user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2964578 |
| Application ID | z3WVZ93F0O88oaxg5vWp5A== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 7.07kB (88415 bits) |
| Date Submitted | 2016-04-20 00:00:00 |
| Date Available | 2016-04-20 00:00:00 |
| Creation Date | 2016-04-04 13:28:25 |
| Producing Software | Acrobat Distiller 15.0 (Windows) |
| Document Lastmod | 2016-04-04 13:28:25 |
| Document Title | Microsoft Word - Regulatory and Safety_Flyer_v1.1.doc |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | mbriggs |
IMPORTANT SAFETY & REGULATORY INFORMATION DO NOT DISCARD – DOCUMENT MUST REMAIN WITH PRODUCT Model: A2RX (Sea Dunes) PRU Module – Regulatory Information This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications made to this device, unless expressly approved by the manufacturer, may void the user’s rights to operate this equipment. Note: This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. Radio Frequency Exposure and Compatibility with Implantable Cardiac Medical Devices. Wireless Power devices are designed to meet all applicable RF health and safety regulations prescribed by individual countries around the world. Through complex testing procedures we have demonstrated to appropriate country regulators that the RF emissions from our wireless power devices meet the basic exposure restrictions set forth in ICNIRP or IEEE or similar international RF safety standards. Based on readily available information, Intel’s wireless power device should not cause interference with any implantable cardiac device. However because each cardiac device can be different and some may be affected by low powered RF fields, individuals wearing implantable cardiac devices should not be in very close proximity ( or direct contact) with the wireless power device. Individuals should discuss any concerns about the compatibility of their medical device with their physician or medical device manufacturer. Page 1 of 2 Monday, April 04, 2016 IMPORTANT SAFETY & REGULATORY INFORMATION DO NOT DISCARD – DOCUMENT MUST REMAIN WITH PRODUCT This PRU module shall be integrated into host systems in accordance with the Intel Integration Guide. This device has been approved as a module by the FCC. To leverage this approval the module must be installed as described in the Integration Guide and with consideration to the following: The Bluetooth module has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, or having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device without additional certification under a Class 2 Permissive Change or separate, stand-alone filing. IFA antenna type, 2.6 dBi gain, nominal 50ohm impedance. The approval only covers the Bluetooth functions of the module. The module and host system into which the module is installed needs to comply, as a system, with FCC Part 18 consumer device requirements when in the wireless charging mode. It is recommended that this mode be tested with the PTU (Power Transmit Unit) you are marketing with your system. If you are not manufacturing a PTU then this testing may be performed with any commercially available PTU that supports wireless charging of your device. In addition the host system, with PRU installed, needs to comply with all pertinent regulatory requirements applicable to the host system. For example, when integrated into a laptop the system shall comply with the technical requirements and approval procedures for a Part 15 Subpart B digital device. Compliance of any other transmitters located within the host with the relevant technical requirements should be demonstrated with the PRU installed. For rf exposure compliance note that the Bluetooth transmitter in the PRU module is only active when the system is wirelessly charging and so the exposure condition (portable versus mobile) will depend on relative locations of the other transmitting antennas to people when in the wireless charging mode. Unless the FCC ID (and Industry Canada number) on the PRU module are visible to the end user the host system shall identify the FCC ID of the module on its regulatory label. This label needs to be visible to the end user at the time of purchase (refer also to the FCC KDB 784748 D01, KDB 784748 D02 and KDB 784748 D03) and must include the words: Contains FCC ID: 2AGRJ-A2RX. The regulatory information on page 1 of this document shall be reproduced in the host system manual. For additional information on modular approvals refer to KDB 996369 D01 and KDB 996369 D02. Page 2 of 2 Monday, April 04, 2016
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Author : mbriggs Create Date : 2016:04:04 13:28:25-07:00 Modify Date : 2016:04:04 13:28:25-07:00 XMP Toolkit : Adobe XMP Core 5.6-c015 81.157285, 2014/12/12-00:43:15 Producer : Acrobat Distiller 15.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Format : application/pdf Title : Microsoft Word - Regulatory and Safety_Flyer_v1.1.doc Creator : mbriggs Document ID : uuid:a5fab634-8d56-4b9c-a7d8-a5106fa9d3d7 Instance ID : uuid:8b8bffb9-63e8-469f-a407-bce93eae2931 Page Count : 2EXIF Metadata provided by EXIF.tools