Intermec Technologies 05CN3 CN3 User Manual SAC Requirements for Customer ation
Intermec Technologies Corporation CN3 SAC Requirements for Customer ation
Contents
Compliance Insert
CN3 Compliance Insert
For Users in the United States and Canada
For Users Outside of the United States or Canada
Caution: This marking indicates that the user should read all included
documentation before use.
This product conforms to the following approvals. The users of this product are
cautioned to use accessories and peripherals approved by Intermec Technologies
Corporation. The use of accessories other than those recommended, or changes to
this product that are not approved by Intermec Technologies Corporation, may void the
compliance of this product and may result in the loss of the user’s authority to operate
the equipment.
Class B Compliant Products
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the radio or television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-
Causing Equipment Regulations.
Document Number: 632194 Rev: A Page 1 of 4
Caution: The battery pack used in this device may ignite, create a
chemical burn hazard, explode, or release toxic materials if mistreated.
Do not incinerate, disassemble, or heat above 100°C (212°F). Charge
only with Intermec Models AC14, AD10, AD11, AD12 or AV6. Do not
short circuit; may cause burns. Keep away from children.
Use only Intermec battery pack Model AB8 or AB9. Use of incorrect
battery pack may present a risk of fire or explosion. Promptly dispose
of used battery pack according to the instructions.
Battery Recycling Information
This product contains or uses a lithium ion (Li-ion) main battery. When
the battery reaches the end of its useful life, the spent battery should be
disposed of by a qualified recycler or hazardous materials handler. Do
not mix this battery with the solid waste stream. Contact your Intermec
Technologies Service Center for recycling or disposal information.
Note: In the U.S.A., the EPA does not consider spent Li-ion batteries as hazardous
waste.
Caution: For Power Supply use Intermec Model (list model number(s)
here). No user-serviceable parts.
Specific Absorption Rate (SAR)
Radio Wave Exposure and Specific Absorption Rate (SAR) Information for Model CN3
Configurations with 802.11g Radio
The FCC permits a maximum SAR value of 1.6 W/kg. For body worn operation, the highest SAR
value for the Model CN3, as tested by BABT, is 0.087 W/kg.
The FCC permits a maximum SAR value of 1.6 W/kg. For head worn operation, the highest SAR
value for the Model CN3, as tested by BABT, is 1.031 W/kg.
This product has been tested and meets the FCC RF exposure guidelines when used with the
Intermec accessories supplied or designated for this product. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines.
Radio Wave Exposure and Specific Absorption Rate (SAR) Information for Model CN3
Configurations with GSM/GPRS Radio
For residents of Canada and the United States and other countries/regions that have adopted the
SAR limit recommended by Industry Canada RSS-102 and Federal Communications Commission
Office of Engineering and Technology (OET) Bulletin 65, the maximum allowed SAR value is
1.6W/kg over 1g of tissue. For use at the ear, the highest SAR value for the Model CN3, as tested
by BABT, is 0.528 W/kg. For body worn operation, the highest SAR value for the Model CN3, as
tested by BABT, is 0.543 W/kg.
Document Number: 632194 Rev: A Page 2 of 4
This product has been tested and meets the FCC RF exposure guidelines when used with the
Intermec accessories supplied or designated for this product. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines.
Radio Wave Exposure and Specific Absorption Rate (SAR) Information for Model CN3
Configurations with GSM/GPRS Radio
For residents of the European Union and other countries/regions that have adopted the
International Commission on Non-Ionizing Radiation Protection (ICNIRP) SAR limit, the maximum
allowed SAR value is 2.0W/kg over 10g of tissue. For use at the ear, the highest SAR value for the
Model CN3, as tested by BABT, is 0.369 W/kg. For body worn operation, the highest SAR value for
the Model CN3, as tested by BABT, is 0.292 W/kg.
This product has been tested and meets the FCC RF exposure guidelines when used with the
Intermec accessories supplied or designated for this product. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines.
Laser and Imager Compliance and Precaution (Rest of World)
This product complies with the following standards for LED safety:
IEC 60825-1 / EN 60825-1 - Class 1 LED Product
Important Radio Information
For Users in the United States and Canada
Place this supplement in your manual.
This device complies with Part 15 of the FCC rules and with RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received,
including interference that can cause undesired operation.
Caution: Changes or modifications not expressly approved by Intermec
could void the user’s authority to operate this equipment
For Users Outside the United States and Canada
Intermec Technologies Corporation declares that this module is in compliance with the
essential requirements and other relevant provisions of R&TTE Directive (1999/5/EC).
Document Number: 632194 Rev: A Page 3 of 4
The transmitter module’s output power is 646 mW. The products using this module are
intended for business and industrial environments. They should not be used in
residential environments and by children.
This product is marked with this logo and uses radio frequency
bands that are not harmonized throughout the European
Community.
The following table indicates the areas of intended use of the equipment and any
known restrictions.
Country of License
Intended Use Yes No Required Restrictions Details
Austria X
Belgium X
Cyprus X
Czech Republic X
Denmark X
Estonia X
Finland X
France X X
Outdoor frequency operation restricted to
2446.5 MHz to 2483.5 MHz
Germany X
Greece X
Hungary X
Ireland X
Italy X
Lithuania X
Latvia X
Luxembourg X
Malta X
The
Netherlands X
Poland X
Portugal X
Slovakia X
Slovenia X
Spain X
Sweden X
United Kingdom X
Country of License
Intended Use Yes No Required Restrictions Details
Other non-EU:
Iceland X
Liechtenstein X
Norway X
Switzerland X
Document Number: 632194 Rev: A Page 4 of 4