Inrico Technologies T196 Smart Phone User Manual T196 FCC
Shenzhen Inrico Electronics Co.,Ltd Smart Phone T196 FCC
T196_FCC_User Manual
![](/img.php?id=3460635&img=bg1.png)
Please read this instruction book carefully before use and keep this with care
T196
FCC ID: 2AIV6-T196
![](/img.php?id=3460635&img=bg2.png)
Warning
● Flammable environment (gas, dust and fog, etc.)
● Please turn off the radio before getting close to the blasting zone or
detonator areas.
General information before use
Please observe the following instructions to prevent fire, injury or damage
to the radio.
◎ The recommended use pattern is 1 min of emission and 4 mins of receives.
Constant emission over long time will cause over heat on the back side. Do
not let the back touch any plastic surface when put it down.
◎ Prohibit to modify this product in any case.
◎ Please do not expose the radio to long-time direct sunlight, neither to close
any heat source.
◎ Please do not expose the radio to dust, damp and spill. and over object that
is unstable.
◎ If abnormal odor or smoke noted from the radio, please shut down
immediately, remove the battery unit, and contact our local authorized service
provider.
![](/img.php?id=3460635&img=bg3.png)
Contents
Unpacking and checking equipment
Accessories
Preparation work
Using the Lithium Battery
Feature of the Lithium battery
Charging for the Lithium battery
Installing accessories
Installing/Removing battery
Installing antenna
Installing belt clip
Installing sling
Installing headset
Knowing the device well
Unit structure
Volume selector/ON and OFF switch
Push To Talk button PTT
Session selector
Indicator lights status
Introduction
Installing SIM card
Basic use
Session selection
FAQ
Indicator light interpretation
Brief technical data
1
1
1
2
2
2
3
3
4
4
5
5
6
7
7
7
7
7
8
8
8
8
9
10
10
![](/img.php?id=3460635&img=bg4.png)
Unpacking and checking equipment
Note: following instructions is only suitable for authorized retailers and
service providers.Carefully unpack the radio. We recommend you
check the items listed in the following table before discarding the
package. If any item is missing, please contact local dealer immediately.
Accessories:
Preparation work
※ Do not overcharge with the battery
Please stop to charging if it is uncompleted in normal time. The battery may
flame, smoke or crack due to abnormal charging process.
※ Do not put battery into the microwave or high pressure container
The battery my flame, smoke or crack.
※ Do not expose broken battery to any flame.
If the battery is seen broken (or with abnormal odor), please remove it from
flammable condition immediately. The fluid in battery is really flammable, which
may cause flame or smoke.
※ Do not use abnormal battery
If the battery is abnormal in odor, color, shape or any other form, please remove
it from charger or radio and do not use it anymore.
※ Please use exclusive adapter
The adapter in accessories is designed exclusively for the bought radio. It ensures
the safety and reliability of battery charging.
Warning
Items
Radio
Lithium battery
AC adapter
Antenna
Sling
belt clip
Instruction manual
Number
1
1
1
1
1
1
1
01
![](/img.php?id=3460635&img=bg5.png)
Using the Lithium Battery
Charge before use
To reduce electrical emission in battery, please remove the battery
from device if not in use withina long time. Please keep the battery
in cool and dry places. When keeping battery for long time:
1、Remove battery from device;
2、If possible, please fully charge for the battery before store;
3、Store the battery in places that are cool and dry (with the
temperature lower than 25 Celsius);
Feature of the Lithium Battery:
※ After repeated charging process, the capacity will decrease.
※ The battery degenerates gradually even without being used.
※ More time will be required when Lithium battery is being charged
in cool condition.
※ Charging and storage of Lithium Battery in relatively warm
condition will jeopardize its service life. Please do not keep them
inside the vehicle or near heating equipment.
※ If the duration of battery shortens significantly, please replace
the battery immediately to prevent fluid leak.
