Invacare 1036793 Users Manual 1040101
1036794 1040101
1036794 to the manual ea016aaf-e635-49ee-abde-c3d3dd564365
2015-02-02
: Invacare Invacare-1036793-Users-Manual-433090 invacare-1036793-users-manual-433090 invacare pdf
Open the PDF directly: View PDF 
.
Page Count: 8
| Download | |
| Open PDF In Browser | View PDF |
Space Saver / Conventional Arm Socket Assemblies Assembly, Installation and Operating Instructions Kit Numbers 1036793, 1036794, 1094952, 1094953 FRONT ARMREST SOCKET NOTE: Check all parts for shipping damage before us- REPLACEMENT/H-BLOCK ing. In case of damage, DO NOT use the equipment. INSTALLATION (FIGURE 1) SAVE THESE INSTRUCTIONS Contact the Dealer/Carrier for further instructions. 1. Remove the locknut and screw securing the H-block to the right and left front frames (FIGURE 1). SAFETY SUMMARY 2. Remove the H-blocks. The following recommendations are made for the safe use of the Space Saver/ Conventional Arm Socket Assemblies: NOTE: It may be necessary to reposition the wheel lock assembly before/after installing the new front armrest sockets/H-Blocks. GENERAL WARNING 3. Position the NEW armrest socket/H-Block onto the right and left front frames by performing one (1) of the following: DO NOT install or use this equipment without first reading and understanding these instructions. If you are unable to understand the Warnings, Cautions or Instructions, contact a healthcare professional, dealer or technical personnel before attempting to install this equipment - otherwise, injury or damage may occur. NOTE: Armrest sockets/H-Block MUST be positioned in the 1st or 2nd mounting hole on the right and left front frames depending on the type of wheelchair. INSTALLATION WARNING A. MVP/STYLE 14 through 16 inches deep - Align the mounting hole in the H-block with the first mounting hole on front of chair. After ANY adjustments, repair or service and BEFORE use, make sure that all attaching hardware is tightened securely. B. ALL type wheelchairs 17 and 18-inch deep - Align the mounting hole on the H-block with the second mounting hole on front of chair. Armrest Socket/ H-Blocks PURPOSE To replace existing half-arms or install new FIXED or ADJUSTABLE arms on Invacare MVP and STYLE wheelchairs built after 10-10-92. Mounting Holes The Invacare MVP or STYLE can be fitted with Space Saver or Conventional mounting brackets with either fixed oradjustable arms. These arms can be used on all chairs 14 through 18 inches. Mounting Holes Front Frames FIGURE 1 - FRONT ARMREST SOCKET REPLACEMANT/H-BLOCK INSTALLATION 1 3. Position the armrest spacer flush against the inside of the outside armrest bracket as shown in “DETAIL A”, FIGURE 2. REAR ARMREST SOCKET INSTALLATION ON WHEELCHAIRS BUILT BEFORE 7/00 4. Place the armrest socket into the groove of the armrest spacer. Space Saver Armrest Sockets (FIGURE 2) 5. Position inside armrest bracket against the armrest socket (FIGURE 2). Space Saver Kit No. 1036793 Includes the following: DESCRIPTION QTY. Left Outside Armrest Bracket Left Inside Armrest Bracket Left Armrest Spacer Right Outside Armrest Bracket Right Inside Armrest Bracket Right Armrest Spacer Front Armrest Socket Rear Armrest Socket Tube Supports Hex Screw Locknuts 6. Loosely secure the brackets, armrest socket and armrest spacer together using one (1) of the six (6) hex screws and a locknut. 1 1 1 1 1 1 2 2 2 8 8 7. Position the armrest bracket on the rear frame making sure that the armrest spacer is positioned on the outside of the rear armrest socket. Refer to Detail “A” in FIGURE 2. 8. Secure the assembly of the chair frame using two (2) of the six (6) hex screws and locknuts. CAUTION Make sure that all screws and locknuts are secure at all times. 1. Insert the tube support into armrest socket. 