Ioptron Smartstar Cube 8600 Users Manual A Series Instruction V2.1 8401
8603 to the manual e927daa5-d7e4-46e2-893b-223ef42f070e
2015-03-12
: Ioptron Ioptron-Smartstar-Cube-8600-Users-Manual-578699 ioptron-smartstar-cube-8600-users-manual-578699 ioptron pdf
Open the PDF directly: View PDF .
Page Count: 48
Download | ![]() |
Open PDF In Browser | View PDF |
® SmartStar®CubeTM-A Series Mount and Telescopes (For 8600, 8602, 8603 and 8604) Instruction Manual Table of Content Table of Content ............................................................................................................................. 2 1. SmarStar® CubeTM-A Series Overview....................................................................................... 4 1.1. SmartStar® CubeTM-A Series Features ............................................................................... 4 1.2. Assembly Terms .................................................................................................................. 6 2. Telescope Assembly................................................................................................................... 7 3. GoToNova® 8401 Hand Controller ........................................................................................... 10 3.1. Key Description.................................................................................................................. 10 3.2. The LCD Screen ................................................................................................................ 11 4. Getting Started.......................................................................................................................... 12 4.1. Level and Align the Mount ................................................................................................. 12 4.1.1. Level the Mount. ......................................................................................................... 12 4.1.2. Initial Positions............................................................................................................ 12 4.2. Setting Up the Mount ......................................................................................................... 12 4.2.1. Set Up Local Time and Site Info................................................................................. 13 4.2.2. Set Mount Type .......................................................................................................... 14 4.2.3. Set Anti-backlash........................................................................................................ 15 4.2.4. Using your telescope .................................................................................................. 16 4.2.5. Go to the Moon ........................................................................................................... 16 4.2.6. Initial Star Alignment................................................................................................... 17 4.3. Turn Off the Mount............................................................................................................. 17 5. Operate SmartStar® CubeTM-A mount in EQ Mode.................................................................. 18 6. Use SmartStar® CubeTM-A Telescopes .................................................................................... 20 6.1. Manual Operation of a Telescope ..................................................................................... 20 6.2. Slew to an Object............................................................................................................... 20 6.2.1. Planets, Sun, Moon .................................................................................................... 20 6.2.2. Deep Sky Objects ....................................................................................................... 20 6.2.3. Comets........................................................................................................................ 20 6.2.4. Asteroids ..................................................................................................................... 21 6.2.5. Stars............................................................................................................................ 21 6.2.6. Constellations ............................................................................................................. 21 6.2.7. User Objects ............................................................................................................... 21 6.2.8. Enter R.A. DEC........................................................................................................... 21 6.3. Sync to Target.................................................................................................................... 21 6.4. Electric Focuser ................................................................................................................. 21 6.5. Set Up Controller ............................................................................................................... 22 6.5.1. Set Up Local Time ...................................................................................................... 22 6.5.2. Set Up Site.................................................................................................................. 22 6.5.3. Set N/S Hemisphere ................................................................................................... 22 6.5.4. Set Display Contrast ................................................................................................... 22 6.5.5. Set Eyepiece Light...................................................................................................... 22 6.5.6. Set Backlight ............................................................................................................... 22 6.5.7. Set Anti-backlash........................................................................................................ 22 6.5.8. Set Key Beep .............................................................................................................. 22 6.5.9. Set Mount Type .......................................................................................................... 22 6.5.10. Reset All.................................................................................................................... 22 6.5.11. Update Firmware ...................................................................................................... 22 6.5.12. Set gear ratio ............................................................................................................ 22 6.5.13. Set Language ........................................................................................................... 23 6.6. Align ................................................................................................................................... 23 2 6.6.1. One Star Align ............................................................................................................ 23 6.6.2. Two Star Alignment .................................................................................................... 23 6.6.3. Three-Star Align.......................................................................................................... 23 6.6.4. Dis R.A axis error........................................................................................................ 23 6.6.5. Test Anti-backlash ...................................................................................................... 24 6.6.6. Polaris Position ........................................................................................................... 24 6.7. PEC Option ........................................................................................................................ 24 6.8. Set Up Tracking ................................................................................................................. 