Intermatic H0020 Wall Switch with Transmitter User Manual HA20 ENGLISH indd

Intermatic Inc Wall Switch with Transmitter HA20 ENGLISH indd

Users Manual

Download: Intermatic H0020 Wall Switch with Transmitter User Manual HA20 ENGLISH indd
Mirror Download [FCC.gov]Intermatic H0020 Wall Switch with Transmitter User Manual HA20 ENGLISH indd
Document ID847867
Application IDqdIrSuG0HDULVS5lCm8knA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize63.84kB (797991 bits)
Date Submitted2007-09-26 00:00:00
Date Available2007-09-26 00:00:00
Creation Date2007-07-05 06:47:57
Producing SoftwareAdobe PDF Library 8.0
Document Lastmod2007-08-30 16:05:58
Document TitleHA20-ENGLISH.indd
Document CreatorAdobe InDesign CS3 (5.0)

MODEL HA20
600 Watt In-Wall
Toggle-Style Dimmer
Federal Communications Commission Statement / Industry Canada Statement
This device complies with part 15 of the FCC rules. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna or device.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTICE — Changes or modifications not expressly approved by Intermatic Inc., could void the user’s authority to operate the equipment.
The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met.
Installation and Programming Instructions
1 – Wire and Install the HA20 In-Wall Dimmer
Limited Six-Year Warranty
If within six (6) years from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original household purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or
any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost
of the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit
damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED
WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the
authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000 http://www.homesettings.com
Please be sure to wrap the product securely to avoid shipping damage.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
158HA13317
WARNING
• Electrical shock hazard. Risk of injury or death. Remove electrical
power at service panel before installing.
• Follow local electrical codes during installation.
• For indoor use only.
Before installing, make sure that you…
• Understand basic wiring principles and techniques (IF NOT, USE A
QUALIFIED ELECTRICIAN FOR THIS INSTALLATION.)
• Can interpret wiring diagrams
• Have circuit-wiring experience
• Read all instructions and documentation and save for future reference
• Are prepared to test your work, making sure you have wired the receptacle according to your local electrical code
Thank you for purchasing an Intermatic HomeSettings device
With HomeSettings devices, you can reliably and remotely
control your household lighting. The outstanding features of the
HomeSettings HA20 600W In-Wall Dimmer include:
• Feedback that will allow you to see whether your device has
received the ON/OFF/DIM signal.
• Wireless signal reliability — each HomeSettings product
has a special feature that virtually guarantees that wireless
signals are received.
• Manual override.
• Can be used with toggle-style wall plates (not included)
• Compatible with multiple location ON/OFF control using
conventional 3-way or 4-way wiring devices.
Because the HA20 In-Wall Dimmer is a Z-Wave™ device, it is
compatible with any HomeSettings network, other Z-Wave networks, and all HomeSettings or other Z-Wave devices displaying the Z-Wave logo, regardless of manufacturer.
Each module in a Z-Wave network
communicates with every other
module, routing your commands to
their destination by the most reliable
pathway. When Z-Wave devices are
installed throughout the house, signals
are automatically routed around obstacles or dead spots, for dependable
performance.
• To manually turn ON the light switch, flip the toggle up and release.
• To manually turn OFF the light switch, flip he toggle down and release.
• To manually DIM the light, press and hold the toggle up or down.
The most basic installation procedure is to use the HA20 in a