9. Repeat this procedure for the opposite side of the chair frame. NOTE: Tube support MUST be positioned below mounting hole. 2. Position the outside armrest bracket towards the outside of the chair frame. Right Outside Armrest Bracket Hex Screw Right Chair Frame Locknuts Outside Armrest Bracket Tube Support Inside Armrest Bracket Armrest Spacer Left Inside Armrest Bracket Left Chair Frame Right Inside Armrest Bracket Locknuts DETAIL “A” TOP VIEWS Right Left Left Outside Armrest Bracket Tube Support Rear Armrest Socket INSIDE OUTSIDE OUTSIDE Mounting Hole Hex Screws Armrest Spacer Rear Armrest Socket Armrest Spacers FIGURE 2 - REAR ARMREST SOCKET INSTALLATION - SPACE SAVER ARMS 2 Conventional Armrest Sockets (FIGURE 3) 4. Place the armrest socket into the groove of the armrest spacer. Conventional Kit No. 1036794 includes the following: DESCRIPTION QTY. Left Outside Armrest Bracket Left Inside Armrest Bracket Left Armrest Spacer Right Outside Armrest Bracket Right Inside Armrest Bracket Right Armrest Spacer Front Armrest Socket Rear Armrest Socket Tube Supports Spacer Long Hex Screw Short Hex Screw Locknuts 5. Position the bracket spacer flush against the inside of the outside armrest bracket. 1 1 1 1 1 1 2 2 2 2 2 6 8 6. Position inside armrest bracket against the bracket spacer. 7. Loosely secure the brackets, armrest socket, armrest spacer and bracket spacer together using one (1) of the two (2) long hex screws and a locknut. 8. Position the armrest bracket on the rear frame making sure that the armrest spacer is positioned on the outside of the rear armrest socket. Refer to DETAIL “A” in FIGURE 1. 9. Secure the assembly of the chair frame using two (2) of the four (4) short hex screws and locknuts. CAUTION 1. Insert the tube support into armrest socket. NOTE: Tube support MUST be positioned below mounting hole. Make sure that all screws and locknuts are secure at all times. 2. Position the outside armrest bracket towards the outside of the chair frame. 10. Repeat this procedure for the opposite side of the chair frame. 3. Position the armrest spacer flush against the outside of the outside armrest bracket as shown in “DETAIL A”, FIGURE 3. Tube Short Hex Support Screw Mounting Hole Right Outside Rear Armrest Armrest Bracket Socket Right Chair Frame Outside Armrest Bracket Long Hex Screw Inside Armrest Bracket Armrest Spacer Left Chair Frame Locknuts Left Outside Armrest Bracket Short Hex Screws Right Inside Armrest Bracket Bracket Spacer DETAIL “B” TOP VIEW Left Left Inside Armrest Bracket Tube Support Right INSIDE OUTSIDE OUTSIDE Armrest Spacer Bracket Spacer Mounting Hole Rear Armrest Socket Long Hex Screw Armrest Spacers FIGURE 3 - REAR ARMREST SOCKET INSTALLATION - CONVENTIONAL ARMS 3 2. Install armrest bracket onto wheelchair frame and secure using short hex screw and locknut. Securely tighten. REAR ARMREST SOCKET INSTALLATION ON WHEELCHAIRS BUILT AFTER 7/00 Space Saver Armrest Sockets (FIGURE 4) 3. Insert the tube support into the armrest socket ensuring that the holes in the tube support align with the holes in the armrest socket. Space Saver Kit No. 1094952 includes the following: 4. Install the armrest socket into the armrest bracket. DESCRIPTION Armrest Brackets Front Armrest Sockets Rear Armrest Sockets Tube Supports Nylon Washers Long Hex Screw Short Hex Screw Locknuts Hex Locknut QTY. NOTE: Mounting hardware must be installed in the oreintation shown in FIGURE 4. 2 2 2 2 4 2 6 6 2 5. Install short hex screw through armrest bracket, washer, armrest socket, tube support, washer and armrest bracket as shown in FIGURE 4. 6. Secure with locknut. 7. Install remaining short hex screw (used as armrest stop) through armrest bracket and secure with locknut. 