24 6.9. User Object List ................................................................................................................. 24 6.10. Auto Guide ....................................................................................................................... 24 6.11. Park Scope ...................................................................................................................... 24 6.12. To Park Position .............................................................................................................. 24 7. Maintenance and Servicing ...................................................................................................... 25 7.1. Maintenance ...................................................................................................................... 25 7.2. Storage and Transport....................................................................................................... 25 7.3. Troubleshooting ................................................................................................................. 26 7.4. iOptron Customer Service ................................................................................................. 27 Appendix A. Technical Specifications .......................................................................................... 29 Appendix B. GoToNova® 8401 HC MENU STRUCTURE ........................................................... 30 Appendix C. GoToNova® Star List................................................................................................ 32 Appendix D. Set Up USB-PC Connection .................................................................................... 38 Appendix E. Firmware Upgrade ................................................................................................... 45 Appendix F. Use a PC to Control an iOptron Mount .................................................................... 48 WARNING! NEVER USE A TELESCOPE TO LOOK AT THE SUN! Looking at or near the Sun will cause instant and irreversible damage to your eye. Children should always have adult supervision while observing. 2011.12.15 Ver 2.1 3 1. SmarStar® CubeTM-A Series Overview 1.1. SmartStar® CubeTM-A Series Features Alt-Azimuth Mount– The Cube™, with AltAzi/EQ dual application The SmartStar® Cubetm-A series come with our patented Alt-Azimuth (AltAzi) mount, a.k.a. The Cube™. This compact mount design is probably the most functional and flexible unit on the market. It was named “Hot Product 2008” by Sky and Telescope. Both axis motors are built into a small single unit with optical encoders which provides accurate GOTO and tracking. The mount is universally compatible with all telescopes using a dove-tail connection. In addition, there are no “dead spots” – so you can point your telescope to ANYWHERE above the horizon, whereas, other mounts block the telescope tube at certain points of rotation. This mount also comes standard with AC connection. An optional DC adaptor is available so you can plug your telescope mount into your car if you’re camping or at any remote location. With the integrated wedge and a standard counterweight, the A-series can also be operated as an German equatorial mount (EQ) for those who want to get familiar to or demonstrate a GOTO EQ mount operation. 32-Channel GPS Module All A-series telescopes come standard with a 32-channel GPS module for fully automated operation. Simply turn on the GoToNova® Hand Controller and the GPS module will automatically synchronize your telescope location and time with the GoToNova® computerized control system. View celestial objects without having to manually punch in the date, time, latitude or longitude. GoToNova® Computerized Control System The revolutionary GoToNova® computerized control system is by far the most technologically advanced automated tracking system available on the market today. With a database of 130,000 celestial objects, including all of the most famous galaxies, nebulae, star clusters, not to mention the planets, you’ll be able to enjoy star gazing with the simple push of a button. The easy to understand controller on the market The GoToNova® hand controller is much easier to use than other similar products. The hand controller is more intuitive with menu categories better organized. It also has a larger LCD screen with more lines of content compared with the competition. Using the easy-to-use hand controller and its large LCD screen, you can easily set up your telescope and select where you want to go. More precise speed control for viewing objects The 8401 hand controller comes with the A-series allows you to slew the telescope at 9 different drive speeds, keeping the object within the telescope’s viewfinder for as long as you wish. Compatible with many OTAs 4 Most light weight (<7lbs) Optical Tube Assembles (OTAs) with dovetail connection should be compatible with the SmartStar® CubeTM-A GOTO AltAzi mount. If you do not have a dovetail connection -- attach your OTA using mounting rings and dovetail available at your local telescope store or the OTA manufacturer. Contact iOptron for expert’s advice on compatibility issues. USB Port The 8401 hand controller equipped with a USB port that tremendously expands the functionalities of the already powerful system. With the USB2COM driver installed, the USB port works as an RS232 serial port. It supports firmware upgrades and computer control. With ASCOM protocol, you can control your telescope with most ASCOM compatible software. This enables you to utilize the CPU, large screen, and disk space of your PC/laptop. With a wide selection of software, your star gazing experience will never be the same again. Package Contents1 (1) SmartStar® CubeTM-A Mount with built-in GPS receiver (Models 8600, 8602, 8603 and 8604) (1) GoToNova® Hand Controller (Part No. 8401) (1) Controller Cable (1) USB Cable (1) Tripod with wedge (1) Tripod bolt and Tray Lock (1) Tripod Tray (1) AC adapter with cord For Model 8602 (SmartStar® CubeTM-A R80) (1) 80mm Refractor Telescope (2) Eyepieces (10mm & 25mm) (1) 3X Barlow Lens (1) 45º Diagonal For Model 8603 (SmartStar® CubeTM-A N114) (1) 114mm Newtonian Reflector Telescope (2) Eyepieces (10mm & 25mm) (1) Red Dot Finderscope For Model 8604 (SmartStar® CubeTM-A MC90) (1) 90mm Maksutov-Cassegrain Reflector Telescope (2) Eyepieces (10mm & 25mm) (1) Red Dot Finderscope (1) 45º Diagonal 1 The contents may vary from batch to batch. 5 1.2. Assembly Terms 1. Telescope tube 2. Dovetail lock 3. Hand controller 4. Altitude lock 5. Mount Polaris 6. Tripod 7. Tripod shaft 8. Tray 9. Tray lock 10. Azimuth lock screw 11. Wedge tilt screw 12. Tilt locks 13. Counterweight and shaft Zenith 5 10 13 11 12 7 8 9 Figure 1. Assembly Terms 6 6 2. Telescope Assembly Step 1. Preparing the Tripod 1. Extend tripod legs to full extension. 2. Slide tray on bottom of shaft (#7). Then screw on round black knob (#9). Step 2. Attaching the Mount 1. Raise wedge plate on the tripod by turning two tilt locks (12); 2. Attach mount to wedge plate using supplied azimuth lock screw (10). 3. lower wedge plate to it’s lowest position by turning the upper tilt lock upward while lightly push the mount down. Secure the mount by tightening the lower lock. Step 3a. Installing Batteries (not included) Note: you may use 8 AA batteries (Step 3) or the AC adaptor (Step 5) to operate the mount. Pull the batteries compartment cover (shown) open. Gently pull the batteries holder (shown next) out of the compartment to avoid breaking the attached wires. Step 3b. Insert 8 AA batteries (not included) according to the diagrams on the holder. Refer to the diagram on the holder to orient the batteries properly. Replace the holder back into the batteries compartment and replace the cover. For reference: the battery pack fits in with wires on the bottom right (See arrow in photo). Use only fresh batteries. Using/mixing old or low batteries may cause error messages. Optional AC Adapter and Car Charger accessories are available at www.ioptron.com Step 4. Attaching Telescope Attach telescope to mount using the dovetail lock knob (#2). Dovetail lock (#2) (Picture shows 80mm refractor. However all scopes will attach in the same manner.) 