm with optional wristband accessory (ACC634W).II Caution: Neck Cord SafetyWARNING: The neck cord provided with the FA223S is designed for user safety.Substitution of stronger cords or chains may result in injury to the wearer.ExternalTransmit LEDTransmitButtonReset ButtonFA223S Single-button Pendant transmitterOperationSpecifications Changing the battery: 1)Remove 3 screws from the back of the housing. 2)Make sure that the battery is inserted with the positive (+) ter-minal facing the indicated side of the holder. 3)After replacing the battery, press the internal reset button to reset the transmitter to its most recent programming. 4)Replace back cover and care-fully re-tighten screws evenly for tight seal5) Thoroughly test the unit before returning to service.Internal Reset Button 3-pin programming headerBattery Positive IndicatorChanging the batteryProgramming Factory Default / Recommended ProgrammingBelt ClipNeck cord ClipWrist Band (optional)(ACC623W)Recommended method of attaching the neck cord to the FA223SWearing the FA223S: Neck cord, Belt Clip or Wrist Band FA223SInstallationInstructions
Warranty & DisclaimerInovonics Corporation ("Inovonics") warrants its products ("Product" or "Products") to conform to its own specifications and to be free of defects in materials and workmanship under normal use for a period of twenty-four (24) months from the date of manufacture. Within the warranty period Inovon-ics Corporation will repair or replace, at its option, all or any part of the warrantied product. Inovonics will not be responsible for dismantling and/or reinstallation charges. To exercise the warranty, the User ("User", "Installer" or "Consumer") must be given a Return Material Authorization ("RMA") Number by Inovonics. Details of shipment will be arranged at that time.This warranty does not apply in cases of improper installation, misuse, failure to follow installation and operating instructions, alteration, abuse, accident or tampering, and repair by anyone other than Inovonics. This warranty is exclusive and expressly in lieu of all other warranties, obligations or liabilities, whether written, oral, express, or implied, including any warranty of merchantability or fitness for a particular purpose. Inovonics will not be liable to anyone for any consequential or incidental damages for breach of this warranty or any other warranties.This warranty will not be modified, varied or extended. Inovonics does not authorize any person to act on its behalf to modify, vary or extend this warranty. This warranty will apply to Inovonics Products only. All other products, accessories or attachments used in conjunction with Inovonics equipment, including batteries, will be covered solely by their own warranty, if any. Inovonics will not be liable for any direct, incidental or consequential damage or loss whatsoever, caused by the malfunction of Product due to products, accessories, or attachments of other manufacturers, including batteries, used in conjunction with Inovonics Products. This warranty does not warrant the replacement of batteries that are used to power Inovonics Prod-ucts.The User recognizes that a properly installed and maintained security system may only reduce the risk of events such as burglary, robbery, personal injury and fire. It does not insure or guarantee that there will be no death, personal damage and/or damage to property as a result. Inovonics does not claim that the Product may not be compromised and/or circumvented, or that the Product will prevent any death, personal and/or bodily injury and/or damage to property resulting from burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warn-ing or protection.Inovonics Corporation shall have no liability for any death, injury or damage, however incurred, based on a claim that Inovonics Products failed to function. However, if Inovonics is held liable, directly or indirectly, for any loss or damage arising under this limited warranty or other-wise, regardless of cause or origin, Inovonics' maximum liability will not in any case exceed the pur-chase price of the Product, which will be fixed as liquidated damages and not as a penalty, and will be the complete and exclusive remedy against Inovonics.Warning: The User should follow all installation, operation and maintenance instructions. The User is strongly advised to conduct Product and systems tests at least once each week. Changes in environmental conditions, electric or electronic disruptions and tampering, may cause the Product to not perform as expected.Warning: Inovonics warrants its Product to the User. The User is responsible for exercising all due prudence and taking necessary precautions for the safety and protection of lives and property wherever Inovonics Products are installed. Inovonics strongly advises the User to program Products to be supervised whenever used in applications affecting life safety. Users are warned that unsuper-vised devices are subject to undetected failure due to malfunction, battery failure, tampering, or changes in environment.

Navigation menu