Intermec Technologies ITRM24501 Intellitag RFID Radio User Manual 011214L1

Intermec Technologies Corporation Intellitag RFID Radio 011214L1

Contents

Appendix L

Intermec Technologies Corporation REPORT NO: 011214-1
EMC Test Laboratory DATE: December 14, 2001
DOC. NO.: 577-501-006 Page 1 of 2
ITRM24501 Radio Module, FCC 15.247, Canada RSS-210, RSS-102 FCC ID: EHAITRM24501
APPENDIX L, Users Manual and DoC insert
Technologies Corporation
EMC Test Laboratory
Cedar Rapids, IA
MEASUREMENT/TECHNICAL REPORT
Intermec Technologies Corporation
Intellitag ITRM24501 Radio Module
2450 MHz Spread Spectrum Transmitter
REPORT NO: 011214-1
DATE: December 14, 2001
APPENDIX L
COMPLIANCE INSERT, USER INFORMATION
FOR THE ITRM24501 RADIO MODULE
578-100-0xx Revision A Page 1 of 1
*578-100-0xx*
*578-100-0xx*
Compliance Statement Insert
Device Name: RF Identification Radio Module Model Number: ITRM24501
FCC ID: EHAITRM24501
The responsible party for the compliance of this device is: Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203 USA
(425) 348-2600
This product conforms to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals
approved by Intermec Technologies Corporation. The use of accessories other than those recommended or changes to this product
that are not approved by Intermec Technologies Corporation may void the compliance of this product and may result in the loss of
the users authority to operate the equipment.
This device complies with part 15 of the FCC and Industry Canada Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
FCC Digital Emissions Compliance
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment is a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Canadian Digital Apparatus Compliance
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
WARNING: per the FCC and Canadian RF (radio frequency) exposure requirements,
(1) Antennas must be supplied and installed as recommended by Intermec Technologies to ensure compliance to RF exposure
requirements. The antennas approved for use are Intermec part numbers 805-605-001 and 805-576-101. Correct antenna
mounting is fully described within the Intermec ITRM24501 Users Guide.
(2) When installing and using Intermec approved remote antennas associated the RFID tag reader, a 20-cm (8-inch) passing
distance must be maintained from any body part of the user or near by persons and the remote antenna. The antenna must not
be touched during transmitter operation.
(3) Cables attached to the remote antennas must have a minimum length as provided from Intermec to insure the proper losses to
control RF exposure.
(4) RF safety requirements mandate this device cannot be co-located with other transmitters.
WARNING CANADA USERS: To prevent radio interference to the licensed service, this device is intended to be operated indoors
and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to
licensing. The end user is responsible to obtain the license.

Navigation menu