7 Step 5. Plug in hand controller and AC adaptor. Plug hand controller into either one of the two HBX ports on the mount. Next plug in AC adaptor. (Or use batteries—see step 3). Turn on power (the red light should go on). At this point you can begin observing manually. Use the 4 Arrow keys (▲▼◄►) to rotate the scope Up, Down, Left, and Right. Use the SPEED key to change the slew rate from the slowest (2X) to the fastest (MAX). The other HBX is reserved for accessories, such as external GPS module, electronic focuser or laser pointer. DO NOT plug non-iOptron accessories into the unit to avoid damaging the mount or accessories. For 80mm Refractor (#8502)……..................................................... Insert 45º diagonal: Insert the diagonal into the eyepiece side of the telescope. Tighten the thumbscrews to a firm feel only. Plug in AC adaptor here 45º diagonal eyepiece Insert the eyepiece: Slide the eyepiece into the open end of the diagonal. Tighten the thumbscrews to a firm feel only. Remove the dust cover from the other end of optical tube assembly. Use the focus knob to bring objects into focus. You may need to turn the focus knob quite a few turns to focus your telescope for the first time. Always start observing using a low power eyepiece (such as a 25mm eyepiece) to get a Focus knob nice wide field of view. Later you can change to high power if so desired. Higher powered eyepieces have a much narrower field of view. So it’s more difficult to initially locate objects using higher powered eyepieces. For 114mm Newtonian (#8503) ……................................................. Attach the red dot finder scope to the telescope tube (#1): Point toward open First remove the two washers on the tube. Then place the end of telescope finder scope onto the two bolts and re-attach the washers securely. The finder scope should face towards the open Bolts end of the tube (see arrow in diagram). Turn on the beam using the switch on the side. (note: you may need to remove the plastic insulation placed next to the battery underneath) Switch 8 For 90mm Maksutov-Cassegrain (#8504)…………………………………. Diagonal Eyepiece Install Diagonal by screwing it onto the back end of the scope. You can adjust the position of the diagonal by loosening the free-spinning threader on the diagonal. Install the Finderscope by sliding the dovetail plate onto the sleeve (see arrow) and tightening the side screw. The eyepiece can be placed on the end of the scope or on the side (see next step). Secure the eyepiece using the side screw. Use the focus knob to adjust the focus. Flip switch This picture shows the eyepiece on the side. Remove the protective cap to insert the eyepiece. The diagonal is not used for side viewing. Use the flip switch to flip the internal mirror to view from the side or the end of the scope. 9 3. GoToNova® 8401 Hand Controller HBX Port USB Port Figure 1. GoToNova 8401 Hand Controller GoToNova® 8401 hand controller (HC) is the standard controller for a SmartStar® Cube -A series mount and telescope, as shown in Figure 1. (The earlier version equipped with a 8402 hand controller. Contact iOptron for instruction.) TM 3.1. Key Description • • • • • MENU: Press “MENU” to enter the Main Menu. BACK: Move back to the previous screen, or end/cancel current operation, such as slewing. ENTER: Confirm an input, go to the next menu, select a choice, or slew the telescope to a selected object. Arrow (▲▼►◄): Press ▲▼ buttons to move a telescope along the DEC direction, ►◄ to move a telescope along the RA direction. Brows the menu or move the cursor in operating menu. Number Keys: Input numerical values. Also used to adjust speeds (1: 1X; 2: 2X; 3: 8X; 4: 16X; 5: 64X; 6: 128X; 7: 256X; 8: 512X; 9: MAX) 10 • • • • • Light Key(☼): Turns on/off the red LED reading light on the back of the controller. ? Key: For help or extra information. STOP/0 Key: Stop/Start tracking. HBX (Handbox) port: connect the HC to MiniTower mount using a 6-wire RJ11 cable. USB port: connect the HC to a Computer via a USB cable. 3.2. The LCD Screen The 8401 HC is designed to use for SmartStar-A GOTO mount and telescopes. It can also be used for iOptron’s equatorial (EQ) mount, such as the SmartStar®-PR GOTO German Equatorial Mount and the GoToNova® Equatorial Kit, as well as all other AltAzimuth (A/A) mounts, which include all SmartStar® GOTO mounts and telescopes. It consists of a large 8-line LCD screen, which displays all the information as shown in Figure 2. The user interface is simple and easy to learn. Figure 2. 8401 HC LCD Information Screen 1. GPS Status: when the power is turned on, it shows “GPS ON”, which means a GPS receiver is connected. When the GPS receiver finds the satellite and receives GPS signal, it shows “GPS OK”. The “GPS OK” will turn off after few minutes. 2. Slew speed: It has 9 speeds: 1X, 2X, 8X, 16X, 64X, 128X, 256X(1º/sec), 512X(2º/sec), MAX(4º/sec). Press SPEED key to change it. 3. Tracking speed: It has 4 speeds: Cel (celestial), Sol (Solar), Lun (Lunar), Def (user defined) 4. Altitude of the telescope (zenith is 90º). 5. Azimuth of the telescope (north is 0º, east 90º, south 180º, and west 270º). 6. Local Date and Time: display local time in a format of YYYY-MM-DD HH:MM:SS. 7. Mount Type: EQ is equatorial and A/A altazimuth. 8. N/S Hemisphere: display the observation hemisphere. 11 4. Getting Started In order to experience the full GOTO capability of GoToNova technology, it is very important to set up the mount correctly before observation. 4.1. Level and Align the Mount 4.1.1. Level the Mount. Leveling is critical for a good GOTO and tracking accuracy. Level the mount by observing the bubble (shown) on the base of the mount by adjusting tripod legs. The bubble should be in the center of the circle. It is also recommended to use additional levelers (such as a torpedo leveler) to assure precise leveling. Turn the mount around by pressing ► or ◄ button to make sure it is always leveled. 4.1.2. Initial Positions Each time the mount is turned on, the default position is Park Position. For the A/A operation mode, its altitude is 90º 00’ 00” and azimuth is 180º 00’ 00”, which means the “SOUTH” mark is pointing to south and the telescope is pointing straight up at the zenith. To set the Park Position, you can: 2) Up 1. Align the mount to south by turning the mount so that 1) South Alt lock (#4) the South mark facing south. An additional compass is needed. Unlock the altitude lock (#4) and rotate the telescope to point straight up at the Zenith. A torpedo level may help. Make sure the mount is leveled. Retighten the altitude lock. Then turn the mount power on. or 2. Turn the mount power on. Press the SPEED button to select a slew speed (MAX for fast slew and 1X for fine tuning). Turn the SOUTH mark pointing to south using ► or ◄ button. An additional compass may be needed. Rotate the telescope point to the zenith using ▲ or ▼ button. A torpedo level may help. Then turn the mount power off and turn it on. 4.2. Setting Up the Mount A SmartStar Cube-A is equipped with a GPS receiver, which will receive the local time, longitude and latitude information from a satellite after the link is established. However, manual input is still needed for time zone and Daylight Saving setting. A clear sky outside is needed for GPS to communicate well with the satellites. 