Intermec Technologies RM915P PCMCIA LAN Card User Manual 050215 2
Intermec Technologies Corporation PCMCIA LAN Card 050215 2
User Man
Intermec Technologies Corporation
EMC Test Laboratory
MN RM160, FCC 15.247, C2PC
APPENDIX C
INFORMATION TO THE USER
Compliance Statement Insert
Device Name: Hand-held Computer Model Number: 6400
The responsible party for the compliance of this device is: Intermec Technologies Corporation
6001 36th Avenue West
Everett, WA 98203 USA
(425) 348-2600
CAUTION: See users guide instructions for handling, charging, and replacing batteries. Failure to follow those instructions can result
in personal injury, fire, or battery explosion.
This product complies to the following approvals. The user(s) of this product are cautioned to use accessories and peripherals
approved by Intermec Technologies Corporation. The use of accessories other than those recommended, or changes to this product that
are not approved by Intermec Technologies Corporation, may void the compliance of this product and may result in the loss of the
users authority to operate the equipment.
FCC Digital Emissions Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the radio of television receiving antenna.
• Increase the separation between the computer equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the radio or television receiver is connected.
• Consult the dealer or an experienced radio television technician for help.
Canadian Digital Apparatus Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
FCC Spread Spectrum Transmitter Compliance
This device is also certified to operate under Part 15, Subpart C, Section 15.247 of the FCC rules for Intentional Radiation Products. This certification includes
Docket 87-389 covering rules effective June 1994. It may not cause interference to authorized radio communication devices, and must accept any interference
caused by those devices.
Canadian RSS-210 Spread Spectrum Transmitter Compliance
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
WARNING: per the FCC and Canada RF (radio frequency) exposure requirements,
1) Only the antenna supplied and installed with this unit by Intermec Technologies is to be used with this computer terminal. The product is configured to
ensure compliance to FCC and Canada RF exposure requirements.
2) The user shall not touch the terminal top (antenna) and is to remain 20-cm (8 of and inches) from the antenna while the transmitter is in use. The radio
cannot be co-located with any other transmitter.
Antenna Requirements
FCC rules section 15.203 and Canada RSS-210 require that this device be operated using an antenna furnished by Intermec Technologies Corporation. The
antenna coupling on this product has been designed to accept only antennas manufactured by Intermec Technologies. Use of an antenna other than that furnished
with the equipment is prohibited by FCC and Industry Canada rules.
European Notice
The 902-928 MHz Spread Spectrum Transmission (SST) radio referred to in accompanying documentation is not available for sale in Europe (including, but
not limited to, Great Britain, Italy, Germany, France, Spain, Norway, Denmark, Sweden, Finland, Portugal, and the Benelux countries). Any references to 902-928
MHz SST, or modules containing 902-928 MHz SST radios, should be disregarded by the users of this product in Europe.
DOC. NO.: 577-501-251
REPORT NO: 050215-2
Page 23 of 23