Charging Lithium battery
After the AC adapter is connected and the battery is well placed,
the indicator will show red which means the charging is in progress.
Green will indicate that the battery is fully charged. The indicator
will goes off if the temperature is not proper, the battery is
damaged or the connection is poor.
02
![](/img.php?id=3460635&img=bg6.png)
Installing accessories
Aim the four dents of battery to the corresponding guides
on the back of radio;Push the battery along the guides until
the latch on the back of radio clicks.
When removing the battery, pull down the latch, then push
the battery backwards along the guides.
Battery latch
Battery latch
Installing/Removing battery
※ Do not short out the battery terminal, or set the battery in fire.
※ Do not attempt to remove the shell of battery.
※ Do not install battery in any dangerous condition, since the
possible flame may cause explosion.
03
![](/img.php?id=3460635&img=bg7.png)
Antenna Antenna
Installing antenna
Hold the antenna pedestal, revolve the antenna in clockwise
until it is tightened.
Installing belt clip
If needed, screw the belt clip onto the back of radio by two
screw holes located on the back of radio to facilitate portability.
04
Belt clip
![](/img.php?id=3460635&img=bg8.png)
Installing headset
Open the cover from the top of device to show the headset sockets.
Headset will work immediately after being plugged in.
Installing sling
Take the tail of sling across the oval hole on the back of radio to
install.
05
![](/img.php?id=3460635&img=bg9.png)
Knowing the device well
06
Anten na
Group Selector Knob
Switch / Vol Knob
Indicator
Microphone
Lanyard Hole
Charging Contact
Belt Clip
Battery
Earphone
Jack
Microphone
Interface
PTT
Recording Playback
Single Call
User-defined
![](/img.php?id=3460635&img=bga.png)
Unit structure
1.Volume selector/ ON/OFF switch
A:Clockwise for switch ON, counterclockwise for switch OFF.
B:Clockwise for volume UP, counterclockwise for volume DOWN.
2.Push To Talk button PTT
A:Press PTT button to initiate a call (red light goes on) when
radio is standing by.
B:If not in reception, hold PPT to apply for turn to talk (red light
goes on).
Release the PPT button to quit talk and go back to standing by.
3.Session selector
Revolve the selector for last/next session. And confirm to enter
the current session with voice prompt.
4. Recorder Playback/GPS enable/disable
Press to voice-play the last call(support 10 recorders). Hold for 3
seconds to enable/disable GPS with voice prompt.
5.Indicator light status
The green light goes on after the device is switched on. The green
light flashes fast to indicate network searching. In standing by, the
green light flashes for every 5 seconds. The green light remains on
for reception, and the red light remains on for emission.
07
![](/img.php?id=3460635&img=bgb.png)
1.Installing battery and SIM card
Please insert effective USIM card before use, make sure the
USIM card can be effective in any selected WCDMA cellphone.
(1)Revolve the volume button to switch ON/OFF device.
(2)Remove the battery cover by pushing backwards.
(3)Lift USIM socket cover, place the USIM card in the socket
well in right direction.
(4)Replace the battery and cover.
2.Basic use:
Switch ON: Revolve the volume button clockwise to switch ON
device, there will be voice prompt for switch ON. After the device
is successfully switched ON, the green light goes on first then
flash to indicate network searching. After the network is
connected, there will be voice prompt.
Switch OFF: Revolve the volume button counterclockwise to
switch OFF device, the light will goes off.
Note: Do not frequently switch between ON and OFF, it may
affect the switch function.
Volume adjustment: Revolve clockwise to volume UP,
counterclockwise to volume DOWN.
Headset: Plug in headset, press the PPT button on headset if
there is one to initiate a call, release the button to cancel the call.
Low battery notification: When the battery is lower than 10%,
there will be voice prompt to indicate charging need.
3.Session selection:
Before switching ON, user needs to revolve the selector to
Channel 1 (The default session is Channel one, revolve to select
other sessions. If the session is not available, there will be voice
prompt:No Channel).