12 4.2.1. Set Up Local Time and Site Info Press MENU button, from the main menu, scroll down and select “Set up controller” Select and Slew Sync. to Target Electronic Focuser Set Up Controller Align Set Up Tracking User Objects Auto Guide Press ENTER. Select “Set Up Local Time” Set Set Set Set Set Set Set Set Up Local Time Up Site N/S Hemisphere Display Contrast Eyepiece Light Backlight Snti-backlash Key Beep Press ENTER. The “Set Local Time” screen will show: Set Local Time: 2009-06-01 11:55:09 300 Min. behind UT Daylight Saving Time Y The local time will be updated when the GPS picks up satellite signals. If for any reason your GPS can’t pick up a signal you can manually enter the time. Press ◄ or ► key to move the cursor and using ▲ or ▼ key to change the number. Press ◄ or ► key, move the cursor to the line below time info to set the time zone information (add or subtract 60 minutes per time zone). Enter minutes “ahead of” or “behind” UT (universal time). • New York City is 300 minutes “behind” UT • Los Angeles is 480 minutes “behind” UT • Rome is 60 minutes “ahead of” UT • Beijing is 480 minutes “ahead of” UT • Sydney is 600 minutes “ahead of” UT All the time zones in North America are behind UT (universal time), as shown in the following table. So make sure it shows “behind” instead of “ahead of” UT. Time Zone Hawaii Alaska Pacific Mountain Central Eastern Hour behind UT -10 -9 -8 -7 -6 -5 Enter Minutes 600 540 480 420 360 300 13 To adjust minutes, move the cursor to each digit and use ▲ or ▼ key to change the number. To change the “behind” or “ahead of” UT, move the cursor to “ahead of” and using ▲ or ▼ key to toggle between “behind” and “ahead of”. For other parts of the world, you can find out your “time zone” information from internet, such as http://www.timeanddate.com/worldclock/. DO NOT COUNT DAYLIGHT SAVING TIME. To set daylight saving time, use the ◄ or ► key to move the cursor to the bottom of the screen, use ▲ or ▼ button to toggle the Daylight Saving Time between N, which means “No” and Y, which means (Yes). Press BACK to go to previous screen. Select “Set Up Site” and press ENTER to check your site info. Set up site info: Longitude: W071d27m47s Latitude: N42d15m40s The longitude and latitude coordinates will be updated when the GPS picks up satellite signals. “W/E” means west/east hemisphere; “N/S” means north/south hemisphere; “d” means degree; “m” means minute; and “s” means second. If for any reason your GPS can’t pick up a signal you can manually enter the GPS coordinates. Press ◄ or ► key to move the cursor and using ▲ or ▼ key to toggle between “W” and “E”, “N” and “S”, or to change the numbers. It is always a good idea to do your home work to get the GPS coordinates before traveling to a new observation site. The site coordinates information can be found from internet, such as GPSVisualizer (http://www.gpsvisualizer.com/geocode), by entering the city name or address. In case you only find the site information in decimal format you can convert them into d:m:s format by multiplying the decimal numbers by 60. For example, N47.53 can be changed to N47º31'48”: 47.53º = 47º +0.53º, 0.53º=0.53x60'=31.8', 0.8'=0.8x60"=48". Therefore, 47.53º=47º31'48" or 47d31m48s. Same as N47º31.8’: 31.8’=31’+0.8’, 0.8’=0.8x60”=48”. 4.2.2. Set Mount Type The SmartStar-A series can be operated in both A/A and EQ mode, for the A/A operation, the mount type needs to be set correctly. Scroll down and select “Set Mount Type”, Set Set Set Set Set Set Set Set Up Site N/S Hemisphere Display Contrast Eyepiece Light Backlight Anti-backlash Key Beep Mount Type 14 Press Enter. Equatorial Mount Alt/Azi Mount Select Alt/Azi mount and press ENTER to go back the previous screen. 4.2.3. Set Anti-backlash For an Alt/Azi operation, both R.A. and DEC anti-backlash should be set to 0 step. Scroll down and select “Set anti-backlash” Set Set Set Set Set Set Set Set Up Local Time Up Site N/S Hemisphere Display Contrast Eyepiece Light Backlight Anti-backlash Key Beep Press ENTER. A R.A. anti-backlash will display: R.A. anti-backlash: 0000 steps One steps equal to 1.5 arc second. To adjust steps move the cursor to each digit and use the number keys to input number directly. Press ENTER – “DEC anti-backlash” will display: DEC anti-backlash: 0000 steps One steps equal to 1.5 arc second. Move the cursor to each digit and use the number keys to set the anti-backlash to 0. Press ENTER to go back the previous screen. Press BACK button to go back to main menu. 15 4.2.4. Using your telescope Selecting an Eyepiece: 1. Always begin viewing with the lowest power eyepiece. (Note: a 25 mm focal length eyepiece has a lower power than a 10 mm one.) A formula can be used to determine the power of each eyepiece: Telescope focal length divided by eyepiece focal length equals magnification. Ex. 400mm ÷ 25mm = 16X (magnification). The rule of thumb is that the magnification should not be too much larger than the OTA aperture, otherwise view and color distortion may occur. 2. A 45° Erecting Diagonal Prism may be included in the R80 or MC90 telescope. The Erecting Diagonal Prism is used to erect the image you will see. Astronomical telescopes are designed in such a way that the image you see may be UPSIDE DOWN and REVERSED. This is perfect for viewing celestial bodies. However, it will feel strange when observing a land object or a bird. Focusing Telescope: 1. After selecting the desired eyepiece aim the telescope tube at a land-based target at least 200 yards away (e.g. A telephone pole or building). Fully extend focusing tube by turning the focus knob. 2. While looking through selected eyepiece, slowly retract focusing tube by turning focusing knob until object comes into focus. Aligning Finderscope: 1. Look through main telescope tube and establish a well-defined target (see focusing telescope section). Tighten all lock knobs (Declination, Latitude, Right Ascension, Horizontal Axis) so that telescope’s aim is not disturbed. 2. Turn on the red dot finder and look through the finder window. Adjust the red dot alignment screws to center the red dot on the object. 3. Now, objects located with the finderscope first will be centered in field of view of the main telescope. 4.2.5. Go to the Moon After performing these setups, the mount is ready to GOTO and track objects. One of the most common objects is the Moon. Press MENU button, select “Select and Slew” by press ENTER button. Select “Planets, Sun, Moon”, and using ▲ or ▼ button to select Moon. Press ENTER. The telescope will automatically slew to the Moon and lock on. It will automatically begin to track once it locks on to it. Use the arrow keys to center the Moon in your eyepiece, if it is not centered. Press BACK key to stop GOTO during the slew. Press ENTER key to stop the tracking. 16 4.2.6. Initial Star Alignment A simple alignment/synchronization can be performed to improve the GOTO and tracking accuracy. To do so, press MENU button, scroll down to “Align”, select “One Star Align” and press ENTER. A list of three bright objects, such as Moon, Venus, and other stars, will be displayed for you to select from. Select an object using ▲ or ▼ key. Then press ENTER. Use ◄ ► ▲ or ▼ key to center the object in your eyepiece. Press SPEED button to change the slew speed if needed. Then press ENTER to complete the alignment. Or press the BACK key to cancel the process. You may need to use SPEED key to change the slewing speed to make the centering procedure easier. An alternate way is performing “Sync to Target”. To do so, press MENU button, select “Select and Slew” and press ENTER. Then select a known sky object, such as Moon from “Planets, Sun, Moon” menu and press ENTER. The mount will slew to the Moon. When the mount stopped slewing, the Moon could be just inside your eyepiece or way off. Press MENU button and scroll down the menu to “Sync to Target” and press ENTER. Follow the instruction, use ◄ ► ▲ and ▼ keys to move the Moon in the center of your eyepiece and press ENTER. 4.3. Turn Off the Mount When finishing observing, always move the mount to Park Position. If the mount is not moved, no initial set up is needed when powered on the next time. To do so, press the MENU button, scroll down to “Park Telescope” and press ENTER. Turn the power off. 17 5. Operate SmartStar® CubeTM-A mount in EQ Mode The SmartStar can precisely track a celestial object while in the alt-az position. The integrated wedge of an A-series telescope allows the telescope to be operated in an equatorial mode, which is a great option for those who want get familiar with the EQ operation. Please Note: the Park Position of an EQ mode is different from that of an A/A mode. Follow the steps below to change the mount from A/A mode to EQ mode: R.A. Axis (azi axle) DEC Axis (alt axle) north-facing tripod leg 1. Make sure that the tripod is leveled while in A/A mode. 2. Align the north-facing tripod leg to the north. 