Intermec Technologies UAPRFID-900 User Manual Manual Supplement

Download:
Mirror Download [FCC.gov]
Document ID	92286
Application ID	O+phkGAvQy+JXX20QBxk2w==
Document Description	Revised User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	1.43kB (17915 bits)
Date Submitted	2000-03-20 00:00:00
Date Available	2000-03-21 00:00:00
Creation Date	2000-03-20 10:05:17
Producing Software	Acrobat PDFWriter 3.02 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	Manual Supplement

P/N 06XXXX-001
Important 2100 Information!
(For 900 MHz and 2.4 GHz RFID Modules)
Contents
For Users in the United States and Canada....................................................................................2
2100 Manual Supplement
For Users in the United States and Canada
Place this supplement in your manual.
This device complies with Part 15 of the FCC Rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that can cause undesired
operation.
Federal Communications Commission Compliance
This equipment is intended for operation in a commercial environment, in
compliance with the requirements for a Class A digital device, pursuant to Part
15 of the FCC Rules, and it must not be used in a residential environment;
however, it has also been tested and found to comply with the more stringent
requirements for a Class B device, pursuant to Part 15 of the FCC Rules. It
generates, uses, and can radiate radio frequency energy. If not installed and
used in accordance with the instruction manual, it may cause interference to
radio communications. If this equipment causes interference, the user will be
required to correct the interference at the user’s own expense.
Note: In order to maintain compliance with FCC Rules, the input/output (I/O) cables
that interconnect between the device and any peripheral must be as specified by
Intermec.
Installation Warning:
FCC regulations limit exposure to radiofrequency (RF) radiation. To comply
with these regulations, this device must be installed in such a way that the
operators of this device will not be closer than 20 cm (8 inches) from the cover
on the antenna assembly under normal operation conditions. While the device
is operating, the operator’s body and parts of the body such as eyes, hands,
or head, must be 20 cm (8 inches) or farther from the cover of the antenna
assembly.
The installer should also protect him/herself from RF exposure by not
operating the device while they are closer than the distance mentioned above.
FCC regulations also require that the antenna assembly of this device be
installed in accordance with the installation procedures in this manual to allow
the operator to comply with this limit.
Operator Warning:
FCC regulations limit exposure to radiofrequency (RF) radiation. To comply
with these regulations, the operators of this device must maintain adistance of
at least 20 cm (8 inches) from the cover on the antenna assembly under normal
operation conditions. While the device is on, the operator’s body and parts of
the body such as eyes, hands, or head, must be 20 cm (8 inches) or farther
from the cover of the antenna assembly.
2100 Manual Supplement
For Users in the United States and Canada (cont.)
Industry Canada Compliance
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
This device requires a radio license, unless it is used totally inside a building.
(The user must obtain this license.)
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Cet appareil exige une license radio à moins d’être entièrement installé dans un
bâtiment. (L’utilisateur doit obtenir cette license.)
Safety Agency Approvals
This device is UL Listed and CSA Certified.
Caution
Changes or modifications not expressly approved by Intermec could void the
user’s authority to operate this equipment.
P/N 06XXXX-001


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 4
Creator                         : 
Create Date                     : 2000:03:20 10:05:17
Title                           : Manual Supplement
Author                          : 
Producer                        : Acrobat PDFWriter 3.02 for Windows NT
Subject                         : 

EXIF Metadata provided by EXIF.tools