Interactive Technologies IQ6924 LOW POWER TRANSMITTER (2400-2483.5 MHz) User Manual OEM manual IQ6924

Interactive Technologies, Inc. LOW POWER TRANSMITTER (2400-2483.5 MHz) OEM manual IQ6924

User Manual

Download: Interactive Technologies IQ6924 LOW POWER TRANSMITTER (2400-2483.5 MHz) User Manual OEM manual IQ6924
Mirror Download [FCC.gov]Interactive Technologies IQ6924 LOW POWER TRANSMITTER (2400-2483.5 MHz) User Manual OEM manual IQ6924
Document ID1894251
Application IDuj2DWwpJCCX44hxLDhUk6g==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize43.06kB (538266 bits)
Date Submitted2013-02-05 00:00:00
Date Available2013-02-05 00:00:00
Creation Date2013-01-24 09:35:16
Producing SoftwareGPL Ghostscript 8.15
Document Lastmod2013-01-24 09:35:16
Document TitleMicrosoft Word - OEM manual IQ6924.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: workcpu

OEM MANUAL
Refer to Freescale MC13213 operations manuals for
complete descriptions.
Microcontroller Features
• Low voltage MCU with 40 MHz low power HCS08 CPU core
• Up to 60K flash memory with block protection and security and 4K RAM
— MC13211: 16KB Flash, 1KB RAM
— MC13212: 32KB Flash, 2KB RAM
— MC13213: 60KB Flash, 4KB RAM
• Low power modes (Wait plus three Stop modes)
• Dedicated serial peripheral interface (SPI) connected internally to 802.15.4 modem
• One external 4-channel (5-channel internal) 16-bit timer/pulse width modulator (TPM)
module and
one external 1-channel (3-channel internal) 16-bit timer/pulse width modulator module,
each with
selectable input capture, output capture, and PWM capability.
• 8-bit port keyboard interrupt (KBI)
• 8-channel 8-10-bit ADC
• Two independent serial communication interfaces (SCI)
• Multiple clock source options
— Internal clock generator (ICG) with 243 kHz oscillator that has +/-0.2% trimming
resolution
and +/-0.5% deviation across voltage.
— Start-up oscillator of approximately 8 MHz
— External crystal or resonator
— External source from modem clock for very high accuracy source or system low-cost
option
• Inter-integrated circuit (IIC) interface with 100 kbps operation
• In-circuit debug and flash programming available via on-chip background debug
module (BDM)
— Two comparator and 9 trigger modes
— Eight deep FIFO for storing change-of-flow addresses and event-only data
— Tag and force breakpoints
— In-circuit debugging with single breakpoint
• System protection features
— Programmable low voltage interrupt (LVI)
— Optional watchdog timer (COP)
— Illegal opcode detection
• Up to 32 MCU GPIO with programmable pull-ups
RF Modem Features
• Fully compliant 802.15.4 Standard transceiver supports 250 kbps O-QPSK data in 5.0
MHz channels and full spread-spectrum encode and decode
• Operates on one of 16 selectable channels in the 2.4 GHz ISM band
• -1 to 0 dBm nominal output power, programmable from -27 dBm to +3 dBm typical
• Receive sensitivity of <-92 dBm (typical) at 1% PER, 20-byte packet, much better than
the 802.15.4 Standard of -85 dBm
• Integrated transmit/receive switch
VOLTAGE INFORMATION:
MODULE PINOUTS:
Connector is 2 each 2x20 pins, 1mm x 1mm pitch
MC13213 PORT BOARD CONNECTIONS:
P1:
1 – D5
2 – D6
3 – D4
4 – D7
5 – GND
6 – B0
7 – GND
8 – B1
9 – VCC
10 – B2
11 – VCC
12 – B3
13 – VCC
14 – B4
15 – VCC
16 – B5
17 – GND
18 – B6
19 – GND
20 – B7
P2:
1 – A0
2 – A1
3 – E1 (RXD1)
4 – A2
5 – D0 (TXD1)
6 – A3
7 – C7
8 – A4
9 – C6
10 – A5
11 – C5
12 – A6
13 – C4
14 – A7
15 – C3 (SCL)
16 – BKGD
17 – C2 (SDA)
18 – RESET
19 –.C1 (RXD2)
20 – C0 (TXD2)
BOARD LAYOUT:
BOTTOM VIEW (TO BE MOUNTED FACE DOWN ON HEADER PINS):
CHANNEL NUMBER TO FREQUENCY RANGE:
* Channel number (0-15)
* Channel frequencies :
* 0 : 2.405GHz
* 1 : 2.410GHz
* 2 : 2.415GHz
* 3 : 2.420GHz
* 4 : 2.425GHz
* 5 : 2.430GHz
* 6 : 2.435GHz
* 7 : 2.440GHz
* 8 : 2.445GHz
* 9 : 2.450GHz
* 10: 2.455GHz
* 11: 2.460GHz
* 12: 2.465GHz
* 13: 2.470GHz
* 14: 2.475GHz
* 15: 2.480GHz
§ 15.19 Labeling requirements
(a) In addition to the requirements in part 2 of this chapter, a device
subject to certification, or verification shall be labeled as follows:
(3) All other devices shall bear the following statement in a conspicuous
location on the device:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
§ 15.21 Information to user
The users manual or instruction manual for an intentional or unintentional
radiator shall caution the user that changes or modifications not expressly
approved by the party responsible for compliance could void the user's
authority to operate the equipment. In cases where the manual is provided
only in a form other than paper, such as on a computer disk or over the
Internet, the information required by this section may be included in the
manual in that alternative form, provided the user can reasonably be
expected to have the capability to access information in that form.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 5
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2013:01:24 09:35:16
Modify Date                     : 2013:01:24 09:35:16
Title                           : Microsoft Word - OEM manual IQ6924.doc
Creator                         : PScript5.dll Version 5.2.2
Author                          : workcpu
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ULP-IQ6924

Navigation menu