3. Raise the wedge by loosen the tilt locks, until its tilt angle approximately equals to the observation site latitude; 4. Replace the ALT lock with counterweight shaft if a counterweight is needed. 18 5. Align the altitude axle (with or without counterweight) that is pointing straight down, in line with the north-facing tripod leg. This can be done by either loosen the azimuth lock (10) or turn the mount using left or right arrow key. The altitude axle will served as the DEC axis of the EQ mode. 6. Mount the OTA onto the mount and align its optical axis parallel to the azimuth axle of the mount. This can be done by either loosen the altitude lock (4) or turn the mount using up or down arrow key. The azimuth axle will served as the R.A. axis of the EQ mode. 7. Adjust the tilt. Find Polaris in your finder scope and/or your telescope eyepiece. Center it. Lock the tilt into position. 8. In the main menu of your hand controller, select “Set Up Controller”, then select “Set Mount Type”, and select Equatorial mode. 9. Turn off the mount power. Now your SmartStar-A mount is set at the park position of an EQ mode and is ready to observe. 19 6. Use SmartStar® CubeTM-A Telescopes 6.1. Manual Operation of a Telescope You may observe land and astronomical objects using GoToNova’s arrow keys. After the telescope was assembled (referring to Section 2. Telescope Assembly), flip the I/O switch on the telescope mount to turn on the mount. Use ►,◄,▼ or ▲ buttons to point the telescope to desired object. You may need using SPEED key to change the slewing speed. 6.2. Slew to an Object Press MENU button, from the main menu, select “Select and Slew.” Select an object you would like to observe and press ENTER key. The GoToNova® 8401 hand controller has a database consists of over120,000 objects. Use ► or ◄ button to move the cursor and ▼ or ▲ button to change the number. A check mark “√” indicates the object is above the horizon, and cross mark “X” means it is below the horizon. Only those objects above the horizon can be observed. In some catalogs, those stars below the horizon may not be displayed. 6.2.1. Planets, Sun, Moon There are 9 objects in Solar system. 6.2.2. Deep Sky Objects This menu includes objects outside our Solar system such as galaxies, star clusters, quasars, nebulae. • Named Deepsky Objects: It consists of 60 deep sky objects with their common names. A list of named deep sky objects is also attached in Appendix C. • Messier Catalog: It consists of all 110 objects in Messier catalog. • NGC IC Catalog: consists of 7,840 objects in NGC catalog and 5,386 objects in IC catalog. To select an object from NGC or IC catalog, move the cursor to NGC, using▲ or ▼ button to toggle between NGC and IC. Then move the cursor to numerical position and use the number button to select the object. • UGC Catalog: consists of 12,939 objects. • MCG Catalog: consists of 29,004 objects. They are listed numerically from MCG+15 to MCG-05. • Caldwell Catalog: consists of 109 objects. • Abell Catalog: consists of 2,712 objects. • Herschel Catalog: consists of 400 objects. 6.2.3. Comets This catalog contains 190 comets. This database is customer upgradeable. 20 6.2.4. Asteroids I his catalog contains up to 4,096 asteroids. This database is customer upgradeable. 6.2.5. Stars • Named Stars: It consists of 191 stars with their common names. They are listed alphabetically. A list is attached in Appendix C. • Double Stars: It consists of 40 double stars. A list is attached in Appendix C. • SAO Bright Stars: It consists of 26,584 SAO catalog objects. • GCVS Variable Stars: consists of 38,624 GCVS variable stars. They are listed numerically. 6.2.6. Constellations This catalog consists of 88 modern constellations with their names. They are listed alphabetically. A list is attached in Appendix C. 6.2.7. User Objects It can consist up to 256 user predefined objects. These objects need to be entered before they can be selected for slewing. 6.2.8. Enter R.A. DEC Here you can go to a target by entering its R.A. and DEC numbers. 6.3. Sync to Target This operation will match the telescope's current coordinates to Target Right Ascension and Declination. After slew to an object, press MENU—then scroll to “Sync to Target” and press ENTER. Follow the screen to do the sync. Using this function will re-calibrate the computer to the selected object. Multiple syncs can be performed if needed. “Sync to Target” will only work after “Select and slew” is performed. Otherwise, the system may perform incorrectly. You can change the slewing speed to make the centering procedure easier. Simply press a number (1 through 9) to change the speed. The default slew speed is 64X. “Sync to Target” has the similar performance that “One Star Align” has and will greatly improve the GOTO accuracy locally. It is very useful for finding a faint object near a bright star. 6.4. Electric Focuser N/A 21 6.5. Set Up Controller 6.5.1. Set Up Local Time Refer to 4.2.1. 6.5.2. Set Up Site Refer to 4.2.1. 6.5.3. Set N/S Hemisphere Set northern or southern hemisphere. 6.5.4. Set Display Contrast Use arrow keys to adjust LCD display contrast. 6.5.5. Set Eyepiece Light If you have an illuminated-reticule eyepiece or illuminated polar scope, and it is supported by GoToNova hand controller-- use this option to adjust the light intensity. 6.5.6. Set Backlight Adjust LCD and keypad backlight. 6.5.7. Set Anti-backlash Use Array Keys to move the cursor and Number Keys to change the number. 0 is suggested for Alt/Azi mount. For an EQ mount, the default setting is 150 for both DEC and R.A. 6.5.8. Set Key Beep Turn the key beep on/off. 6.5.9. Set Mount Type Set the mount as Equator Mount or Alt/Azi Mount. 6.5.10. Reset All Reset all settings to factory default data. 6.5.11. Update Firmware Firmware updating using iOptron Downloader through USB port on hand controller. (Refer to Appendix E.) 6.5.12. Set gear ratio Not supported. 22 6.5.13. Set Language Select hand controller display language in English or French. 6.6. Align This function is used for align the telescope. Before star alignment, please make sure the mount is well leveled. The system also provides “One Star Align” and “Two Star Align”. Any one can be selected for telescope alignment. 6.6.1. One Star Align From the main menu, select “Align”. Select “One Star Align” and press ENTER. Three most popular objects, such as Moon, a planet or a bright star that are above the horizon will be provided for selection. Use ▲ or ▼ button to select an alignment star and press ENTER. Then manually slew the telescope to the object and center the object in your eyepiece using ◄ ► ▲ or ▼ key. Press SPEED button to adjust the slew speed. Then press ENTER to complete the alignment. Or press the BACK key to cancel the process. If you have a very good initial setup, one star alignment should be sufficient for good GOTO accuracy. To increase the accuracy you may choose to do two star alignment. 6.6.2. Two Star Alignment Two star alignment will increase the GOTO accuracy of the mount. It is suggested to do two star alignment after one star alignment. Two star alignment requires a wider view of the sky, since the two align stars need to be far apart. Select “Two Star Align” in the Align menu. When you finish the first star, the system will prompt you to choose the second star. If the star you choose is too close to the first one, the system will let you choose another one. When you are aligned with the second star, two star alignment is finished. You can reject the suggested star if it is blocked by the tree or behind the house. “Two Star Align” result will be overridden if “One Star Align” or “Sync. to Target” is performed after “Two Star Align.” 