1. Position armrest bracket into mounting position. Refer to Owner’s Manual, supplied with the wheelchair, for proper mounting positions. MOUNTING HOLES Armrest Socket 8. Repeat this procedure for the opposite side of the chair frame. Tube Support Armrest Socket Short Hex Screw Armrest Stop Washer Armrest Bracket Armrest Bracket Wheelchair Frame Tube Support Armrest Socket Locknut Washer Armrest Bracket Short Hex Screw FIGURE 4 - REAR ARMREST SOCKET INSTALLATION ON WHEELCHAIRS BUILT AFTER 7/00 - SPACE SAVER ARMREST SOCKETS 4 1. Position armrest bracket into mounting position. Refer to Owner’s Manual for proper mounting positions. Conventional Armrest Sockets (FIGURE 5) Conventional Kit No. 1094953 includes the following: DESCRIPTION 2. Install armrest bracket onto wheelchair frame and secure using short hex screw and locknut. QTY. Armrest Bracket Bracket Spacer Front Armrest Socket Rear Armrest Socket Coved Armrest Spacer Tube Supports Nylon Washers Long Hex Screw Medium Hex Screw Short Hex Screw Locknuts Hex Locknut 2 2 2 2 2 2 2 2 2 2 4 2 3. Insert the tube support into the armrest socket ensuring that the holes in the tube support align with the holes in the armrest socket. 4. Install the armrest socket into the armrest bracket. NOTE: Mounting hardware must be installed in the oreintation shown in FIGURE 5. 5. Install long hex screw through armrest socket, tube support, coved armrest spacer, washer, armrest bracket, spacer and armrest bracket as shown in DETAIL “A”. NOTE: Ensure armrest socket is flush in coved spacer. 6. Secure with locknut. 7. Repeat this procedure for the opposite side of the chair frame. DETAIL “A” - TOP VIEW LEFT Tube Support RIGHT Armrest Socket Wheelchair Frame Hex Screw Spacer Coved Armrest Spacer Armrest Bracket Coved Armrest Armrest Spacer Bracket Spacer Tube Support Locknut Armrest Socket Long Hex Screw Short Hex Screw Washer Coved Armrest Spacer Wheelchair Frame FIGURE 5 - REAR ARMREST SOCKET INSTALLATION ON WHEELCHAIRS BUILT AFTER 7/00 - CONVENTIONAL ARMREST SOCKETS 5 Swing-Away Armrest (FIGURE 7) ARMREST OPERATION SWINGING AWAY. 1. Unlock the arm by rotating the release lever(s) towards the outside of the chair. CAUTION After any adjustments, make sure the locking mechanism is secured before using the wheelchair. 2. Pull the front of arm straight up/out of the socket and towards the rear of the chair. Adjustable Height Armrest (FIGURE 6) 3. To lock, push the arm towards the front of the chair; then downward and into the socket (unlocked). HEIGHT ADJUSTMENT. 1. Unlock the arm by flipping the height adjustment lever to the UP position. 4. When the arm is in place turn release lever towards the inside of the chair. REMOVING/INSTALLING. 1. Unlock the arm by rotating both release levers towards the outside of the chair. 2. Adjust the arm to the desired height. 3. Lock the arm by pressing the height adjustment lever into the DOWN position. 2. Pull arm straight up and out of the socket. REMOVING/INSTALLING. 1. Unlock the arm by rotating both release levers towards the outside of the chair. 3. Insert the arm straight down and into the socket. 4. Lock the arm by rotating both release levers toward the inside of the chair. 2. Pull arm straight up and out of the socket. 3. Insert the arm straight down and into the socket. Armrest Release Lever 4. Lock the arm by rotating both release levers toward the inside of the chair. Fixed Height Armrest (FIGURE 6) REMOVING/INSTALLING. 1. Unlock the arm by rotating both release levers towards the outside of the chair. 2. Pull arm straight up and out of the socket. 3. Insert the arm straight down and into the socket. 4. Lock the arm by rotating both release levers toward the inside of the chair. Unlock (Horizontal) Armrest Release Lever Armrest Release Lever Lock (Vertical) Height Adjustment Lever FIGURE 7 - ARMREST OPERATION SWING-AWAY ARMREST Armrest Release Lever FIGURE 6 - ARMREST OPERATION ADJUSTABLE/FIXED HEIGHT ARMREST 6 NOTES 7 Invacare Corporation USA One Invacare Way Elyria, Ohio USA 44036-2125 800-333-6900 www.invacare.com Canada 5970 Chedworth Way Mississauga, Ontario L5R 3T9, Canada 905-890-8838 Invacare and "Yes, you can" are trademarks of Invacare Corporation. © 2000 Invacare Corporation Form No. 93-29 Part No. 1040101 Rev B (1)10/00
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2001:02:20 08:00:22 Producer : Acrobat Distiller 4.0 for Windows Subject : 1040101 Author : CTHOMPSON2 Creator : Adobe PageMaker 6.52 Title : 1040101 Modify Date : 2001:02:20 08:00:27-05:00 Page Count : 8EXIF Metadata provided by EXIF.tools