Single Pole application—a circuit where a single switch controls a light, as shown in the wiring diagram below.
Single Pole Application
HOT
120VAC
50/60 Hz
NEUTRAL
BLACK
GREEN
BLUE
LOAD
RED
Incandescent
Lighting Load
HA20
Other installation diagrams are shown on the next page.
1. Turn off power at the service panel by REMOVING THE
CORRECT FUSE or TURNING THE CIRCUIT BREAKER OFF.
2. Remove existing wall switch from the box if necessary.
3. Trim building wires to 7/16”.
4. Connect the BLACK wire of the HA20 to the hot
building wire (the wire leading to the circuit breaker
or fuse box), using a twist connector (provided).
NOTE: Twist connectors provided are suitable for
copper wire only. For aluminum wire, consult an
electrician.
NOTE: Insert wires straight into twist connector,
then twist clockwise. Make sure all twist connectors are tight. Secure each twist connector with
electrical tape. Make sure no bare wire shows
below the wire connector.
5. Connect the BLUE wire of the HA20 to the load wire, using
a twist connector (provided).
6. Connect the ground wire from the box to the GREEN wire
on the HA20 In-Wall Dimmer. If there is no ground wire,
ground the HA20 unit to the box. If the box is plastic, connect the GREEN wire to ground as supplied or contact an
electrician.
7. Remove the semi-stripped end of the Red wire of the HA20
and apply the twist connector to this wire. The RED wire is
not used in the single-pole application.
8. Tuck wires into wall box leaving room for the HA20 unit.
9. Using screws provided, mount the HA20 unit to the wall
box, then install the toggle-style wall plate (not provided).
10. Turn power back on at the service panel.
NOTE: Before operating the switch, check to
make sure the small switch below the toggle is
in the ON or left position.
NOTE: When changing a light bulb, slide the
switch to the OFF or right position. This prevents chance of electric shock during the bulb
change. When finished, slide the switch back
to the ON or left position. See figure (right) for
location of the sliding switch.
2 – INCLUDE the In-Wall Dimmer in your Network
After hard-wiring the HA20 into place, the device is ready to join
your HomeSettings network—or any network that supports ZWave™ devices—through a process called INCLUSION.
1. Put the controller into INCLUSION mode. On the HA07
Master Controller or the HA09 Handy Controller, press and
release the INCLUDE button. For other
manufacturers’ controllers, follow the
instructions provided by the manufacturer.
2. Flip the TOGGLE switch of the HA20
In-Wall Dimmer. If the inclusion is
successful:
- The HA07 screen will display SUCCESSFUL.
- The HA09 will show a solid GREEN light for 2 seconds.
If the screen displays NOT SUCCESSFUL or the light is RED,
the inclusion has failed. Try again. If the procedure continues
to fail, contact Intermatic Customer Service.
Optional: EXCLUDE the In-Wall Dimmer from your Network
If necessary, you can delete the HA20 In-Wall Dimmer from
your HomeSettings network—or any network that supports
Z-Wave devices—through a process called EXCLUSION.
1. Put the controller into EXCLUSION mode. On the HA07
Master Controller or the HA09 Handy Controller, press and
release the DELETE button. For other manufacturers’ controllers, follow the instructions provided by the manufacturer.
2. Flip the TOGGLE switch of the HA20 In-Wall Dimmer. If the
exclusion is successful:
- The HA07 screen will display SUCCESSFUL.
- The HA09 will show a solid GREEN light for 2 seconds.
If the screen displays NOT SUCCESSFUL or the light is RED,
the deletion has failed. Try again. If the procedure continues
to fail, contact Intermatic Customer Service.
Technical Information
•
3 – ASSOCIATE the In-Wall Dimmer with a Control Channel
•
After including your HA20 In-Wall Dimmer with your HomeSettings network, you must associate it with a specific control
channel (or button) so you can operate it by remote control.