6.6.3. Three-Star Align N/A. 6.6.4. Dis R.A axis error This only works for EQ mode. This displays the pointing error between the R.A. axis and the polar axis. When the HC shows, for example: 7.5" lower 4.3" east, 23 it means the polar axis of the mount is pointing 7.5” lower and 4.3” to the east to the North Pole. Pointing error is zero when you power on the mount (unless you “Park Telescope” before powering off). 6.6.5. Test Anti-backlash This command tests the backlashes in both R.A. and DEC. The saved numbers will show in “Set Anti-backlash” menu. However, if no high accuracy is needed or your equatorial mount is not a high accuracy unit (i.e. the worm gear has different clearance in different positions), you can omit this procedure. 6.6.6. Polaris Position Polaris is NOT at the exact point of the Polar Axis. This shows the offset (about 40 min) between the Polaris and the actual Celestial Pole (Polar Axis), as well as the direction of the Polaris to the Polar Axis at the observing location. 6.7. PEC Option Not supported. 6.8. Set Up Tracking A user can set up tracking in the main menu by selecting “Set up tracking”. Then the user can select “Sidereal speed”, “Solar speed”, “Lunar speed”, and “User defined speed”. For “User defined speed” this can be adjusted from 91% to 109% of sidereal speed by pressing the ▲or ▼ buttons. 6.9. User Object List Besides various star lists available in the hand controller, users can add, edit or delete defined objects. All data you enter is supposedly J2000.0 epoch. 6.10. Auto Guide This function is not supported in Alt/Azi mode. 6.11. Park Scope This procedure only needs to be done if you do not move your telescope mount after you power off the GoToNova. Celestial pole pointing error will be stored to flash memory and recalled when you power on again. 6.12. To Park Position This moves your telescope to park position. When power is turned on, the mount assumes the physical position is the park position. This is its reference point for all other objects. 24 7. Maintenance and Servicing 7.1. Maintenance The SmartStar® Cube-A mount or telescope is a precision instrument designed to yield a lifetime of rewarding applications. Given the care and respect due any precision instrument, your telescope will rarely require factory servicing or maintenance. Maintenance guidelines include: 1. Using wet cloth to clean the mount and hand controller. Do not use the solvent. 2. Leave the dust cap on while not operating the telescope. Avoid cleaning the telescope’s optics. A little dust on the front surface of the telescope’s correcting lens causes virtually no degradation of image quality and should not be considered a reason to clean the lens. 3. When absolutely necessary, dust on the front lens should be removed with gentle strokes of a camel hair brush, a soft glass clean cloth or blown off with an ear syringe (available at any pharmacy). Do not use a commercial photographic lens cleaner. 4. Organic materials (e.g., fingerprints) on the front lens may be removed with a solution of 3 parts distilled water to 1 part isopropyl alcohol. Use soft, white facial tissues or cotton balls and make short, gentle strokes. Change tissues often. Do not use scented, colored, or lotioned tissues as damage could result to the optics. 5. If your telescope is used outdoors on a humid night, telescope surfaces may accumulate water condensation. While such condensation does not normally cause any damage to the telescope, it is recommended that wait the entire telescope be dried before being packed away. Do not wipe any of the optical surfaces. In addition, the dust cap should not be placed back on to the optical tube until the telescope is thoroughly dry. 6. If your telescope is not to be used for an extended period, perhaps for one month or more, it is advisable to remove the batteries from battery holder, if they are installed. Batteries left installed for prolonged periods may leak, causing damage to the telescope’s electronic circuitry. 7. Do not leave your telescope outdoors on a warm day or inside a sealed car for an extended period of time. Excessive ambient temperatures can damage the telescope’s internal lubrication and electronic circuitry. 7.2. Storage and Transport When not in use, store the telescope in a cool, dry place. Do not expose the instrument to excessive heat or moisture. It is best to store the telescope in its original box with the altitude lock knob unlocked. If shipping the telescope, use the original box and packing material to protect the telescope during shipment. When transporting the telescope, take care not to bump or drop the instrument; this type of abuse can damage the optics or affect the GOTO tracking accuracy. 25 7.3. Troubleshooting The following suggestions may be helpful with operation of the SmartStar® Cube-A mount or telescope. The power indicator light on the mount does not come on or there is no response when pressing hand controller’s arrow keys: (1) Verify that the power switch on the mount is in the ON position. (2) Verify that the hand controller cord is firmly connected to the HBX port on the mount, or switch the cord to the other HBX port. (3) Check the power source, which include: • Using the battery? Are the batteries installed correctly? Are the batteries fresh? How long have they been used? (frequent slew and GOTO will deplete battery power very quickly) • Using AC or DC adapter? Check the plugs to the mount and to the power outlet. • Using extension cord? Make sure the cord is in good condition. Power drop along the extension cord was known to cause the problem. Also check all the plugs and connections. (4) If the telescope does not respond to commands, set the power switch to OFF and then back to ON. (5) If the telescope does not slew after power is applied or if the motor quits or stalls, verify that there are no physical obstructions that would impede telescope movement. Cannot seem to focus (No image appears in the eyepiece): (1) Confirm that the dust cap has been removed from the telescope. (2) Keep turning the focus knob. Your telescope has a fine focusing mechanism which allows you to focus an image very precisely. However, this means that you may have to rotate the focus knob 20 to 40 complete turns to achieve focus, particularly the first time you use your telescope. After that, fewer turns will be needed. Images through the eyepiece appear unfocused or distorted: (1) The magnification used may be too high for the seeing conditions. Back off to a lower power eyepiece. (2) If inside a warm house or building, move outside. Interior air conditions may distort terrestrial (land) or celestial images, making it difficult, if not impossible, to obtain a sharp focus. For optimal viewing, use the telescope outside in the open air instead of observing through an open or closed window or screen. (3) If viewing a land object on a warm day, heat waves distort the image. (4) The optics within the telescope need time to adjust to the outside ambient temperature to provide the sharpest image. To "cool down" the optics, set the telescope outside for 10 to 15 minutes before observing begins. Error Message “Warning! DEC. (or R.A.) driver motor over current. Please check balance.” (1) Check if the mount or OTA is blocked by any obstructions. (2) Try to operate the mount without an OTA. (3) Check the power supply. This is a common reason for this message and unexpected slew behavior or movement. which include: • Batteries: Are the batteries fresh? How long have they been used? (frequent slewing and GOTO will deplete battery power very quickly) • AC or DC adapter: Check the plugs to the mount and to the power outlet. 