Intermatic Et8000 Series Instructions Owner S Manual

39630-Installationsheet 39630-InstallationSheet 39630-InstallationSheet 078275 Batch5 unilog cesco-content

2014-07-06

: Intermatic Intermatic-Et8000-Series-Instructions-Owner-S-Manual intermatic-et8000-series-instructions-owner-s-manual intermatic pdf

Open the PDF directly: View PDF PDF.
Page Count: 4

Electronic Astronomic
7-Day Time Switch
Time Switch
• InputVoltage:120/208/240/277VAC,50/60Hz
• PowerConsumption:6.0wattsmax.
• ContactConguration:SPST(ET8015C),DPST(ET8215C),and
SPDT(ET8115C).Seewiringdiagramsonnextpage.
Switch Ratings—ET8015C, ET8215C (per pole)
• 30AInductive/Resistive:24/120/208/240VAC,60Hz
• 20ABallast:120-277VAC,60Hz
• 20AResistive:28VDC
• 5ATungsten:120/240VAC,60Hz
• 1HP:120VAC,60Hz
• 2HP:240VAC,60Hz
Switch Ratings—ET8115C (NO/NC) Normally Open/Normally Closed Contact
• 20A/10AInductive/Resistive:120/208/240VAC,60Hz
• 20A/3ABallast:120-277VAC,60Hz
• 5A:120/240VACTungsten
• 1HP/¼HP:120VAC,60Hz
• 2HP/½HP:240VAC,60Hz
Set Points (Events)—EachloadoutputoftheTimeSwitchcansupportup
to14timedONand14timedOFFeventsperdayaswellasAstroON
andAstroOFFevents.
Battery-Powered Clock Operation—2yearsminimum(uses2AAA
industrialgradealkalinebatteries,supplied)
Minimum ON or OFF time—1minute
Maximum ON or OFF time—6days,23hours,59minutes
Shipping Weight—2.5lb.(1.1kg)
Enclosures—Threeenclosureoptionsareavailable.
• ET8xx5C–NEMA1indoormetalenclosure
• ET8xx5CR–NEMA3Rindoor/outdoorlockablemetalenclosure
• ET8xx5CPD82–NEMA3Rindoor/outdoorlockableimpactresis-
tantpolycarbonateenclosurewithclearcover
Knockouts—Combination1/2-3/4inchsize,1onbackandeachside,
2onbottom
Wire Size—AWG#10through#18
Installation and User Instructions
MODEL ET8000 Series
TheIntermaticET8000SeriesElectronicAstronomic7-DayTime
Switchautomaticallyswitchesloadstoapresetweeklyschedulewith
to-the-minuteaccuracy.
• Theastronomicfeatureprovidesanautomaticallyadjustedsunset
ONandsunriseOFFtoeliminatetheneedforseparatephoto
controldevices.
• Theindependent7-dayprogrammingprovidescompleteexibility
forapplicationswhereloadswitchingdifferseachdayoftheweek.
• Astronomicprogrammingcanbecombinedwithindependent
programmingtoprovideasunsetONandtimedOFFprogram.
UsetheET8000seriesasanON/OFFtimerinapplicationsrequiring
7-dayastronomicloadcontrolsuchaslighting,airconditioningsystems,
pumps,etc.EachloadoutputoftheTimeSwitchcansupportupto14
timedONand14timedOFFeventsperdayaswellasAstroONand
AstroOFFevents.TheprogramcanbeoverriddenbypushingtheON/
OFFloadoverridebutton(s).
TheET8000SeriesTimeSwitchisdesignedtodirectlyswitchtung-
stenorballastloadsuptoitsrating,andinductiveorresistiveloads
upto30Aat120,208,240,or277VAC.
Specifications
With Battery
Carryover
Description
WARNING: Disconnect the
power to the Time Switch
and the loads before instal-
lation.
1. Removethemecha-
nismfromthecaseby
depressingthecatchat
thetopofthecaseand
pullingout,asshown.
CAUTION: Do not
touch circuit board
components since
static discharge could damage the microprocessor.
2. Setvoltageselectorfordesiredinputvoltage.
Thetimerisshippedwithvoltagesetfor120
VAC.Tooperateat208,240or277VAC,move
theselectorswitchtothedesiredsettingas
markedonthecircuitboard.SeelocationAin
Rear Viewaboveanddetailattheright.
