Intermec Technologies IM4 IM4 User Manual

Intermec Technologies Corporation IM4 IM4 Integration Guide

a href="https://usermanual.wiki/Intermec-Technologies" itemprop="url"> Intermec Technologies >

Users Manual

578-100-137   Revision A     Page 1 of  1 *578-100-137A*   *578-100-137A* Compliance Statement Insert  Device Name:  RF Identification Serial Radio Module  Model Number:   IM4    FCC ID:  EHAIM4  The responsible party for the compliance of this device is:  Intermec Technologies Corporation  6001 36th Avenue West   Everett, WA  98203  USA  (425) 348-2600  This product conforms to the following approvals.  The user(s) of this product are cautioned to use accessories and peripherals approved by Intermec Technologies Corporation.  The use of accessories other than those recommended, or changes to this product that are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the users authority to operate the equipment.  This device complies with Part 15 of the FCC Rules, and the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  FCC Digital Emissions Compliance     This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  •  Reorient or relocate the radio of television receiving antenna. •  Increase the separation between the computer equipment and receiver. •  Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected. •  Consult the dealer or an experienced radio television technician for help.  Canadian Digital Apparatus Compliance   This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.     Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.   Warning:  per the FCC and Canadian RF (radio frequency) exposure requirements,  1)  Antennas must be supplied and installed as recommended by Intermec Technologies Corporation to ensure compliance to RF exposure requirements.  The antennas approved for use are listed in the Intermec accessories guide for the IM4 PC Card.  Correct antenna mounting is fully described within the Intermec IM4 PC Card Users Guide. 2)  When installing and using Intermec Technologies Corporation-approved remote antennas associated the RFID reader, a 20-cm (8-inch) passing distance must be maintained from any body part of the user, or near by persons, and the remote antenna.  The antenna must not be touched during transmitter operation. 3)  Cables attached to the remote antennas must have a minimum length as provided from Intermec Technologies Corporation to insure the proper losses to control RF exposure. 4)  RF safety requirements mandate this device cannot be co-located with other transmitters unless such co-location is specifically approved by the FCC. 5)  Integrators of the radio module are obligated to pursue regulatory approval and labeling of this transmitter under FCC Part 2 and Part 15 rules.  Industry Canada approval and labeling requirements must be met for marketing of the integrated product in Canada.    Warning: Per Canadian RF exposure requirements, 1)    The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website   www.hc-sc.gc.ca/rpb
Download:
Mirror Download [FCC.gov]
Document ID595116
Application IDIclOM30mJQHUdqp5hHqBWw==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize38.92kB (486532 bits)
Date Submitted2005-10-24 00:00:00
Date Available2005-10-24 00:00:00
Creation Date2005-10-18 10:40:36
Producing SoftwareAcrobat Distiller 6.0.1 (Windows)
Document Lastmod2005-10-19 07:55:54
Document TitleIP4_Handheld Instructions
Document CreatorPScript5.dll Version 5.2
Document Author: smithles
FCC ID Filing: EHAIM4

Navigation menu