26 • Extension cord: Make sure the cord is in good condition. Power drop along the extension cord has been known to cause this error message. Also check all the plugs and connections. (4) Check the hand controller cord. Unplug it and re-plug into the other HBX port. Error Message “Warning! Can not communicate with DEC motor controller.” (1) Check the hand controller cord. Unplug it and re-plug into another HBX port. (2) Check the power supply, which include: • Using the battery? Is the battery fresh? How long it has been used? (frequent slew and GOTO will deplete battery power very quickly) • Using AC or DC adapter? Check the plugs to the mount and to the power outlet. • Using extension cord? Make sure the cord is in good condition. Power drop along the extension cord was known to cause the problem. Also check all the plugs and connections. The object is jumping up and down in the eyepiece or over-slewed, and other unexpected slew behavior or movement. (1) Use most updated firmware. (2) Set backlash to 0 in both DEC and RA. (3) Check the power supply, which include: • Using the battery? Is the battery fresh? How long it has been used? (frequent slew and GOTO will deplete battery power very quickly) • Using AC or DC adapter? Check the plugs to the mount and to the power outlet. • Using extension cord? Make sure the cord is in good condition. Power drop along the extension cord was known to cause the problem. Also check all the plugs and connections. (4) System balancing. The telescope does not GOTO the right object, or the alignment is always wrong: (1) Leveling (very important). (2) Site information (minutes “ahead of “or “behind” UT, DST). (3) System balancing. (4) Use most updated firmware. (5) Select right mount type (A/A or EQ). (6) Starting form backlash of 0 in both DEC and RA. (7) Check the power supply, which include: y Using the battery? Is the battery fresh? How long it has been used? (frequent slew and GOTO will deplete battery power very quickly) y Using AC or DC adapter? Check the plugs to the mount and to the power outlet. y Using extension cord? Make sure the cord is in good condition. Power drop along the extension cord was known to cause the problem. Also check all the plugs and connections. 7.4. iOptron Customer Service If you have a question concerning your telescope, contact the iOptron Customer Service Department. Customer Service hours are 9:00 AM to 5:00 PM, Easter Time, Monday through Friday. In the unlikely event that the telescope requires factory servicing or repairs, write or call the iOptron Customer Service Department first, before returning the telescope to the factory, giving full particulars as to the nature of the problem, as well as your name, address, and 27 daytime telephone number. The great majority of servicing issues can be resolved by telephone, avoiding return of the telescope to the factory. It is also strongly support@ioptron.com. suggested that 28 to send your technical questions to Appendix A. Technical Specifications SmartStar® CubeTM-A GOTO Mount Mount Body Materials Motor Gear Bearing Slew Speed GOTO System Processor Object in Database GOTO accuracy Tracking Payload Battery Power Requirement Operating Temperature Weight with tripod AltAzimuth/Equatorial Dual Mount Die-cast Aluminum Dual-Axis DC Servo motor with encoders Acetal worm wheel/Nylon 6 worm gear 4 steel ball bearings Dual-Axis, 9-Gear, Electronic (1X,2X,8X,16X,64X,128X,256X,512X,MAX) GoToNova® 8401 32bit ARM 120,000 + 1 Arc Min. (Typical) Automatic 7 lbs AA x 8(Not Included) DC 12V±2V, >1.2A 0 ~ 40ºC 5.5 lbs (without OTA) Refractor Telescope Optical Design Clear Aperture Focal Length Focal Ratio Resolving Power Weight Achromatic Refractor 80 mm 400 mm f/5 1.4 arc sec 2.2 lbs Newtonian Reflector Telescope Optical Design Clear Aperture Focal Length Focal Ratio Resolving Power Finderscope Weight Reflector 114 mm 1000 mm f/8.8 1 arc sec Red dot 4 lbs Maksutov-Cassegrain Telescope Optical Design Clear Aperture Focal Length Focal Ratio Resolving Power Finderscope Weight Maksutov-Cassegrain 90 mm 1200 mm f/13.3 1.3 arc sec Red dot 4 lbs 29 Appendix B. GoToNova® 8401 HC MENU STRUCTURE MENU Select and Slew Planets, Sun, Moon Mercury Venus Mars Jupiter Saturn Uranus Neptune Pluto Sun Moon Deep Sky Objects Named Deepsky Object Messier Catalog NGC IC Catalog UGC Catalog MCG Catalog Caldwell Catalog Abell Catalog Herschel Catalog Comets Asteroids Stars Named Stars Double Stars GCVS Variable Stars SAO Catalog Constellations User Objects Enter R.A. and DEC Sync. To Target Electric Focuser Focus Set Anti-backlash 30 Set Up Controller Set Up Local Time Set Up Site Set N/S Hemisphere Set Display Contrast Set Eyepiece Light Set Backlight Set Anti-backslash Set Key Beep Set Mount Type Reset All Upgrade Firmware Set Gear Ratio Set Language Align Easy One Star Align One Star Align Two Star Align Three Star Align Disp. R.A. Axis Error Test Anti-backslash Polaris Position PEC Option PEC Play Back Record PEC Delete PEC Record Set Up Tracking Sidereal Speed Solar Speed Lunar Speed User Defined Speed User Objects Add A New Record Modify Records Delete One Record Erase All Records Auto Guide Park Scope To Park Position 31 Appendix C. GoToNova® Star List GoToNova Deep Sky Object List for 8401 ID No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 OBJECT Andromeda Galaxy Barnards Galaxy Beehive Cluster Blackeye Galaxy Blinking Planetary Nebula Blue Flash Nebula Blue Planetary Blue Snowball Nebula Box Nebula Bubble Nebula Bipolar Nebula Butterfly Cluster California Nebula Cat's Eye Nebula Cocoon Nebula Cone Nebula Cork Nebula Crab Nebula Crescent Nebula Draco Dwarf Duck Nebula Dumbbell Nebula Eagle Nebula Eight-Burst Nebula Eskimo Nebula Flaming Star Nebula Ghost of Jupiter Great Cluster Helix Nebula Hercules Galaxy Cluster Hind's Variable Nebula Hubble's Variable Nebula Integral Sign Galaxy Jewel Box Cluster Keyhole Nebula NGC # 224 6822 2632 4926 6826 6905 3918 7662 6309 7635 6302 6405 1499 6543 Messier # 31 IC# A(Abell) U(UGC) 44 64 6 5146 2264 650-51 1952 6888 76 1 10822 2359 6853 27 16 3132 2392 405 3242 6205 7293 13 2151 1555 2261 3697 4755 3372 32 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 Lagoon Nebula Little Gem Little Gem Nebula Little Ghost Nebula North American Nebula Omega Nebula Orion Nebula Owl Nebula Pelican Nebula Phantom Streak Nebula Pinwheel Galaxy Pleiades Ring Nebula Ring Tail Galaxy Rosette Nebula Saturn Nebula Sextans B Dwarf Small Magellanic Cloud Sombrero Galaxy Spindle Galaxy Tank Track Nebula Trifid Nebula Ursa Minor Dwarf Whirlpool Galaxy Wild Duck Cluster 6523 6445 6818 6369 7000 6618 1976 3587 8 17 42 97 5070 6741 598 6720 4038 2237 7009 33 45 57 5373 292 4594 3115 2024 6514 104 20 9749 5194 6705 33 51 11 Messier This table is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article List of Messier objects 34 Modern Constellations No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Constellation Andromeda Antlia Apus Aquarius Aquila Ara Aries Auriga Boötes Caelum Camelopardalis Cancer Canes Venatici Canis Major Canis Minor Capricornus Carina Cassiopeia Centaurus Cepheus Cetus Chamaeleon Circinus Columba Coma Berenices Corona Australis Corona Borealis Corvus Crater Crux Cygnus Delphinus Dorado Draco Equuleus Eridanus Fornax Gemini Grus Hercules Horologium Hydra Hydrus Indus Abbreviation And Ant Aps Aqr Aql Ara Ari Aur Boo Cae Cam Cnc CVn CMa CMi Cap Car Cas Cen Cep Cet Cha Cir Col Com CrA CrB Crv Crt Cru Cyg Del Dor Dra Equ Eri For Gem Gru Her Hor Hya Hyi Ind No. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 35 Constellation Lacerta Leo Leo Minor Lepus Libra Lupus Lynx Lyra Mensa Microscopium Monoceros Musca Norma Octans Ophiuchus Orion Pavo Pegasus Perseus Phoenix Pictor Pisces Piscis Austrinus Puppis Pyxis Reticulum Sagitta Sagittarius Scorpius Sculptor Scutum Serpens Sextans Taurus Telescopium Triangulum Triangulum Australe Tucana Ursa Major Ursa Minor Vela Virgo Volans Vulpecula Abbreviation Lac Leo LMi Lep Lib Lup Lyn Lyr Men Mic Mon Mus Nor Oct Oph Ori Pav Peg Per Phe Pic Psc PsA Pup Pyx Ret Sge Sgr Sco Scl Sct Ser Sex Tau Tel Tri TrA Tuc UMa UMi Vel Vir Vol Vul GoToNova Named Star List 001 Acamar 002 Achernar 003 Acrux 004 Acubens 005 Adhafera 006 Adhara 007 Al Na’ir 008 Albali 009 Alberio 010 Alchibar 011 Alcor 012 Alcyone 013 Aldebaran 014 Alderamin 015 Alfirk 016 Algedi 017 Algenib 018 Algiebra 019 Algol 020 Algorab 021 Alhena 022 Alioth 023 Alkaid 024 Alkalurops 025 Alkes 026 Almach 027 Alnasl 028 Alnilam 029 Alnitak 030 Alphard 031 Alphecca 032 Alpheratz 033 Alrakis 034 Alrescha 035 Alshain 036 Altair 037 Altais 038 Alterf 039 Aludra 040 Alula Australis 041 Alula Borealis 042 Alya 043 Ancha 044 Ankaa 045 Antares 046 Arcturus 047 Arkab 048 Arneb 049 Ascella 050 Asellus Australis 051 Asellus Borealis 052 Aspidiske 053 Atik 054 Atlas 055 Atria 056 Avoir 057 Azha 058 Baten Kaitos 059 Beid 060 Bellatrix 061 Betelgeuse 062 Biham 063 Canopus 064 Capella 065 Caph 066 Castor 067 Celabrai 068 Celaeno 069 Chara 070 Chertan 071 Cor Caroli 072 Cursa 073 Dabih 074 Deneb 075 Deneb Algedi 076 Deneb Kaitos 077 Denebola 078 Dubhe 079 Edasich 080 Electra 081 Elnath 082 Eltanin 083 Enif 084 Errai 085 Fomalhaut 086 Furud 087 Gacrux 088 Giausar 089 Gienah 090 Gomeisa 091 Graffias 092 Groombridge 1830 093 Grumium 094 Hamal 095 Homan 096 Izar 097 Kaus Australis 098 Kaus Borealis 099 Kaus Media 100 Keid 101 Kitalpha 102 Kochab 103 Kornephoros 104 Kurhah 105 Lesath 106 Maia 107 Marfik 108 Markab 109 Matar 110 Mebsuta 111 Megrez 112 Meissa 113 Mekbuda 114 Menkalinan 115 Menkar 116 Menkent 117 Menkib 118 Merak 119 Merope 120 Mesartim 121 Miaplacidus 122 Mintaka 123 Mira 124 Mirach 125 Mirfak 126 Mirzam 127 Mizar 128 Muphrid 129 Muscida 130 Nashira 131 Nekkar 132 Nihal 133 Nunki 134 Nusakan 135 Peacock 136 Phact 137 Phecda 138 Pherkad 139 Pleione 140 Polaris 141 Pollux 142 Porrima 143 Procyon 144 Propus 36 145 Rassalas 146 Rasagethi 147 Rasalhague 148 Rastaba 149 Regulus 150 Rigel 151 Rigel Kentaurus 152 Ruchbah 153 Rukbat 154 Sabik 155 Sadachbia 156 Sadalbari 157 Sadalmelik 158 Sadalsuud 159 Sadr 160 Saiph 161 Scheat 162 Schedar 163 Seginus 164 Shaula 165 Sheiak 166 Sheratan 167 Sirius 168 Skat 169 Spica 170 Sterope 171 Sulafat 172 Syrma 173 Talitha 174 Tania Australis 175 Tania Borealis 176 Tarazed 177 Taygeta 178 Thuban 179 Unukalhai 180 Vega 181 Vindemiatrix 182 Wasat 183 Wazn 184 Yed Posterior 185 Yed Prior 186 Zaniah 187 Zaurak 188 Zavijava 189 Zosma 190 Zubenelgenubi 191 Zubeneschamali GoToNova Double Star List No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Object Eta Alpha Theta Alpha Alpha Sigma Mu Alpha Delta Alpha Alpha Epsilon HR 3579 Kapa Psi Gamma HR 4167 Mu Alpha Zeta Iota Gamma Gamma Beta HR 5089 Alpha Zeta Gamma Gamma Xi Alpha Lambda Zeta Eta 70 Zeta Delta Beta Tau Epsilon Const Cas Psc Per For Aur Ori Ori CMa Gem Gem CMi Hya UMa Vel Leo Vel UMa UMa Leo Cen Vir Mus Cen Boo Lup CrA Sco Sco Oph Her Oph Oph Sgr Cyg Del Cyg Lyr 37 SAO 21732 110291 38288 168373 40186 132406 113389 151881 79294 60198 115756 117112 42642 42661 221234 81298 222199 222321 15384 28737 99587 223603 138917 252019 204545 252838 101145 225938 83958 159665 184415 121658 65485 160332 123107 187600 48796 106316 71121 67310 Name Achird Alrisha Fornacis Capella Sirius Wasat Castor Algieba Dubhe Mizar Porrima Antares Marfic Sabik Ascella Rotanev double double Appendix D. Set Up USB-PC Connection 1. Download USB2COM driver (cp2102.zip file for 8401) from iOptron Website 2. Install CP210x (usb2com) driver Choose the appropriate driver for your OS. In this case is a Windows XP operation system. Double click on it, and you will see: Click “Next”. 38 Select “I accept the terms of license agreement”, and click “Next” Using the default installation path, c:\SiLabs\MCU\CP210x, or specify your own path by click “Change”. Click “Next”. Then click “Install”. 39 When finished installation, click “Finish” 3. Plug the USB cable in to the USB port on your PC, plug the other end of the USB cable to hand controller. Turn on the power on the mount. 4. Install the Hardware The computer will find a new hardware and show the following screen Select “No, not this time” and click “Next”. 40 Select “Install from a list or specific location” and click “Next”. Select “Search for the best driver in these locations,” and check “Include this location in the search.” Click on “Browse” and select the CP210x driver from directory c:\SiLabs\MCU\CP210x\Win2K_XP, click OK. 41 Click “Next”. The computer will start to install the driver for the USB2COM. When the installation is done, click “Finish”. If the computer shows “find a new hardware” screen again, just repeat the steps in this section again. 42 Now you computer should be ready for Firmware Upgrading, computer communication with the mount via ASCOM platform and planetarium software applications. However, you need to find assigned COM port number for the USB connection. To do so, right click “My Computer”, and click “Properties” Click “Hardware”, click “Device Manager” 43 Double click on “Ports(COM & LPT)”, find out the COM number and write it down (in the following figure, it is COM3) 44 Appendix E. Firmware Upgrade 1. Download and install Firmware Downloader from iOptron Website 2. Double click and open “iOptron Downloader” On the interface, select appropriate port using pull-down menu (in this case, COM3): 45 Click “Open Data File”, and select appropriate “.bin” file that matches your hand controller, and click “Open”. Select “Main Program” ONLY in Update Type. Click “Start Download”. iOptronDownload will display: “Please reset GoToNova[GOTOSTAR], waiting for connection…” On the hand controller, press “MENU”, and using ▼▲ scroll to select “Set up controller”, press “ENTER”, then select “Upgrade firmware”, press “ENTER” and the upgrade starts. 46 Now the upgrade is finished. Typical Errors: 1. Invalid Port Number: in Device Manager, make sure you have the correct COM port number for CP210x. 2. Wrong “.bin” file: make sure you have the correct “.bin” file for firmware upgrade. 3. Wrong downloader, you should use iOptron Downloader instead of the Flash Downloader. 4. Use CP210x driver provided by iOptron. The newest version from SiLab may not work properly for iOptron’s hand controller. What can I do if the firmware is not loading or the screen is blank, due to any reason? y Turn on the mount to power on the hand controller (the key pad should be lit) y Click on the iOptron Downloader. Change the Serial Port to the right COM port in the pull-down menu (example: COM4) y Click on Open Data ile(O) button to select the right Firmware for your hand controller. (example: 8401_Ver090701.bin) y DON’T click on Start Download (D) button yet. Turn the mount power off. y Turn the mount power back on. Right after hearing the “beep”, click on Start Download (D) button. The timing is very important. The downloading process will begin y When the download is successfully finished, turn the mount off and back on to check the hand controller. Double check the settings, such as time and site info, mount type, anti-backlash, to see if they are changed y You may need to practice a few times to get the procedure work correctly. 47 Appendix F. Use a PC to Control an iOptron Mount In general you need the followings to use a PC to control a SmartStar-A mount, 1. Download USB2COM driver (CP210x.zip file for 8401) http://www.ioptron.com/support.aspx?catalog=28; 2. Install USB2COM and establish the connection between the mount and the PC (see instruction); 3. ASCOM platform (download from http://ascom-standards.org/); 4. iOptron ASCOM drive (download it from iOptron website; and 5. Planetarium software. Some company has integrated iOptron’s products into their planetarium software, such as Voyage and The Sky X Pro. Therefore, an ASCOM plug-in will not be needed. Most planetarium software can be used to control iOptron’s product via ASCOM. Some other ASCOM drivers, such as LX200 Generic ASCOM driver and AstroPhysics GTO driver, are also compatible to SmartStar® mount. 48
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2012:06:01 18:53:43-04:00 Create Date : 2012:06:01 18:53:43-04:00 Format : application/pdf Title : Microsoft Word - SmartStar A Series Instruction v2.1-8401.doc Creator : Kevin Zou Document ID : uuid:d98f2d32-8f4b-4b7f-9994-3199fbc87492 Instance ID : uuid:c2897d9d-a470-4f38-8dac-0c7e2f26cd6e Page Count : 48 Author : Kevin ZouEXIF Metadata provided by EXIF.tools