3. ThetimerisshippedwithDST(DaylightSaving
Time)enabled.TodisableDST,insertajumperatlocation
markedDST.SeelocationBinRear Viewabove
anddetailattheright.
4. ET8215C ONLY—Decidewhetheryouwantto
controlmultipleloadssimultaneously(SIM),
independently(IND),orwitha2-secondpulse
(PUL)(e.g.,forusewithmechanicallyheld
contactorsorbellringingapplications),andmakesurethe
jumperispositionedaccordingly.SeelocationBinRear View
aboveanddetailattheright.(Theunitisshippedwiththeloads
setforIND.)
Installation Instructions
Slide down
to remove
battery case
Snap out catch
Tilt top forward
Front View Rear View
B
A
• Electrical shock hazard. To avoid fire, shock, or death, disconnect all
power before installing or servicing time switch or connected loads.
• Follow local electrical and safety codes, National Electric Code (NEC)
and Occupational Safety and Health Act Codes (OSHA).
• If the power disconnect point is out of sight, lock it in the OFF position
and tag it to prevent unexpected application of power.
• This time switch must be grounded.
• Do not exceed maximum current carrying capacity.
• Always replace the plastic insulator covering the terminal before
powering ON.
WARNING–Risk of Fire or Electric Shock
5. Mounttheenclosureinthedesiredlocationusingthe3mount-
ingholesprovided.
Position at eye level if possible, providing space to the left of
the enclosure for the cover to swing open fully, as shown.
6. Replacethemechanismintheenclosure.
7. Lifttheleftsideoftheplasticinsulatorofftheretainingpostand
pivotitupandawaytoexposetheterminalstrip.
8. Stripthesupplyandloadwiresto1/2”.
Use AWG#10-#18 copper conductors only.
Knockouts
Mounting holes
1
Neutral
120VAC
Input
Hot
234
Timer Power
Load
Install jumper
only if timer input
and load voltage
are the same
ET8015 configured for SPST, 120 VAC load
1
Line 2
120/208/240/277
VAC Input
Line 1
23456
Load
1Load
2
Timer Power
Install jumper only if timer input
and load voltage are the same
ET8115 configured for SPDT load switching
1
Line 2
240VAC Input
Line 1
23456
Line 1
Line 2
Install jumper only if timer input
and load voltage are the same
Timer Power
Load
ET8215 configured for 240VAC DPST load
with jumper set to SIM
1
Line 2
120/208/240/277
VAC Input
Line 1
23456
ON
Install jumper only if timer input
and load voltage are the same OFF
Timer Power
ET8215 configured for pulse SPST load
with jumper set to PUL
1
Line 2
120/208/240/277
VAC Input
Line 1
23456
Load
1
Timer Power
Load
2
ET8215 configured for 2 SPST loads
with jumper set to IND
1
Line 2
120/208/240/277
VAC Input
Line 1
23456
Load
1
Timer Power
Load
2
ET8215 configured for DPST loads
with jumper set to SIM
Mounting
Holes
Knockouts
Mounting
Hole
9. Insertthewireendsundertheproperterminalplates(see
wiringdiagramselsewhereonthispage)andtightenthescrews
rmly.
10.Connectgroundwiretogroundingterminalatbottomofenclosure.
11.Replacetheplasticinsulatorontheretainingpost.
12.Removethebatterycasebyslidingitdownasshownbythe
arrows,theninstall2AAAalkalinebatteries.Makesurethe
batteriesarepointinginthedirectionshown.
13.VerifythatthedisplayisONtomakesurethebatteriesareOK.
If the display shows scrambled information, press the RESET
button to clear it up.
14.ApplypowertotheTimeSwitch.
IMPORTANT:
PressandholdtheENTERbutton,thenpresstheRESETbutton.The
screenwillash12:00AMandMON,andtimerstatusisManual
Mode.
NOTE: You must reset the time switch using this procedure
whenever you change the jumpers.
The Time Switch is now ready for programming.
Programming Overview
BypressingtheMODEbutton,theTimeSwitchwillcyclethroughthe
menusnecessaryforprogrammingthecurrenttime,date,astrozone,
astroevents,andtimedevents.
ThebasicprocedureistousetheMODEbuttontomovefromone
menutothenext(e.g.,DATE,TIME,etc.),the+or– buttonsforthe
rstpartofasetting(e.g.,MONTH),theENTERbuttontomoveto
thenextpartofthesetting(e.g.,YEAR),thenMODEtoexitandmove
tothenextmenu.Toskipamenu,pressMODEtomoveahead.
