Intermec Technologies RC12ABGN WLAN board User Manual
Intermec Technologies Corporation WLAN board
User Manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2048651 |
| Application ID | ncwEcKMEgN8h95Tk78LSTQ== |
| Document Description | User Manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 62.89kB (786089 bits) |
| Date Submitted | 2013-08-20 00:00:00 |
| Date Available | 2013-08-20 00:00:00 |
| Creation Date | 2013-08-13 17:32:38 |
| Producing Software | Microsoft® Office Word 2007 |
| Document Lastmod | 2013-08-13 17:36:20 |
| Document Title | User Manual.pdf |
| Document Creator | Microsoft® Office Word 2007 |
| Document Author: | AmyChou |
Model:
RC12ABGN
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1)
The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2)
The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is
still responsible for testing their end-product for any additional compliance requirements required with this module
installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be
maintained between the antenna and users. The final end product must be labeled in a visible area with the following:
âContains FCC ID:EHA-RC12ABGNâ. The grantee's FCC ID can be used only when all FCC compliance requirements are
met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF
module in the userâs manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Annotate, Fill forms Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2013:08:13 17:32:38Z Creator Tool : Microsoft® Office Word 2007 Modify Date : 2013:08:13 17:36:20+08:00 Metadata Date : 2013:08:13 17:36:20+08:00 Format : application/pdf Creator : AmyChou Producer : Microsoft® Office Word 2007 Document ID : uuid:5044dc09-badc-4b6d-9443-8b37b7f936d0 Instance ID : uuid:f6411bd9-506e-4784-a566-31029f100dd9 Page Count : 8 Language : zh-TW Author : AmyChouEXIF Metadata provided by EXIF.tools