Introduction
08
![](/img.php?id=3460635&img=bgc.png)
09
If your radio shows following problem in use, please check the
instruction below, and if the issue still persists, please contact
local authorized service.
1.Poor reception: Possible reasons: signal over your current location
is weak (such as basement or next to a blocking building), or the
network is busy (such as during rush hours).
Solutions: 1. Please move somewhere with improved signal. 2:
Please avoid use in such hours or wait for a while before another
attempt.
2.Echo or noise: Possible reason: the quality of network service
provider is flawed. Solution: Restart the radio will let it automatically
search for available network with better quality.
3.Less duration: Possible reasons: the duration depends a lot on
the settings by network service provider. Use and charging under
condition with high temperature will also jeopardize the battery
duration. Searching for network constantly in weak-network area
will also lower the duration. Solution: if you are at place with weak
signal, please temporarily switch OFF the radio.
4.Unable to connect to network: Possible reasons: USIM card
not effective, poor signal, out of network service area.
Solutions: replace another USIM card, move to somewhere open
and flat, if you are in the building , move near the window.
FAQ
![](/img.php?id=3460635&img=bgd.png)
10
Device Status Indicator Status Frequency
ON/Setting Green on
Searching for network Green flashes fast Flash every 1 sec
Standing by Green flashes slow Flash every 5 secs
Initiating call Red on
Receiving call Green on
Voltage 3.7V
Frequency band GSM850/1900, WCDMA850/1900
Size 59*37*117mm(width*length*height)
Weight ~240g
Working temperature
-10---+55celcius
Storage temperature
-40---+85celcius
Transmit power 23dBm ~ 33dBm@-104dBm
Receive sensitivity
WCDMA: ≤-106.7dBm
GSM : ≤-102dBm
Sound output power 2W@10%distortion
Brief
technical data
Indicator light interpretation
![](/img.php?id=3460635&img=bge.png)
11
Product D
escription
This device does not support the GSM dial and
call function. It only supports GPRS/EDGE/
WCDMA network function. It has no display. It
could not be installed Skype or other network
software. The device does not have any instant
verbal talking and does not have any verbal
dialing function thru connection of network.
There is not any voice communication or FM
transmitter on the device.
T196 is a Push-to-Talk radio. Front-of-face
position for Head SAR testing is necessary.
According to KDB 643646 A2, all sides of the
radio that may be positioned facing the user when
using a body-worn accessory must be considered
for SAR compliance.
When user operates the product using a body-
worn accessory, users only operates the rear
sides of the product to the user. The product is
fixed to the waist, through a microphone and a
headset to communication. Thus, we only tested
the rear side of body-worn positions for Body SAR
testing. The other five sides of body-worn
positions (top, bottom, left, right and front) were
not tested. Therefore, the product complies with
SAR requirement.
The antenna information:
Antenna Gain: 2.15 dBi
Antenna Type: Detachable Dipole Antenna
![](/img.php?id=3460635&img=bgf.png)
FCC Warning
Statement
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and
can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to
radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment
and receiver.
—Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV
technician for help.
Note: Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user's authority to operate the
equipment.
![](/img.php?id=3460635&img=bg10.png)
This mobile device meets guidelines for exposure
to radio waves. Your mobile device is a radio
transmitter and receiver. It is designed not to
exceed the limits for exposure to radio waves
recommended by international guidelines.
The SAR limit adopted by USA and Canada is 1.6
watts/kilogram (W/kg) averaged over one gram of
tissue. The highest SAR value reported to the
Federal Communications Commission (FCC) for
this device type when it is tested for use at the
body is 1.262 W/kg and head is 0.654 W/kg.
The device complies with the RF specifications
when the device is used at a distance of 10mm
from your body and 25mm from face. Ensure that
the device accessories such as a device case and
a device holster are not composed of metal
components. Keep your device 10mm away from
your body and 25mm away from your face to
meet the requirement earlier mentioned.