If you make a mistake, press the MODE button repeatedly to cycle
back around to the error, then make the correct entry.
NOTE: DATE and TIME must be set before you can access any
other programming menus.
1 – Setting Date
1. PresstheMODEbuttonrepeatedlyuntilthewordsSETand
DATEappearintheupperareaofthedisplay.
2 – Setting Time
1. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewords
SETandCLOCKappearintheupperareaofthedisplay.
2. Pressthe+or– buttonstoenterthecurrenttime.
NOTE: To go from AM to PM, keep pressing the +or
– buttons to cycle through the day. You can hold the+or
– buttons down for 3 seconds to make the time scroll
quickly.
3. PresstheMODEbuttontoexitandadvancetosettingAstroZone.
2. Pressthe+or–buttonstoenterthecurrentMonth.
3. PresstheENTERbuttonwhentheMonthiscorrecttosavethe
setting.ThescreenadvancestocurrentDate.
4. Againpressthe+or– buttonstoenterthecurrentDate,fol-
lowedbytheENTERbutton.
5. RepeattosetthecorrectYear.
6. PresstheMODEbuttontoexitandadvancetosettingthetime.
Wiring Diagrams
AnASTROeventwillletyousetSunsetONandSunupOFFevents.
1. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewords
SET,ASTRO,andON/OFFEVENTSappearintheupperareaof
thedisplay.
2. PresstheENTERbuttonifnecessarytodisplayON@.
3. MakesureyouknowwhichdaysyouwanttheEventtobe
active.
- IfyouwanttheEventtooccureverydayoftheweek,press
theDAYbuttontodisplaySUNSETandalldays.
- IfyouwanttheEventtooccurforadifferentcombinationof
5a – Setting SUNSET ON/SUNUP OFF Events
3 – Setting Astro Zone
AstroZoneishowfarnorthorsouththelocationis,toadjustfor
differencesinsunriseandsunsetforbetteraccuracyinturninglights
onandoffatdawnanddusk.
1. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewords
SETandASTROZONE
appearintheupper
areaofthedisplay.
2. Pressthe+or– buttons
todisplaytheZonethat
includesthelocation.
Usethemapattheright
asareference.
3. PresstheMODEbuttontoexitandadvancetosettingexact
Astrotimes.
Fig. 8
South
North
Center
North
Center
South
4 – Setting Exact Astro Times
WhenyouchooseanAstroZone,theTimeSwitchusesanapproxi-
matetimeforsunupandsunset,adjustingautomaticallyasthe
seasonschange(earliersunsetinwinter,etc.)Youcansetexact
sunupandsunsettimes,whichareavailableinthenewspaperoron
theInternet.
Formulti-circuittimeswitchET8215C,youcansetmultiplesunup
andsunsettimes—useful,forexample,inenvironmentsinvolving
lightingwithdifferentwarm-uptimes.
1. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewords
SETandSUNUPappearintheupperareaofthedisplay.The
displayalsoshowsthedefaultsunuptimeforthedateandzone.
2. Pressthe+or– buttonstoadjustthesunuptime.You can offset
the time up to 120 minutes in either direction.
3. PresstheMODEbutton:
- Ifamulti-circuittimeswitch,SUNUPandLOAD2appear
onthedisplay.
a. Pressthe+or– buttonstosettheexactSunuptimefor
Load2.
b.PresstheMODEbuttontoadvancetoSunsetforLoad1.
- Ifasingle-circuittimeswitch,
ThewordsSETandSUNSETappearonthedisplay,alongwith
thedefaultsunsettimeforthedateandzone.
4. Pressthe+or– buttonstoadjustthesunsettime.You can
offset the time up to 2 hours (120 minutes) in either direction.
5. PresstheMODEbutton:
- Ifamulti-circuittimeswitch,SUNSETandLOAD2appear
onthedisplay.
a. Pressthe+or– buttonstosettheexactSunsettimefor
Load2.
b.PresstheMODEbutton.
- Ifasingle-circuittimeswitch,
Thetimeswitchexitsandadvancestosettingevents.
days,presstheDAYbuttonagainasnecessarytocycle
throughthedaysorcombinationofdaysyouwant.