For a non-HomeSettings network, follow controller instructions
provided by the manufacturer.
1. Decide which pair of ON/OFF buttons you want to use to control the In-Wall Dimmer. Each pair represents a channel.
2. Press and hold (at the same time) both ON and OFF buttons
on the HA07 Master Controller or the HA09 Handy Controller.
After about 3 seconds:
- The Master Controller screen will display LEARN.
- The Handy Controller lights will rapidly flash GREEN and
RED at the same time.
3. Release the ON and OFF buttons on the controller.
4. Press and hold the INCLUDE button on the Master Controller
or the Handy Controller.
- The Master Controller screen will display INCL.
- The Handy Controller will show a solid GREEN light only.
5. While still holding the INCLUDE button, adjust the TOGGLE
switch on the In-Wall Dimmer to adjust the light to the desired level.
6. Release the INCLUDE button. If the association is successful:
- The Master Controller screen will display SUCCESSFUL.
- The Handy Controller GREEN light will simply turn off.
7. Test the channel you have just programmed by pressing its
ON and OFF buttons. The light should power ON or OFF at the
level you have set.
If the screen displays NOT SUCCESSFUL or the light is RED,
the association has failed. Try again. If the procedure continues to fail, contact Intermatic Customer Service.
•
•
•
•
•
For control of permanently installed incandescent lamp
fixtures only
Ratings: 600 Watts tungsten, 40 Watts minimum
120 VAC, 50/60 Hz
Derating: 500 Watts double gang, 400 Watts triple gang
Operating Temperature Range: 32°F to 104°F / 0°C to 40°C
Radio Operating Frequency: 908.42 MHz @ 9.6 kbps
908.40 MHz @ 40 kbps
RF (wireless) Range: 100 ft. under operating conditions
Made in China
Our products are constantly evolving. To see if advanced functionality is
possible with your product, look it up at www.homesettings.com.
Additional Wiring and Installation Diagrams
2 Switch/3-way Application with
Single-Pole Remote Switch
HOT
120VAC
50/60 Hz
Incandescent
Lighting Load
BLUE
BLACK
GREEN
SINGLE
POLE
SWITCH
RED
HA20
NEUTRAL
2 Switch / 3-way Application with 3-way Remote Switch
18 ga. MIN (not supplied)
HOT
120VAC
50/60 Hz
BLUE
BLACK
GREEN
3-WAY
SWITCH
RED
HA20
3 Switch Application
120VAC
50/60 Hz
ADDITIONAL WIRE
BLACK
BLUE
GREEN
RED
3-WAY
SWITCH
HA20
ADDITIONAL WIRE
GREEN
3-WAY
SWITCH
RED
COMMON
HA20
ADDITIONAL WIRE
Incandescent
Lighting Load
BLUE
BLACK
3-WAY
SWITCH
NEUTRAL
3-WAY
SWITCH
4-WAY
SWITCH
COMMON
Multi-Way Application
120VAC
50/60 Hz
Incandescent
Lighting Load
BLUE
BLACK
NEUTRAL
HOT
3-WAY
SWITCH
COMMON
4 Switch Application
120VAC
50/60 Hz
Incandescent
Lighting Load
COMMON
NEUTRAL
HOT
Incandescent
Lighting Load
COMMON
NEUTRAL
HOT
NOT
USED
GREEN
RED
COMMON
HA20
4-WAY
SWITCH
4-WAY
SWITCH
3-WAY COMMON
SWITCH

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-702
Instance ID                     : uuid:3c52227e-33ad-49f4-92e2-073979557f41
Document ID                     : adobe:docid:indd:6231df0c-9325-11db-a967-92bf83b3029f
Rendition Class                 : proof:pdf
Derived From Instance ID        : 9f256829-755d-11db-ac21-db5dacb40899
Derived From Document ID        : adobe:docid:indd:98cafdea-74b2-11db-8f18-d11dc2954f96
Create Date                     : 2007:07:05 06:47:57-05:00
Modify Date                     : 2007:08:30 16:05:58-05:00
Metadata Date                   : 2007:08:30 16:05:58-05:00
Creator Tool                    : Adobe InDesign CS3 (5.0)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 9138 bytes, use -b option to extract)
Format                          : application/pdf
Title                           : HA20-ENGLISH.indd
Producer                        : Adobe PDF Library 8.0
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Page Count                      : 2
Creator                         : Adobe InDesign CS3 (5.0)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: DGZH0020

Navigation menu