NOTE: To remove an individual day, press the DAY button
until the day is blinking, then press the – button.
4. Whenyouhavesettheeventcorrectly,presstheENTERbutton
tosetthenextAstroevent,whichisforSunupOFF.Thewords
SET,ASTRO,ON/OFFEVENTS,andOFF@display.
5. RepeatfromStep3abovetosettheeventforOFFinsteadofON.
6. PresstheMODEbuttontoexitandadvancetosettingxedtime
events.
AnASTROeventwillletyousetSunsetONandSunupOFFevents.
Whenthecircuitsofmulti-circuittimeswitchET8215Csettobe
independentofeachother,youcansetsunupandsunsettimesfor
eitherorbothcircuits.
1. Verifythatthetwocircuitsareindependent.RefertoStep4in
Installation Instructionsonpage1.
2. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewordsSET,
ASTRO,ON/OFFEVENTS,andLOAD1appearinthedisplay.
3. PresstheENTERbuttonifnecessarytodisplayON@.
4. MakesureyouknowwhichdaysyouwanttheSunsetON
eventtobeactive.
- IfyouwanttheEventtooccureverydayoftheweek,press
theDAYbuttontodisplaySUNSETandalldays.
- IfyouwanttheEventtooccurforadifferentcombinationof
days,presstheDAYbuttonagainasnecessarytocycle
throughthedaysorcombinationofdaysyouwant.
NOTE: To remove an individual day, press the DAY button
until the day is blinking, then press the – button.
5. Whenyouhavesettheeventcorrectly,presstheENTERbuttonto
setthenextAstroevent,whichisSunsetONforLoad2.Thewords
SET,ASTRO,ON/OFFEVENTS,LOAD2,andON@appearinthe
display.
6. RepeatfromStep4abovetosettheeventforON.
7. PresstheENTERbuttontosetSunupOFFforLoad1.The
wordsSET,ASTRO,ON/OFFEVENTS,LOAD1andOFF@
appearinthedisplay.
8. RepeatfromStep4abovetosettheEventforOFFinsteadofON.
9. PresstheENTERbuttontosetSunriseOFFforLoad2.Thewords
SET,ASTRO,ON/OFFEVENTS,LOAD2,andOFF@display.
10.RepeatfromStep4abovetosettheeventforOFFinsteadofON.
11.PresstheMODEbuttontoexitandadvancetosettingxed
timeevents.
5b – Setting SUNSET ON/SUNUP OFF Events
on Multi-Circuit Time Switches (ET8215C)
1. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewords
SET,FIXED,ON/OFFEVENTandEVENT01appearonthe
display.
2. Ifnecessary,presstheENTERbuttontodisplayON@orOFF@
(dependingonwhatyouwanttoset).
3. PresstheDAYbuttontodisplay12:00amandalldaysofthe
week.
4. Pressthe+or– buttonstoenterthetimeyouwanttoset.
NOTE: To go from AM to PM, keep pressing the +or
– buttons to cycle through the day. You can hold the+or
– buttons down for 3 seconds to make the time scroll
quickly.
5. IfyouwanttheEventtooccurforacombinationofdaysrather
thaneveryday(e.g.,weekendsonly,weekdaysonly,orindividu-
aldays),presstheDAYbuttonagainasnecessarytocycle
throughtheindividualdaysorcombinationofdaysyouwant.
6 – Setting Fixed Timed Events
Setting Sunset ON / Fixed Time OFF
Experienceintheeldhasshownthatisthemostcommonlyused
settingfortheTimeSwitch.Theseinstructionscovertheentire
procedure.
1. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewords
SET,ASTRO,andON/OFFEVENTSappearintheupperareaof
thedisplay.
2. PresstheENTERbuttonifnecessarytodisplayON@.
3. MakesureyouknowwhichdaysyouwanttheSunsetON
eventtobeactive.
- IfyouwanttheEventtoturnONeverydayoftheweek,
presstheDAYbuttontodisplaySUNSETandalldays.
- IfyouwanttheEventtoturnONforadifferentcombination
ofdays,presstheDAYbuttonagainasnecessarytocycle
throughthedaysorcombinationofdaysyouwant.
To remove an individual day, press the DAY button until
the day is blinking, then press the – button.
4. PresstheMODEbuttonasnecessarytodisplaySET,FIXEDand
ON/OFFEVENT.
5. PresstheENTERbuttonasnecessarytodisplayOFF@and
EVENT02.
6. PresstheDAYbuttontodisplay12:00amandalldaysofthe
week.
7. Pressthe+or– buttonstoenterthetimeyouwanttoset.
To go from AM to PM, keep pressing the +or– buttons to
cycle through the day. You can hold the+or– buttons down
for 3 seconds to make the time scroll quickly.
8. IfyouwanttheEventtooccurforacombinationofdaysrather
thaneveryday(e.g.,weekendsonly,weekdaysonly,or
individualdays),presstheDAYbuttonagainasnecessaryto
cyclethroughtheindividualdaysorcombinationofdaysyou
want.
NOTE: To choose a combination not shown during
cycling (e.g., Tuesday and Thursday), you must create an
individual event for each of the days you want.
6. ET8215C ONLY—Foramulti-circuitdevicewithloadsset
independently,youcanchoosetheloadyouwanttheeventto
control.Thedefaultsettingisforbothloads,asyoucanseeon
thedisplay.PresstheON/OFFbuttonunderaloadtoremove
theloadfromtheevent.
7. Whenyouhavesettheeventcorrectly,youhavetwochoices:
- PresstheENTERbuttontosetthenextxedtimeevent(up
to28events).
- PresstheMODEbuttontoexit.
PresstheMODEbuttonrepeatedlytoselectthedesiredoperating
modeonthedisplay.Thereare2options:
• AUTO—wheretheTimeSwitchfollowstheeventsyouhavepro-
grammed,turningthecircuitsONandOFFatthetime(s)set.
NOTE: You can override programmed events and force the
Time Switch ON or OFF by pressing theON/OFF button.
• MANUAL—whereanyeventssetaredisabledandtheTime
SwitchcontrolsallcircuitsthroughtheON/OFFbutton.
NOTE: You can review or edit any programmed events at any time
by pressing the MODE button repeatedly to return to the appropriate
menu, then following programming instruction provided on this sheet.
Operating the Time Switch
Usethisproceduretoclearthesettingsprogrammedforanevent.
1. Ifnecessary,presstheMODEbuttonrepeatedlyuntilthewords
SET,FIXED,andON/OFFEVENTSareshownonthedisplay.
2. PresstheENTERbuttonasnecessarytocyclethroughevents
thathavebeensetuntilyouseetheeventyouwanttodelete.
3. Pressthe+or– buttonsATTHESAMETIMEtodisplay--:----.
4. PresstheMODEbuttontoexit.
OPTIONAL – Deleting (Clearing) an Event
LIMITED ONE-YEAR WARRANTY
If within the warranty period specified, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace
it, at its sole option, free of charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply
to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been subject to
unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of
the product; (e) sealed lamps and/or lamp bulbs, LED’s and batteries; (f) the finish on any portion of the product, such as surface and/or weathering, as
this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY
AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME
STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) completing a warranty claim
on line at www.intermatic.com. This warranty is made by: Intermatic Incorporated, Customer Service 7777 Winn Rd. Spring Grove, Illinois 60081-9698.
For warranty service go to: http://www.intermatic.com or call 815-675-7000.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
158--00992
• BatteriescanbeeasilyreplacedwithoutremovingtheTime
Switchmechanismoreldwiring.
• Pressinanddownward(inthedirectionofthearrows)onthe
batterycover.
• Itisrecommendedtoreplacethebatteriesevery2-3yearswith
2AAAindustrialgradealkalinecellsaspartofnormalmainte-
nanceontheTimeSwitch.
• Besuretoobservebatterypolaritymarkingswheninstalling
batteries.
• Nootherbatterymaintenanceisrequired.
Battery Maintenance
NOTE: To choose a combination not shown during cycling
(e.g., Tuesday and Thursday), you must create an individu-
al event for each of the days you want.
9. ET8215 ONLY—Foramulti-circuitdevicewithloadsset
independently,youcanchoosetheloadyouwanttheeventto
control.Thedefaultsettingisforbothloads,asyoucanseeon
thedisplay.PresstheON/OFFbuttonunderaloadtoremovethe
loadfromtheevent.
10.Whenyouhavesettheeventcorrectly,youhavetwochoices:
- PresstheENTERbuttontosetthenextxedtimeevent(upto
28events).
- PresstheMODEbuttontoexit.

Navigation menu